| Age | Commit message (Collapse) | Author |
|---|
|
If skb enqueue the qdisc, fq_skb_cb(skb)->time_to_send is changed which
is actually skb->cb, and IPCB(skb_in)->opt will be used in
__ip_options_echo. It is possible that memcpy is out of bounds and lead
to stack overflow.
We should clear skb->cb before ip_local_out or ip6_local_out.
v2:
1. clean the stack info
2. use IPCB/IP6CB instead of skb->cb
crash on stable-5.10(reproduce in kasan kernel).
Stack info:
[ 2203.651571] BUG: KASAN: stack-out-of-bounds in
__ip_options_echo+0x589/0x800
[ 2203.653327] Write of size 4 at addr ffff88811a388f27 by task
swapper/3/0
[ 2203.655460] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted
5.10.0-60.18.0.50.h856.kasan.eulerosv2r11.x86_64 #1
[ 2203.655466] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-20181220_000000-szxrtosci10000 04/01/2014
[ 2203.655475] Call Trace:
[ 2203.655481] <IRQ>
[ 2203.655501] dump_stack+0x9c/0xd3
[ 2203.655514] print_address_description.constprop.0+0x19/0x170
[ 2203.655530] __kasan_report.cold+0x6c/0x84
[ 2203.655586] kasan_report+0x3a/0x50
[ 2203.655594] check_memory_region+0xfd/0x1f0
[ 2203.655601] memcpy+0x39/0x60
[ 2203.655608] __ip_options_echo+0x589/0x800
[ 2203.655654] __icmp_send+0x59a/0x960
[ 2203.655755] nf_send_unreach+0x129/0x3d0 [nf_reject_ipv4]
[ 2203.655763] reject_tg+0x77/0x1bf [ipt_REJECT]
[ 2203.655772] ipt_do_table+0x691/0xa40 [ip_tables]
[ 2203.655821] nf_hook_slow+0x69/0x100
[ 2203.655828] __ip_local_out+0x21e/0x2b0
[ 2203.655857] ip_local_out+0x28/0x90
[ 2203.655868] ipvlan_process_v4_outbound+0x21e/0x260 [ipvlan]
[ 2203.655931] ipvlan_xmit_mode_l3+0x3bd/0x400 [ipvlan]
[ 2203.655967] ipvlan_queue_xmit+0xb3/0x190 [ipvlan]
[ 2203.655977] ipvlan_start_xmit+0x2e/0xb0 [ipvlan]
[ 2203.655984] xmit_one.constprop.0+0xe1/0x280
[ 2203.655992] dev_hard_start_xmit+0x62/0x100
[ 2203.656000] sch_direct_xmit+0x215/0x640
[ 2203.656028] __qdisc_run+0x153/0x1f0
[ 2203.656069] __dev_queue_xmit+0x77f/0x1030
[ 2203.656173] ip_finish_output2+0x59b/0xc20
[ 2203.656244] __ip_finish_output.part.0+0x318/0x3d0
[ 2203.656312] ip_finish_output+0x168/0x190
[ 2203.656320] ip_output+0x12d/0x220
[ 2203.656357] __ip_queue_xmit+0x392/0x880
[ 2203.656380] __tcp_transmit_skb+0x1088/0x11c0
[ 2203.656436] __tcp_retransmit_skb+0x475/0xa30
[ 2203.656505] tcp_retransmit_skb+0x2d/0x190
[ 2203.656512] tcp_retransmit_timer+0x3af/0x9a0
[ 2203.656519] tcp_write_timer_handler+0x3ba/0x510
[ 2203.656529] tcp_write_timer+0x55/0x180
[ 2203.656542] call_timer_fn+0x3f/0x1d0
[ 2203.656555] expire_timers+0x160/0x200
[ 2203.656562] run_timer_softirq+0x1f4/0x480
[ 2203.656606] __do_softirq+0xfd/0x402
[ 2203.656613] asm_call_irq_on_stack+0x12/0x20
[ 2203.656617] </IRQ>
[ 2203.656623] do_softirq_own_stack+0x37/0x50
[ 2203.656631] irq_exit_rcu+0x134/0x1a0
[ 2203.656639] sysvec_apic_timer_interrupt+0x36/0x80
[ 2203.656646] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 2203.656654] RIP: 0010:default_idle+0x13/0x20
[ 2203.656663] Code: 89 f0 5d 41 5c 41 5d 41 5e c3 cc cc cc cc cc cc cc
