| Age | Commit message (Collapse) | Author |
|---|
|
The same fix that was previously done in m_can_platform in commit
99d173fbe894 ("can: m_can: fix iomap_read_fifo() and iomap_write_fifo()")
is required in m_can_pci as well to make iomap_read_fifo() and
iomap_write_fifo() work for val_count > 1.
Fixes: 812270e5445b ("can: m_can: Batch FIFO writes during CAN transmit")
Fixes: 1aa6772f64b4 ("can: m_can: Batch FIFO reads during CAN receive")
Link: https://lore.kernel.org/all/20211118144011.10921-1-matthias.schiffer@ew.tq-group.com
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In m_can_read_fifo(), if the second call to m_can_fifo_read() fails,
the function jump to the out_fail label and returns without calling
m_can_receive_skb(). This means that the skb previously allocated by
alloc_can_skb() is not freed. In other terms, this is a memory leak.
This patch adds a goto label to destroy the skb if an error occurs.
Issue was found with GCC -fanalyzer, please follow the link below for
details.
Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20211107050755.70655-1-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With the design of this driver, this condition is often triggered.
However, the counter that this interrupt indicates an overflow is never
read either, so overflowing is harmless.
On my system, when a CAN bus starts flapping up and down, this locks up
the whole system with lots of interrupts and printks.
Specifically, this interrupt indicates the CEL field of ECR has
overflowed. All reads of ECR mask out CEL.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/all/20211129222628.7490-1-brian.silverman@bluerivertech.com
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the last channel is not available then "dev" is freed. Fortunately,
we can just use "pdev->irq" instead.
Also we should check if at least one channel was set up.
Fixes: fd734c6f25ae ("can/sja1000: add driver for EMS PCMCIA card")
Link: https://lore.kernel.org/all/20211124145041.GB13656@kili
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
After calling netif_receive_skb(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is dereferenced
just after the call netif_receive_skb(skb).
Reordering the lines solves the issue.
Fixes: b21d18b51b31 ("can: Topcliff: Add PCH_CAN driver.")
Link: https://lore.kernel.org/all/20211123111654.621610-1-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.
Enable the deferred probe quirk for the UM325UA.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211204015615.232948-1-samuel@cavoj.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 598a90f2002c ("scsi: qla2xxx: add ring buffer for tracing debug
logs") introduced unconditional log string formatting to ql_dbg() even if
ql_dbg_log event is disabled. It harms performance because some strings are
formatted in fastpath and/or interrupt context.
Link: https://lore.kernel.org/r/20211112145446.51210-1-r.bolshakov@yadro.com
Fixes: 598a90f2002c ("scsi: qla2xxx: add ring buffer for tracing debug logs")
Cc: Rajan Shanmugavelu <rajan.shanmugavelu@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com
Fixes: f0d1cf9378bd ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When issued LUN reset under heavy I/O we hit the qedi WARN_ON because of a
mismatch in firmware I/O cmd cleanup request count and I/O cmd cleanup
response count received. The mismatch is because of a race caused by the
postfix increment of cmd_cleanup_cmpl.
[qedi_clearsq:1295]:18: fatal error, need hard reset, cid=0x0
WARNING: CPU: 48 PID: 110963 at drivers/scsi/qedi/qedi_fw.c:1296 qedi_clearsq+0xa5/0xd0 [qedi]
CPU: 48 PID: 110963 Comm: kworker/u130:0 Kdump: loaded Tainted: G W
Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 04/15/2020
Workqueue: iscsi_conn_cleanup iscsi_cleanup_conn_work_fn [scsi_transport_iscsi]
RIP: 0010:qedi_clearsq+0xa5/0xd0 [qedi]
RSP: 0018:ffffac2162c7fd98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff975213c40ab8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9761bf816858 RDI: ffff9761bf816858
RBP: ffff975247018628 R08: 000000000000522c R09: 000000000000005b
R10: 0000000000000000 R11: ffffac2162c7fbd8 R12: ffff97522e1b2be8
R13: 0000000000000000 R14: ffff97522e1b2800 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff9761bf800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1a34e3e1a0 CR3: 0000000108bb2000 CR4: 0000000000350ee0
Call Trace:
qedi_ep_disconnect+0x533/0x550 [qedi]
? iscsi_dbg_trace+0x63/0x80 [scsi_transport_iscsi]
? _cond_resched+0x15/0x30
? iscsi_suspend_queue+0x19/0x40 [libiscsi]
iscsi_ep_disconnect+0xb0/0x130 [scsi_transport_iscsi]
iscsi_cleanup_conn_work_fn+0x82/0x130 [scsi_transport_iscsi]
process_one_work+0x1a7/0x360
? create_worker+0x1a0/0x1a0
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x116/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x22/0x40
---[ end trace 5f1441f59082235c ]---
Link: https://lore.kernel.org/r/20211203095218.5477-1-mrangankar@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Without this change eMMC runs at overclocked freq.
