| Age | Commit message (Collapse) | Author |
|---|
|
Disable runtime PM if register flexcandev failed, and balance reference
of usage_count.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929211557.14153-4-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add flexcan driver for i.MX8MP, which supports CAN FD and ECC.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929211557.14153-3-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
One issue was reported at a baremetal environment, which is used for
FPGA verification. "The first transfer will fail for extended ID
format(for both 2.0B and FD format), following frames can be transmitted
and received successfully for extended format, and standard format don't
have this issue. This issue occurred randomly with high possiblity, when
it occurs, the transmitter will detect a BIT1 error, the receiver a CRC
error. According to the spec, a non-correctable error may cause this
transfer failure."
With FLEXCAN_QUIRK_DISABLE_MECR quirk, it supports correctable errors,
disable non-correctable errors interrupt and freeze mode. Platform has
ECC hardware support, but select this quirk, this issue may not come to
light. Initialize all FlexCAN memory before accessing them, at least it
can avoid non-correctable errors detected due to memory uninitialized.
The internal region can't be initialized when the hardware doesn't support
ECC.
According to IMX8MPRM, Rev.C, 04/2020. There is a NOTE at the section
11.8.3.13 Detection and correction of memory errors:
"All FlexCAN memory must be initialized before starting its operation in
order to have the parity bits in memory properly updated. CTRL2[WRMFRZ]
grants write access to all memory positions that require initialization,
ranging from 0x080 to 0xADF and from 0xF28 to 0xFFF when the CAN FD feature
is enabled. The RXMGMASK, RX14MASK, RX15MASK, and RXFGMASK registers need to
be initialized as well. MCR[RFEN] must not be set during memory initialization."
Memory range from 0x080 to 0xADF, there are reserved memory (unimplemented
by hardware, e.g. only configure 64 MBs), these memory can be initialized or not.
In this patch, initialize all flexcan memory which includes reserved memory.
In this patch, create FLEXCAN_QUIRK_SUPPORT_ECC for platforms which has ECC
feature. If you have a ECC platform in your hand, please select this
qurik to initialize all flexcan memory firstly, then you can select
FLEXCAN_QUIRK_DISABLE_MECR to only enable correctable errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929211557.14153-2-qiangqing.zhang@nxp.com
[mkl: wrap long lines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all non user facing occurrence of
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD".
[1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Link: https://lore.kernel.org/r/20200930091424.792165-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all user facing strings from
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD", including:
- kconfig symbols
- name of kernel module
- DT and SPI compatible
[1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Link: https://lore.kernel.org/r/20200930091424.792165-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes the name of the driver subdir and the
individual files accordinly.
[1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Link: https://lore.kernel.org/r/20200930091424.792165-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix missing return statement when writing "off" to intel_pstate status
sysfs I/F.
Fixes: 55671ea3257a ("cpufreq: intel_pstate: Free memory only when turning off")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee032 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9b4 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We must free the vqs array in the open failure path, because
vhost_vdpa_release will not be called.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1600712588-9514-2-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
Also partially revert the follow-up change "drm: pl111: Absorb the
external register header".
This reverts the parts of commits
7e4e589db76a3cf4c1f534eb5a09cc6422766b93 and
0fb8125635e8eb5483fb095f98dcf0651206a7b8 that touch paths outside
of drivers/gpu/drm/pl111.
The fbdev driver is used by Android's FVP configuration. Using the
DRM driver together with DRM's fbdev emulation results in a failure
to boot Android. The root cause is that Android's generic fbdev
userspace driver relies on the ability to set the pixel format via
FBIOPUT_VSCREENINFO, which is not supported by fbdev emulation.
There have been other less critical behavioral differences identified
between the fbdev driver and the DRM driver with fbdev emulation. The
DRM driver exposes different values for the panel's width, height and
refresh rate, and the DRM driver fails a FBIOPUT_VSCREENINFO syscall
with yres_virtual greater than the maximum supported value instead
of letting the syscall succeed and setting yres_virtual based on yres.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929195344.2219796-1-pcc@google.com
|
|
gfxoff is temporarily disabled for navy_flounder, since
at present the feature caused some tdr when performing
display operations.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As the dpm clock table is needed during DC HW initialization.
And that (DC HW initialization) comes before smu_late_init()
where current APU dpm clock table setup is performed. So, NULL
pointer dereference will be triggered. By moving APU dpm clock
table setup to smu_hw_init(), this can be avoided.
Fixes: 02cf91c113ea ("drm/amd/powerplay: postpone operations not required for hw setup to late_init")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.9
- correct logic of GPIO_LINE_DIRECTION in gpio-amd-fch
|
|
"microchip,mcp251xfd"
The wildcard should be narrowed down to prevent existing and future devices
that are not compatible from matching. It is very unlikely that incompatible
devices will be released that do not match the wildcard.
