| Age | Commit message (Collapse) | Author |
|---|
|
The _HPX Type 3 Setting Record is intended to be more generic and allow
configuration of settings not possible with Type 2 records. For example,
firmware could ensure that the completion timeout value is set accordingly
throughout the PCI tree.
Implement support for _HPX Type 3 Setting Records, which were added in the
ACPI 6.3 spec.
Link: https://lore.kernel.org/lkml/20190208162414.3996-4-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We used to first parse all the _HPP and _HPX tables before using the
information to program registers of PCIe devices. Up through HPX Type 2,
there was only one structure of each type, so we could cheat and store it
on the stack.
With HPX Type 3 we get an arbitrary number of entries, so the above model
doesn't scale that well. Instead of parsing all tables at once, parse and
program each entry separately. For _HPP and _HPX Types 0 through 2, this
is functionally equivalent. The change enables the upcoming _HPX Type 3 to
integrate more easily.
Link: https://lore.kernel.org/lkml/20190208162414.3996-3-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: fix build errors]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_get_hp_params() is only used within drivers/pci, and there is no reason
to make it available outside of the PCI core, so stop exporting it.
Link: https://lore.kernel.org/lkml/20190208162414.3996-2-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
|
|
If the bandwidth notification interrupt is left unmasked when entering
suspend to idle, it triggers immediately bringing the system back to
working state.
To keep that from happening, disable the interrupt when entering system
sleep and enable it again during resume.
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.
It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally. Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.
Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.
Fixes: 52eabba5bcdb ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
|
|
The Switchtec devices supports two PCIe Function Frameworks (PFFs) per
upstream port (one for the port itself and one for the management endoint),
and each PFF may have up to 255 ports. Previously the driver only
supported 48 of those ports, and the SWITCHTEC_IOCTL_EVENT_SUMMARY ioctl
only returned information about those 48.
Increase SWITCHTEC_MAX_PFF_CSR from 48 to 255 so the driver supports all
255 possible ports.
Rename SWITCHTEC_IOCTL_EVENT_SUMMARY and associated struct
switchtec_ioctl_event_summary to SWITCHTEC_IOCTL_EVENT_SUMMARY_LEGACY and
switchtec_ioctl_event_summary_legacy with so existing applications work
unchanged, supporting up to 48 ports.
Add replacement SWITCHTEC_IOCTL_EVENT_SUMMARY and struct
switchtec_ioctl_event_summary that new and recompiled applications support
up to 255 ports.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
|
|
pci_request_region_exclusive() was introduced with commit e8de1481fd71
("resource: allow MMIO exclusivity for device drivers") in 2.6.29 which
was released 2008.
It never had an in tree user since then, so after 11 years later let's
remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The "Enhanced Allocation (EA) for Memory and I/O Resources" ECN, approved
23 October 2014, sec 6.9.1.2, specifies a second DW in the capability for
type 1 (bridge) functions to describe fixed secondary and subordinate bus
numbers. This ECN was included in the PCIe r4.0 spec, but sec 6.9.1.2 was
omitted, presumably by mistake.
Read fixed bus numbers from the EA capability for bridges.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
[bhelgaas: add pci_ea_fixed_busnrs() return value]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Certain platforms like TI's AM654 do not have aseparate address space for
dbi2 instead they are accessed using the same address space as dbi
with some configuration bit set. In order to support such platforms,
add callbacks for accessing dbi2 address space.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
commit beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler") while
adding MSI-X callback handler, introduced dw_pcie_ep_find_capability()
and __dw_pcie_ep_find_next_cap() for finding the MSI and MSIX capability.
However if MSI or MSIX capability is the last capability (i.e there are
no additional items in the capabilities list and the Next Capability
Pointer is set to '0'), __dw_pcie_ep_find_next_cap will return '0'
even though MSI or MSIX capability may be present because of
incorrect ordering of the "next_cap_ptr" check. Fix it.
Fixes: beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Add const qualifier to struct dw_pcie_ep_ops member of
struct dw_pcie_ep.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.
Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.
Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.
Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().
[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
Controller Databook version 4.90a
[2] http://www.ti.com/lit/ug/spruid7c/spruid7c.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
PCIe in TI's AM654 devices is by default configured to work in GEN3 mode.
