| Age | Commit message (Collapse) | Author |
|---|
|
gpiod_get_array_optional() for spk-id GPIOs can return NULL, if they are
missing, so do not pass the value to PTR_ERR but instead explicitly
treat NULL as acceptable condition. The old code was correct, but
misleading because PTR_ERR usually is used on errors.
Reported by Smatch:
drivers/spi/spi-cs42l43.c:241 cs42l43_get_speaker_id_gpios() warn: passing zero to 'PTR_ERR'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250501-n-smatch-fixes-v2-2-d2ad9c1f2e67@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On dma_request_chan() failure driver NULL-ifies the 'rx_chan' and
immediately uses it as PTR_ERR() so dev_err_probe() prints incorrect
error code. Rework the code so proper error code will be printed and
NULL-ifying of 'rx_chan' will happen in common error handling block
(failure of DMA setup is not fatal for the driver and further code
depends on 'rx_chan' being non-NULL for DMA operations).
Reported by Smatch:
drivers/spi/atmel-quadspi.c:1287 atmel_qspi_dma_init() warn: passing zero to 'PTR_ERR'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250501-n-smatch-fixes-v2-1-d2ad9c1f2e67@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Apply De Morgan's Theorem and drop superfluous parentheses to simplify
the check for strange loopback values.
While at it, add the missing zero in the related comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/da612090f543c8c7cc99fb9dc6ef4abc9560abe4.1746184293.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from David Lechner <dlechner@baylibre.com>:
In order to achieve a 4 MSPS rate on a 16-bit ADC with a 80 MHz SCLK
using the SPI offload feature of the AXI SPI Engine, we need to shave
off some time that is spent executing unnecessary instructions. There
are a few one-time setup instructions that can be moved so that they
execute only once when the SPI offload trigger is enabled rather than
repeating each time the offload is triggered. Additionally, a recent
change to the IP block allows dropping the SYNC instruction completely.
With these changes, we are left with only the 3 instructions that are
needed to to assert CS, transfer the data, and deassert CS. This makes
3 + 16 * 12.5 ns = 237.5 ns < 250 ns which is comfortably within the
available time period.
|
|
Add optimization to omit SYNC instructions from offload messages.
Starting with IP core v1.5.0, the SYNC instruction is no longer required
for proper operation when using the offload feature. Omitting the SYNC
instruction saves a few clock cycles needed to executed which can e.g.
allow achieving higher sample rates on ADCs.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250428-adi-main-v1-4-4b8a1b88a212@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add an optimization to avoid repeating bits_per_word instructions in
each message when using SPI offload. This only applies when all data
xfers in a message have the same bits_per_word. In this case, we can
execute the instruction that sets bits_per_word when the offload trigger
is enabled. This is useful e.g. for obtaining higher sample rates on
ADCs since each message takes less time to execute.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250428-adi-main-v1-3-4b8a1b88a212@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add an optimization to avoid repeating the config instruction in each
SPI message when using SPI offloading. Instead, the instruction is
run once when the SPI offload trigger is enabled.
This is done to allow higher sample rates for ADCs using this SPI
controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250428-adi-main-v1-2-4b8a1b88a212@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a polling wait for SPI instruction execution to complete in the
spi_engine_setup() function. In practice, these instructions complete
in a few 10s of nanoseconds, so we never ran into any race conditions,
but it is good practice to wait for the completion of the SPI engine
instructions before returning from the setup function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250428-adi-main-v1-1-4b8a1b88a212@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- When releasing a start-aligned resource, e.g., a bridge window, save
start/end/flags for the next assignment attempt; fixes a v6.15-rc1
regression (Ilpo Järvinen)
- Move set_pcie_speed.sh from TEST_PROGS to TEST_FILE; fixes a bwctrl
selftest v6.15-rc1 regression (Ilpo Järvinen)
- Add Manivannan Sadhasivam as maintainer of native host bridge and
endpoint drivers (Manivannan Sadhasivam)
- In endpoint test driver, defer IRQ allocation from .probe() until
ioctl() to fix a regression on platforms where the Vendor/Device ID
match doesn't include driver_data (Niklas Cassel)
* tag 'pci-v6.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
misc: pci_endpoint_test: Defer IRQ allocation until ioctl(PCITEST_SET_IRQTYPE)
MAINTAINERS: Move Manivannan Sadhasivam as PCI Native host bridge and endpoint maintainer
selftests/pcie_bwctrl: Fix test progs list
PCI: Restore assigned resources fully after release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Fix crashes in the gic-v2m irqchip driver, caused by an incorrect
__init annotation"
* tag 'irq-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()
|
|
Pull drm fixes from Dave Airlie:
"Weekly drm fixes, mostly amdgpu, with some exynos cleanups and a
couple of minor fixes, seems a bit quiet, but probably some lag from
Easter holidays.