Discussion Reference: https://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200930091423.755-1-thomas.kopp@microchip.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
set_normal mode
This patch fixes the following warning:
drivers/net/can/spi/mcp25xxfd/mcp25xxfd-core.c:2155 mcp25xxfd_irq()
error: uninitialized symbol 'set_normal_mode'.
by adding the missing initialization.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/r/20200923114726.2704426-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This loop doesn't free the first element of the array. The "i > 0" has
to be changed to "i >= 0".
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200923112752.GA1473821@mwanda
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The driver already implements the proposed fix.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200925065606.358-1-thomas.kopp@microchip.com
[mkl: split into two patches, adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
log messages
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The single error correction does not always work, so always indicate that a
single error occurred. If the location of the ECC error is outside of the
TX-RAM always use netdev_notice() to log the problem. For ECC errors in the
TX-RAM, there is a recovery procedure.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200925065606.358-1-thomas.kopp@microchip.com
[mkl: split into two patches, adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
clint_time_val will soon be used by the RISC-V implementation of
random_get_entropy(), which is a static inline function that may be used by
modules (at least CRYPTO_JITTERENTROPY=m).
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
ttm_mem_type_manager_func.get_node was changed to return -ENOSPC
instead of setting the node pointer to NULL. Unfortunately
vmwgfx still had two places where it was explicitly converting
-ENOSPC to 0 causing regressions. This fixes those spots by
allowing -ENOSPC to be returned. That seems to fix recent
regressions with vmwgfx.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Sigend-off-by: Roland Scheidegger <sroland@vmware.com>
|
|
The kernel may fail to boot or devices may fail to come up when
initializing iscsi_tcp devices starting with Linux 5.8.
Commit a79af8a64d39 ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param
libiscsi function") introduced getpeername() within the session spinlock.
Commit 1b66d253610c ("bpf: Add get{peer, sock}name attach types for
sock_addr") introduced BPF_CGROUP_RUN_SA_PROG_LOCK() within getpeername(),
which acquires a mutex and when used from iscsi_tcp devices can now lead to
"BUG: scheduling while atomic:" and subsequent damage.
Ensure that the spinlock is released before calling getpeername() or
getsockname(). sock_hold() and sock_put() are used to ensure that the
socket reference is preserved until after the getpeername() or
getsockname() complete.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1877345
Link: https://lkml.org/lkml/2020/7/28/1085
Link: https://lkml.org/lkml/2020/8/31/459
Link: https://lore.kernel.org/r/20200928043329.606781-1-mark.mielke@gmail.com
Fixes: a79af8a64d39 ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param libiscsi function")
Fixes: 1b66d253610c ("bpf: Add get{peer, sock}name attach types for sock_addr")
Cc: stable@vger.kernel.org
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Mark Mielke <mark.mielke@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently a new filter is created, containing just enough correct
information to be able to call ocelot_vcap_block_find_filter_by_index()
on it.
This will be limiting us in the future, when we'll have more metadata
associated with a filter, which will matter in the stats() and destroy()
callbacks, and which we can't make up on the spot. For example, we'll
start "offloading" some dummy tc filter entries for the TCAM skeleton,
but we won't actually be adding them to the hardware, or to block->rules.
So, it makes sense to avoid deleting those rules too. That's the kind of
thing which is difficult to determine unless we look up the real filter.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And rename the existing find to ocelot_vcap_block_find_filter_by_index.
The index is the position in the TCAM, and the id is the flow cookie
given by tc.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'cnt' variable is actually used for 2 purposes, to hold the number
of sub-words per VCAP entry, and the number of sub-words per VCAP
action.
In fact, I'm pretty sure these 2 numbers can never be different from one
another. By hardware definition, the entry (key) TCAM rows are divided
into the same number of sub-words as its associated action RAM rows.
But nonetheless, let's at least rename the variables such that
observations like this one are easier to make in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This gets rid of one of the 2 variables named, very generically,
"count".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calculating the offsets for the current entry within the row and
placing them inside struct vcap_data, the function assumes half key
entry (2 keys per row).
This patch modifies the vcap_data_offset_get() function to calculate a
correct data offset when the setting VCAP Type-Group of a key to
VCAP_TG_FULL or VCAP_TG_QUARTER.
This is needed because, for example, VCAP ES0 only supports full keys.
Also rename the 'count' variable to 'num_entries_per_row' to make the
function just one tiny bit easier to follow.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we'll make the switch to multiple chain offloading, we'll want to
know first what VCAP block the rule is offloaded to. This impacts what
keys are available. Since the VCAP block is determined by what actions
are used, parse the action first.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we are deriving these from the constants exposed by the
hardware, we can delete the static info we're keeping in the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although it doesn't look like it is possible to hit these conditions
from user space, there are 2 separate, but related, issues.
First, the ocelot_vcap_block_get_filter_index function, née
ocelot_ace_rule_get_index_id prior to the aae4e500e106 ("net: mscc:
ocelot: generalize the "ACE/ACL" names") rename, does not do what the
author probably intended. If the desired filter entry is not present in
the ACL block, this function returns an index equal to the total number
of filters, instead of -1, which is maybe what was intended, judging
from the curious initialization with -1, and the "++index" idioms.
