| Age | Commit message (Collapse) | Author |
|---|
|
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com
|
|
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com
|
|
DMC version 1.06 has a known bug, where the firmware polls forever for a
port PLL to lock, if the PLL was disabled when entering DC5, which locks
up the machine. Version 1.07 fixes this, so make that the minimum
required version on BXT.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-2-git-send-email-imre.deak@intel.com
|
|
pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices
ranging from 1 to MAX. This leads to a corner case where we try to request
the pin number = MAX and fails.
bit_pos value is being calculted using ffs. pin_num_from_lsb uses
bit_pos value. pins array is populated with:
pin + pin_num_from_lsb.
The above is 1 more than usual bit indices as bit_pos uses ffs to compute
first set bit. Hence the last of the pins array is populated with the MAX
value and not MAX - 1 which causes error when we call pin_request.
mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1))
Consequently val_pos and submask are correct.
Hence use __ffs which gives (ffs(x) - 1) as the first bit set.
fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The debounce time unit for gpio_chip.set_debounce is us but
mtk_gpio_set_debounce regard it as ms.
Fix this by correct debounce time array dbnc_arr so it can find correct
debounce setting. Debounce time for first debounce setting is 500us,
correct this as well.
While I'm at it, also change the debounce time array name to
"debounce_time" for readability.
Cc: stable@vger.kernel.org
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the legacy drm_send_vblank_event() with the new helper function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460656118-16766-4-git-send-email-gustavo@padovan.org
|
|
HP ProBook 440 G3 laptop needs a non-standard mapping (x_inverted_usd).
Signed-off-by: Martin Vajnar <martin.vajnar@gmail.com>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a binutils fix, an lguest fix, an mcelog fix and a missing
documentation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Avoid using object after free in genpool
lguest, x86/entry/32: Fix handling of guest syscalls using interrupt gates
x86/build: Build compressed x86 kernels as PIE
x86/mm/pkeys: Add missing Documentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- fix a 4.6-rc1 bio-based DM 'struct dm_target_io' leak in an error
path
- stable@ fix for DM cache metadata's READ_LOCK macros that were
incorrectly returning error if the block manager was in read-only
mode; also cleanup multi-statement macros to use do {} while(0)
* tag 'dm-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache metadata: fix READ_LOCK macros and cleanup WRITE_LOCK macros
dm: fix dm_target_io leak if clone_bio() returns an error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"A single one-line fix to turn the regmap cache from an RB-tree to a
flat cache to avoid lockdep and abort issues"
* tag 'pwm/for-4.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: fsl-ftm: Use flat regmap cache
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox fixes from Jussi Brar:
"Misc fixes:
mailbox-test driver:
- prevent memory leak and another cosmetic change
mailbox:
- change the returned error code
Xgene driver:
- return -ENOMEM instead of PTR_ERR for failed devm_kzalloc"
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Stop using ENOSYS for anything other than unimplemented syscalls
mailbox: mailbox-test: Prevent memory leak
mailbox: mailbox-test: Use more consistent format for calling copy_from_user()
mailbox: xgene-slimpro: Fix wrong test for devm_kzalloc
|
|
Only core revisions older than 4 use BGMAC_CMDCFG_SR_REV0. This mainly
fixes support for BCM4708A0KF SoCs with Ethernet core rev 5 (it means
only some devices as most of BCM4708A0KF-s got core rev 4).
This was tested for regressions on BCM47094 which doesn't seem to care
which bit gets used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes an NFS regression caused by the skcipher/hash conversion in
sunrpc. It also fixes a build problem in certain configurations with
bcm63xx"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm63xx - fix device tree compilation
sunrpc: Fix skcipher/shash conversion
|
|
We now have a positive report of another Huawei device needing
this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form
factor modem with no obvious relationship to the E3372 (12d1:157d)
we already have a quirk entry for. This is reason enough to
believe the quirk might be necessary for any number of current
and future Huawei devices.