Swap the ops to not OC the eMMC.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Link: https://lore.kernel.org/r/20211130212015.25232-1-martin.botka@somainline.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 4b8d6ae57cdf ("clk: qcom: Add SM6125 (TRINKET) GCC driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Similar to other systems Surface Go 3 requires a DMI quirk to enable
5 button array for power and volume buttons.
Buglink: https://github.com/linux-surface/linux-surface/issues/595
Cc: stable@vger.kernel.org
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Link: https://lore.kernel.org/r/20211203212810.2666508-1-alex.hung@canonical.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
Fixes: 02e9c290814c ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc280473 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
mtdblock / mtdblock_ro set part_bits to 0 and thus nevever scanned
partitions. Restore that behavior by setting the GENHD_FL_NO_PART flag.
Fixes: 1ebe2e5f9d68e94c ("block: remove GENHD_FL_EXT_DEVT")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211206070409.2836165-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef253 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The write pointer in NVMe ZNS is invalid for a zone in zone state full.
The same also holds true for ZAC/ZBC.
The current behavior for NVMe is to simply propagate the wp reported by
the drive, even for full zones. Since the wp is invalid for a full zone,
the wp reported by the drive may be any value.
The way that the sd_zbc driver handles a full zone is to always report
the wp as zone start + zone len, regardless of what the drive reported.
null_blk also follows this convention.
Do the same for NVMe, so that a BLKREPORTZONE ioctl reports the write
pointer for a full zone in a consistent way, regardless of the interface
of the underlying zoned block device.
blkzone report before patch:
start: 0x000040000, len 0x040000, cap 0x03e000, wptr 0xfffffffffffbfff8
reset:0 non-seq:0, zcond:14(fu) [type: 2(SEQ_WRITE_REQUIRED)]
blkzone report after patch:
start: 0x000040000, len 0x040000, cap 0x03e000, wptr 0x040000 reset:0
non-seq:0, zcond:14(fu) [type: 2(SEQ_WRITE_REQUIRED)]
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The only fabrics target that supports metadata handling through the
separate integrity buffer is RDMA. It is currently usable only if the
size is 8B per block and formatted for protection information. If an
rdma target were to export a namespace with a different format (ex:
4k+64B), the driver will not be able to submit valid read/write commands
for that namespace.
Suppress setting the metadata feature in the namespace so that the
gendisk capacity will be set to 0. This will prevent read/write access
through the block stack, but will continue to allow ioctl passthrough
commands.
Cc: Max Gurtovoy <mgurtovoy@nvidia.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The driver assigned nvme handle isn't persistent across reboots, so is
not enough information to match up where the collisions are occuring.
Add the subsys nqn string to the output so that it can more easily be
identified later.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215099
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Most of the blk-ctrl reset bits are found in one register, however
there are two bits in offset 8 for pulling the MIPI DPHY out of reset
and one of them needs to be set when IMX8MM_DISPBLK_PD_MIPI_CSI is brought
out of reset or the MIPI_CSI hangs.
Since MIPI_DSI is impacted, add the additional one for MIPI_DSI too.
Fixes: 926e57c065df ("soc: imx: imx8m-blk-ctrl: add DISP blk-ctrl")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ATA IDENTIFY command returns an array of le16 words. Accessing it as a
u16 array triggers the following sparse warning:
drivers/ata/ahci_ceva.c:107:33: warning: invalid assignment: &=
drivers/ata/ahci_ceva.c:107:33: left side has type unsigned short
drivers/ata/ahci_ceva.c:107:33: right side has type restricted __le16
Use a local variable to explicitly cast the id array to __le16 to avoid
this warning.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Some bug and warning fixes:
- Fix "make install" to use debians "installkernel" script which is
now in /usr/sbin
- Fix the bindeb-pkg make target by giving the correct KBUILD_IMAGE
file name
- Fix compiler warnings by annotating parisc agp init functions with
__init
- Fix timekeeping on SMP machines with dual-core CPUs
- Enable some more config options in the 64-bit defconfig"
* tag 'for-5.16/parisc-6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Mark cr16 CPU clocksource unstable on all SMP machines
parisc: Fix "make install" on newer debian releases
parisc/agp: Annotate parisc agp init functions with __init
parisc: Enable sata sil, audit and usb support on 64-bit defconfig
parisc: Fix KBUILD_IMAGE for self-extracting kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for a few reported issues. Included in
here are:
- xhci fix for a _much_ reported regression. I don't think there's a
community distro that has not reported this problem yet :(
- new USB quirk addition
- cdns3 minor fixes
- typec regression fix.