amdgpu:
- P2P DMA fixes
- Display reset fixes
- DCN 3.5 fixes
- ACPI EDID fix
- LTTPR fix
- mode_valid() fix
exynos:
- fix spelling error
- remove redundant error handling in exynos_drm_vidi.c module
- marks struct decon_data as const in the exynos7_drm_decon driver
since it is only read
- Remove unnecessary checking in exynos_drm_drv.c module
meson:
- Fix VCLK calculation
panel:
- jd9365a: Fix reset polarity"
* tag 'drm-fixes-2025-04-26' of https://gitlab.freedesktop.org/drm/kernel:
drm/exynos: Fix spelling mistake "enqueu" -> "enqueue"
drm/exynos: exynos7_drm_decon: Consstify struct decon_data
drm/exynos: fixed a spelling error
drm/exynos/vidi: Remove redundant error handling in vidi_get_modes()
drm/exynos: Remove unnecessary checking
drm/amd/display: do not copy invalid CRTC timing info
drm/amd/display: Default IPS to RCG_IN_ACTIVE_IPS2_IN_OFF
drm/amd/display: Use 16ms AUX read interval for LTTPR with old sinks
drm/amd/display: Fix ACPI edid parsing on some Lenovo systems
drm/amdgpu: Allow P2P access through XGMI
drm/amd/display: Enable urgent latency adjustment on DCN35
drm/amd/display: Force full update in gpu reset
drm/amd/display: Fix gpu reset in multidisplay config
drm/amdgpu: Don't pin VRAM without DMABUF_MOVE_NOTIFY
drm/amdgpu: Use allowed_domains for pinning dmabufs
drm: panel: jd9365da: fix reset signal polarity in unprepare
drm/meson: use unsigned long long / Hz for frequency types
Revert "drm/meson: vclk: fix calculation of 59.94 fractional rates"
|
|
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca28 ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Damien Le Moal:
- Fix the incorrect return type of ata_mselect_control_ata_feature()
- Several fixes for the control of the Command Duration Limits feature
to avoid unnecessary enable and disable actions. Avoiding the
unnecessary enable action also avoids unwanted resets of the CDL
statistics log page as that is implied for any enable action.
- Fix the translation for sensing the control mode page to correctly
return the last enable or disable action performed, as defined in
SAT-6. This correct mode sense information is used to fix the
behavior of the scsi layer to avoid unnecessary mode select command
issuing.
* tag 'ata-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
scsi: Improve CDL control
ata: libata-scsi: Improve CDL control
ata: libata-scsi: Fix ata_msense_control_ata_feature()
ata: libata-scsi: Fix ata_mselect_control_ata_feature() return type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- For some reason we went from zero to three maintainers for HFS/HFS+
in a matter of days. The lesson to learn from this might just be that
we need to threaten code removal more often!?
- Fix a regression introduced by enabling large folios for lage logical
block sizes. This has caused issues for noref migration with large
folios due to sleeping while in an atomic context.
New sleeping variants of pagecache lookup helpers are introduced.
These helpers take the folio lock instead of the mapping's private
spinlock. The problematic users are converted to the sleeping
variants and serialize against noref migration. Atomic users will
bail on seeing the new BH_Migrate flag.
This also shrinks the critical region of the mapping's private lock
and the new blocking callers reduce contention on the spinlock for
bdev mappings.
- Fix two bugs in do_move_mount() when with MOVE_MOUNT_BENEATH. The
first bug is using a mountpoint that is located on a mount we're not
holding a reference to. The second bug is putting the mountpoint
after we've called namespace_unlock() as it's no longer guaranteed
that it does stay a mountpoint.
- Remove a pointless call to vfs_getattr_nosec() in the devtmpfs code
just to query i_mode instead of simply querying the inode directly.
This also avoids lifetime issues for the dm code by an earlier bugfix
this cycle that moved bdev_statx() handling into vfs_getattr_nosec().
- Fix AT_FDCWD handling with getname_maybe_null() in the xattr code.