Applying the quirk to all Huawei devices, since it is crucial
to any device affected by the firmware bug, while the impact
on non-affected devices is negligible.
The quirk can if necessary be disabled per-device by writing
N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- fix boot error reverting commit cc8ed76938b5
("soc: mediatek: SCPSYS: Fix double enabling of regulators")
* tag 'v4.6-soc-fixes' of https://github.com/mbgg/linux-mediatek:
Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"
|
|
The READ_LOCK macro was incorrectly returning -EINVAL if
dm_bm_is_read_only() was true -- it will always be true once the cache
metadata transitions to read-only by dm_cache_metadata_set_read_only().
Wrap READ_LOCK and WRITE_LOCK multi-statement macros in do {} while(0).
Also, all accesses of the 'cmd' argument passed to these related macros
are now encapsulated in parenthesis.
A follow-up patch can be developed to eliminate the use of macros in
favor of pure C code. Avoiding that now given that this needs to apply
to stable@.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: d14fcf3dd79 ("dm cache: make sure every metadata function checks fail_io")
Cc: stable@vger.kernel.org
|
|
This fixes Ethernet on D-Link DIR-885L with BCM47094 SoC. Felix reported
similar fix was needed for his BCM4709 device (Buffalo WXR-1900DHP?).
I tested this for regressions on BCM4706, BCM4708A0 and BCM47081A0.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multiple users have reported device initialization failure due the driver
not receiving legacy PCI interrupts. This is not unique to any particular
controller, but has been observed on multiple platforms.
There have been no issues reported or observed when with message signaled
interrupts, so this patch attempts to use MSI-x during initialization,
falling back to MSI. If that fails, legacy would become the default.
The setup_io_queues error handling had to change as a result: the admin
queue's msix_entry used to be initialized to the legacy IRQ. The case
where nr_io_queues is 0 would fail request_irq when setting up the admin
queue's interrupt since re-enabling MSI-x fails with 0 vectors, leaving
the admin queue's msix_entry invalid. Instead, return success immediately.
Reported-by: Tim Muhlemmer <muhlemmer@gmail.com>
Reported-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The PCI config access checked the file capabilities correctly, but used
the itnernal security capability check rather than the helper function
that is actually meant for that.
The security_capable() has unusual return values and is not meant to be
used elsewhere (the only other use is in the capability checking
functions that we actually intend people to use, and this odd PCI usage
really stood out when looking around the capability code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If you make it here other than through err_destroy_encoder, vc4->hdmi
is still NULL.
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The DPI interface involves taking a ton of our GPIOs to be used as
outputs, and routing display signals over them in parallel.
v2: Use display_info.bus_formats[] to replace our custom DT
properties.
v3: Rebase on V3D documentation changes.
v4: Fix rebase detritus from V3D documentation changes.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
|
|
If this function fails the callers expect that *private_conf is set to
an ERR_PTR() but that isn't true for the first error path where we can't
allocate "conf". It leads to some uninitialized variable bugs.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Use flat regmap cache to avoid lockdep warning at probe:
[ 0.697285] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
[ 0.697449] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first writes.
However, allocations in an atomic context (e.g. when a spinlock is held)
are not allowed. The function regmap_write calls map->lock, which
acquires a spinlock in the fast_io case. Since the pwm-fsl-ftm driver
uses MMIO, the regmap bus of type regmap_mmio is being used which has
fast_io set to true.
