summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2022-10-28soundwire: qcom: reinit broadcast completionSrinivas Kandagatla
For some reason we never reinit the broadcast completion, there is a danger that broadcast commands could be treated as completed by driver from previous complete status. Fix this by reinitializing the completion before sending a broadcast command. Fixes: ddea6cf7b619 ("soundwire: qcom: update register read/write routine") Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221026110210.6575-2-srinivas.kandagatla@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-10-28soundwire: intel: Initialize clock stop timeoutSjoerd Simons
The bus->clk_stop_timeout member is only initialized to a non-zero value during the codec driver probe. This can lead to corner cases where this value remains pegged at zero when the bus suspends, which results in an endless loop in sdw_bus_wait_for_clk_prep_deprep(). Corner cases include configurations with no codecs described in the firmware, or delays in probing codec drivers. Initializing the default timeout to the smallest non-zero value avoid this problem and allows for the existing logic to be preserved: the bus->clk_stop_timeout is set as the maximum required by all codecs connected on the bus. Fixes: 1f2dcf3a154ac ("soundwire: intel: set dev_num_ida_min") Signed-off-by: Sjoerd Simons <sjoerd@collabora.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Chao Song <chao.song@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-10-28drm/vc4: Make sure we don't end up with a core clock too highMaxime Ripard
Following the clock rate range improvements to the clock framework, trying to set a disjoint range on a clock will now result in an error. Thus, we can't set a minimum rate higher than the maximum reported by the firmware, or clk_set_min_rate() will fail. Thus we need to clamp the rate we are about to ask for to the maximum rate possible on that clock. Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-7-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28drm/vc4: hdmi: Add more checks for 4k resolutionsDom Cobley
At least the 4096x2160@60Hz mode requires some overclocking that isn't available by default, even if hdmi_enable_4kp60 is enabled. Let's add some logic to detect whether we can satisfy the core clock requirements for that mode, and prevent it from being used otherwise. Signed-off-by: Dom Cobley <popcornmix@gmail.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-6-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28drm/vc4: hdmi: Rework hdmi_enable_4kp60 detection codeMaxime Ripard
In order to support higher HDMI frequencies, users have to set the hdmi_enable_4kp60 parameter in their config.txt file. This will have the side-effect of raising the maximum of the core clock, tied to the HVS, and managed by the HVS driver. However, we are querying this in the HDMI driver by poking into the HVS structure to get our struct clk handle. Let's make this part of the HVS bind implementation to have all the core clock related setup in the same place. Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-5-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28drm/vc4: hdmi: Fix hdmi_enable_4kp60 detectionMaxime Ripard
In order to support higher HDMI frequencies, users have to set the hdmi_enable_4kp60 parameter in their config.txt file. We were detecting this so far by calling clk_round_rate() on the core clock with the frequency we're supposed to run at when one of those modes is enabled. Whether or not the parameter was enabled could then be inferred by the returned rate since the maximum clock rate reported by the firmware was one of the side effect of setting that parameter. However, the recent clock rework we did changed what clk_round_rate() was returning to always return the minimum allowed, and thus this test wasn't reliable anymore. Let's use the new clk_get_max_rate() function to reliably determine the maximum rate allowed on that clock and fix the 4k@60Hz output. Fixes: e9d6cea2af1c ("clk: bcm: rpi: Run some clocks at the minimum rate allowed") Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-4-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28firmware: raspberrypi: Provide a helper to query a clock max rateMaxime Ripard
The firmware allows to query for its clocks the operating range of a given clock. We'll need this for some drivers (KMS, in particular) to infer the state of some configuration options, so let's create a function to do so. Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-3-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28firmware: raspberrypi: Move the clock IDs to the firmware headerMaxime Ripard
