| Age | Commit message (Collapse) | Author |
|---|
|
Add an mv88e6xxx_num_ports helper instead of digging in the chip info
structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx_num_databases will be used by shared code, so move it
inline to the header file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flags to describe the presence of Global 1 ATU FID register (0x01)
and VTU FID register (0x02), instead of checking families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to the ports, phys, and Global SMI devices, abstract the SMI
device address of the Global 2 registers in a few g2 static helpers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Global (1) internal SMI device is an extended set of registers
containing ATU, PPU, VTU, STU, etc.
It is present on every switches, usually at SMI address 0x1B. But old
models such as 88E6060 access it at address 0xF, thus using REG_GLOBAL
is erroneous.
Add a global1_addr info member used by mv88e6xxx_g1_{read,write} and
mv88e6xxx_g1_wait helpers in a new global1.c file.
This patch finally removes _mv88e6xxx_reg_{read,write}, in favor on the
appropriate helpers. No functional changes here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"drm fixes for final 4.8.
One big regression fix for udl, along with two amdgpu fixes and two
nouveau fixes.
All seems pretty safe and useful"
* tag 'drm-fixes-for-v4.8-final' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix line iterator in damage handling
drm/radeon/si/dpm: add workaround for for Jet parts
drm/amdgpu: disable CRTCs before teardown
drm/nouveau: Revert "bus: remove cpu_coherent flag"
drm/nouveau/fifo/nv04: avoid ramht race against cookie insertion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Four fixes for "flush hint" support.
Flush hints are addresses advertised by the ACPI 6+ NFIT (NVDIMM
Firmware Interface Table) that when written and fenced guarantee that
writes pending in platform write buffers (outside the cpu) have been
flushed to media. They might also be used by hypervisors as a
trigger condition to flush guest-persistent memory ranges to storage.
Fix a potential data corruption issue, a broken definition of the
hint array, a wrong allocation size for the unit test implementation
of the flush hint table, and missing NULL check in an error path.
The unit test, while it did not prevent these bugs from being
merged, at least triggered occasional crashes in advance of
production usages.
- Fix handling of ACPI DSM error status results. The DSM mechanism
allows communication with platform and memory device firmware. We
correctly parse known errors, but were silently ignoring others.
Fix it to consistently fail any command with a non-zero status return
that we otherwise do not interpret / handle.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, region: fix flush hint table thinko
nfit: fail DSMs that return non-zero status by default
libnvdimm: fix devm_nvdimm_memremap() error path
tools/testing/nvdimm: fix allocation range for mock flush hint tables
nvdimm: fix PHYS_PFN/PFN_PHYS mixup
|
|
Add support for reading addresses, interrupts, and _DSD properties
from ACPI tables, just like with device tree. The HID for the
EMAC device itself is QCOM8070. The internal PHY is represented
by a child node with a HID of QCOM8071.
The EMAC also has some complex clock initialization requirements
that are not represented by this patch. This will be addressed
in a future patch.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms. This
change makes it easier to add ACPI support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The platform_device returned by of_find_device_by_node() is not
automatically released when the driver unprobes. Therefore,
managed calls like devm_ioremap_resource() should not be used.
Instead, we manually allocate the resources and then free them
on driver release.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull late MTD fixes from Brian Norris:
"Another round of MTD fixes for v4.8
My apologies for sending this so late. I've been fairly absent as a
maintainer this cycle, but I did queue these up weeks ago. In the
meantime, Richard was able to handle some other fixes (thanks!) but
didn't pick these up.
On the bright side, these are very simple changes that should carry
little risk.
Summary:
- Davinci NAND: fix a long-standing bug in how we clear/prep 4-bit ECC
- OMAP NAND: an error-handling fix that made it into v4.8-rc1 caused
error-handling cases in other configurations/code-paths; this fixes
the fix"
* tag 'for-linus-20160928' of git://git.infradead.org/linux-mtd:
mtd: nand: davinci: Reinitialize the HW ECC engine in 4bit hwctl
mtd: nand: omap2: Don't call dma_release_channel() if dma_request_chan() failed
|
|
ath.git patches for 4.9. Major changes:
ath9k
* disable RNG by default
|
|
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add support for the first two members of the Renesas RZ/G family, RZ/G1M/E
(also known as R8A7743/5). The Ether core is the same as in the R-Car gen2
SoCs, so will share the code/data with them...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, in order to offload a FIB entry to HW we use switchdev op.