- Fix a performance regression for files when multiple callers issue a
close when it's not the last reference.
- Remove a duplicate noinline annotation from pipe_clear_nowait().
* tag 'vfs-6.15-rc4.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs/xattr: Fix handling of AT_FDCWD in setxattrat(2) and getxattrat(2)
MAINTAINERS: hfs/hfsplus: add myself as maintainer
splice: remove duplicate noinline from pipe_clear_nowait
devtmpfs: don't use vfs_getattr_nosec to query i_mode
fix a couple of races in MNT_TREE_BENEATH handling by do_move_mount()
fs: fall back to file_ref_put() for non-last reference
mm/migrate: fix sleep in atomic for large folios and buffer heads
fs/ext4: use sleeping version of sb_find_get_block()
fs/jbd2: use sleeping version of __find_get_block()
fs/ocfs2: use sleeping version of __find_get_block()
fs/buffer: use sleeping version of __find_get_block()
fs/buffer: introduce sleeping flavors for pagecache lookups
MAINTAINERS: add HFS/HFS+ maintainers
fs/buffer: split locking for pagecache lookups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dave Jiang:
"The fixes address global persistent flush (GPF) changes and CXL
Features support changes that went in the 6.15 merge window. And also
a fix to an issue observed on CXL 1.1 platform during device
enumeration.
Summary:
- Fix using the wrong GPF DVSEC location:
- Fix caching of dport GPF DVSEC from the first endpoint
- Ensure that the GPF phase timeout is only updated once by first
endpoint
- Drop is_port parameter for cxl_gpf_get_dvsec()
- Fix the devm_* call host device for CXL fwctl setup
- Set the out_len in Set Features failure case
- Fix RCD initialization by skipping unneeded mem_en check"
* tag 'cxl-fixes-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/core/regs.c: Skip Memory Space Enable check for RCD and RCH Ports
cxl/feature: Update out_len in set feature failure case
cxl: Fix devm host device for CXL fwctl initialization
cxl/pci: Drop the parameter is_port of cxl_gpf_get_dvsec()
cxl/pci: Update Port GPF timeout only when the first EP attaching
cxl/core: Fix caching dport GPF DVSEC issue
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.15-2025-04-23:
amdgpu:
- P2P DMA fixes
- Display reset fixes
- DCN 3.5 fixes
- ACPI EDID fix
- LTTPR fix
- mode_valid() fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250423183045.2886753-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Several fixups
- fix spelling error
- remove redundant error handling in exynos_drm_vidi.c module.
- marks struct decon_data as const in the exynos7_drm_decon driver since it is only read.
Cleanup
- Remove unnecessary checking in exynos_drm_drv.c module
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://lore.kernel.org/r/20250423143044.46165-1-inki.dae@samsung.com
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Short summary of fixes pull:
meson:
- Fix VCLK calculation
panel:
- jd9365a: Fix reset polarity
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250422151209.GA24823@2a02-2454-fd5e-fd00-5cc9-93f1-8e9a-df9b.dyn6.pyur.net
|
|
Merge series from Vishwaroop A <va@nvidia.com>:
This series introduces QSPI clock configuration and internal DMA
support for Quad SPI controller. The patches have been reorganized
for better logical flow and review comments from v2 have been addressed.
|
|
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Renesas MSIOF can work as both SPI and I2S.
Current Linux supports MSIOF-SPI. This patch-set adds new MSIOF-I2S.
Because it is using same HW-IP, we want to share same compatible for both
MSIOF-SPI/I2S case. MSIOF-I2S (Sound) will use Audio-Graph-Card/Card2 which
uses Of-Graph, but MSIOF-SPI is not use Of-Graph.
So, this patch-set assumes it was used as MSIOF-I2S if DT is using Of-Graph,
otherwise, it is MSIOF-SPI (This assumption will works if SPI *never*
use Of-Graph in the future).
One note so far is that it is using "spi@xxx" node name for both
MSIOF-SPI/I2S. DTC will automatically checks "spi@xxx" node as SPI device
which requests #address-cells/#size-cells. But is not needed for I2S.
So we will get warning about it on Sparrow Hawk which uses MSIOF-I2S.
We have no solution about it, so far.