However PCIe does not work reliably in GEN3 mode because of SERDES
configuration.
Add support to set the link speed to GEN1, GEN2 or GEN3 based on
"max-link-speed" DT property with GEN2 as the default speed if
"max-link-speed" is absent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
of_pci_get_max_link_speed() is built only if CONFIG_PCI is enabled.
Make of_pci_get_max_link_speed() to be also used by PCI Endpoint
controllers with just CONFIG_PCI_ENDPOINT enabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
SERDES connected to the PCIe controller in AM654 requires
power on reset enable (POR_EN) to be set in the SERDES. The
SERDES driver sets POR_EN in the reset ops and it has to be
invoked before init or enable ops. In order for SERDES driver
to set POR_EN, invoke the phy_reset() API in pci-keystone driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Add PCIe RC support for AM654x Platforms in pci-keystone.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Synopsys designware version >= 4.80 uses a separate register space
for programming ATU. The current code identifies if there exists a
separate register space by accessing the register address of ATUs
in designware version < 4.80. Accessing this address results in
abort in the case of K2G.
Fix it here by adding "version" member to struct dw_pcie. This should be
set by platform specific drivers and designware core will use it to
identify if the platform has a separate ATU space. For platforms which
have not populated the version member, the old method of identification
will still be used.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
iatu_unroll_enabled flag is set only for Designware in host mode.
However iATU unroll can be applicable for endpoint mode too. Set
iatu_unroll_enabled flag in dw_pcie_setup() which is common for
both host mode and endpoint mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Explicitly set the PCIe mode to BOOTCFG_DEVCFG instead of always
relying on the default values. This is required when EP mode has to
be explicitly written to BOOTCFG_DEVCFG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Move platform_get_resource() calls for resources that are applicable to
both host and endpoint mode (ie "dbics" and "app") from
ks_add_pcie_port() to the probe() callback, in preparation for adding
endpoint support to pci-keystone driver.
No functional change intended.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Commit 60ed982a4e78 ("PCI/AER: Move internal declarations to
drivers/pci/pci.h") changed pci_aer_init() to return "void", but didn't
change the stub for when CONFIG_PCIEAER isn't enabled. Change the stub to
match.
Fixes: 60ed982a4e78 ("PCI/AER: Move internal declarations to drivers/pci/pci.h")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.19+
|
|
Set the "untrusted" attribute to any PCIe port that has an
"external-facing" device tree property. Any device downstream of this port
will inherit the attribute and have only the strictest IOMMU protection.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521
Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org
Fixes: 9b44b0b09dec ("PCI: Mark AMD Stoney GPU ATS as broken")
Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
CC: stable@vger.kernel.org
|
|
Use platform_get_resource_byname() instead of platform_get_resource()
which uses an index to get memory resources. While at that get the memory
resource defined specifically for configuration space instead of
deriving the configuration space address from dbics address space.
Since the pci-keystone driver has never worked in the mainline kernel,
DT backward compatibility is not an issue.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
No functional change. Instead of having two functions
ks_pcie_add_pcie_port() and ks_pcie_dw_host_init() for initializing
host, have a single function to perform all the host initialization.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
pci-keystone driver uses irq_of_parse_and_map() to get irq number of
error_irq.
Use platform_get_irq() instead and move platform_get_irq() and
request_irq() of error_irq from ks_pcie_add_pcie_port to ks_pcie_probe
since error_irq is common to both RC mode and EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Add start_link()/stop_link() dw_pcie_ops and invoke ks_pcie_start_link()
directly from host_init. start_link()/stop_link() ops are required for
adding EP mode support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Update the driver to use devm_clk_get_optional() to claim
optional clocks instead of devm_clk_get().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Honghui Zhang <honghui.zhang@mediatek.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Honghui Zhang <honghui.zhang@mediatek.com>
|
|
When allocating the slot structure we store a pointer to the associated
device_node. We really should be incrementing the reference count, so add
an of_node_get() during slot alloc and an of_node_put() during slot
dealloc.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Transform wait code to a "do {} while (time_before())" loop as recommended
by reviewer. No functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
|
|
Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No
functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
|
|
Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and
pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes
the PCIe feature bits, which prevents from using features such as hotplug
or AER on some systems, when booting with device tree. Make the
initialization code common.