cc cc cc cc cc cc 0f 1f 44 00 00 0f 1f 44 00 00 0f 00 2d 9f 32 57 00 fb
f4 <c3> cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 54 be 08
[ 2203.656668] RSP: 0018:ffff88810036fe78 EFLAGS: 00000256
[ 2203.656676] RAX: ffffffffaf2a87f0 RBX: ffff888100360000 RCX:
ffffffffaf290191
[ 2203.656681] RDX: 0000000000098b5e RSI: 0000000000000004 RDI:
ffff88811a3c4f60
[ 2203.656686] RBP: 0000000000000000 R08: 0000000000000001 R09:
ffff88811a3c4f63
[ 2203.656690] R10: ffffed10234789ec R11: 0000000000000001 R12:
0000000000000003
[ 2203.656695] R13: ffff888100360000 R14: 0000000000000000 R15:
0000000000000000
[ 2203.656729] default_idle_call+0x5a/0x150
[ 2203.656735] cpuidle_idle_call+0x1c6/0x220
[ 2203.656780] do_idle+0xab/0x100
[ 2203.656786] cpu_startup_entry+0x19/0x20
[ 2203.656793] secondary_startup_64_no_verify+0xc2/0xcb
[ 2203.657409] The buggy address belongs to the page:
[ 2203.658648] page:0000000027a9842f refcount:1 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0x11a388
[ 2203.658665] flags:
0x17ffffc0001000(reserved|node=0|zone=2|lastcpupid=0x1fffff)
[ 2203.658675] raw: 0017ffffc0001000 ffffea000468e208 ffffea000468e208
0000000000000000
[ 2203.658682] raw: 0000000000000000 0000000000000000 00000001ffffffff
0000000000000000
[ 2203.658686] page dumped because: kasan: bad access detected
To reproduce(ipvlan with IPVLAN_MODE_L3):
Env setting:
=======================================================
modprobe ipvlan ipvlan_default_mode=1
sysctl net.ipv4.conf.eth0.forwarding=1
iptables -t nat -A POSTROUTING -s 20.0.0.0/255.255.255.0 -o eth0 -j
MASQUERADE
ip link add gw link eth0 type ipvlan
ip -4 addr add 20.0.0.254/24 dev gw
ip netns add net1
ip link add ipv1 link eth0 type ipvlan
ip link set ipv1 netns net1
ip netns exec net1 ip link set ipv1 up
ip netns exec net1 ip -4 addr add 20.0.0.4/24 dev ipv1
ip netns exec net1 route add default gw 20.0.0.254
ip netns exec net1 tc qdisc add dev ipv1 root netem loss 10%
ifconfig gw up
iptables -t filter -A OUTPUT -p tcp --dport 8888 -j REJECT --reject-with
icmp-port-unreachable
=======================================================
And then excute the shell(curl any address of eth0 can reach):
for((i=1;i<=100000;i++))
do
ip netns exec net1 curl x.x.x.x:8888
done
=======================================================
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: "t.feng" <fengtao40@huawei.com>
Suggested-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.
Fixes: 5e8c5adf95f8 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before blamed commit, pskb_may_pull() was used instead
of skb_header_pointer() in __vlan_get_protocol() and friends.
Few callers depended on skb->head being populated with MAC header,
syzbot caught one of them (skb_mac_gso_segment())
Add vlan_get_protocol_and_depth() to make the intent clearer
and use it where sensible.
This is a more generic fix than commit e9d3f80935b6
("net/af_packet: make sure to pull mac header") which was
dealing with a similar issue.
kernel BUG at include/linux/skbuff.h:2655 !
