| Age | Commit message (Collapse) | Author |
|---|
|
Fix 3 typos in 8703b driver. 2 typos in calibration routines are not
fatal and do not seem to have any impact, just fix them to match vendor
driver.
However the last one in rtw8703b_set_channel_bb() clears too many bits
in REG_OFDM0_TX_PSD_NOISE, causing TX and RX issues (neither rate goes
above MCS0-MCS1). Vendor driver clears only 2 most significant bits.
With the last typo fixed, the driver is able to reach MCS7 on Pinebook
Cc: stable@vger.kernel.org
Fixes: 9bb762b3a957 ("wifi: rtw88: Add definitions for 8703b chip")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Fiona Klute <fiona.klute@gmx.de>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103075107.1337533-1-anarsoul@gmail.com
|
|
It's not used for anything.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/b80f7904-c6b4-4d12-a5f9-69ab9b965732@gmail.com
|
|
Add some extra configuration for USB devices. Currently only RTL8822BU
version (cut) D needs this. The new code makes use of the existing
usb3_param_8822b array from rtw8822b.c.
A user reported that TP-Link Archer T3U in USB 3 mode was randomly
disconnecting from USB:
[ 26.036502] usb 2-2: new SuperSpeed USB device number 3 using xhci_hcd
...
[ 27.576491] usb 2-2: USB disconnect, device number 3
[ 28.621528] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
...
[ 45.984521] usb 2-2: USB disconnect, device number 4
...
[ 46.845585] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
...
[ 94.400380] usb 2-2: USB disconnect, device number 5
...
[ 95.590421] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
This patch fixes that.
Link: https://github.com/lwfinger/rtw88/issues/262
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/9d312b14-0146-4be8-9c50-ef432234db50@gmail.com
|
|
RTL8922AE-VS is a variant of RTL8922AE, which is supported by firmware
version after 0.35.54.0 and only can support up to MCS11. Add a variant
struct to describe these requirements accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250108020955.14668-3-pkshih@realtek.com
|
|
Firmware after version 0.35.51.0 defines and exports more hardware
capabilities, which driver will consider reported QAM field as
EHT MCS capability to register hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250108020955.14668-2-pkshih@realtek.com
|
|
The rtwdev->scanning flag isn't protected by mutex originally, so
cancel_hw_scan can pass the condition, but suddenly hw_scan completion
unset the flag and calls ieee80211_scan_completed() that will free
local->hw_scan_req. Then, cancel_hw_scan raises null-ptr-deref and
use-after-free. Fix it by moving the check condition to where
protected by mutex.
KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f]
CPU: 2 PID: 6922 Comm: kworker/2:2 Tainted: G OE
Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB6WW (2.76 ) 09/10/2019
Workqueue: events cfg80211_conn_work [cfg80211]
RIP: 0010:rtw89_fw_h2c_scan_offload_be+0xc33/0x13c3 [rtw89_core]
Code: 00 45 89 6c 24 1c 0f 85 23 01 00 00 48 8b 85 20 ff ff ff 48 8d
RSP: 0018:ffff88811fd9f068 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff88811fd9f258 RCX: 0000000000000001
RDX: 0000000000000011 RSI: 0000000000000001 RDI: 0000000000000089
RBP: ffff88811fd9f170 R08: 0000000000000000 R09: 0000000000000000
R10: ffff88811fd9f108 R11: 0000000000000000 R12: ffff88810e47f960
R13: 0000000000000000 R14: 000000000000ffff R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8881d6f00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007531dfca55b0 CR3: 00000001be296004 CR4: 00000000001706e0
Call Trace:
<TASK>
? show_regs+0x61/0x73
? __die_body+0x20/0x73
? die_addr+0x4f/0x7b
? exc_general_protection+0x191/0x1db
? asm_exc_general_protection+0x27/0x30
? rtw89_fw_h2c_scan_offload_be+0xc33/0x13c3 [rtw89_core]
? rtw89_fw_h2c_scan_offload_be+0x458/0x13c3 [rtw89_core]
? __pfx_rtw89_fw_h2c_scan_offload_be+0x10/0x10 [rtw89_core]
? do_raw_spin_lock+0x75/0xdb
? __pfx_do_raw_spin_lock+0x10/0x10
rtw89_hw_scan_offload+0xb5e/0xbf7 [rtw89_core]
? _raw_spin_unlock+0xe/0x24
? __mutex_lock.constprop.0+0x40c/0x471
? __pfx_rtw89_hw_scan_offload+0x10/0x10 [rtw89_core]
? __mutex_lock_slowpath+0x13/0x1f
? mutex_lock+0xa2/0xdc
? __pfx_mutex_lock+0x10/0x10
rtw89_hw_scan_abort+0x58/0xb7 [rtw89_core]