We'll need the clock IDs in more drivers than just the clock driver from now on, so let's move them in the firmware header. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-2-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28firmware: raspberrypi: Introduce rpi_firmware_find_node()Maxime Ripard
A significant number of RaspberryPi drivers using the firmware don't have a phandle to it, so end up scanning the device tree to find a node with the firmware compatible. That code is duplicated everywhere, so let's introduce a helper instead. Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-1-fe9e7ac8b111@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-28net: emaclite: update reset_lock member documentationRadhey Shyam Pandey
Instead of generic description, mention what reset_lock actually protects i.e. lock to serialize xmit and tx_timeout execution. Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-28net: dsa: Fix possible memory leaks in dsa_loop_init()Chen Zhongjin
kmemleak reported memory leaks in dsa_loop_init(): kmemleak: 12 new suspected memory leaks unreferenced object 0xffff8880138ce000 (size 2048): comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s) backtrace: [<000000006a94f1d5>] kmalloc_trace+0x26/0x60 [<00000000a9c44622>] phy_device_create+0x5d/0x970 [<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0 [<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0 [<000000008a834798>] fixed_phy_register+0x84/0xb0 [<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop] ... There are two reasons for memleak in dsa_loop_init(). First, fixed_phy_register() create and register phy_device: fixed_phy_register() get_phy_device() phy_device_create() # freed by phy_device_free() phy_device_register() # freed by phy_device_remove() But fixed_phy_unregister() only calls phy_device_remove(). So the memory allocated in phy_device_create() is leaked. Second, when mdio_driver_register() fail in dsa_loop_init(), it just returns and there is no cleanup for phydevs. Fix the problems by catching the error of mdio_driver_register() in dsa_loop_init(), then calling both fixed_phy_unregister() and phy_device_free() to release phydevs. Also add a function for phydevs cleanup to avoid duplacate. Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-28Merge tag 'drm-misc-next-2022-10-27' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 6.2: UAPI Changes: Cross-subsystem Changes: Core Changes: - connector: Send hotplug event on cleanup - edid: logging/debug improvements - plane_helper: Improve tests Driver Changes: - bridge: - it6505: Synchronization improvements - panel: - panel-edp: Add INX N116BGE-EA2 C2 and C4 support. - nouveau: Fix page-fault handling - vmwgfx: fb and cursor refactoring, convert to generic hashtable Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20221027073407.c2tlaczvzjrnzazi@houat
2022-10-28Merge tag 'drm-misc-fixes-2022-10-27' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes drm-misc-fixes for v6.1-rc3: - Fix HPD on bridge/ps8640. - Stop leaking fences when killing a sched entity. - Avoid uninitialized read in aperture_remove_conflicting_pci_device() Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ed24cbd2-2bcb-d2c2-46ed-9d8ea9615879@linux.intel.com
2022-10-28Merge tag 'drm-intel-fixes-2022-10-27-1' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes - Extend Wa_1607297627 to Alderlake-P (José Roberto de Souza) - Keep PCI autosuspend control 'on' by default on all dGPU (Anshuman Gupta) - Reset frl trained flag before restarting FRL training (Ankit Nautiyal) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/Y1o+teE2Z11pT1MN@tursulin-desk
2022-10-27clk: qcom: Update the force mem core bit for GPU clocksTaniya Das
There are few GPU clocks which are powering up the memories and thus enable the FORCE_MEM_PERIPH always for these clocks to force the periph_on signal to remain active during halt state of the clock. Fixes: a3cc092196ef ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280") Fixes: 3e0f01d6c7e7 ("clk: qcom: Add graphics clock controller driver for SC7280") Signed-off-by: Taniya Das <quic_tdas@quicinc.com> Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com> Link: https://lore.kernel.org/r/1666159535-6447-1-git-send-email-quic_c_skakit@quicinc.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-10-27clk: Initialize max_rate in struct clk_rate_requestMaxime Ripard
Since commit b46fd8dbe8ad ("clk: Zero the clk_rate_request structure"), the clk_core_init_rate_req() function clears the struct clk_rate_request passed as argument. However, the default value for max_rate isn't 0 but ULONG_MAX, and we end up creating a clk_rate_request instance where the maximum rate is 0. Let's initialize max_rate to ULONG_MAX properly. Fixes: b46fd8dbe8ad ("clk: Zero the clk_rate_request structure") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v1-3-f3ef80518140@cerno.tech Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-10-27clk: Initialize the clk_rate_request even if clk_core is NULLMaxime Ripard