Use the newly introduced FIB notifier infrasturucture to process
FIB entries to offload the in HW.
Abort mechanism is now handled within the rocker driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, in order to offload a FIB entry to HW we use switchdev op.
However that has limits. Mainly in case we need to make the HW aware of
all route prefixes configured in kernel. HW needs to know those in order
to properly trap appropriate packets and pass the to kernel to do
the forwarding. Abort mechanism is now handled within the mlxsw driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The udl damage handler is supposed to render 'height' lines, but its
iterator has an obvious typo that makes it miss most lines if the
rectangle does not cover 0/0.
Fix the damage handler to correctly render all lines.
This is a fallout from:
commit e375882406d0cc24030746638592004755ed4ae0
Author: Noralf Trønnes <noralf@tronnes.org>
Date: Thu Apr 28 17:18:37 2016 +0200
drm/udl: Use drm_fb_helper deferred_io support
Tested-by: poma <poma@gmail.com>
Cc: stable@vger.kernel.org # 4.7+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump igb version to match other igb drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump version to match other igbvf drivers.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/intel/igb/igb_ethtool.c:2707:5: warning:
symbol 'igb_rxnfc_write_vlan_prio_filter' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
nouveau: couple of fixes.
* 'linux-4.8' of git://github.com/skeggsb/linux:
drm/nouveau: Revert "bus: remove cpu_coherent flag"
drm/nouveau/fifo/nv04: avoid ramht race against cookie insertion
|
|
into drm-fixes
two amd fixes.
* 'drm-fixes-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/si/dpm: add workaround for for Jet parts
drm/amdgpu: disable CRTCs before teardown
|
|
Add clock quirks for Jet parts.
Reviewed-by: Sonny Jiang <sonny.jiang@amd.com>
Tested-by: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some code called by drm_crtc_force_disable_all() wants to wait for all
fences, so only do fence teardown after CRTCs are disabled.
Fixes: 84b89bdcedf8 ("drm/amdgpu: Turn off CRTCs on driver unload")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Flowrings contain skbs waiting for transmission that were passed to us
by netif. It means we checked every one of them looking for 802.1x
Ethernet type. When deleting flowring we have to use freeing function
that will check for 802.1x type as well.
Freeing skbs without a proper check was leading to counter not being
properly decreased. This was triggering a WARNING every time
brcmf_netdev_wait_pend8021x was called.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend@broadcom.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Even with timeout increased to 950 ms we get WARNINGs from time to time.
It mostly happens on A-MPDU stalls (e.g. when station goes out of
range). It may take up to 5-10 secods for the firmware to recover and
for that time it doesn't process packets.
It's still useful to have a message on time out as it may indicate some
firmware problem and incorrect key update. Raising a WARNING however
wasn't really that necessary, it doesn't point to any driver bug anymore
and backtrace wasn't much useful.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The entries in this enum may be referenced in debug output. Adding explicit
values simplifies the lookup.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Only rtl8821ae implements WOWLAN; however, the other drivers may receive
a call requesting information about this mode. The other drivers need to
ignore the request rather than logging that the default branch of the
switch statement has been reached.
Reported by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Help along debugging by showing what switch/case variable is not
being processed in these messages.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Some new HW IDs;
* Small fix in CTDP error handling;
* Remove support for older firmwares;
* Clean-ups and a few simple fixes here and there.
|
|
The group list must be freed prior to freeing the command otherwise
we have a use-after-free.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(1) Modify the register settings for LRO relinquishments
(2) Jump out from the waiting loop while LRO relinquishments are done
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop PDMA while the frame engine is going to stop.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 6b352ebccbcf ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").
We needs to revert the commit 62469c76007e ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebccbcf ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