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 1441 Comm: syz-executor199 Not tainted 6.1.24-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
RIP: 0010:__skb_pull include/linux/skbuff.h:2655 [inline]
RIP: 0010:skb_mac_gso_segment+0x68f/0x6a0 net/core/gro.c:136
Code: fd 48 8b 5c 24 10 44 89 6b 70 48 c7 c7 c0 ae 0d 86 44 89 e6 e8 a1 91 d0 00 48 c7 c7 00 af 0d 86 48 89 de 31 d2 e8 d1 4a e9 ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
RSP: 0018:ffffc90001bd7520 EFLAGS: 00010286
RAX: ffffffff8469736a RBX: ffff88810f31dac0 RCX: ffff888115a18b00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffc90001bd75e8 R08: ffffffff84697183 R09: fffff5200037adf9
R10: 0000000000000000 R11: dffffc0000000001 R12: 0000000000000012
R13: 000000000000fee5 R14: 0000000000005865 R15: 000000000000fed7
FS: 000055555633f300(0000) GS:ffff8881f6a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 0000000116fea000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
[<ffffffff847018dd>] __skb_gso_segment+0x32d/0x4c0 net/core/dev.c:3419
[<ffffffff8470398a>] skb_gso_segment include/linux/netdevice.h:4819 [inline]
[<ffffffff8470398a>] validate_xmit_skb+0x3aa/0xee0 net/core/dev.c:3725
[<ffffffff84707042>] __dev_queue_xmit+0x1332/0x3300 net/core/dev.c:4313
[<ffffffff851a9ec7>] dev_queue_xmit+0x17/0x20 include/linux/netdevice.h:3029
[<ffffffff851b4a82>] packet_snd net/packet/af_packet.c:3111 [inline]
[<ffffffff851b4a82>] packet_sendmsg+0x49d2/0x6470 net/packet/af_packet.c:3142
[<ffffffff84669a12>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff84669a12>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff84669a12>] __sys_sendto+0x472/0x5f0 net/socket.c:2139
[<ffffffff84669c75>] __do_sys_sendto net/socket.c:2151 [inline]
[<ffffffff84669c75>] __se_sys_sendto net/socket.c:2147 [inline]
[<ffffffff84669c75>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147
[<ffffffff8551d40f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff8551d40f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80
[<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 469aceddfa3e ("vlan: consolidate VLAN parsing code and limit max parsing depth")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In synopsys_xpcs_compat[], the DW_XPCS_2500BASEX entry was setting
the number of interfaces using the xpcs_2500basex_features array
rather than xpcs_2500basex_interfaces. This causes us to overflow
the array of interfaces. Fix this.
Fixes: f27abde3042a ("net: pcs: add 2500BASEX support for Intel mGbE controller")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3ce9
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.
ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000
To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.
Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3ce9 ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for NULL pointer to avoid kernel crashing in case of missing WO
firmware in case only a single WEDv2 device has been initialized, e.g. on
MT7981 which can connect just one wireless frontend.
Fixes: 86ce0d09e424 ("net: ethernet: mtk_eth_soc: use WO firmware for MT7981")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver works in the "legacy" addressing mode, we need to write
to the expansion register (0x17) with bits 11:8 set to 0xf to properly
select the expansion register passed as argument.
Fixes: f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230508231749.1681169-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Initialize MAC_ONEUS_TIC_COUNTER register with correct value derived
from CSR clock, otherwise EEE is unstable on at least NXP i.MX8M Plus
and Micrel KSZ9131RNX PHY, to the point where not even ARP request can
be sent out.
i.MX 8M Plus Applications Processor Reference Manual, Rev. 1, 06/2021
11.7.6.1.34 One-microsecond Reference Timer (MAC_ONEUS_TIC_COUNTER)
defines this register as:
"
This register controls the generation of the Reference time (1 microsecond
tic) for all the LPI timers. This timer has to be programmed by the software
initially.
...
The application must program this counter so that the number of clock cycles
of CSR clock is 1us. (Subtract 1 from the value before programming).