Since commit c35e84b09776 ("clk: Introduce clk_hw_init_rate_request()"), users that used to initialize their clk_rate_request by initializing their local structure now rely on clk_hw_init_rate_request(). This function is backed by clk_core_init_rate_req(), which will skip the initialization if either the pointer to struct clk_core or to struct clk_rate_request are NULL. However, the core->parent pointer might be NULL because the clock is orphan, and we will thus end up with our local struct clk_rate_request left untouched. And since clk_hw_init_rate_request() doesn't return an error, we will then call a determine_rate variant with that unitialized structure. In order to avoid this, let's clear our clk_rate_request if the pointer to it is valid but the pointer to struct clk_core isn't. Fixes: c35e84b09776 ("clk: Introduce clk_hw_init_rate_request()") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v1-2-f3ef80518140@cerno.tech Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-10-27clk: Remove WARN_ON NULL parent in clk_core_init_rate_req()Maxime Ripard
If a clock has CLK_SET_RATE_PARENT, but core->parent is NULL (most likely because it's orphan), callers of clk_core_init_rate_req() will blindly call this function leading to a very verbose warning. Since it's a fairly common situation, let's just remove the WARN_ON but keep the check that prevents us from dereferencing the pointer. Interestingly, it fixes a regression on the Mediatek MT8195 where the GPU would stall during a clk_set_rate for its main clock. We couldn't come up with a proper explanation since the condition is essentially the same. It was then assumed that it could be timing related since printing the warning stacktrace takes a while, but we couldn't replicate the failure by using fairly large (10ms) mdelays. Fixes: 262ca38f4b6e ("clk: Stop forwarding clk_rate_requests to the parent") Reported-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v1-1-f3ef80518140@cerno.tech Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-10-27Merge tag 'net-6.1-rc3-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from 802.15.4 (Zigbee et al). Current release - regressions: - ipa: fix bugs in the register conversion for IPA v3.1 and v3.5.1 Current release - new code bugs: - mptcp: fix abba deadlock on fastopen - eth: stmmac: rk3588: allow multiple gmac controllers in one system Previous releases - regressions: - ip: rework the fix for dflt addr selection for connected nexthop - net: couple more fixes for misinterpreting bits in struct page after the signature was added Previous releases - always broken: - ipv6: ensure sane device mtu in tunnels - openvswitch: switch from WARN to pr_warn on a user-triggerable path - ethtool: eeprom: fix null-deref on genl_info in dump - ieee802154: more return code fixes for corner cases in dgram_sendmsg - mac802154: fix link-quality-indicator recording - eth: mlx5: fixes for IPsec, PTP timestamps, OvS and conntrack offload - eth: fec: limit register access on i.MX6UL - eth: bcm4908_enet: update TX stats after actual transmission - can: rcar_canfd: improve IRQ handling for RZ/G2L Misc: - genetlink: piggy back on the newly added resv_op_start to enforce more sanity checks on new commands" * tag 'net-6.1-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits) net: enetc: survive memory pressure without crashing kcm: do not sense pfmemalloc status in kcm_sendpage() net: do not sense pfmemalloc status in skb_append_pagefrags() net/mlx5e: Fix macsec sci endianness at rx sa update net/mlx5e: Fix wrong bitwise comparison usage in macsec_fs_rx_add_rule function net/mlx5e: Fix macsec rx security association (SA) update/delete net/mlx5e: Fix macsec coverity issue at rx sa update net/mlx5: Fix crash during sync firmware reset net/mlx5: Update fw fatal reporter state on PCI handlers successful recover net/mlx5e: TC, Fix cloned flow attr instance dests are not zeroed net/mlx5e: TC, Reject forwarding from internal port to internal port net/mlx5: Fix possible use-after-free in async command interface net/mlx5: ASO, Create the ASO SQ with the correct timestamp format net/mlx5e: Update restore chain id for slow path packets net/mlx5e: Extend SKB room check to include PTP-SQ net/mlx5: DR, Fix matcher disconnect error flow net/mlx5: Wait for firmware to enable CRS before pci_restore_state net/mlx5e: Do not increment ESN when updating IPsec ESN state netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir failed netdevsim: fix memory leak in nsim_drv_probe() when nsim_dev_resources_register() failed ...