The MMIO space of the pwm-fsl-ftm driver is reasonable condense, hence
using the much faster flat regmap cache is anyway the better choice.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Regmap functionality has been integrated into pinctrl-imx.c with commit
8626ada8 which might trigger build failures when regmap is not selected
otherwise. Hence, make Kconfig aware about this new dependency.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
HSW still has the wake FIFO, so let's check it.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Fixes: 05a2fb157e44 ("drm/i915: Consolidate forcewake code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460633942-24013-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
As we did on VLV, split the gt irq handling to ack and handler phases on
CHV. Leave the BDW+ codepath mostly intact for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
It looks silly to pass both dev and dev_priv to the snb/ilk gt irq
handlers. Just pass dev_priv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
No need to actually handle the GT/PM interrupt while we have interrupt
sources disabled. Move the actual processing to happen after we've
restored VLV_IER and master interrupt enable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Minimize the amount of stuff we do with interrupt sources disabled by
splitting the PIPESTAT irq handling into ack+handler phases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Split the VLV/CHV hoplug irq handling to ack and handler phases. This
way we can move the actual irq handling outside the section where
we have disabled the interrupt sources.
For now, we leave things as is for pre-VLV GMCH platforms, but
eventually they could get the same treatment.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Now that we've dealt with the races in clearing IIR bits via VLV_IER
and the master interrupt enable, we can go ahead aliminate the loop
from the VLV interrupt handler.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
On VLV/CHV the master interrupt enable bit only affects GT/PM
interrupts. Display interrupts are not affected by the master
irq control.
Also it seems that the CPU interrupt will only be generated when
the combined result of all GT/PM/display interrupts has a 0->1
edge. We already use the master interrupt enable bit to make sure
GT/PM interrupt can generate such an edge if we don't end up clearing
all IIR bits. We must do the same for display interrupts, and for
that we can simply clear out VLV_IER, and restore after we've acked
all the interrupts we are about to process.
So with both master interrupt enable and VLV_IER cleared out, we will
guarantee that there will be a 0->1 edge if any IIR bits are still set
at the end, and thus another CPU interrupt will be generated.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 579de73b048a ("drm/i915: Exit cherryview_irq_handler() after one pass")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Like on CHV, let's clear out the master irq enable bit when we ack
GT/PM interrupts. This will allow GT/PM interrupts to re-raise the
CPU interrupt if we fail to clear all the bits from the IIR(s).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
On VLV/CHV VLV_IIR is not double double buffered, and it doesn't detect
edges from PIPESTAT & co. like it does on gen4. Instead it just
directly latches the level from PIPESTAT & co. That means we must clear
VLV_IIR after PIPESTAT & co. or else we'll get a spurious bit in VLV_IIR
every single time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We're lacking VLV_MASTER_IER setup from valleyview_irq_preinstall(), so
add it there. Also cargo cult in some POSTING_READ()s to match the other
platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Use GEN8_MASTER_IRQ_CONTROL instead of DE_MASTER_IRQ_CONTROL or
MASTER_INTERRUPT_ENABLE with the GEN8_MASTER_IRQ register. They're
all bit 31 so there's no actual bug here, but let's be consistent
which name we use for the bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460571598-24452-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000
While at it, move the assignments out of the if().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Allow for the MOCS to be programmed for all engines.
Currently we program the MOCS when the first render batch
goes through. This works on most platforms but fails on
platforms that do not run a render batch early,
i.e. headless servers. The patch now programs all initialised engines
on init and the RCS is programmed again within the initial batch. This
is done for predictable consistency with regards to the hardware
context.
Hardware context loading sets the values of the MOCS for RCS
and L3CC. Programming them from within the batch makes sure that
the render context is valid, no matter what the previous state of
the saved-context was.
v2: posted correct version to the mailing list.
v3: moved programming to within engine->init_hw() (Chris Wilson)
v4: code formatting and white-space changes. (Chris Wilson)
Testcase: igt/gem_mocs_settings
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460556205-6644-1-git-send-email-chris@chris-wilson.co.uk
|
|
Conceptually, each request is a record of a hardware transaction - we
build up a list of pending commands and then either commit them to
hardware, or cancel them. However, whilst building up the list of
pending commands, we may modify state outside of the request and make
references to the pending request. If we do so and then cancel that
request, external objects then point to the deleted request leading to
both graphical and memory corruption.