Link: https://lore.kernel.org/r/87zfgi1a5a.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87h62vh5mj.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/875xjeb0wu.wl-kuninori.morimoto.gx@renesas.com
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Single fix for broken usage of 'multi-MIDR' infrastructure in PI
code, adding an open-coded erratum check for everyone's favorite
pile of sand: Cavium ThunderX
x86:
- Bugfixes from a planned posted interrupt rework
- Do not use kvm_rip_read() unconditionally to cater for guests with
inaccessible register state"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Do not use kvm_rip_read() unconditionally for KVM_PROFILING
KVM: x86: Do not use kvm_rip_read() unconditionally in KVM tracepoints
KVM: SVM: WARN if an invalid posted interrupt IRTE entry is added
iommu/amd: WARN if KVM attempts to set vCPU affinity without posted intrrupts
iommu/amd: Return an error if vCPU affinity is set for non-vCPU IRTE
KVM: x86: Take irqfds.lock when adding/deleting IRQ bypass producer
KVM: x86: Explicitly treat routing entry type changes as changes
KVM: x86: Reset IRTE to host control if *new* route isn't postable
KVM: SVM: Allocate IR data using atomic allocation
KVM: SVM: Don't update IRTEs if APICv/AVIC is disabled
KVM: arm64, x86: make kvm_arch_has_irq_bypass() inline
arm64: Rework checks for broken Cavium HW in the PI code
|
|
Pull block fixes from Jens Axboe:
- Fix autoloading of drivers from stat*(2)
- Fix losing read-ahead setting one suspend/resume, when a device is
re-probed.
- Fix race between setting the block size and page cache updates.
Includes a helper that a coming XFS fix will use as well.
- ublk cancelation fixes.
- ublk selftest additions and fixes.
- NVMe pull via Christoph:
- fix an out-of-bounds access in nvmet_enable_port (Richard
Weinberger)
* tag 'block-6.15-20250424' of git://git.kernel.dk/linux:
ublk: fix race between io_uring_cmd_complete_in_task and ublk_cancel_cmd
ublk: call ublk_dispatch_req() for handling UBLK_U_IO_NEED_GET_DATA
block: don't autoload drivers on blk-cgroup configuration
block: don't autoload drivers on stat
block: remove the backing_inode variable in bdev_statx
block: move blkdev_{get,put} _no_open prototypes out of blkdev.h
block: never reduce ra_pages in blk_apply_bdi_limits
selftests: ublk: common: fix _get_disk_dev_t for pre-9.0 coreutils
selftests: ublk: remove useless 'delay_us' from 'struct dev_ctx'
selftests: ublk: fix recover test
block: hoist block size validation code to a separate function
block: fix race between set_blocksize and read paths
nvmet: fix out-of-bounds access in nvmet_enable_port
|
|
The 'wlen' member of the qpic_spi_nand structure is never used in the
code so remove that.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250424-qpic-snand-remove-wlen-v1-1-2a7467ce2e3a@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These are cpufreq driver fixes addressing multiple assorted issues:
- Fix possible out-of-bound / NULL-ptr-deref in cpufreq drivers
(Henry Martin, Andre Przywara)
- Fix Kconfig issues with compile-test in cpufreq drivers (Krzysztof
Kozlowski, Johan Hovold)
- Fix invalid return value in .get() in the CPPC cpufreq driver (Marc
Zyngier)
- Add SM8650 to cpufreq-dt-platdev blocklist (Pengyu Luo)"
* tag 'pm-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: fix compile-test defaults
cpufreq: cppc: Fix invalid return value in .get() callback
cpufreq: scpi: Fix null-ptr-deref in scpi_cpufreq_get_rate()
cpufreq: scmi: Fix null-ptr-deref in scmi_cpufreq_get_rate()
cpufreq: apple-soc: Fix null-ptr-deref in apple_soc_cpufreq_get_rate()
cpufreq: Do not enable by default during compile testing
cpufreq: Add SM8650 to cpufreq-dt-platdev blocklist
cpufreq: sun50i: prevent out-of-bounds access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 6.15-rc4.