rtw89_ops_cancel_hw_scan+0x120/0x13b [rtw89_core]
ieee80211_scan_cancel+0x468/0x4d0 [mac80211]
ieee80211_prep_connection+0x858/0x899 [mac80211]
ieee80211_mgd_auth+0xbea/0xdde [mac80211]
? __pfx_ieee80211_mgd_auth+0x10/0x10 [mac80211]
? cfg80211_find_elem+0x15/0x29 [cfg80211]
? is_bss+0x1b7/0x1d7 [cfg80211]
ieee80211_auth+0x18/0x27 [mac80211]
cfg80211_mlme_auth+0x3bb/0x3e7 [cfg80211]
cfg80211_conn_do_work+0x410/0xb81 [cfg80211]
? __pfx_cfg80211_conn_do_work+0x10/0x10 [cfg80211]
? __kasan_check_read+0x11/0x1f
? psi_group_change+0x8bc/0x944
? __kasan_check_write+0x14/0x22
? mutex_lock+0x8e/0xdc
? __pfx_mutex_lock+0x10/0x10
? __pfx___radix_tree_lookup+0x10/0x10
cfg80211_conn_work+0x245/0x34d [cfg80211]
? __pfx_cfg80211_conn_work+0x10/0x10 [cfg80211]
? update_cfs_rq_load_avg+0x3bc/0x3d7
? sched_clock_noinstr+0x9/0x1a
? sched_clock+0x10/0x24
? sched_clock_cpu+0x7e/0x42e
? newidle_balance+0x796/0x937
? __pfx_sched_clock_cpu+0x10/0x10
? __pfx_newidle_balance+0x10/0x10
? __kasan_check_read+0x11/0x1f
? psi_group_change+0x8bc/0x944
? _raw_spin_unlock+0xe/0x24
? raw_spin_rq_unlock+0x47/0x54
? raw_spin_rq_unlock_irq+0x9/0x1f
? finish_task_switch.isra.0+0x347/0x586
? __schedule+0x27bf/0x2892
? mutex_unlock+0x80/0xd0
? do_raw_spin_lock+0x75/0xdb
? __pfx___schedule+0x10/0x10
process_scheduled_works+0x58c/0x821
worker_thread+0x4c7/0x586
? __kasan_check_read+0x11/0x1f
kthread+0x285/0x294
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x29/0x6f
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 895907779752 ("rtw89: 8852a: add ieee80211_ops::hw_scan")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250107114254.6769-1-pkshih@realtek.com
|
|
For each MCC role, time limits, including max_tob_us, max_toa_us, and
mac_dur_us, are calculated if there are NoA attributes. The relation
between these time limits is "max_dur_us = max_tob_us + max_toa_us".
Then, the unit is converted from us to TU. However, originally, each
time limit was divided by 1024 independently. It missed to consider
the cases that max_tob_us or max_toa_us is not divisible by 1024. It
causes the result breaks "max_dur (TU) = max_tob (TU) + max_toa (TU)".
Finally, when MCC calculates pattern parameters based on these kinds
of time limits, it might not perform well.
Fixes: b09df09b55fb ("wifi: rtw89: mcc: initialize start flow")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103074412.124066-1-pkshih@realtek.com
|
|
For early chips, the RX BD info contains FS/LS bits for first/last segments
of a receiving packet. For 8922AE, the FS bit should be ignored, or it
may throw warning:
rtw89_8922ae 0000:1a:00.0: skb should not be ready before first segment start
To have compatible logic, FS determined by what pending skb is existing
(!new) or not.
Since we expect every single receiving packet in single one segment,
enlarge 4 bytes for RX BD info, and add a debug message to note if
RX buffer is possibly smaller than expected size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103025126.15378-1-pkshih@realtek.com
|
|
If WoWLAN failed in resume flow, the rtw89_ops_add_interface() triggered
without removing the interface first. Then the mgnt_entry list init again,
causing the list_empty() check in rtw89_chanctx_ops_assign_vif()
useless, and list_add_tail() again. Therefore, we have added a check to
prevent double adding of the list.
rtw89_8852ce 0000:01:00.0: failed to check wow status disabled
rtw89_8852ce 0000:01:00.0: wow: failed to check disable fw ready
rtw89_8852ce 0000:01:00.0: wow: failed to swap to normal fw
rtw89_8852ce 0000:01:00.0: failed to disable wow
rtw89_8852ce 0000:01:00.0: failed to resume for wow -110
rtw89_8852ce 0000:01:00.0: MAC has already powered on
i2c_hid_acpi i2c-ILTK0001:00: PM: acpi_subsys_resume+0x0/0x60 returned 0 after 284705 usecs
list_add corruption. prev->next should be next (ffff9d9719d82228), but was ffff9d9719f96030. (prev=ffff9d9719f96030).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:34!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 6918 Comm: kworker/u8:19 Tainted: G U O
Hardware name: Google Anraggar/Anraggar, BIOS Google_Anraggar.15217.514.0 03/25/2024
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:__list_add_valid_or_report+0x9f/0xb0
Code: e8 56 89 ff ff 0f 0b 48 c7 c7 3e fc e0 96 48 89 c6 e8 45 89 ff ...