All of these have been in linux-next with no reported problems, and
the xhci fix has been reported by many to resolve their reported
problem"
* tag 'usb-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()
usb: cdns3: gadget: fix new urb never complete if ep cancel previous requests
usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnect
USB: NO_LPM quirk Lenovo Powered USB-C Travel Hub
xhci: Fix commad ring abort, write all 64 bits to CRCR register.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes for 5.16-rc4 to
resolve a number of reported problems.
They include:
- liteuart serial driver fixes
- 8250_pci serial driver fixes for pericom devices
- 8250 RTS line control fix while in RS-485 mode
- tegra serial driver fix
- msm_serial driver fix
- pl011 serial driver new id
- fsl_lpuart revert of broken change
- 8250_bcm7271 serial driver fix
- MAINTAINERS file update for rpmsg tty driver that came in 5.16-rc1
- vgacon fix for reported problem
All of these, except for the 8250_bcm7271 fix have been in linux-next
with no reported problem. The 8250_bcm7271 fix was added to the tree
on Friday so no chance to be linux-next yet. But it should be fine as
the affected developers submitted it"
* tag 'tty-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_bcm7271: UART errors after resuming from S2
serial: 8250_pci: rewrite pericom_do_set_divisor()
serial: 8250_pci: Fix ACCES entries in pci_serial_quirks array
serial: 8250: Fix RTS modem control while in rs485 mode
Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"
serial: tegra: Change lower tolerance baud rate limit for tegra20 and tegra30
serial: liteuart: relax compile-test dependencies
serial: liteuart: fix minor-number leak on probe errors
serial: liteuart: fix use-after-free and memleak on unbind
serial: liteuart: Fix NULL pointer dereference in ->remove()
vgacon: Propagate console boot parameters before calling `vc_resize'
tty: serial: msm_serial: Deactivate RX DMA for polling support
serial: pl011: Add ACPI SBSA UART match id
serial: core: fix transmit-buffer reset and memleak
MAINTAINERS: Add rpmsg tty driver maintainer
|
|
Pull block fix from Jens Axboe:
"A single fix for repeated printk spam from loop"
* tag 'block-5.16-2021-12-03' of git://git.kernel.dk/linux-block:
loop: Use pr_warn_once() for loop_control_remove() warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches, both in drivers.
One is a fix to FC recovery (lpfc) and the other is an enhancement to
support the Intel Alder Motherboard with the UFS driver which comes
under the -rc exception process for hardware enabling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-pci: Add support for Intel ADL
scsi: lpfc: Fix non-recovery of remote ports following an unsolicited LOGO
|
|
modprobe can't handle spaces in aliases.
Fixes: 93fbe91b5521 ("iio: Add STM32 timer trigger driver")
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Link: https://lore.kernel.org/r/20211125182850.2645424-1-hi@alyssa.is
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d3364f9 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
Fixes: a2ec6172d29c ("qede: Add support for link")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20211203174413.13090-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull VFIO fixes from Alex Williamson:
- Fix OpRegion pointer arithmetic (Zhenyu Wang)
- Fix comment format triggering kernel-doc warnings (Randy Dunlap)
* tag 'vfio-v5.16-rc4' of git://github.com/awilliam/linux-vfio:
vfio/pci: Fix OpRegion read
vfio: remove all kernel-doc notation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a CPU hot-add issue in the cpufreq core, fix a comment in
the cpufreq core code and update its documentation, and disable the
DTPM (Dynamic Thermal Power Management) code for the time being to
prevent it from causing issues to appear.