For example if the CSR clock is 100MHz then this field needs to be programmed
to value 100 - 1 = 99 (which is 0x63).
This is required to generate the 1US events that are used to update some of
the EEE related counters.
"
The reset value is 0x63 on i.MX8M Plus, which means expected CSR clock are
100 MHz. However, the i.MX8M Plus "enet_qos_root_clk" are 266 MHz instead,
which means the LPI timers reach their count much sooner on this platform.
This is visible using a scope by monitoring e.g. exit from LPI mode on TX_CTL
line from MAC to PHY. This should take 30us per STMMAC_DEFAULT_TWT_LS setting,
during which the TX_CTL line transitions from tristate to low, and 30 us later
from low to high. On i.MX8M Plus, this transition takes 11 us, which matches
the 30us * 100/266 formula for misconfigured MAC_ONEUS_TIC_COUNTER register.
Configure MAC_ONEUS_TIC_COUNTER based on CSR clock, so that the LPI timers
have correct 1us reference. This then fixes EEE on i.MX8M Plus with Micrel
KSZ9131RNX PHY.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Harald Seiler <hws@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Verdin iMX8MP
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20230506235845.246105-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate
ESDHC_FLAG_HS400* only on 8bit bus"), the property "no-mmc-hs400"
from device tree file do not work any more.
This patch reorder the code, which can avoid the warning message
"drop HS400 support since no 8-bit bus" and also make the property
"no-mmc-hs400" from dts file works.
Fixes: 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230504112222.3599602-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This commit adds memory barrier for the 'vq' update in function
mlxbf_tmfifo_virtio_find_vqs() to avoid potential race due to
out-of-order memory write. It also adds barrier for the 'is_ready'
flag to make sure the initializations are visible before this flag
is checked.
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/b98c0ab61d644ba38fa9b3fd1607b138b0dd820b.1682518748.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
If devm_reset_control_get_optional_exclusive() fails, some resources still
need to be released. So branch to the error handling path instead of
returning directly.
Fixes: aad53d4ee756 ("mmc: sdhci-cadence: Support mmc hardware reset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Brad Larson <blarson@amd.com>
Link: https://lore.kernel.org/r/f61599a9ef23767c2d66e5af9c975f05ef1cec6b.1682430069.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 614f0388f580 ("mmc: block: move single ioctl() commands to block requests")
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add touchscreen info for the Dexp Ursus KX210i
Signed-off-by: Andrey Avdeev <jamesstoun@gmail.com>
Link: https://lore.kernel.org/r/ZE4gRgzRQCjXFYD0@avdeevavpc
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Juno Tablet
The Juno Computers Juno Tablet has an upside-down mounted Goodix
touchscreen. Add a quirk to invert both axis to correct for this.
Link: https://junocomputers.com/us/product/juno-tablet/
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230505210323.43177-1-hdegoede@redhat.com
|
|
There has been a lot of confusion around which platform profiles are
supported on various platforms and it would be useful to have a debug
method to be able to override the profile mode that is selected.
I don't expect this to be used in anything other than debugging in
conjunction with Lenovo engineers - but it does give a way to get a
system working whilst we wait for either FW fixes, or a driver fix
to land upstream, if something is wonky in the mode detection logic
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230505132523.214338-2-mpearson-lenovo@squebb.ca
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
I had incorrectly thought that PSC profiles were not usable on Intel
platforms so had blocked them in the driver initialistion. This broke
platform profiles on the T490.
After discussion with the FW team PSC does work on Intel platforms and
should be allowed.
Note - it's possible this may impact other platforms where it is advertised
but special driver support that only Windows has is needed. But if it does
then they will need fixing via quirks. Please report any issues to me so I
can get them addressed - but I haven't found any problems in testing...yet
Fixes: bce6243f767f ("platform/x86: thinkpad_acpi: do not use PSC mode on Intel platforms")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2177962
Cc: stable@vger.kernel.org
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230505132523.214338-1-mpearson-lenovo@squebb.ca
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fixes micmute key of HP Envy X360 ey0xxx.