The easiest example is to consider object/VMA tracking. When we mark an
object as active in a request, we store a pointer to this, the most
recent request, in the object. Then we want to free that object, we wait
for the most recent request to be idle before proceeding (otherwise the
hardware will write to pages now owned by the system, or we will attempt
to read from those pages before the hardware is finished writing). If
the request was cancelled instead, that wait completes immediately. As a
result, all requests must be committed and not cancelled if the external
state is unknown.
All that remains of i915_gem_request_cancel() users are just a couple of
extremely unlikely allocation failures, so remove the API entirely.
A consequence of committing all incomplete requests is that we generate
excess breadcrumbs and fill the ring much more often with dummy work. We
have completely undone the outstanding_last_seqno optimisation.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93907
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-16-git-send-email-chris@chris-wilson.co.uk
|
|
After mi_set_context() succeeds, we need to update the state of the
engine's last_context. This ensures that we hold a pin on the context
whilst the hardware may write to it. However, since we didn't complete
the post-switch setup of the context, we need to force the subsequent
use of the same context to complete the setup (which means updating
should_skip_switch()).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-15-git-send-email-chris@chris-wilson.co.uk
|
|
Having the !RCS legacy context switch threaded through the RCS switching
code makes it much harder to follow and understand. In the next patch, I
want to fix a bug handling the incomplete switch, this is made much
simpler if we segregate the two paths now.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-14-git-send-email-chris@chris-wilson.co.uk
|
|
As paranoia, we want to ensure that the CPU's PTEs have been revoked for
the object before we return from i915_gem_release_mmap(). This allows us
to rely on there being no outstanding memory accesses from userspace
and guarantees serialisation of the code against concurrent access just
by calling i915_gem_release_mmap().
v2: Reduce the mb() into a wmb() following the revoke.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-13-git-send-email-chris@chris-wilson.co.uk
|
|
For reasons unknown Sandybridge GT1 (at least) will eventually hang when
it encounters a ring wraparound at offset 0. The test case that
reproduces the bug reliably forces a large number of interrupted context
switches, thereby causing very frequent ring wraparounds, but there are
similar bug reports in the wild with the same symptoms, seqno writes
stop just before the wrap and the ringbuffer at address 0. It is also
timing crucial, but adding various delays hasn't helped pinpoint where
the window lies.
Whether the fault is restricted to the ringbuffer itself or the GTT
addressing is unclear, but moving the ringbuffer fixes all the hangs I
have been able to reproduce.
References: (e.g.) https://bugs.freedesktop.org/show_bug.cgi?id=93262
Testcase: igt/gem_exec_whisper/render-contexts-interruptible #snb-gt1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-12-git-send-email-chris@chris-wilson.co.uk
|
|
Two concurrent writes into the same register cacheline has the chance of
killing the machine on Ivybridge and other gen7. This includes LRI
emitted from the command parser. The MI_SET_CONTEXT itself serves as
serialising barrier and prevents the pair of register writes in the first
packet from triggering the fault. However, if a second switch-context
immediately occurs then we may have two adjacent blocks of LRI to the
same registers which may then trigger the hang. To counteract this we
need to insert a delay after the second register write using SRM.
This is easiest to reproduce with something like
igt/gem_ctx_switch/interruptible that triggers back-to-back context
switches (with no operations in between them in the command stream,
which requires the execbuf operation to be interrupted after the
MI_SET_CONTEXT) but can be observed sporadically elsewhere when running
interruptible igt. No reports from the wild though, so it must be of low
enough frequency that no one has correlated the random machine freezes
with i915.ko
The issue was introduced with
commit 2c550183476dfa25641309ae9a28d30feed14379 [v3.19]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Dec 16 10:02:27 2014 +0000
drm/i915: Disable PSMI sleep messages on all rings around context switches
Testcase: igt/gem_ctx_switch/render-interruptible #ivb
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-11-git-send-email-chris@chris-wilson.co.uk
|
|
If we do not have lowlevel support for reseting the GPU, or if the user
has explicitly disabled reseting the device, the failure is expected.