Specifics:
- Disable DTPM for this cycle to prevent it from causing issues to
appear on otherwise functional systems (Daniel Lezcano)
- Fix cpufreq sysfs interface failure related to physical CPU hot-add
(Xiongfeng Wang)
- Fix comment in cpufreq core and update its documentation (Tang
Yizhou)"
* tag 'pm-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: DTPM: Drop unused local variable from init_dtpm()
cpufreq: docs: Update core.rst
cpufreq: Fix a comment in cpufreq_policy_free
powercap/drivers/dtpm: Disable DTPM at boot time
cpufreq: Fix get_cpu_device() failure in add_cpu_dev_symlink()
|
|
cgroup.h (therefore swap.h, therefore half of the universe)
includes bpf.h which in turn includes module.h and slab.h.
Since we're about to get rid of that dependency we need
to clean things up.
v2: drop the cpu.h include from cacheinfo.h, it's not necessary
and it makes riscv sensitive to ordering of include files.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20211120035253.72074-1-kuba@kernel.org/ # v1
Link: https://lore.kernel.org/all/20211120165528.197359-1-kuba@kernel.org/ # cacheinfo discussion
Link: https://lore.kernel.org/bpf/20211202203400.1208663-1-kuba@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has another set of driver bugfixes, mostly for the stm32f7 driver"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Handle a spurious start completion interrupt flag
i2c: stm32f7: use proper DMAENGINE API for termination
i2c: stm32f7: stop dma transfer in case of NACK
i2c: stm32f7: recover the bus on access timeout
i2c: stm32f7: flush TX FIFO upon transfer errors
i2c: cbus-gpio: set atomic transfer callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull libata fixes from Damien Le Moal:
"Two sparse warning fixes and a couple of patches to fix an issue with
sata_fsl driver module removal:
- A couple of patches to avoid sparse warnings in libata-sata and in
the pata_falcon driver (from Yang and Finn).
- A couple of sata_fsl driver patches fixing IRQ free and proc
unregister on module removal (from Baokun)"
* tag 'libata-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: replace snprintf in show functions with sysfs_emit
sata_fsl: fix warning in remove_proc_entry when rmmod sata_fsl
sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl
pata_falcon: Avoid type warnings from sparse
|
|
Since commit 041284181226 ("of/irq: Allow matching of an interrupt-map
local to an interrupt controller"), a handful of interrupt controllers
have stopped working correctly. This is due to the DT exposing a
non-sensical interrupt-map property, and their drivers relying on the
kernel ignoring this property.
Since we cannot realistically fix this terrible behaviour, add a quirk
for the limited set of devices that have implemented this monster,
and document that this is a pretty bad practice.
Fixes: 041284181226 ("of/irq: Allow matching of an interrupt-map local to an interrupt controller")
Cc: Rob Herring <robh@kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211201114102.13446-1-maz@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Merge DTPM fixes for 5.16-rc4.
* powercap:
powercap: DTPM: Drop unused local variable from init_dtpm()
powercap/drivers/dtpm: Disable DTPM at boot time
|
|
The dtpm_descr variable in init_dtpm() is not used after commit
f751db8adaea ("powercap/drivers/dtpm: Disable DTPM at boot time"),
so drop it.
Fixes: f751db8adaea ("powercap/drivers/dtpm: Disable DTPM at boot time")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value of dma_set_coherent_mask() is not always 0.
To catch the exception in case that dma is not support the mask.
Fixes: 9d61d138ab30 ("net: broadcom: rename BCM4908 driver & update DT binding")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KCSAN reported a data-race [1] around tx_rebalance_counter
which can be accessed from different contexts, without
the protection of a lock/mutex.
[1]
BUG: KCSAN: data-race in bond_alb_init_slave / bond_alb_monitor
write to 0xffff888157e8ca24 of 4 bytes by task 7075 on cpu 0:
bond_alb_init_slave+0x713/0x860 drivers/net/bonding/bond_alb.c:1613
bond_enslave+0xd94/0x3010 drivers/net/bonding/bond_main.c:1949
do_set_master net/core/rtnetlink.c:2521 [inline]
__rtnl_newlink net/core/rtnetlink.c:3475 [inline]
rtnl_newlink+0x1298/0x13b0 net/core/rtnetlink.c:3506
rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2491
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5589
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x5fc/0x6c0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x6e1/0x7d0 net/netlink/af_netlink.c:1916
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x195/0x230 net/socket.c:2492
__do_sys_sendmsg net/socket.c:2501 [inline]
__se_sys_sendmsg net/socket.c:2499 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2499
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888157e8ca24 of 4 bytes by task 1082 on cpu 1:
bond_alb_monitor+0x8f/0xc00 drivers/net/bonding/bond_alb.c:1511
process_one_work+0x3fc/0x980 kernel/workqueue.c:2298
worker_thread+0x616/0xa70 kernel/workqueue.c:2445
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x00000001 -> 0x00000064
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1082 Comm: kworker/u4:3 Not tainted 5.16.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: bond1 bond_alb_monitor
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_ids are
missing for the dataflash driver and the following warnings are now
seen.