Either way, none of the callers seems to expect this behavior.
Second issue, the callers don't actually check the return value at all.
So in case the filter is not found in the rule list, propagate the
return code.
So update the callers and also take the opportunity to get rid of the
odd coding idioms that appear to work but don't.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.
For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.
In plain ocelot_read, the target is encoded into the register enum
itself:
u16 target = reg >> TARGET_OFFSET;
For the VCAPs, the registers are currently defined like this:
enum ocelot_reg {
[...]
S2_CORE_UPDATE_CTRL = S2 << TARGET_OFFSET,
S2_CORE_MV_CFG,
S2_CACHE_ENTRY_DAT,
S2_CACHE_MASK_DAT,
S2_CACHE_ACTION_DAT,
S2_CACHE_CNT_DAT,
S2_CACHE_TG_DAT,
[...]
};
which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).
So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.
The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not use rx_desc pointers if possible since rx descriptors are stored in
uncached memory and dereferencing rx_desc pointers generate extra loads.
This patch improves XDP_DROP performance of ~ 110Kpps (700Kpps vs 590Kpps)
on Marvell Espressobin
Analyzed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VIA Technologies VT8251 South Bridge's integrated Rhine-II
Ethernet MAC comes has a PCI revision value of 0x7c. This was
verified on ASUS P5V800-VM mainboard.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rhine_resume() and rhine_suspend(), the code calls netif_running()
to see if the network interface is down or not. If it is down (i.e.,
netif_running() returning false), they will skip any housekeeping work
within the function relating to the hardware. This becomes a problem
when the hardware resumes from a standby since it is counting on
rhine_resume() to map its MMIO and power up rest of the hardware.
Not getting its MMIO remapped and rest of the hardware powered
up lead to a soft reset failure and hardware disappearance. The
solution is to map its MMIO and power up rest of the hardware inside
rhine_open() before soft reset is to be performed. This solution was
verified on ASUS P5V800-VM mainboard's integrated Rhine-II Ethernet
MAC inside VIA Technologies VT8251 South Bridge.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 78fe9f63947a2b ("drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions")
added a call to rn_vbios_smu_get_smu_version() to set clk_mgr->smu_ver.
That field is initialized prior to the if-statement, already.
Fixes: 78fe9f63947a2b (drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions)
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sung Lee <sung.lee@amd.com>
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The state array is in the reverse order compared to other asics
(high to low rather than low to high).
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1313
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e008fa6fb415 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config")
Cc: stable@vger.kernel.org
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Properly handle clang and older versions of gcc.
Fixes: e77165bf7b02a3 ("drm/amd/display: Add DCN3 blocks to Makefile")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
max_caps might be 0, thus hdcp_work might be ZERO_SIZE_PTR
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove gpu_info fw support for sienna_cichlid etc., since the
information can be retrieved from discovery binary.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SMU10_UMD_PSTATE_PEAK_FCLK value should not be used to set the DPM.
Suggested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Replace panic() call in lib8390.c with BUILD_BUG_ON()
since checking the size of struct e8390_pkt_hdr should
happen at compile-time.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl_lps_enter() and rtl_lps_leave() are using in_interrupt() to detect
whether it is safe to acquire a mutex or if it is required to defer to a
workqueue.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
in_interrupt() also is only partially correct because it fails to chose the
correct code path when just preemption or interrupts are disabled.
Add an argument 'may_block' to both functions and adjust the callers to
pass the context information.
The following call chains were analyzed to be safe to block:
rtl_watchdog_wq_callback()
rlf_lps_leave/enter()
rtl_op_suspend()
rtl_lps_leave()
rtl_op_bss_info_changed()
rtl_lps_leave()
rtl_op_sw_scan_start()
rtl_lps_leave()
The following call chains were analyzed to be unsafe to block:
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
setup_special_tx()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_tx_isr
rtl_lps_leave()
halbtc_leave_lps()
rtl_lps_leave()
This leaves four callers of rtl_lps_enter/leave() where the analyzis
stopped dead in the maze of several nested pointer based callchains and
lack of rtlwifi hardware to debug this via tracing:
halbtc_leave_lps(), halbtc_enter_lps(), halbtc_normal_lps(),
halbtc_pre_normal_lps()
These four have been cautionally marked to be unable to block which is the
safe option, but the rtwifi wizards should be able to clarify that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The usage of in_interrupt() in drivers in is phased out.
rtl_dbg() a printk based debug aid is using in_interrupt() in the
underlying C function _rtl_dbg_out() which is almost identical to
_rtl_dbg_print(). The only difference is the printout of in_interrupt().
The decoding of in_interrupt() as hexvalue is non-trivial and aside of
being phased out for driver usage the return value is just by chance the
masked preempt count value and not a boolean.
These home brewn printk debug aids are tedious to work with and provide
only minimal context. They should be replaced by trace_printk() or a debug
tracepoint which automatically records all context information.
To make progress on the in_interrupt() cleanup, make rtl_dbg() use
_rtl_dbg_print() and remove _rtl_dbg_out().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