Nothing major in here, just the normal set of issues that have cropped
up after -rc1:
- new device ids for usb-serial drivers
- new device quirks added
- typec driver fixes
- chipidea driver fixes
- xhci driver fixes
- wdm driver fixes
- cdns3 driver fixes
- MAINTAINERS file update
All of these, except for the MAINTAINERS file update, have been in
linux-next for a while with no reported issues"
* tag 'usb-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
MAINTAINERS: Assign maintainer for the port controller drivers
USB: serial: simple: add OWON HDS200 series oscilloscope support
USB: serial: ftdi_sio: add support for Abacus Electrics Optical Probe
USB: serial: option: add Sierra Wireless EM9291
usb: typec: class: Unlocked on error in typec_register_partner()
usb: quirks: Add delay init quirk for SanDisk 3.2Gen1 Flash Drive
USB: wdm: add annotation
USB: wdm: wdm_wwan_port_tx_complete mutex in atomic context
USB: wdm: close race between wdm_open and wdm_wwan_port_stop
USB: wdm: handle IO errors in wdm_wwan_port_start
USB: VLI disk crashes if LPM is used
usb: dwc3: gadget: check that event count does not exceed event buffer length
USB: storage: quirk for ADATA Portable HDD CH94
usb: quirks: add DELAY_INIT quirk for Silicon Motion Flash Drive
USB: OHCI: Add quirk for LS7A OHCI controller (rev 0x02)
usb: dwc3: xilinx: Prevent spike in reset signal
usb: cdns3: Fix deadlock when using NCM gadget
usb: chipidea: ci_hdrc_imx: implement usb_phy_init() error handling
usb: chipidea: ci_hdrc_imx: fix call balance of regulator routines
usb: chipidea: ci_hdrc_imx: fix usbmisc handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small tty/serial driver fixes for 6.15-rc4 to resolve
some reported issues. They are:
- permissions change for TIOCL_SELMOUSEREPORT to resolve a relaxing
of permissions that showed up 6.14 that wasn't _quite_ right.
- sifive serial driver fix
- msm serial driver fix
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sifive: lock port in startup()/shutdown() callbacks
tty: Require CAP_SYS_ADMIN for all usages of TIOCL_SELMOUSEREPORT
serial: msm: Configure correct working mode before starting earlycon
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes to resolve reported
problems for 6.15-rc4. Included in here are:
- misc chrdev region range fix reported by many people
- nvmem driver fixes and dt updates
- mei new device id and fixes
- comedi driver fix
- pps driver fix
- binder debug log fix
- pci1xxxx driver fixes
- firmware driver fix
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (25 commits)
firmware: stratix10-svc: Add of_platform_default_populate()
mei: vsc: Use struct vsc_tp_packet as vsc-tp tx_buf and rx_buf type
mei: vsc: Fix fortify-panic caused by invalid counted_by() use
pps: generators: tio: fix platform_set_drvdata()
mcb: fix a double free bug in chameleon_parse_gdd()
misc: microchip: pci1xxxx: Fix incorrect IRQ status handling during ack
misc: microchip: pci1xxxx: Fix Kernel panic during IRQ handler registration
char: misc: register chrdev region with all possible minors
mei: me: add panther lake H DID
comedi: jr3_pci: Fix synchronous deletion of timer
binder: fix offset calculation in debug log
intel_th: avoid using deprecated page->mapping, index fields
dt-bindings: nvmem: Add compatible for MSM8960
dt-bindings: nvmem: Add compatible for IPQ5018
nvmem: qfprom: switch to 4-byte aligned reads
nvmem: core: update raw_len if the bit reading is required
nvmem: core: verify cell's raw_len
nvmem: core: fix bit offsets of more than one byte
dt-bindings: nvmem: fixed-cell: increase bits start value to 31
dt-bindings: nvmem: Add compatible for MS8937
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core fixes to resolve a number of reported
problems. Included in here are:
- driver core sync fix revert to resolve a much reported problem,
hopefully this is finally resolved
- MAINTAINERS file update, documenting that the driver-core tree is
now under a "shared" maintainership model, thanks to Rafael and
Danilo for offering to do this!
- auxbus documentation and MAINTAINERS file update
- MAINTAINERS file update for Rust PCI code
- firmware rust binding fixup
- software node link fix
All of these have been in linux-next for over a week with no reported
issues"
* tag 'driver-core-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
drivers/base/memory: Avoid overhead from for_each_present_section_nr()
software node: Prevent link creation failure from causing kobj reference count imbalance
device property: Add a note to the fwnode.h
drivers/base: Add myself as auxiliary bus reviewer
drivers/base: Extend documentation with preferred way to use auxbus
driver core: fix potential NULL pointer dereference in dev_uevent()
driver core: introduce device_set_driver() helper
Revert "drivers: core: synchronize really_probe() and dev_uevent()"
MAINTAINERS: update the location of the driver-core git tree
rust: firmware: Use `ffi::c_char` type in `FwFunc`
MAINTAINERS: pci: add entry for Rust PCI code
|
|
The recent move of the bdev_statx call to the low-level vfs_getattr_nosec
helper caused it being used by devtmpfs, which leads to deadlocks in
md teardown due to the block device lookup and put interfering with the
unusual lifetime rules in md.