RSP: 0018:ffffa51b42bbbaf0 EFLAGS: 00010246
RAX: 0000000000000075 RBX: ffff9d9719d82ab0 RCX: 13acb86e047a4400
RDX: 3fffffffffffffff RSI: 0000000000000000 RDI: 00000000ffffdfff
RBP: ffffa51b42bbbb28 R08: ffffffff9768e250 R09: 0000000000001fff
R10: ffffffff9765e250 R11: 0000000000005ffd R12: ffff9d9719f95c40
R13: ffff9d9719f95be8 R14: ffff9d97081bfd78 R15: ffff9d9719d82060
FS: 0000000000000000(0000) GS:ffff9d9a6fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007e7d029a4060 CR3: 0000000345e38000 CR4: 0000000000750ee0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body+0x68/0xb0
? die+0xaa/0xd0
? do_trap+0x9f/0x170
? __list_add_valid_or_report+0x9f/0xb0
? __list_add_valid_or_report+0x9f/0xb0
? handle_invalid_op+0x69/0x90
? __list_add_valid_or_report+0x9f/0xb0
? exc_invalid_op+0x3c/0x50
? asm_exc_invalid_op+0x16/0x20
? __list_add_valid_or_report+0x9f/0xb0
rtw89_chanctx_ops_assign_vif+0x1f9/0x210 [rtw89_core cbb375c44bf28564ce479002bff66617a25d9ac1]
? __mutex_unlock_slowpath+0xa0/0xf0
rtw89_ops_assign_vif_chanctx+0x4b/0x90 [rtw89_core cbb375c44bf28564ce479002bff66617a25d9ac1]
drv_assign_vif_chanctx+0xa7/0x1f0 [mac80211 6efaad16237edaaea0868b132d4f93ecf918a8b6]
ieee80211_reconfig+0x9cb/0x17b0 [mac80211 6efaad16237edaaea0868b132d4f93ecf918a8b6]
? __pfx_wiphy_resume+0x10/0x10 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
? dev_printk_emit+0x51/0x70
? _dev_info+0x6e/0x90
wiphy_resume+0x89/0x180 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
? __pfx_wiphy_resume+0x10/0x10 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
dpm_run_callback+0x37/0x1e0
device_resume+0x26d/0x4b0
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x29/0xd0
worker_thread+0x397/0x970
kthread+0xed/0x110
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x38/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 68ec751b2881 ("wifi: rtw89: chan: manage active interfaces")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103024500.14990-1-pkshih@realtek.com
|
|
Header conversion should only be used with MLO connections. Otherwise
P2P connection fails due to wrong probe responses sent. Fix it
accordingly.
Fixes: b8499664fca9 ("wifi: rtw89: Add header conversion for MLO connections")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-4-pkshih@realtek.com
|
|
During rtw89_entity_recalc_mgnt_roles(), there is a normalizing process
which will re-order the list if an entry with target pattern is found.
And once one is found, should have aborted the list_for_each_entry. But,
`break` just aborted the inner for-loop. The outer list_for_each_entry
still continues. Normally, only the first entry will match the target
pattern, and the re-ordering will change nothing, so there won't be
soft lockup. However, in some special cases, soft lockup would happen.
Fix it by `goto fill` to break from the list_for_each_entry.
The following is a sample of kernel log for this problem.
watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [wpa_supplicant:2055]
[...]
RIP: 0010:rtw89_entity_recalc ([...] chan.c:392 chan.c:479) rtw89_core
[...]
Fixes: 68ec751b2881 ("wifi: rtw89: chan: manage active interfaces")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-3-pkshih@realtek.com
|
|
When starting/proceeding MCC, it will abort an ongoing hw scan process.
In the proceeding cases, it unexpectedly tries to abort a non-exist hw
scan process. Then, a trace shown at the bottom will happen. This problem
is caused by a previous commit which changed some call sequence inside
rtw89_hw_scan_complete() to fix some coex problems. These changes lead
to our scanning flag was not cleared when proceeding MCC. To keep the
fixes on coex, and resolve the problem here, re-consider the related
call sequence.
The known sequence requirements are listed below.
* the old sequence:
A. notify coex
B. clear scanning flag
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
(the problem: A needs to be after C-1)
* the current sequence:
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
A. notify coex
B. clear scanning flag
(the problem: C-2 needs to be after B)
So, now let hw scan caller pass a callback to proceed chanctx if needed.
Then, the new sequence will be like the below.
C-1. set channel
A. notify coex
B. clear scanning flag
C-2. proceed MCC
The following is the kernel log for the problem in current sequence.
rtw89_8852be 0000:04:00.0: rtw89_hw_scan_offload failed ret -110
------------[ cut here ]------------
[...]
CPU: 2 PID: 3991 Comm: kworker/u16:0 Tainted: G OE 6.6.17 #3
Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB3WW (2.73 ) 11/28/2018
Workqueue: events_unbound wiphy_work_cancel [cfg80211]
RIP: 0010:ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
Code: 9c 24 d0 11 00 00 49 39 dd 0f 85 46 ff ff ff 4c 89 e7 e8 09 2d
RSP: 0018:ffffb27783643d48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff8a2280964bc0 RSI: 0000000000000000 RDI: ffff8a23df580900
RBP: ffffb27783643d88 R08: 0000000000000001 R09: 0000000000000400
R10: 0000000000000000 R11: 0000000000008268 R12: ffff8a23df580900
R13: ffff8a23df581b00 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8a258e680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f26a0654000 CR3: 000000002ea2e002 CR4: 00000000001706e0
Call Trace:
<TASK>
? show_regs+0x68/0x70
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? __warn+0x8f/0x150
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? report_bug+0x1f5/0x200
? handle_bug+0x46/0x80
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
ieee80211_scan_work+0x14a/0x650 [mac80211]
? __queue_work+0x10f/0x410
wiphy_work_cancel+0x2fb/0x310 [cfg80211]
process_scheduled_works+0x9d/0x390
? __pfx_worker_thread+0x10/0x10
worker_thread+0x15b/0x2d0
? __pfx_worker_thread+0x10/0x10
kthread+0x108/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c/0x60
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: f16c40acd319 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-2-pkshih@realtek.com
|
|
Limit ETS QoS channel to AIROHA_NUM_QOS_CHANNELS in
airoha_tc_setup_qdisc_ets() in order to align the configured channel to
the value set in airoha_dev_select_queue().