Signed-off-by: Fae <faenkhauser@gmail.com>
Link: https://lore.kernel.org/r/20230425063644.11828-1-faenkhauser@gmail.com
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Currently when the uncore_write() returns error, it is silently
ignored. Return error to user space when uncore_write() fails.
Fixes: 49a474c7ba51 ("platform/x86: Add support for Uncore frequency control")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230418153230.679094-1-srinivas.pandruvada@linux.intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
After commit 27a2195efa8d26447c ("power: supply: core: auto-exposure
of simple-battery data") we call power_supply_get_battery_info() in
__power_supply_register(), but it causes test_battery crash with NULL
pointer:
[ 7.524846] __power_supply_register: Expected proper parent device for 'test_battery'
[ 7.524856] CPU 3 Unable to handle kernel paging request at virtual address 0000000000000278, era == 9000000002fb279c, ra == 9000000003173434
[ 7.524862] Oops[#1]:
[ 7.524866] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 6.3.0+ #524
[ 7.524870] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022
[ 7.524872] pc 9000000002fb279c ra 9000000003173434 tp 90000001001f0000 sp 90000001001f3c00
[ 7.524875] a0 0000000000000000 a1 0000000000000000 a2 0000000000000000 a3 9000000004553e13
[ 7.524878] a4 9000000004553e16 a5 ffffffffffffffff a6 9000000003fd0948 a7 0000000000000030
[ 7.524881] t0 9000000003173434 t1 90000000035e2c00 t2 0000000000000001 t3 00000000fffff2b0
[ 7.524883] t4 0000000000000007 t5 fffffffffffffffe t6 0000000000000000 t7 0000000000000010
[ 7.524886] t8 00000000000000b4 u0 00000001c0840c76 s9 0000000000000000 s0 0000000000000000
[ 7.524889] s1 900000000370c458 s2 0000000000000001 s3 9000000101f81000 s4 9000000101f81038
[ 7.524891] s5 9000000101f813a0 s6 900000000370c398 s7 9000000003eebd18 s8 90000000037c0070
[ 7.524894] ra: 9000000003173434 power_supply_get_battery_info+0xe4/0x710
[ 7.591224] ERA: 9000000002fb279c __dev_fwnode+0x8/0x20
[ 7.853583] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 7.859740] PRMD: 00000004 (PPLV0 +PIE -PWE)
[ 7.864073] EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[ 7.868839] ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
[ 7.873430] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 7.878884] BADV: 0000000000000278
[ 7.882346] PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
[ 7.888056] Modules linked in:
[ 7.891088] Process swapper/0 (pid: 1, threadinfo=0000000091357ee8, task=00000000313d98cb)
[ 7.899307] Stack : 00000000000000b4 900000000279aca8 0000000000000001 0000000000000000
[ 7.907274] 0000000000000049 0000000000000408 9000000100008c00 90000000035b6370
[ 7.915238] 900000000b801080 90000000029a440c 9000000003eb4680 9000000003eb4680
[ 7.923202] 9000000101f81038 900000000357cdcc 0000000000000001 900000000370c458
[ 7.931166] 9000000101f81000 90000000037c0070 9000000003eebd18 900000000370c398
[ 7.939131] 90000000045f4530 9000000101f81038 0000000000000000 0000000000000001
[ 7.947095] 900000000370c458 9000000101f81000 0000000000000000 9000000003173e64
[ 7.955059] 0000000000000026 9000000003de3880 9000000100562040 900000000357e07c
[ 7.963023] 000000000000026f 0000000000000001 90000001001f3d68 fffffffffffffff5
[ 7.970987] 90000000036d2ca8 90000000027429d8 90000000037c0030 0000000000000001
[ 7.978951] ...