But as handle_remove only works on inodes created and owned by devtmpfs
itself there is no need to use vfs_getattr_nosec vs simply reading the
mode from the inode directly. Switch to that to avoid the bdev lookup
or any other unintentional side effect.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reported-by: Xiao Ni <xni@redhat.com>
Fixes: 777d0961ff95 ("fs: move the bdex_statx call to vfs_getattr_nosec")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/20250423045941.1667425-1-hch@lst.de
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Xiao Ni <xni@redhat.com>
Tested-by: Ayush Jain <Ayush.jain3@amd.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
ublk_cancel_cmd() calls io_uring_cmd_done() to complete uring_cmd, but
we may have scheduled task work via io_uring_cmd_complete_in_task() for
dispatching request, then kernel crash can be triggered.
Fix it by not trying to canceling the command if ublk block request is
started.
Fixes: 216c8f5ef0f2 ("ublk: replace monitor with cancelable uring_cmd")
Reported-by: Jared Holzman <jholzman@nvidia.com>
Tested-by: Jared Holzman <jholzman@nvidia.com>
Closes: https://lore.kernel.org/linux-block/d2179120-171b-47ba-b664-23242981ef19@nvidia.com/
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250425013742.1079549-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We call io_uring_cmd_complete_in_task() to schedule task_work for handling
UBLK_U_IO_NEED_GET_DATA.
This way is really not necessary because the current context is exactly
the ublk queue context, so call ublk_dispatch_req() directly for handling
UBLK_U_IO_NEED_GET_DATA.
Fixes: 216c8f5ef0f2 ("ublk: replace monitor with cancelable uring_cmd")
Tested-by: Jared Holzman <jholzman@nvidia.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250425013742.1079549-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The single core change is an obvious bug fix (and falls within the LF
guidelines for patches from sanctioned entities). The other driver
changes are a bit larger but likewise pretty obvious"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Add level check to control event logging
scsi: ufs: core: Add NULL check in ufshcd_mcq_compl_pending_transfer()
scsi: core: Clear flags for scsi_cmnd that did not complete
scsi: ufs: Introduce quirk to extend PA_HIBERN8TIME for UFS devices
scsi: ufs: qcom: Add quirks for Samsung UFS devices
scsi: target: iscsi: Fix timeout on deleted connection
scsi: mpi3mr: Reset the pending interrupt flag
scsi: mpi3mr: Fix pending I/O counter
scsi: ufs: mcq: Add NULL check in ufshcd_mcq_abort()
|
|
Add DMA support for spicc driver.
DMA works if the transfer meets the following conditions:
1. 64 bits per word;
2. The transfer length must be multiples of the dma_burst_len,
and the dma_burst_len should be one of 8,7...2,
otherwise, it will be split into several SPI bursts.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://patch.msgid.link/20250414-spi-dma-v2-1-84bbd92fa469@amlogic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"No fixes from any subtree.
