| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-09-23
The first 2 patches are by Ziyang Xuan and optimize registration and
the sending in the CAN BCM protocol a bit.
The next 8 patches target the gs_usb driver. 7 are by me and first fix
the time hardware stamping support (added during this net-next cycle),
rename a variable, convert the usb_control_msg + manual
kmalloc()/kfree() to usb_control_msg_{send,rev}(), clean up the error
handling and add switchable termination support. The patch by Rhett
Aultman and Vasanth Sadhasivan convert the driver from
usb_alloc_coherent()/usb_free_coherent() to kmalloc()/URB_FREE_BUFFER.
The last patch is by Shang XiaoJing and removes an unneeded call to
dev_err() from the ctucanfd driver.
* tag 'linux-can-next-for-6.1-20220923' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ctucanfd: Remove redundant dev_err call
can: gs_usb: remove dma allocations
can: gs_usb: add switchable termination support
can: gs_usb: gs_make_candev(): clean up error handling
can: gs_usb: convert from usb_control_msg() to usb_control_msg_{send,recv}()
can: gs_usb: gs_cmd_reset(): rename variable holding struct gs_can pointer to dev
can: gs_usb: gs_can_open(): initialize time counter before starting device
can: gs_usb: add missing lock to protect struct timecounter::cycle_last
can: gs_usb: gs_usb_get_timestamp(): fix endpoint parameter for usb_control_msg_recv()
can: bcm: check the result of can_send() in bcm_can_tx()
can: bcm: registration process optimization in bcm_module_init()
====================
Link: https://lore.kernel.org/r/20220923120859.740577-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The datasheet [1] explicit describes it as requirement for a reset.
[1] MT7531 Reference Manual for Development Board rev 1.0, page 735
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the MACsec offloading preparation phase was removed from the
MACsec core implementation as well as from drivers implementing it, we
can safely remove the flag representing it.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware offloading in MACsec was initially supported using 2 phases.
This was proposed in the RFC as this could have allowed easier fallback
to the software implementation if the hardware did not support a feature
or had enough entries already. But this fallback wasn't implemented and
might not be a good idea after all. In addition it turned out this logic
didn't mapped well the hardware logic and device drivers were mostly
ignoring the preparation phase.
Let's remove this as it does not offer any advantage and is ignored by
drivers.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for removing the MACsec h/w offloading preparation phase,
make it a no-op in the Atlantic driver.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for removing the MACsec h/w offloading preparation phase,
make it a no-op in the MSCC phy driver.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SDM630 and SDM660 both use RPM (not RPMh) for managing the PM660 and
PM660L. The SDM670 uses RPMh to manage them as PMIC 4s. To support the
SDM670, add the PM660 and PM660L to the RPMh regulator driver.
Link: https://android.googlesource.com/kernel/msm/+/58064f13c0a436a82c35f2e3b5a122d874ae5846%5E%21/#F0
Link: https://android.googlesource.com/kernel/msm/+/f676d3d24f9d802bfe63369167c4a8cc162b8950%5E%21/#F3
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920223331.150635-3-mailingradian@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220923101632.19170-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This switches the driver to use gpiod API instead of legacy gpio API,
which will brings us close to removing of_get_gpio() and other
OF-specific old APIs.
No functional change intended beyond some differences in error messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/Yy07WbMAG4bPgYNd@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20220923101726.19420-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
sunxi SRAM controller fixes for
- loading/unloading
- claiming regions
- debugfs info
* tag 'sunxi-drivers-fixes-for-6.0-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
soc: sunxi: sram: Fix debugfs info for A64 SRAM C
soc: sunxi: sram: Fix probe function ordering issues
soc: sunxi: sram: Prevent the driver from being unbound
soc: sunxi: sram: Actually claim SRAM regions
Link: https://lore.kernel.org/r/YyeN0m78+m9nNEah@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom SoCs driver fixes for 6.0, please
pull the following:
- Florian fixes a double of_node_put() in the Broadcom STB Bus Interface
Unit driver
* tag 'arm-soc/for-6.0/drivers-fixes-v2' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: biuctrl: Avoid double of_node_put()
Link: https://lore.kernel.org/r/20220918205038.3017866-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/all/20220923095835.14647-1-shangxiaojing@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DMA allocated buffers are a precious resource. If there is no need for
DMA allocations, then it might be worth to use non-dma allocated
buffers.
After testing the gs_usb driver with and without DMA allocation, there
does not seem to be a significant change in latency or CPU utilization
either way. Therefore, DMA allocation is not necessary and removed.