Fixes: 20bf7d07c956 ("net: airoha: Add sched ETS offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250107-airoha-ets-fix-chan-v1-1-97f66ed3a068@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DP83822 supports up to three configurable Light Emitting Diode (LED)
pins: LED_0, LED_1 (GPIO1), COL (GPIO2) and RX_D3 (GPIO3). Several
functions can be multiplexed onto the LEDs for different modes of
operation. LED_0 and COL (GPIO2) use the MLED function. MLED can be routed
to only one of these two pins at a time. Add minimal LED controller driver
supporting the most common uses with the 'netdev' trigger.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250107-dp83822-leds-v2-1-5b260aad874f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"One patch to fix error handling in drivetemp driver"
* tag 'hwmon-for-v6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (drivetemp) Fix driver producing garbage data when SCSI errors occur
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-01-10
Pierre-Henry Moussay adds PIC64GX compatibility to the DT bindings for
Microchip's mpfs-can IP core.
The next 3 patches are by Sean Nyekjaer and target the tcan4x5x
driver. First the DT bindings is converted to DT schema, then nWKRQ
voltage selection is added to the driver.
Dario Binacchi's patch for the sun4i_can makes the driver more
consistent by adding a likely() to the driver.
Another patch by Sean Nyekjaer for the tcan4x5x driver gets rid of a
false error message.
Charan Pedumuru converts the atmel-can DT bindings to DT schema.
The next 2 patches are by Oliver Hartkopp. The first one maps Oliver's
former mail addresses to a dedicated CAN mail address. The second one
assigns net/sched/em_canid.c additionally to the CAN maintainers.
Ariel Otilibili's patch removes dead code from the CAN dev helper.
The next 3 patches are by Sean Nyekjaer and add HW standby support to
the tcan4x5x driver.
A patch by Dario Binacchi fixes the DT bindings for the st,stm32-bxcan
driver.
The last 4 patches are by Jimmy Assarsson and target the kvaser_usb
and the kvaser_pciefd driver: error statistics are improved and
CAN_CTRLMODE_BERR_REPORTING is added.
* tag 'linux-can-next-for-6.14-20250110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: kvaser_pciefd: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_pciefd: Update stats and state even if alloc_can_err_skb() fails
can: kvaser_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_usb: Update stats and state even if alloc_can_err_skb() fails
dt-bindings: can: st,stm32-bxcan: fix st,gcan property type
can: m_can: call deinit/init callback when going into suspend/resume
can: tcan4x5x: add deinit callback to set standby mode
can: m_can: add deinit callback
can: dev: can_get_state_str(): Remove dead code
MAINTAINERS: assign em_canid.c additionally to CAN maintainers
mailmap: add an entry for Oliver Hartkopp
dt-bindings: net: can: atmel: Convert to json schema
can: tcan4x5x: get rid of false clock errors
can: sun4i_can: continue to use likely() to check skb
can: tcan4x5x: add option for selecting nWKRQ voltage
dt-bindings: can: tcan4x5x: Document the ti,nwkrq-voltage-vio option
dt-bindings: can: convert tcan4x5x.txt to DT schema
dt-bindings: can: mpfs: add PIC64GX CAN compatibility
====================
Link: https://patch.msgid.link/20250110112712.3214173-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In all 3 cases (cpsw, cpsw-new, am65-cpsw) ALE is being configured in
VLAN-aware mode, while the comment states the opposite. Seems to be a typo
copy-pasted from one driver to another. Fix the commend which has been
puzzling some people (including me) for at least a decade.
Link: https://lore.kernel.org/linux-arm-kernel/4699400.vD3TdgH1nR@localhost/
Link: https://lore.kernel.org/netdev/0106ce78-c83f-4552-a234-1bf7a33f1ed1@kernel.org/
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250109214219.123767-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When tx_max_frame_size was added to struct ravb_hw_info, no value was
set in ravb_rzv2m_hw_info so the default value of zero was used.
The maximum MTU is set by subtracting from tx_max_frame_size to allow
space for headers and frame checksums. As ndev->max_mtu is unsigned,
this subtraction wraps around leading to a ridiculously large positive
value that is obviously incorrect.
Before tx_max_frame_size was introduced, the maximum MTU was based on
rx_max_frame_size. So, we can restore the correct maximum MTU by copying
the rx_max_frame_size value into tx_max_frame_size for RZ/V2M.
Fixes: 1d63864299ca ("net: ravb: Fix maximum TX frame size for GbEth devices")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://patch.msgid.link/20250109113706.1409149-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mana_driver_exit(), mana_debugfs_root gets cleanup before any of it's
children (which happens later in the pci_unregister_driver()).
Due to this, when mana driver is configured as a module and rmmod is
invoked, following stack gets printed along with failure in rmmod command.