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
Fix this by adding the necessary spi_device_ids.
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130112443.107730-1-jonathanh@nvidia.com
|
|
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571833 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
|
|
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
Fixes: 4da712e70294 ("mtd: nand: fsmc: use ->exec_op()")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-4-herve.codina@bootlin.com
|
|
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814e9 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
|
|
NAND_OP_CMD() expects a delay parameter in nanoseconds.
The delay value is wrongly given in milliseconds.
Fix the conversion macro used in order to set this
delay in nanoseconds.
Fixes: d7a773e8812b ("mtd: rawnand: Access SDR and NV-DDR timings through a common macro")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-2-herve.codina@bootlin.com
|
|
The helper function devm_platform_ioremap_resource_xxx()
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: 5f14a8ca1b49 ("mtd: rawnand: denali: Make use of the helper function devm_platform_ioremap_resource_byname()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211109134758.417-1-caihuoqing@baidu.com
|
|
After commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM"), when the
rtsx controller is runtime suspended, bring CPUs offline and back online, the
runtime resume of the controller will fail:
[ 47.319391] smpboot: CPU 1 is now offline
[ 47.414140] x86: Booting SMP configuration:
[ 47.414147] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 47.571334] smpboot: CPU 2 is now offline
[ 47.686055] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 47.808174] smpboot: CPU 3 is now offline
[ 47.878146] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 48.003679] smpboot: CPU 4 is now offline
[ 48.086187] smpboot: Booting Node 0 Processor 4 APIC 0x1
[ 48.239627] smpboot: CPU 5 is now offline
[ 48.326059] smpboot: Booting Node 0 Processor 5 APIC 0x3
[ 48.472193] smpboot: CPU 6 is now offline
[ 48.574181] smpboot: Booting Node 0 Processor 6 APIC 0x5
[ 48.743375] smpboot: CPU 7 is now offline
[ 48.838047] smpboot: Booting Node 0 Processor 7 APIC 0x7
[ 48.965447] __common_interrupt: 1.35 No irq handler for vector
[ 51.174065] mmc0: error -110 doing runtime resume
[ 54.978088] I/O error, dev mmcblk0, sector 21479 op 0x1:(WRITE) flags 0x0 phys_seg 11 prio class 0
[ 54.978108] Buffer I/O error on dev mmcblk0p1, logical block 19431, lost async page write
[ 54.978129] Buffer I/O error on dev mmcblk0p1, logical block 19432, lost async page write
[ 54.978134] Buffer I/O error on dev mmcblk0p1, logical block 19433, lost async page write
[ 54.978137] Buffer I/O error on dev mmcblk0p1, logical block 19434, lost async page write
[ 54.978141] Buffer I/O error on dev mmcblk0p1, logical block 19435, lost async page write
[ 54.978145] Buffer I/O error on dev mmcblk0p1, logical block 19436, lost async page write
[ 54.978148] Buffer I/O error on dev mmcblk0p1, logical block 19437, lost async page write
[ 54.978152] Buffer I/O error on dev mmcblk0p1, logical block 19438, lost async page write
[ 54.978155] Buffer I/O error on dev mmcblk0p1, logical block 19439, lost async page write
[ 54.978160] Buffer I/O error on dev mmcblk0p1, logical block 19440, lost async page write
[ 54.978244] mmc0: card aaaa removed
[ 54.978452] FAT-fs (mmcblk0p1): FAT read failed (blocknr 4257)
There's interrupt immediately raised on rtsx_pci_write_register() in
runtime resume routine, but the IRQ handler hasn't registered yet.
So we can either move rtsx_pci_write_register() after rtsx_pci_acquire_irq(),
or just stop mangling IRQ on runtime PM. Choose the latter to save some
CPU cycles.
Fixes: 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1951784
Link: https://lore.kernel.org/r/20211126003246.1068770-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