2022-10-27drm/i915/perf: Enable OA for DG2Umesh Nerlige Ramappa
OA was disabled for DG2 as support was missing. Enable it back now. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-17-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: complete programming whitelisting for XEHPSDVLionel Landwerlin
We have an additional register to select which slices contribute to OAG/OAG counter increments. Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-16-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/guc: Support OA when Wa_16011777198 is enabledVinay Belgaumkar
On DG2, a w/a resets RCS/CCS before it goes into RC6. This breaks OA since OA does not expect engine resets during its use. Fix it by disabling RC6. v2: (Ashutosh) - Bring back slpc_unset_param helper - Update commit msg - Use with_intel_runtime_pm helper for set/unset v3: (Ashutosh) - Just use intel_uc_uses_guc_rc Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com> Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-15-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Save/restore EU flex counters across resetUmesh Nerlige Ramappa
If a drm client is killed, then hw contexts used by the client are reset immediately. This reset clears the EU flex counter configuration. If an OA use case is running in parallel, it would start seeing zeroed eu counter values following the reset even if the drm client is restarted. Save/restore the EU flex counter config so that the EU counters can be monitored continuously across resets. v2: - Save/restore eu flex config only for gen12, as for pre-gen12, these are saved and restored in the context image. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-14-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Apply Wa_18013179988Umesh Nerlige Ramappa
OA reports in the OA buffer contain an OA timestamp field that helps user calculate delta between 2 OA reports. The calculation relies on the CS timestamp frequency to convert the timestamp value to nanoseconds. The CS timestamp frequency is a function of the CTC_SHIFT value in RPM_CONFIG0. In DG2, OA unit assumes that the CTC_SHIFT is 3, instead of using the actual value from RPM_CONFIG0. At the user level, this results in an error in calculating delta between 2 OA reports since the OA timestamp is not shifted in the same manner as CS timestamp. Also the periodicity of the reports is different from what the user configured because of mismatch in the CS and OA frequencies. The issue also affects MI_REPORT_PERF_COUNT command. To resolve this, return actual OA timestamp frequency to the user in i915_getparam_ioctl, so that user can calculate the right OA exponent as well as interpret the reports correctly. MR: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/18893 v2: - Use REG_FIELD_GET (Ashutosh) - Update commit msg Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-13-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Add Wa_1508761755:dg2Umesh Nerlige Ramappa
Disable Clock gating in EU when gathering the events so that EU events are not lost. v2: Fix checkpatch issues v3: User MCR helpers to write to MC reg v4: Indent correctly (checkpatch) Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-12-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Store a pointer to oa_format in oa_bufferUmesh Nerlige Ramappa
DG2 introduces OA reports with 64 bit report header fields. Perf OA would need more information about the OA format in order to process such reports. Store all OA format info in oa_buffer instead of just the size and format-id. v2: Drop format_size variable (Ashutosh) Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-11-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Use gt-specific ggtt for OA and noa-wait buffersUmesh Nerlige Ramappa
User passes uabi engine class and instance to the perf OA interface. Use gt corresponding to the engine to pin the buffers to the right ggtt. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-10-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Replace gt->perf.lock with stream->lock for file opsUmesh Nerlige Ramappa
With multi-gt, user can access multiple OA buffers concurrently. Use stream->lock instead of gt->perf.lock to serialize file operations. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-9-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Move gt-specific data from i915->perf to gt->perfUmesh Nerlige Ramappa
Make perf part of gt as the OAG buffer is specific to a gt. The refactor eventually simplifies programming the right OA buffer and the right HW registers when supporting multiple gts. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-8-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Simply use stream->ctxUmesh Nerlige Ramappa