Internal buffers used within urbs were managed and freed manually.
These buffers are no longer needed to be managed by the driver. The
URB_FREE_BUFFER flag, allows for the buffers in question to be
automatically freed.
Co-developed-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Vasanth Sadhasivan <vasanth.sadhasivan@samsara.com>
Link: https://lore.kernel.org/all/20220920154724.861093-2-rhett.aultman@samsara.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The candleLight community is working on switchable termination support
for the candleLight firmware. As the the Linux CAN framework supports
switchable termination add this feature to the gs_usb driver.
Devices supporting the feature should set the
GS_CAN_FEATURE_TERMINATION and implement the
GS_USB_BREQ_SET_TERMINATION and GS_USB_BREQ_GET_TERMINATION control
messages.
For now the driver assumes for activated termination the standard
termination value of 120Ω.
Link: https://lore.kernel.org/all/20220923074114.662045-1-mkl@pengutronix.de
Link: https://github.com/candle-usb/candleLight_fw/issues/92
Link: https://github.com/candle-usb/candleLight_fw/pull/109
Link: https://github.com/candle-usb/candleLight_fw/pull/108
Cc: Daniel Trevitz <daniel.trevitz@wika.com>
Cc: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Introduce a label to free the allocated candev in case of an error and
make use of if. Fix a memory leak if the extended bit timing cannot be
read. Extend the error messages to print the number of the failing
channel and the symbolic error name.
Link: https://lore.kernel.org/all/20220921193902.575416-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Convert the driver to use usb_control_msg_{send,recv}() instead of
usb_control_msg(). These functions allow the data to be placed on the
stack. This makes the driver a lot easier as we don't have to deal
with dynamically allocated memory.
Link: https://lore.kernel.org/all/20220921193902.575416-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
to dev
Most of the driver uses the variable "dev" to point to the struct
gs_can. Use the same name in gs_cmd_reset(), too. Rename gsdev to dev.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220921193902.575416-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On busy networks the CAN controller might receive CAN frames directly
after starting it but before the timecounter is setup. This will lead
to NULL pointer deref while converting the converting the CAN frame's
timestamp with the timecounter.
Close the race window by setting up the timecounter before starting
the CAN controller.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220921081329.385509-1-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The struct timecounter::cycle_last is a 64 bit variable, read by
timecounter_cyc2time(), and written by timecounter_read(). On 32 bit
architectures this is not atomic.
Add a spinlock to protect access to struct timecounter::cycle_last. In
the gs_usb_timestamp_read() callback the lock is dropped to execute a
sleeping synchronous USB transfer. This is safe, as the variable we
want to protect is accessed during this call.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-3-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
usb_control_msg_recv()
The 2nd argument of usb_control_msg_recv() is the "endpoint",
usb_control_msg_recv() will internally convert the endpoint into a
pipe with usb_rcvctrlpipe().
In gs_usb_get_timestamp() not the endpoint "0" is passed, but the
pipe. This worked by accident as endpoint is a __u8 and the lowest 8
bits of the pipe are 0. Fix this copy/paste error by using the correct
endpoint of "0".
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-2-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When GEM is in SGMII mode and disabled as a wakeup source, the power
management controller can power down the entire full power domain(FPD)
if none of the FPD devices are in use.
Incase of FPD off, there are below ethernet link up issues on non-wakeup
suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the
resume path which reinitializes PS GTR SGMII lanes.
$ echo +20 > /sys/class/rtc/rtc0/wakealarm
$ echo mem > /sys/power/state
After resume:
$ ifconfig eth0 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
SIOCSIFFLAGS: Connection timed out
phy phy-fd400000.phy.0: phy poweron failed --> -110
Fixes: 8b73fa3ae02b ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lan966x switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. Add support for TAS configuration on
egress port of lan966x switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add registers that are used by taprio to configure the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement mqprio qdisc support using tc command.
The HW supports 8 priority queues from highest (7) to lowest (0).
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a define for the number of priority queues on lan966x. Because there
will be more checks for this, so instead of using hardcoded value all
over the place add a define for this.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ->ring_idx_mask variable is a u64 so static checkers, Smatch in
this case, complain if the BIT() is not also a u64.
drivers/gpu/drm/virtio/virtgpu_ioctl.c:50 virtio_gpu_fence_event_create()
warn: should '(1 << ring_idx)' be a 64 bit type?