Current release - regressions:
- net: fix the missing unlock for detached devices
Previous releases - regressions:
- sched: fix UAF vulnerability in HFSC qdisc
- lwtunnel: disable BHs when required
- mptcp: pm: defer freeing of MPTCP userspace path manager entries
- tipc: fix NULL pointer dereference in tipc_mon_reinit_self()
- eth: virtio-net: disable delayed refill when pausing rx
Previous releases - always broken:
- phylink: fix suspend/resume with WoL enabled and link down
- eth:
- mlx5: fix null-ptr-deref in mlx5_create_{inner_,}ttc_table()
- xen-netfront: handle NULL returned by xdp_convert_buff_to_frame()
- enetc: fix frame corruption on bpf_xdp_adjust_head/tail() and XDP_PASS
- stmmac: fix dwmac1000 ptp timestamp status offset
- pds_core: prevent possible adminq overflow/stuck condition
Misc:
- a bunch of MAINTAINERS updates"
* tag 'net-6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (32 commits)
net: stmmac: fix multiplication overflow when reading timestamp
net: stmmac: fix dwmac1000 ptp timestamp status offset
net: dp83822: Fix OF_MDIO config check
pds_core: make wait_context part of q_info
pds_core: Remove unnecessary check in pds_client_adminq_cmd()
pds_core: handle unsupported PDS_CORE_CMD_FW_CONTROL result
pds_core: Prevent possible adminq overflow/stuck condition
net: dsa: mt7530: sync driver-specific behavior of MT7531 variants
selftests/tc-testing: Add test for HFSC queue emptying during peek operation
net_sched: hfsc: Fix a potential UAF in hfsc_dequeue() too
net_sched: hfsc: Fix a UAF vulnerability in class handling
selftests: mptcp: diag: use mptcp_lib_get_info_value
mptcp: pm: Defer freeing of MPTCP userspace path manager entries
net: ethernet: mtk_eth_soc: net: revise NETSYSv3 hardware configuration
tipc: fix NULL pointer dereference in tipc_mon_reinit_self()
virtio-net: disable delayed refill when pausing rx
net: phy: leds: fix memory leak
net: phylink: mac_link_(up|down)() clarifications
net: phylink: fix suspend/resume with WoL enabled and link down
net: lwtunnel: disable BHs when required
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Revert acomp multibuffer tests which were buggy
- Fix off-by-one regression in new scomp code
- Lower quality setting on atmel-sha204a as it may not be random
* tag 'v6.15-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: atmel-sha204a - Set hwrng quality to lowest possible
crypto: scomp - Fix off-by-one bug when calculating last page
Revert "crypto: testmgr - Add multibuffer acomp testing"
|
|
WARN if KVM attempts to set vCPU affinity when posted interrupts aren't
enabled, as KVM shouldn't try to enable posting when they're unsupported,
and the IOMMU driver darn well should only advertise posting support when
AMD_IOMMU_GUEST_IR_VAPIC() is true.
Note, KVM consumes is_guest_mode only on success.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Return -EINVAL instead of success if amd_ir_set_vcpu_affinity() is
invoked without use_vapic; lying to KVM about whether or not the IRTE was
configured to post IRQs is all kinds of bad.
Fixes: d98de49a53e4 ("iommu/amd: Enable vAPIC interrupt remapping mode by default")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Adding support for the dummy sequence configuration. The dummy sequence
introduces a delay between the command and the data phases of a
transfer. This delay, measured in clock cycles, allows the slave
device to prepare for data transmission, ensuring data integrity and
proper synchronization.
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-6-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Modify the chip select (CS) deactivation and inter-transfer delay
execution only during the DATA_TRANSFER phase when the cs_change
flag is not set. This ensures proper CS handling and timing between
transfers while eliminating redundant operations.
Fixes: 1b8342cc4a38 ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-4-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove unnecessary error handling code that terminated transfers and
executed delay on errors. This code was redundant as error handling is
already done at a higher level in the SPI core.
Fixes: 1b8342cc4a38 ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-3-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch corrects the QSPI_COMMAND_X1_X2_X4 and QSPI_ADDRESS_X1_X2_X4
macros to properly encode the bus width for x1, x2, and x4 transfers.
Although these macros were previously incorrect, they were not being
used in the driver, so no functionality was affected.
The patch updates tegra_qspi_cmd_config() and tegra_qspi_addr_config()
function calls to use the actual bus width from the transfer, instead of
hardcoding it to 0 (which implied x1 mode). This change enables proper
support for x1, x2, and x4 data transfers by correctly configuring the
interface width for commands and addresses.
These modifications improve the QSPI driver's flexibility and prepare it
for future use cases that may require different bus widths for commands
and addresses.
Fixes: 1b8342cc4a38 ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20250416110606.2737315-2-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let's use the pci/platform-specialized functions for mapping a resource,
and pass the mapped address to intel_spi_probe. Benefits are:
- No separate call needed for getting the resource, and no access to
struct pci_dev internals (pdev->resource[]).
- More user-friendly output in /proc/iomem. In my case:
before
80704000-80704fff : 0000:00:1f.5
80704000-80704fff : 0000:00:1f.5 0000:00:1f.5
after
80704000-80704fff : 0000:00:1f.5
80704000-80704fff : spi_intel_pci
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/2585fa05-60c4-48c4-a838-e87014665ae2@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Renesas MSIOF (Clock-Synchronized Serial Interface with FIFO) can work as
both SPI and I2S. MSIOF-I2S will use Audio Graph Card/Card2 driver which
Of-Graph in DT.