Earlier code used exclusive_stream to check for user passed context. Simplify this by accessing stream->ctx. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-7-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Enable bytes per clock reporting in OAUmesh Nerlige Ramappa
XEHPSDV and DG2 provide a way to configure bytes per clock vs commands per clock reporting. Enable bytes per clock setting on enabling OA. Bspec: 51762 Bspec: 52201 v2: - Fix commit msg (Ashutosh) - Fix checkpatch issues v3: - s/commands/bytes/ in code comment and commmit msg Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-6-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Determine gen12 oa ctx offset at runtimeUmesh Nerlige Ramappa
Some SKUs of same gen12 platform may have different oactxctrl offsets. For gen12, determine oactxctrl offsets at runtime. v2: (Lionel) - Move MI definitions to intel_gpu_commands.h - Ensure __find_reg_in_lri does read past context image size v3: (Ashutosh) - Drop unnecessary use of double underscores - fix find_reg_in_lri - Return error if oa context offset is U32_MAX - Error out if oa_ctx_ctrl_offset does not find offset v4: (Ashutosh) - Warn on odd MI LRI_LEN - Remove unnecessary check for valid_oactxctrl_offset - Drop valid_oactxctrl_offset macro v5: Drop unrelated comment Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-5-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Fix noa wait predication for DG2Umesh Nerlige Ramappa
Predication for batch buffer commands changed in XEHPSDV. MI_BATCH_BUFFER_START predicates based on MI_SET_PREDICATE_RESULT register. The MI_SET_PREDICATE_RESULT register can only be modified with MI_SET_PREDICATE command. When configured, the MI_SET_PREDICATE command sets MI_SET_PREDICATE_RESULT based on bit 0 of MI_PREDICATE_RESULT_2. Use this to configure predication in noa_wait. Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-4-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Add 32-bit OAG and OAR formats for DG2Umesh Nerlige Ramappa
Add new OA formats for DG2. MR: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/18893 v2: - Update commit title (Ashutosh) - Coding style fixes (Lionel) - 64 bit OA formats need UMD changes in GPUvis, drop for now and send in a separate series with UMD changes v3: - Update commit message to drop 64 bit related description Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> #1 Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-3-umesh.nerlige.ramappa@intel.com
2022-10-27drm/i915/perf: Fix OA filtering logic for GuC modeUmesh Nerlige Ramappa
With GuC mode of submission, GuC is in control of defining the context id field that is part of the OA reports. To filter reports, UMD and KMD must know what sw context id was chosen by GuC. There is not interface between KMD and GuC to determine this, so read the upper-dword of EXECLIST_STATUS to filter/squash OA reports for the specific context. v2: Explain guc id stealing w.r.t OA use case Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026222102.5526-2-umesh.nerlige.ramappa@intel.com
2022-10-27Merge tag 'media/v6.1-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Pull media fixes from Mauro Carvalho Chehab: "A bunch of patches addressing issues in the vivid driver and adding new checks in V4L2 to validate the input parameters from some ioctls" * tag 'media/v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: media: vivid.rst: loop_video is set on the capture devnode media: vivid: set num_in/outputs to 0 if not supported media: vivid: drop GFP_DMA32 media: vivid: fix control handler mutex deadlock media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced' media: v4l2-dv-timings: add sanity checks for blanking values media: vivid: dev->bitmap_cap wasn't freed in all cases media: vivid: s_fbuf: add more sanity checks
2022-10-27drm/amd/display: Modify mismatched function nameJiapeng Chong
No functional modification involved. drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:615: warning: expecting prototype for setup_subvp_dmub_command(). Prototype was for populate_subvp_cmd_pipe_info() instead. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2587 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amd/display: make wake_up_aux_channel staticJiapeng Chong
This symbol is not used outside of dc_link_dp.c, so marks it static. drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:5230:16: warning: no previous prototype for function 'wake_up_aux_channel'. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2581 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdkfd: Cleanup kfd_dev structMukul Joshi
Cleanup kfd_dev struct by removing ddev and pdev as both drm_device and pci_dev can be fetched from amdgpu_device. Signed-off-by: Mukul Joshi <mukul.joshi@amd.com> Tested-by: Amber Lin <Amber.Lin@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdgpu: disable GFXOFF during compute for GFX11Graham Sider