Fixes: 02bfeb484230 ("PCI/portdrv: Simplify PCIe feature permission checking")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.17+
|
|
Platforms which populate msi_host_init() have their own MSI controller
logic. Writing to MSI control registers on platforms which do not use
Designware's MSI controller logic might have side effects.
To be safe, do not write to MSI control registers if the platform uses
its own MSI controller logic instead of Designware's MSI one.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Now that Keystone started using its own msi_irq_chip, remove
Keystone specific callback functions defined in dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Use Keystone specific msi_irq_chip to configure the MSI controller
logic in the PCIe keystone wrapper instead of using the default
Designware msi_irq chip (dw_pci_msi_bottom_irq_chip) with
callback functions for configuring the Keystone MSI controller.
This will help to remove Keystone specific callback functions
added in dw_pcie_host_ops.
Move the default msi_irq_chip assignment to dw_pcie_host_init since
platforms that doesn't use the default msi_irq_chip will assign
msi_irq_chip in the msi_host_init() callback.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Platforms using DesignWare IP use dw_pci_msi_bottom_irq_chip for
configuring the MSI controller logic within the DesignWare IP. However
certain platforms like Keystone (K2G) which uses DesignWare IP have
their own MSI controller logic. For handling such platforms,
the irqchip ops use msi_irq_ack(), msi_set_irq(), msi_clear_irq()
callback functions.
Add support to use different msi_irq_chip with default set to
dw_pci_msi_bottom_irq_chip. This is in preparation to get rid of
msi_irq_ack(), msi_set_irq(), msi_clear_irq() and other Keystone
specific dw_pcie_host_ops.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
ks_pcie_msi_irq_handler() invokes ks_pcie_handle_msi_irq() for handling
the interrupts.
Having two functions for handling the interrupt was used when keystone
PCIe driver was implemented using two files but with commit b492aca35c98
("PCI: keystone: Merge pci-keystone-dw.c and pci-keystone.c"), which
merged the keystone PCIe driver to use a single file, two functions for
handling the interrupt handler are not required.
Handle MSI interrupt in a single interrupt handler here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
ks_pcie_msi_irq_handler() uses 'virq' to get the IRQ number offset.
This offset is used to get the correct MSI_IRQ_STATUS register
corresponding to the IRQ line that raised the interrupt.
There is no guarantee that 'virq' assigned for consecutive hardware
IRQ will be contiguous and this might get us an incorrect IRQ number
offset.
Fix it here by using 'hwirq' to get the IRQ number offset. Since we
don't store the 'virq' numbers of all the IRQ numbers, stop checking
if irq count is greater than MAX_MSI_HOST_IRQS and remove
MAX_MSI_HOST_IRQS.
Link: https://lkml.kernel.org/r/bb081d21-7c03-0357-4294-7e92d95d838c@arm.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
ks_pcie_get_irq_controller_info() is used to configure both MSI and
legacy interrupt. This will prevent MSI or legacy interrupt specific
intializations. Add separate functions to configure MSI and legacy
interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
No functional change. Change both MSI interrupt and legacy interrupt
related macros to take an additional argument in order to return the
correct register offset.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
The IProc host controller has I/O memory windows allocated in
the AXI memory map that can be used to address PCI I/O memory
space.
Mapping from AXI memory windows to PCI outbound memory windows is
carried out in the host controller through OARR/OMAP registers pairs
that permit to define power of two region size AXI<->PCI mappings, the
smallest of which is 128MB.
Current code enables AXI memory window to PCI outbound memory window
mapping only for AXI windows matching one of the OARR/OMAP window sizes,
that are SoC dependent and the smallest of which is 128MB.
Some SoCs implementing the IProc host controller have a 32-bit AXI
memory window into PCI I/O memory space, eg:
Base address | Size
-----------------------------
(1) 0x42000000 | 0x2000000
(2) 0x400000000 | 0x80000000
but its size (32MB - (1) above) is smaller than the smallest AXI<->PCI
region size provided by OARR (128MB), so the current driver rejects
mappings for the 32-bit region making the IProc host controller driver
unusable on 32-bit systems.