Fixes: cd7f5ca33585 ("drm/virtio: implement context init: add virtio_gpu_fence_event")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/YygN7jY0GdUSQSy0@kili
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Since qxl_io_reset(qdev) will be called immediately
after qxl_ring_create() been called,
and parameter like notify_on_prod will be set to default value.
So the call to qxl_ring_init_hdr() before becomes meaningless.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Suggested-by: Ming Xie<xieming@kylinos.cn>
Link: http://patchwork.freedesktop.org/patch/msgid/20220920065023.1633303-1-zhouzongmin@kylinos.cn
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
use kstrdup instead of open-coding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds support for not enabling carrier during TUNSETIFF
interface creation by specifying the IFF_NO_CARRIER flag.
Our tests make heavy use of tun interfaces. In some scenarios, the test
process creates the interface but another process brings it up after the
interface is discovered via netlink notification. In that case, it is
not possible to create a tun/tap interface with carrier off without it
racing against the bring up. Immediately setting carrier off via
TUNSETCARRIER is still too late.
Signed-off-by: Patrick Rohr <prohr@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read link status from SGMII PCS for in-band managed 2500Base-X and
1000Base-X connection on a MAC port of the MT7531. This is needed to
get the SFP cage working which is connected to SGMII interface of
port 5 of the MT7531 switch IC on the Bananapi BPi-R3 board.
While at it also handle an_complete for both the autoneg and the
non-autoneg codepath.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching for phys similar to the AQR107. We
assume that all phys using aqr107_read_status support rate matching.
However, it could be possible to determine support based on the firmware
revision if there are phys discovered which do not support rate
matching. However, as rate matching is advertised in the datasheets for
these phys, I suspect it is supported most boards.
Despite the name, the "config" registers are updated with the current
rate matching method (if any). Because they appear to be updated
automatically, I don't know if these registers can be used to disable
rate matching.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we are using CPU_PM_CPU_IDLE_ENTER_PARAM() for all SBI HSM
suspend types so retentive suspend types are also treated non-retentive
and kernel will do redundant additional work for these states.
The BIT[31] of SBI HSM suspend types allows us to differentiate between
retentive and non-retentive suspend types so we should use this BIT
to call appropriate CPU_PM_CPU_IDLE_ENTER_xyz() macro.
Fixes: 6abf32f1d9c5 ("cpuidle: Add RISC-V SBI CPU idle driver")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Link: https://lore.kernel.org/r/20220718084553.2056169-1-apatel@ventanamicro.com/
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
These are documented in the AQR115 register reference. I haven't tested
them, but perhaps they'll be useful to someone.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Link: https://lore.kernel.org/r/20220908130754.34999-1-wangjianli@cdjrlc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Waiting to 5 seconds in case of missing VMBus ACPI device is redundant as the
device is either present already or won't be available at all.
This patch enforces synchronous probing to make sure the bus traversal,
happening upon driver registering will either find the device (if present) or
not spend any additional time if device is absent.
Signed-off-by: Stanislav Kinsburskiy <stanislav.kinsburskiy@gmail.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Stephen Hemminger <sthemmin@microsoft.com>
CC: Wei Liu <wei.liu@kernel.org>
CC: Dexuan Cui <decui@microsoft.com>
CC: linux-hyperv@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/166378554568.581670.1124852716698789244.stgit@skinsburskii-cloud-desktop.internal.cloudapp.net
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Since the most that's mixed into the pool is sizeof(long)*2, don't
credit more than that many bytes of entropy.
Fixes: e3e33fc2ea7f ("random: do not use input pool from hard IRQs")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
pci_ids.h already defines PCI_VENDOR_ID_MICROSOFT, and is included via
linux/pci.h. Use the define instead of the magic number.
Signed-off-by: Easwar Hariharan <easwar.hariharan@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1663625084-2518-2-git-send-email-eahariha@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
drivers/hv/vmbus_drv.c:1587: warning: expecting prototype for __vmbus_child_driver_register(). Prototype was for __vmbus_driver_register() instead.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2210
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220919063815.1881-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
If a hwrng source does not provide an entropy estimate, it currently
does not contribute at all to the CRNG. In order to help fix this, in
case add_hwgenerator_randomness() is called with the entropy parameter
set to zero, go to sleep until one reseed interval has passed.
While the hwrng thread currently only runs under conditions where this
is non-zero, this change is not harmful and prepares for future updates
to the hwrng core.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Mix in randomness from hw-rng sources more frequently during early
boot, approximately once for every rng reseed.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