[ 2399.317651] BUG: kernel NULL pointer dereference, address: 0000000000000098
[ 2399.318657] #PF: supervisor write access in kernel mode
[ 2399.319057] #PF: error_code(0x0002) - not-present page
[ 2399.319528] PGD 10eb68067 P4D 0
[ 2399.319914] Oops: Oops: 0002 [#1] SMP NOPTI
[ 2399.320308] CPU: 72 UID: 0 PID: 5815 Comm: rmmod Not tainted 6.13.0-rc5+ #89
[ 2399.320986] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 09/28/2024
[ 2399.321892] RIP: 0010:down_write+0x1a/0x50
[ 2399.322303] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 54 49 89 fc e8 9d cd ff ff 31 c0 ba 01 00 00 00 <f0> 49 0f b1 14 24 75 17 65 48 8b 05 f6 84 dd 5f 49 89 44 24 08 4c
[ 2399.323669] RSP: 0018:ff53859d6c663a70 EFLAGS: 00010246
[ 2399.324061] RAX: 0000000000000000 RBX: ff1d4eb505060180 RCX: ffffff8100000000
[ 2399.324620] RDX: 0000000000000001 RSI: 0000000000000064 RDI: 0000000000000098
[ 2399.325167] RBP: ff53859d6c663a78 R08: 00000000000009c4 R09: ff1d4eb4fac90000
[ 2399.325681] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000098
[ 2399.326185] R13: ff1d4e42e1a4a0c8 R14: ff1d4eb538ce0000 R15: 0000000000000098
[ 2399.326755] FS: 00007fe729570000(0000) GS:ff1d4eb2b7200000(0000) knlGS:0000000000000000
[ 2399.327269] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2399.327690] CR2: 0000000000000098 CR3: 00000001c0584005 CR4: 0000000000373ef0
[ 2399.328166] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2399.328623] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 2399.329055] Call Trace:
[ 2399.329243] <TASK>
[ 2399.329379] ? show_regs+0x69/0x80
[ 2399.329602] ? __die+0x25/0x70
[ 2399.329856] ? page_fault_oops+0x271/0x550
[ 2399.330088] ? psi_group_change+0x217/0x470
[ 2399.330341] ? do_user_addr_fault+0x455/0x7b0
[ 2399.330667] ? finish_task_switch.isra.0+0x91/0x2f0
[ 2399.331004] ? exc_page_fault+0x73/0x160
[ 2399.331275] ? asm_exc_page_fault+0x27/0x30
[ 2399.343324] ? down_write+0x1a/0x50
[ 2399.343631] simple_recursive_removal+0x4d/0x2c0
[ 2399.343977] ? __pfx_remove_one+0x10/0x10
[ 2399.344251] debugfs_remove+0x45/0x70
[ 2399.344511] mana_destroy_rxq+0x44/0x400 [mana]
[ 2399.344845] mana_destroy_vport+0x54/0x1c0 [mana]
[ 2399.345229] mana_detach+0x2f1/0x4e0 [mana]
[ 2399.345466] ? ida_free+0x150/0x160
[ 2399.345718] ? __cond_resched+0x1a/0x50
[ 2399.345987] mana_remove+0xf4/0x1a0 [mana]
[ 2399.346243] mana_gd_remove+0x25/0x80 [mana]
[ 2399.346605] pci_device_remove+0x41/0xb0
[ 2399.346878] device_remove+0x46/0x70
[ 2399.347150] device_release_driver_internal+0x1e3/0x250
[ 2399.347831] ? klist_remove+0x81/0xe0
[ 2399.348377] driver_detach+0x4b/0xa0
[ 2399.348906] bus_remove_driver+0x83/0x100
[ 2399.349435] driver_unregister+0x31/0x60
[ 2399.349919] pci_unregister_driver+0x40/0x90
[ 2399.350492] mana_driver_exit+0x1c/0xb50 [mana]
[ 2399.351102] __do_sys_delete_module.constprop.0+0x184/0x320
[ 2399.351664] ? __fput+0x1a9/0x2d0
[ 2399.352200] __x64_sys_delete_module+0x12/0x20
[ 2399.352760] x64_sys_call+0x1e66/0x2140
[ 2399.353316] do_syscall_64+0x79/0x150
[ 2399.353813] ? syscall_exit_to_user_mode+0x49/0x230
[ 2399.354346] ? do_syscall_64+0x85/0x150
[ 2399.354816] ? irqentry_exit+0x1d/0x30
[ 2399.355287] ? exc_page_fault+0x7f/0x160
[ 2399.355756] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2399.356302] RIP: 0033:0x7fe728d26aeb
[ 2399.356776] Code: 73 01 c3 48 8b 0d 45 33 0f 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 15 33 0f 00 f7 d8 64 89 01 48
[ 2399.358372] RSP: 002b:00007ffff954d6f8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 2399.359066] RAX: ffffffffffffffda RBX: 00005609156cc760 RCX: 00007fe728d26aeb
[ 2399.359779] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005609156cc7c8
[ 2399.360535] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 2399.361261] R10: 00007fe728dbeac0 R11: 0000000000000206 R12: 00007ffff954d950
[ 2399.361952] R13: 00005609156cc2a0 R14: 00007ffff954ee5f R15: 00005609156cc760
[ 2399.362688] </TASK>
Fixes: 6607c17c6c5e ("net: mana: Enable debugfs files for MANA device")
Cc: stable@vger.kernel.org
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1736398991-764-1-git-send-email-shradhagupta@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This allows ipvlan to function properly on top of
bonds using active-backup mode.
This was implemented for macvlan in 2014 in commit
4c9912556867 ("macvlan: Support bonding events").
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Link: https://patch.msgid.link/20250109032819.326528-2-champetier.etienne@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recalculate features when XDP is detached.
Before:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: off [requested on]
After:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: on
The fact that HW-GRO doesn't get re-enabled automatically is just
a minor annoyance. The real issue is that the features will randomly
come back during another reconfiguration which just happens to invoke
netdev_update_features(). The driver doesn't handle reconfiguring
two things at a time very robustly.
Starting with commit 98ba1d931f61 ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") we only reconfigure the RSS hash table
if the "effective" number of Rx rings has changed. If HW-GRO is
enabled "effective" number of rings is 2x what user sees.
So if we are in the bad state, with HW-GRO re-enablement "pending"
after XDP off, and we lower the rings by / 2 - the HW-GRO rings
doing 2x and the ethtool -L doing / 2 may cancel each other out,
and the:
if (old_rx_rings != bp->hw_resc.resv_rx_rings &&
condition in __bnxt_reserve_rings() will be false.