[ 7.981379] Call Trace:
[ 7.981382] [<9000000002fb279c>] __dev_fwnode+0x8/0x20
[ 7.988916] [<9000000003173434>] power_supply_get_battery_info+0xe4/0x710
[ 7.995666] [<9000000003173e64>] __power_supply_register+0x404/0x580
[ 8.001984] [<900000000379d368>] test_power_init+0x6c/0x124
[ 8.007527] [<90000000026e08f8>] do_one_initcall+0x58/0x1ec
[ 8.013066] [<9000000003761614>] kernel_init_freeable+0x290/0x310
[ 8.019127] [<90000000035b40e8>] kernel_init+0x24/0x11c
[ 8.024324] [<90000000026e2048>] ret_from_kernel_thread+0xc/0xa4
[ 8.030295]
[ 8.031769] Code: 4c000020 0015002c 03400000 <28c9e08c> 40000d80 02c06184 4c000020 28ca0084 4c000020
Root cause: psy->dev.parent is NULL in power_supply_get_battery_info(),
so change the else branch to be 'else if (psy->dev.parent)' and return
-ENOENT if psy->dev.parent is NULL.
Fixes: 27a2195efa8d26447c ("power: supply: core: auto-exposure of simple-battery data")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be
cleared by writing to Interrupt Mask Clear (IMR) and interrupt
status should be cleared properly at shutdown/init.
This fixes an error where interrupts are left enabled during resume
from hibernation with `CONFIG_USB4=y`.
Fixes: 468c49f44759 ("thunderbolt: Disable interrupt auto clear for rings")
Cc: stable@vger.kernel.org # v6.3
Reported-by: Takashi Iwai <tiwai@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.
While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.
So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.
Fixes: cc2195fe536c ("firmware: arm_ffa: Add support for MEM_* interfaces")
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488b9 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Commit bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
adds support to discovery the UUIDs of the partitions or just fetch the
partition count using the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag.
However the commit doesn't handle the fact that the older version doesn't
understand the flag and must be MBZ which results in firmware returning
invalid parameter error. That results in the failure of the driver probe
which is in correct.
Limit the usage of the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag for the
versions above v1.0(i.e v1.1 and onwards) which fixes the issue.
Fixes: bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-2-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Currently ffa_drv->remove() is called unconditionally from
ffa_device_remove(). Since the driver registration doesn't check for it
and allows it to be registered without .remove callback, we need to check
for the presence of it before executing it from ffa_device_remove() to
above a NULL pointer dereference like the one below:
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
| Mem abort info:
| ESR = 0x0000000086000004
| EC = 0x21: IABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| FSC = 0x04: level 0 translation fault
| user pgtable: 4k pages, 48-bit VAs, pgdp=0000000881cc8000
| [0000000000000000] pgd=0000000000000000, p4d=0000000000000000
| Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP
| CPU: 3 PID: 130 Comm: rmmod Not tainted 6.3.0-rc7 #6
| Hardware name: FVP Base RevC (DT)
| pstate: 63402809 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=-c)
| pc : 0x0
| lr : ffa_device_remove+0x20/0x2c
| Call trace:
| 0x0
| device_release_driver_internal+0x16c/0x260
| driver_detach+0x90/0xd0
| bus_remove_driver+0xdc/0x11c
| driver_unregister+0x30/0x54
| ffa_driver_unregister+0x14/0x20
| cleanup_module+0x18/0xeec
| __arm64_sys_delete_module+0x234/0x378
| invoke_syscall+0x40/0x108
| el0_svc_common+0xb4/0xf0
| do_el0_svc+0x30/0xa4
| el0_svc+0x2c/0x7c
| el0t_64_sync_handler+0x84/0xf0
| el0t_64_sync+0x190/0x194
Fixes: 244f5d597e1e ("firmware: arm_ffa: Add missing remove callback to ffa_bus_type")
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-1-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
scmi_xfer_raw_worker_init() is specifying a flag, WQ_SYSFS, as @max_active.