However, there is no reason why the 32-bit I/O memory window cannot be
enabled by mapping it through an OARR/OMAP region bigger in size (ie
32-bit AXI window size is 32MB but can be mapped using a 128MB OARR/OMAP
region).
Allow outbound window configuration of I/O memory windows that
are smaller in size than the host controller OARR/OMAP region, so
that the 32-bit AXI memory window can actually be enabled,
making the IProc host controller operational on 32-bit systems.
Link: https://lore.kernel.org/linux-pci/1551415936-30174-3-git-send-email-srinath.mannam@broadcom.com/
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
|
|
The IPROC PCIe host controller implementation returns CFG_RETRY_STATUS
(0xffff0001) data when it receives a CRS completion, regardless of the
address of the read or the CRS Software Visibility Enable bit. As a
workaround the driver retries in software any read that returns
CFG_RETRY_STATUS even though, for reads of registers that are not Vendor
ID, the register value can correspond to CFG_RETRY_STATUS; this
situation would cause a timeout and failure of reading a valid register
value.
IPROC PCIe host controller PAXB v2 has a register to show config read
status flags like SC, UR, CRS and CA. Using this status flag,
an extra check is added to confirm the CRS using status flags before
reissuing a config read, fixing the issue.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
|
|
When we hot-remove a device, usually the host sends us a PCI_EJECT message,
and a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
When we execute the quick hot-add/hot-remove test, the host may not send
us the PCI_EJECT message if the guest has not fully finished the
initialization by sending the PCI_RESOURCES_ASSIGNED* message to the
host, so it's potentially unsafe to only depend on the
pci_destroy_slot() in hv_eject_device_work() because the code path
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
is not called in this case. Note: in this case, the host still sends the
guest a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
In the quick hot-add/hot-remove test, we can have such a race before
the code path
pci_devices_present_work()
-> new_pcichild_device()
adds the new device into the hbus->children list, we may have already
received the PCI_EJECT message, and since the tasklet handler
hv_pci_onchannelcallback()
may fail to find the "hpdev" by calling
get_pcichild_wslot(hbus, dev_message->wslot.slot)
hv_pci_eject_device() is not called; Later, by continuing execution
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
creates the slot and the PCI_BUS_RELATIONS message with
bus_rel->device_count == 0 removes the device from hbus->children, and
we end up being unable to remove the slot in
hv_pci_remove()
-> hv_pci_remove_slots()
Remove the slot in pci_devices_present_work() when the device
is removed to address this race.
pci_devices_present_work() and hv_eject_device_work() run in the
singled-threaded hbus->wq, so there is not a double-remove issue for the
slot.
We cannot offload hv_pci_eject_device() from hv_pci_onchannelcallback()
to the workqueue, because we need the hv_pci_onchannelcallback()
synchronously call hv_pci_eject_device() to poll the channel
ringbuffer to work around the "hangs in hv_compose_msi_msg()" issue
fixed in commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in
hv_compose_msi_msg()")
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: rewritten commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
|
|
When we unload the pci-hyperv host controller driver, the host does not
send us a PCI_EJECT message.
In this case we also need to make sure the sysfs PCI slot directory is
removed, otherwise a command on a slot file eg:
"cat /sys/bus/pci/slots/2/address"
will trigger a
"BUG: unable to handle kernel paging request"
and, if we unload/reload the driver several times we would end up with
stale slot entries in PCI slot directories in /sys/bus/pci/slots/
root@localhost:~# ls -rtl /sys/bus/pci/slots/
total 0
drwxr-xr-x 2 root root 0 Feb 7 10:49 2
drwxr-xr-x 2 root root 0 Feb 7 10:49 2-1
drwxr-xr-x 2 root root 0 Feb 7 10:51 2-2
Add the missing code to remove the PCI slot and fix the current
behaviour.
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: reformatted the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
|
|
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
|
|
Reestablish the PCIe link very early in the resume process in case it
went down to prevent PCI accesses from hanging the bus. Such accesses
can happen early in the PCI resume process, as early as the
SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the
driver resume_noirq() callback.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[lorenzo.pieralisi@arm.com: reformatted commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
|