The RSS map won't get updated, and we'll crash with:
BUG: kernel NULL pointer dereference, address: 0000000000000168
RIP: 0010:__bnxt_hwrm_vnic_set_rss+0x13a/0x1a0
bnxt_hwrm_vnic_rss_cfg_p5+0x47/0x180
__bnxt_setup_vnic_p5+0x58/0x110
bnxt_init_nic+0xb72/0xf50
__bnxt_open_nic+0x40d/0xab0
bnxt_open_nic+0x2b/0x60
ethtool_set_channels+0x18c/0x1d0
As we try to access a freed ring.
The issue is present since XDP support was added, really, but
prior to commit 98ba1d931f61 ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") it wasn't causing major issues.
Fixes: 1054aee82321 ("bnxt_en: Use NETIF_F_GRO_HW.")
Fixes: 98ba1d931f61 ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://patch.msgid.link/20250109043057.2888953-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove stmmac_lpi_entry_timer_config(), setting priv->eee_sw_timer_en
at the original call sites, and calling the appropriate
stmmac_xxx_hw_lpi_timer() function. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEq-0002LQ-PC@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide stmmac_disable_hw_lpi_timer() and stmmac_enable_hw_lpi_timer()
to control the hardware transmit LPI timer.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEl-0002LK-LA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink_stop() will cause phylink to call the mac_link_down() operation
before phylink_stop() returns. As mac_link_down() will call
stmmac_eee_init(false), this will set both priv->eee_active and
priv->eee_enabled to be false, deleting the eee_ctrl_timer if
priv->eee_enabled was previously set.
As stmmac_release() calls phylink_stop() before checking whether
priv->eee_enabled is true, this is a condition that can never be
satisfied, and thus the code within this if() block will never be
executed. Remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEg-0002LE-HH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the initialisation of the EEE software timer to the probe function
as it is unnecessary to do this each time we enable software LPI.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEb-0002L8-DJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->eee_enabled and priv->eee_active are both assigned using boolean
values. Type them as bool rather than int.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEW-0002L2-9w@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since all call sites of stmmac_eee_init() assign priv->eee_active
immediately before, pass this state into stmmac_eee_init() and
assign priv->eee_active within this function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZER-0002Kv-5O@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All call sites for stmmac_eee_init() assign the return code to
priv->eee_enabled. Rather than having this coded at each call site,
move the assignment inside stmmac_eee_init().
Since stmmac_init_eee() takes priv->lock before checking the state of
priv->eee_enabled, move the assignment within the locked region. Also,
stmmac_suspend() checks the state of this member under the lock. While
two concurrent calls to stmmac_init_eee() aren't possible, there is
a possibility that stmmac_suspend() may run concurrently with a change
of priv->eee_enabled unless we modify it under the lock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEM-0002Kq-2Z@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->eee_tw_timer is only assigned during initialisation to a
constant value (STMMAC_DEFAULT_TWT_LS) and then never changed.
Remove priv->eee_tw_timer, and instead use STMMAC_DEFAULT_TWT_LS
for both uses in stmmac_eee_init().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEG-0002Kk-VH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert stmmac to use phy_eee_rx_clock_stop() to set the PHY receive
clock stop in LPI setting, rather than calling the legacy
phy_init_eee() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZEB-0002Ke-RZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Report the number of EEE error statistics in the xstats even when EEE
is not enabled in hardware, but is supported. The PHY maintains this
counter even when EEE is not enabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZE6-0002KY-Nx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Through using phylib's EEE state, priv->tx_lpi_enabled has become a
write-only variable. Remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZE1-0002KS-K1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_disable_eee_mode() is now only called from stmmac_xmit() when
both priv->tx_path_in_lpi_mode and priv->eee_sw_timer_en are true.
Therefore:
if (!priv->eee_sw_timer_en)
in stmmac_disable_eee_mode() will never be true, so this is dead code.
Remove it, and rename the function to indicate that it now only deals
with software based EEE mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDw-0002KL-Gg@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setting edata->tx_lpi_enabled in stmmac_ethtool_op_get_eee() gets
overwritten by phylib, so there's no point setting this.
In stmmac_ethtool_op_set_eee(), now that stmmac is using the result of
phylib's evaluation of EEE, there is no need to handle anything in the
ethtool EEE ops other than calling through to the appropriate phylink
function, which will pass on to phylib the users request.
As stmmac_disable_eee_mode() is now no longer called from outside
stmmac_main.c, make it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDr-0002KF-Cv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make stmmac EEE depend on phylib's evaluation of user settings and PHY
negotiation, as indicated by phy->enable_tx_lpi. This will ensure when
phylib has evaluated that the user has disabled LPI, phy_init_eee()
will not be called, and priv->eee_active will be false, causing LPI/EEE
to be disabled.
This is an interim measure - phy_init_eee() will be removed in a later
patch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDm-0002K9-9w@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since eee_timer is used to initialise priv->tx_lpi_timer, this also
should be unsigned to avoid a negative number being interpreted as a
very large positive number. Note that this makes the check for negative
numbers passed in as a module parameter redundant, and passing a
negative number will now produce a large delay rather than the
default. Since the default is used without an argument, passing a
negative number would be quite obscure. However, if users do, then
this will need to be revisited.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDh-0002K3-6y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethtool interface uses u32 for tx_lpi_timer, and so does phylib.
Use u32 to store this internally within stmmac rather than "int"
which could misinterpret large values.
Correct "value" in dwmac4_set_eee_lpi_entry_timer() to use u32
rather than int, which is derived from tx_lpi_timer. Even though this
path won't be used with values larger than STMMAC_ET_MAX, this brings
consistency of type usage to the stmmac code for this variable.
We leave eee_timer unchanged for now, with the assumption that values
up to INT_MAX will safely fit in a u32.