Fix it by or'ing WQ_SYSFS into @flags so that it actually enables sysfs
interface and using 0 for @max_active for the default setting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 3c3d818a9317 ("firmware: arm_scmi: Add core raw transmission support")
Link: https://lore.kernel.org/r/ZEGTnajiQm7mkkZS@slm.duckdns.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The #if check is wrong, leading to a build failure:
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c: In function 'mxc_isi_channel_set_inbuf':
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:33:5: error: "CONFIG_ARCH_DMA_ADDR_T_64BIT" is not defined, evaluates to 0 [-Werror=undef]
33 | #if CONFIG_ARCH_DMA_ADDR_T_64BIT
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
This could just be an #ifdef, but it seems nicer to just remove the
check entirely. Apparently the only reason for the #ifdef is to avoid
another warning:
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:55:24: error: right shift count >= width of type [-Werror=shift-count-overflow]
But this is best avoided by using the lower_32_bits()/upper_32_bits()
helpers.
Fixes: cf21f328fcaf ("media: nxp: Add i.MX8 ISI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This id was removed in commit b47018a778c1 ("platform/x86: intel_scu_ipc:
Remove Lincroft support"), saying it is only used on Moorestown,
but apparently the same id is also used on Medfield.
Tested on the Medfield based Motorola RAZR i smartphone.
Signed-off-by: Julian Winkler <julian.winkler1@web.de>
Link: https://lore.kernel.org/r/20230416154932.6579-1-julian.winkler1@web.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
I gave up using MIPS OCTEON hardware after the drivers were deleted from
staging in 2019. Afterwards, the driver seems to be added back but the TODO
contact name was not updated accordingly. Delete my name, as I still get
mails from people asking help with the driver and their systems.
Fixes: 422d97b8b05e ("Revert "staging: octeon: delete driver"")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230427211606.GD881984@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
current or voltage
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094dbb ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
stabilize
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sign changes
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27xxx_battery_current_and_status()
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d07929 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Even when urgent BKOPS fails, the consumer will get stuck in runtime
suspend status. Like commit 1a5665fc8d7a ("scsi: ufs: core: WLUN suspend
SSU/enter hibern8 fail recovery"), trigger the error handler and return
-EBUSY to break the suspend.
Fixes: b294ff3e3449 ("scsi: ufs: core: Enable power management for wlun")
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Link: https://lore.kernel.org/r/20230425031721epcms2p5d4de65616478c967d466626e20c42a3a@epcms2p5
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When CONFIG_OF is disabled, the 'data' variable is not used at all
because of_match_node() turns into a dummy macro:
drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.c: In function 'mdp_comp_sub_create':
drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.c:1038:36: error: unused variable 'data' [-Werror=unused-variable]
1038 | const struct mtk_mdp_driver_data *data = mdp->mdp_data;
| ^~~~
Remove the variable again by moving the pointer dereference into the
of_match_node call.
Fixes: b385b991ef2f ("media: platform: mtk-mdp3: chip config split about subcomponents")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
gcc warns about some functions being unused when CONFIG_PM_SLEEP
is disabled:
drivers/media/platform/nxp/imx8-isi/imx8-isi-core.c:328:12: error: 'mxc_isi_pm_resume' defined but not used [-Werror=unused-function]
328 | static int mxc_isi_pm_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~
drivers/media/platform/nxp/imx8-isi/imx8-isi-core.c:314:12: error: 'mxc_isi_pm_suspend' defined but not used [-Werror=unused-function]
314 | static int mxc_isi_pm_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~
Use the modern SYSTEM_SLEEP_PM_OPS()/RUNTIME_PM_OPS() helpers in place
of the old SET_SYSTEM_SLEEP_PM_OPS()/SET_RUNTIME_PM_OPS() ones.
By convention, use pm_ptr() to guard the reference to the operations.
This makes no difference as long as the driver requires CONFIG_PM,
but is what users of SET_RUNTIME_PM_OPS() are supposed to do.
Fixes: cf21f328fcaf ("media: nxp: Add i.MX8 ISI driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
When doing format validation for NV12 the width and height should be
aligned to 32 pixels.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The VIN modules on Gen3 can not scale NV12, fail format validation if
the user tries. Currently no frames are produced if this is attempted.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Enable k10temp on this system.
[ bp: Massage. ]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230427053338.16653-3-mario.limonciello@amd.com
|