MSIOF-SPI/I2S are using same DT compatible properties.
MSIOF-I2S uses Of-Graph for Audio-Graph-Card/Card2,
MSIOF-SPI doesn't use Of-Graph.
Check "port" node when driver probing
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/87wmbi2x0g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sh_msiof_spi_probe() is using priv->dev everywhere,
but it makes code long. Create struct device *dev and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/87y0vy2x0o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current way of reading a timestamp snapshot in stmmac can lead to
integer overflow, as the computation is done on 32 bits. The issue has
been observed on a dwmac-socfpga platform returning chaotic timestamp
values due to this overflow. The corresponding multiplication is done
with a MUL instruction, which returns 32 bit values. Explicitly casting
the value to 64 bits replaced the MUL with a UMLAL, which computes and
returns the result on 64 bits, and so returns correctly the timestamps.
Prevent this overflow by explicitly casting the intermediate value to
u64 to make sure that the whole computation is made on u64. While at it,
apply the same cast on the other dwmac variant (GMAC4) method for
snapshot retrieval.
Fixes: 477c3e1f6363 ("net: stmmac: Introduce dwmac1000 timestamping operations")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250423-stmmac_ts-v2-2-e2cf2bbd61b1@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a PTP interrupt occurs, the driver accesses the wrong offset to
learn about the number of available snapshots in the FIFO for dwmac1000:
it should be accessing bits 29..25, while it is currently reading bits
19..16 (those are bits about the auxiliary triggers which have generated
the timestamps). As a consequence, it does not compute correctly the
number of available snapshots, and so possibly do not generate the
corresponding clock events if the bogus value ends up being 0.
Fix clock events generation by reading the correct bits in the timestamp
register for dwmac1000.
Fixes: 477c3e1f6363 ("net: stmmac: Introduce dwmac1000 timestamping operations")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250423-stmmac_ts-v2-1-e2cf2bbd61b1@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 5dc39fd5ef35 ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250423044724.1284492-1-johannes.schneider@leica-geosystems.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make the wait_context a full part of the q_info struct rather
than a stack variable that goes away after pdsc_adminq_post()
is done so that the context is still available after the wait
loop has given up.
There was a case where a slow development firmware caused
the adminq request to time out, but then later the FW finally
finished the request and sent the interrupt. The handler tried
to complete_all() the completion context that had been created
on the stack in pdsc_adminq_post() but no longer existed.
This caused bad pointer usage, kernel crashes, and much wailing
and gnashing of teeth.
Fixes: 01ba61b55b20 ("pds_core: Add adminq processing and commands")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250421174606.3892-5-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the pds_core driver was first created there were some race
conditions around using the adminq, especially for client drivers.
To reduce the possibility of a race condition there's a check
against pf->state in pds_client_adminq_cmd(). This is problematic
for a couple of reasons:
1. The PDSC_S_INITING_DRIVER bit is set during probe, but not
cleared until after everything in probe is complete, which
includes creating the auxiliary devices. For pds_fwctl this
means it can't make any adminq commands until after pds_core's
probe is complete even though the adminq is fully up by the
time pds_fwctl's auxiliary device is created.
2. The race conditions around using the adminq have been fixed
and this path is already protected against client drivers
calling pds_client_adminq_cmd() if the adminq isn't ready,
i.e. see pdsc_adminq_post() -> pdsc_adminq_inc_if_up().
Fix this by removing the pf->state check in pds_client_adminq_cmd()
because invalid accesses to pds_core's adminq is already handled by
pdsc_adminq_post()->pdsc_adminq_inc_if_up().
Fixes: 10659034c622 ("pds_core: add the aux client API")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250421174606.3892-4-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the FW doesn't support the PDS_CORE_CMD_FW_CONTROL command
the driver might at the least print garbage and at the worst
crash when the user runs the "devlink dev info" devlink command.
This happens because the stack variable fw_list is not 0
initialized which results in fw_list.num_fw_slots being a
garbage value from the stack. Then the driver tries to access
fw_list.fw_names[i] with i >= ARRAY_SIZE and runs off the end
of the array.
Fix this by initializing the fw_list and by not failing
completely if the devcmd fails because other useful information
is printed via devlink dev info even if the devcmd fails.
Fixes: 45d76f492938 ("pds_core: set up device and adminq")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250421174606.3892-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