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDc-0002Jx-3b@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When stmmac_ethtool_op_get_eee() is called, stmmac sets the tx_lpi_timer
and tx_lpi_enabled members, and then calls into phylink and thus phylib.
phylib overwrites these members.
phylib will also cause a link down/link up transition when settings
that impact the MAC have been changed.
Convert stmmac to use the tx_lpi_timer setting in struct phy_device,
updating priv->tx_lpi_timer each time when the link comes up, rather
than trying to maintain this user setting itself. We initialise the
phylib tx_lpi_timer setting by doing a get_ee-modify-set_eee sequence
with the last known priv->tx_lpi_timer value. In order for this to work
correctly, we also need this member to be initialised earlier.
As stmmac_eee_init() is no longer called outside of stmmac_main.c, make
it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDW-0002Jr-W3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function to allow configuration of the PCS's clock stop enable
bit, used to configure whether the xMII receive clock can be stopped
during LPI mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDR-0002Jl-Ry@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix an OF node leak in the code parsing thermal zone DT properties
(Joe Hattori)"
* tag 'thermal-6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: of: fix OF node leak in of_thermal_zone_find()
|
|
In 'ath9k_hw_get_nf_hist_mid()', prefer 'memcpy()' and 'sort()'
over an ad-hoc things. Briefly tested as a separate module.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250109080703.106692-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Add two more ACPI IRQ override quirks and update the code using them
to avoid unnecessary overhead (Hans de Goede)"
* tag 'acpi-6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: acpi_dev_irq_override(): Check DMI match last
ACPI: resource: Add TongFang GM5HG0A to irq1_edge_low_force_override[]
ACPI: resource: Add Asus Vivobook X1504VAP to irq1_level_low_skip_override[]
|
|
Pull drm fixes from Dave Airlie:
"Regular weekly fixes, this has the usual amdgpu/xe/i915 bits.
There is a bigger bunch of mediatek patches that I considered not
including at this stage, but all the changes (except for one were
obvious small fixes, and the rotation one is a few lines, and I
suppose will help someone have their screen up the right way), I
decided to include it since I expect it got slowed down by holidays
etc, and it's not that mainstream a hw platform.
i915:
- Revert "drm/i915/hdcp: Don't enable HDCP1.4 directly from
check_link"
amdgpu:
- Display interrupt fixes
- Fix display max surface mismatches
- Fix divide error in DM plane scale calcs
- Display divide by 0 checks in dml helpers
- SMU 13 AD/DC interrrupt handling fix
- Fix locking around buddy trim handling
amdkfd:
- Fix page fault with shader debugger enabled
- Fix eviction fence wq handling
xe:
- Avoid a NULL ptr deref when wedging
- Fix power gate sequence on DG1
mediatek:
- Revert "drm/mediatek: dsi: Correct calculation formula of PHY
Timing"
- Set private->all_drm_private[i]->drm to NULL if mtk_drm_bind
returns err
- Move mtk_crtc_finish_page_flip() to ddp_cmdq_cb()
- Only touch DISP_REG_OVL_PITCH_MSB if AFBC is supported
- Add support for 180-degree rotation in the display driver
- Stop selecting foreign drivers
- Revert "drm/mediatek: Switch to for_each_child_of_node_scoped()"
- Fix YCbCr422 color format issue for DP
- Fix mode valid issue for dp
- dp: Reference common DAI properties
- dsi: Add registers to pdata to fix MT8186/MT8188
- Remove unneeded semicolon
- Add return value check when reading DPCD
- Initialize pointer in mtk_drm_of_ddp_path_build_one()"
* tag 'drm-fixes-2025-01-11' of https://gitlab.freedesktop.org/drm/kernel: (26 commits)
drm/xe/dg1: Fix power gate sequence.
drm/xe: Fix tlb invalidation when wedging
Revert "drm/i915/hdcp: Don't enable HDCP1.4 directly from check_link"
drm/amdgpu: Add a lock when accessing the buddy trim function
drm/amd/pm: fix BUG: scheduling while atomic
drm/amdkfd: wq_release signals dma_fence only when available
drm/amd/display: Add check for granularity in dml ceil/floor helpers
drm/amdkfd: fixed page fault when enable MES shader debugger
drm/amd/display: fix divide error in DM plane scale calcs
drm/amd/display: increase MAX_SURFACES to the value supported by hw
drm/amd/display: fix page fault due to max surface definition mismatch
drm/amd/display: Remove unnecessary amdgpu_irq_get/put
drm/mediatek: Initialize pointer in mtk_drm_of_ddp_path_build_one()
drm/mediatek: Add return value check when reading DPCD
drm/mediatek: Remove unneeded semicolon
drm/mediatek: mtk_dsi: Add registers to pdata to fix MT8186/MT8188
dt-bindings: display: mediatek: dp: Reference common DAI properties
drm/mediatek: Fix mode valid issue for dp
drm/mediatek: Fix YCbCr422 color format issue for DP
Revert "drm/mediatek: Switch to for_each_child_of_node_scoped()"
...
|
|
Add support to request pdev puncture stats from firmware through
HTT stats type 46. These stats give the count of number of
subbands used in different wifi standards.
Sample output:
-------------
echo 46 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_ofdm_su_last_used_pattern_mask = 0x00000001
tx_ofdm_su_num_subbands_used_cnt_01 = 217
tx_ofdm_su_num_subbands_used_cnt_02 = 0
tx_ofdm_su_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_ax_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
tx_ax_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
tx_be_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
tx_be_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
tx_be_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
tx_be_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
rx_ax_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
rx_ax_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
HTT_PDEV_PUNCTURE_STATS_TLV:
mac_id = 0
rx_be_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
rx_be_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
rx_be_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
rx_be_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218035711.2573584-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request Address Search Table(AST) entries stats
from firmware through HTT stats type 41. These stats give AST entries
related information such as software peer id, MAC address, pdev id,
vdev, id, next hop, etc.