Since it is an expected failure, we should be using a lower priority
message than *ERROR*, perhaps NOTICE. In the absence of DRM_NOTICE, just
emit the expected failure as a DEBUG message.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-10-git-send-email-chris@chris-wilson.co.uk
|
|
Reporting -EIO from i915_wait_request() has proven very troublematic
over the years, with numerous hard-to-reproduce bugs cropping up in the
corner case of where a reset occurs and the code wasn't expecting such
an error.
If the we reset the GPU or have detected a hang and wish to reset the
GPU, the request is forcibly complete and the wait broken. Currently, we
report either -EAGAIN or -EIO in order for the caller to retreat and
restart the wait (if appropriate) after dropping and then reacquiring
the struct_mutex (essential to allow the GPU reset to proceed). However,
if we take the view that the request is complete (no further work will
be done on it by the GPU because it is dead and soon to be reset), then
we can proceed with the task at hand and then drop the struct_mutex
allowing the reset to occur. This transfers the burden of checking
whether it is safe to proceed to the caller, which in all but one
instance it is safe - completely eliminating the source of all spurious
-EIO.
Of note, we only have two API entry points where we expect that
userspace can observe an EIO. First is when submitting an execbuf, if
the GPU is terminally wedged, then the operation cannot succeed and an
-EIO is reported. Secondly, existing userspace uses the throttle ioctl
to detect an already wedged GPU before starting using HW acceleration
(or to confirm that the GPU is wedged after an error condition). So if
the GPU is wedged when the user calls throttle, also report -EIO.
v2: Split more carefully the change to i915_wait_request() and assorted
ABI from the reset handling.
v3: Add a couple of WARN_ON(EIO) to the interruptible modesetting code
so that we don't start to leak EIO there in future (and break our hang
resistant modesetting).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-9-git-send-email-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-1-git-send-email-chris@chris-wilson.co.uk
|
|
Now that the reset_counter is stored on the request, we can rearrange
the code to handle reading the counter versus waiting during the atomic
modesetting for readibility (by deleting the hairiest of codes).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-8-git-send-email-chris@chris-wilson.co.uk
|
|
As the request is only valid during the same global reset epoch, we can
record the current reset_counter when constructing the request and reuse
it when waiting upon that request in future. This removes a very hairy
atomic check serialised by the struct_mutex at the time of waiting and
allows us to transfer those waits to a central dispatcher for all
waiters and all requests.
PS: With per-engine resets, we obviously cannot assume a global reset
epoch for the requests - a per-engine epoch makes the most sense. The
challenge then is how to handle checking in the waiter for when to break
the wait, as the fine-grained reset may also want to requeue the
request (i.e. the assumption that just because the epoch changes the
request is completed may be broken - or we just avoid breaking that
assumption with the fine-grained resets).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-7-git-send-email-chris@chris-wilson.co.uk
|
|
In the reset_counter, we use two bits to track a GPU hang and reset. The
low bit is a "reset-in-progress" flag that we set to signal when we need
to break waiters in order for the recovery task to grab the mutex. As
soon as the recovery task has the mutex, we can clear that flag (which
we do by incrementing the reset_counter thereby incrementing the gobal
reset epoch). By clearing that flag when the recovery task holds the
struct_mutex, we can forgo a second flag that simply tells GEM to ignore
the "reset-in-progress" flag.
The second flag we store in the reset_counter is whether the
reset failed and we consider the GPU terminally wedged. Whilst this flag
is set, all access to the GPU (at least through GEM rather than direct mmio
access) is verboten.
PS: Fun is in store, as in the future we want to move from a global
reset epoch to a per-engine reset engine with request recovery.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-6-git-send-email-chris@chris-wilson.co.uk
|