Temporary workaround to fix issues observed in some compute applications when GFXOFF is enabled on GFX11. Signed-off-by: Graham Sider <Graham.Sider@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amd: Fail the suspend if resources can't be evictedMario Limonciello
If a system does not have swap and memory is under 100% usage, amdgpu will fail to evict resources. Currently the suspend carries on proceeding to reset the GPU: ``` [drm] evicting device resources failed [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <vcn_v3_0> failed -12 [drm] free PSP TMR buffer [TTM] Failed allocating page table [drm] evicting device resources failed amdgpu 0000:03:00.0: amdgpu: MODE1 reset amdgpu 0000:03:00.0: amdgpu: GPU mode1 reset amdgpu 0000:03:00.0: amdgpu: GPU smu mode1 reset ``` At this point if the suspend actually succeeded I think that amdgpu would have recovered because the GPU would have power cut off and restored. However the kernel fails to continue the suspend from the memory pressure and amdgpu fails to run the "resume" from the aborted suspend. ``` ACPI: PM: Preparing to enter system sleep state S3 SLUB: Unable to allocate memory on node -1, gfp=0xdc0(GFP_KERNEL|__GFP_ZERO) cache: Acpi-State, object size: 80, buffer size: 80, default order: 0, min order: 0 node 0: slabs: 22, objs: 1122, free: 0 ACPI Error: AE_NO_MEMORY, Could not update object reference count (20210730/utdelete-651) [drm:psp_hw_start [amdgpu]] *ERROR* PSP load kdb failed! [drm:psp_resume [amdgpu]] *ERROR* PSP resume failed [drm:amdgpu_device_fw_loading [amdgpu]] *ERROR* resume of IP block <psp> failed -62 amdgpu 0000:03:00.0: amdgpu: amdgpu_device_ip_resume failed (-62). PM: dpm_run_callback(): pci_pm_resume+0x0/0x100 returns -62 amdgpu 0000:03:00.0: PM: failed to resume async: error -62 ``` To avoid this series of unfortunate events, fail amdgpu's suspend when the memory eviction fails. This will let the system gracefully recover and the user can try suspend again when the memory pressure is relieved. Reported-by: post@davidak.de Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2223 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27Revert "drm/amd/display: Limit max DSC target bpp for specific monitors"Hamza Mahfooz
This reverts commit 55eea8ef98641f6e1e1c202bd3a49a57c1dd4059. This quirk is now handled in the DRM core, so we can drop all of the internal code that was added to handle it. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amd/display: use max_dsc_bpp in amdgpu_dmHamza Mahfooz
Since, the quirk is handled in the DRM core now, we can use that value instead of the internal value. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/edid: add a quirk for two LG monitors to get them to work on 10bpcHamza Mahfooz
The LG 27GP950 and LG 27GN950 have visible display corruption when trying to use 10bpc modes. So, to fix this, cap their maximum DSC target bitrate to 15bpp. Suggested-by: Roman Li <roman.li@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdgpu: Add EEPROM I2C address support for ip discoveryCandice Li
1. Update EEPROM_I2C_MADDR_SMU_13_0_0 to EEPROM_I2C_MADDR_54H 2. Add EEPROM I2C address support for smu v13_0_0 and v13_0_10. Signed-off-by: Candice Li <candice.li@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdgpu: Update ras eeprom support for smu v13_0_0 and v13_0_10Candice Li
Enable RAS EEPROM support for smu v13_0_0 and v13_0_10. Signed-off-by: Candice Li <candice.li@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdgpu: Optimize TA load/unload/invoke debugfs interfacesCandice Li
1. Add a function pointer structure ta_funcs to psp context 2. Make the interfaces generic to all TAs 3. Leverage exisitng TA context and remove unused functions 4. Fix return code bugs v2: Add comments for ta funcs macros and correct typo Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Candice Li <candice.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdgpu: Optimize RAS TA initialization and TA unload funcsCandice Li
1. Save TA unload psp response status 2. Add RAS TA loading status check for initializaiton 3. Drop RAS context teardown to allow RAS TA to be reloaded Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Candice Li <candice.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amdkfd: Fix NULL pointer dereference in svm_migrate_to_ram()Yang Li
./drivers/gpu/drm/amd/amdkfd/kfd_migrate.c:985:58-62: ERROR: p is NULL but dereferenced. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2549 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-10-27drm/amd/display: prevent memory leakgehao
In dce6(0,1,4)_create_resource_pool and dce80_create_resource_pool the allocated memory should be released if construct pool fails. Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: gehao <gehao@kylinos.cn> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
generated by cgit (git 2.34.1) at 2025-10-01 23:12:09 +0000