Sample output:
-------------
echo 41 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_AST_ENTRY_TLV:
ast_index = 10
mac_addr = 00:00:00:01:00:00
sw_peer_id = 0
pdev_id = 3
vdev_id = 255
next_hop = 0
mcast = 0
monitor_direct = 0
mesh_sta = 0
mec = 0
intra_bss = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218035711.2573584-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request OFDMA stats of transmit buffers from firmware through
HTT stats type 32. These stats give information about NDPA, NDP, BRP and
steering mechanisms.
Note: WCN7850 firmware version -
WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 does not
support HTT stats type 32.
Sample output:
-------------
echo 32 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TXBF_OFDMA_AX_NDPA_STATS_TLV:
ax_ofdma_ndpa_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_ndpa_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_NDP_STATS_TLV:
ax_ofdma_ndp_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_ndp_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_BRP_STATS_TLV:
ax_ofdma_brpoll_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_brpoll_tied = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_STEER_STATS_TLV:
ax_ofdma_num_ppdu_steer = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
ax_ofdma_num_usrs_prefetch = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0,
17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0
.....
HTT_TXBF_OFDMA_AX_STEER_MPDU_STATS_TLV:
rbo_steer_mpdus_tried = 0
rbo_steer_mpdus_failed = 0
sifs_steer_mpdus_tried = 0
sifs_steer_mpdus_failed = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org>
Link: https://patch.msgid.link/20241128110949.3672364-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request transmit rate buffer stats from firmware through
HTT stats type 31. These stats give information such as MCS, NSS and
bandwidth of transmit and input buffer.
Sample output:
-------------
echo 31 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_STATS_PDEV_TX_RATE_TXBF_STATS:
Legacy OFDM Rates: 6 Mbps: 0, 9 Mbps: 0, 12 Mbps: 0, 18 Mbps: 0
24 Mbps: 0, 36 Mbps: 0, 48 Mbps: 0, 54 Mbps: 0
tx_ol_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_ibf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_txbf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0
tx_ol_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_ibf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_txbf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0
tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
half_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
quarter_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0
HTT_STATS_PDEV_TXBF_FLAG_RETURN_STATS:
TXBF_reason_code_stats: 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jjohnson@kernel.org>
Link: https://patch.msgid.link/20241128110949.3672364-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- a handful of selftest fixes
- fix a memory leak in relocation processing during module loading
- avoid sleeping in die()
- fix kprobe instruction slot address calculations
- fix DT node reference leak in SBI idle probing
- avoid initializing out of bounds pages on sparse vmemmap systems with
a gap at the start of their physical memory map
- fix backtracing through exceptions
- _Q_PENDING_LOOPS is now defined whenever QUEUED_SPINLOCKS=y
- local labels in entry.S are now marked with ".L", which prevents them
from trashing backtraces
- a handful of fixes for SBI-based performance counters
* tag 'riscv-for-linus-6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
drivers/perf: riscv: Do not allow invalid raw event config
drivers/perf: riscv: Return error for default case
drivers/perf: riscv: Fix Platform firmware event data
tools: selftests: riscv: Add test count for vstate_prctl
tools: selftests: riscv: Add pass message for v_initval_nolibc
riscv: use local label names instead of global ones in assembly
riscv: qspinlock: Fixup _Q_PENDING_LOOPS definition
riscv: stacktrace: fix backtracing through exceptions
riscv: mm: Fix the out of bound issue of vmemmap address
cpuidle: riscv-sbi: fix device node release in early exit of for_each_possible_cpu
riscv: kprobes: Fix incorrect address calculation
riscv: Fix sleeping in invalid context in die()
riscv: module: remove relocation_head rel_entry member allocation
riscv: selftests: Fix warnings pointer masking test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Ilpo Järvinen:
"Fixes and new HW support:
- amd/pmc: Match IRQ1 wakeup disable with the enable on i8042 side
- intel: power-domains: Clearwater Forest support
- intel/pmc: Skip SSRAM setup when no additional devices are present
- ISST: Clearwater Forest support"
* tag 'platform-drivers-x86-v6.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: intel/pmc: Fix ioremap() of bad address
platform/x86: ISST: Add Clearwater Forest to support list
platform/x86/intel: power-domains: Add Clearwater Forest support
platform/x86/amd/pmc: Only disable IRQ1 wakeup where i8042 actually enabled it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"There's one small fix for real HW - gpio-loongson.
The rest concern two virtual testing drivers in which some issues were
recently found and addressed:
- fix resource leaks in error path in gpio-virtuser (and one
consistent memory leak triggered on every device removal))
- fix the use-case of having multiple con_ids in a lookup table in
gpio-virtuser which has never worked (despite being advertised)
- don't allow rmdir() on configfs directories when they are in use in
gpio-sim and gpio-virtuser
- fix register offsets in gpio-loongson-64"
* tag 'gpio-fixes-for-v6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: loongson: Fix Loongson-2K2000 ACPI GPIO register offset
gpio: sim: lock up configfs that an instantiated device depends on
gpio: virtuser: lock up configfs that an instantiated device depends on
gpio: virtuser: fix handling of multiple conn_ids in lookup table
gpio: virtuser: fix missing lookup table cleanups
|
