| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If there are error flags in the aux transaction return
-EIO rather than -EBUSY. -EIO restarts the whole transaction
while -EBUSY jus retries. Fixes problematic aux transfers.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80684
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Commit e80991773 ("dm mpath: push back requests instead of queueing")
modified multipath_busy() to return true if !pg_ready(). pg_ready()
checks the current state of the multipath device and may return false
even if a new IO is needed to change the state.
Bart Van Assche reported that he had multipath IO lockup when he was
performing cable pull tests. Analysis showed that the multipath
device had a single path group with both paths active, but that the
path group itself was not active. During the multipath device state
transitions 'queue_io' got set but nothing could clear it. Clearing
'queue_io' only happens in __choose_pgpath(), but it won't be called
if multipath_busy() returns true due to pg_ready() returning false
when 'queue_io' is set.
As such the !pg_ready() check in multipath_busy() is wrong because new
IO will not be sent to multipath target and the multipath state change
won't happen. That results in multipath IO lockup.
The intent of multipath_busy() is to avoid unnecessary cycles of
dequeue + request_fn + requeue if it is known that the multipath
device will requeue.
Such "busy" situations would be:
- path group is being activated
- there is no path and the multipath is setup to requeue if no path
Fix multipath_busy() to return "busy" early only for these specific
situations.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.15
|
|
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn>
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Jana Saout <jana@saout.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The commit 2c140a246dc ("dm: allow remove to be deferred") introduced a
deferred removal feature for the device mapper. When this feature is
used (by passing a flag DM_DEFERRED_REMOVE to DM_DEV_REMOVE_CMD ioctl)
and the user tries to remove a device that is currently in use, the
device will be removed automatically in the future when the last user
closes it.
Device mapper used the system workqueue to perform deferred removals.
However, some targets (dm-raid1, dm-mpath, dm-stripe) flush work items
scheduled for the system workqueue from their destructor. If the
destructor itself is called from the system workqueue during deferred
removal, it introduces a possible deadlock - the workqueue tries to flush
itself.
Fix this possible deadlock by introducing a new workqueue for deferred
removals. We allocate just one workqueue for all dm targets. The
ability of dm targets to process IOs isn't dependent on deferred removal
of unused targets, so a deadlock due to shared workqueue isn't possible.
Also, cleanup local_init() to eliminate potential for returning success
on failure.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
|
|
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-cpufreq:
cpufreq: Makefile: fix compilation for davinci platform
intel_pstate: Set CPU number before accessing MSRs
intel_pstate: Update documentation of {max,min}_perf_pct sysfs files
intel_pstate: don't touch turbo bit if turbo disabled or unavailable.
intel_pstate: Fix setting VID
|
|
* acpi-video:
ACPI / video: Add Acer TravelMate B113 to native backlight blacklist
ACPI / video: Add Dell Inspiron 5737 to the blacklist
ACPI / i915: ignore firmware requests for backlight change
|
|
* acpi-ec:
ACPI / EC: Free saved_ec on error exit path
ACPI / EC: Add detailed fields debugging support of EC_SC(R).
ACPI / EC: Update revision due to recent changes
ACPI / EC: Fix race condition in ec_transaction_completed()
ACPI / EC: Remove duplicated ec_wait_ibf0() waiter
ACPI / EC: Add asynchronous command byte write support
ACPI / EC: Avoid race condition related to advance_transaction()
|
|
* acpi-resources:
ACPI / resources: only reject zero length resources based at address zero
* acpi-ac:
Revert "ACPI / AC: Remove AC's proc directory."
* acpi-scan:
ACPI / PNP: add soc_button_array device ID to PNP IDs list
* acpi-battery:
ACPI / battery: fix wrong value of capacity_now reported when fully charged
ACPI / battery: Retry to get battery information if failed during probing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Nothing too interesting. All fixes are ahci_platform related"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode command.
libahci: export ahci_qc_issue() and ahci_start_fix_rx()
ata: ahci_imx: warn when disabling ahci link
ahci: disable ncq feature for hisilicon sata
ahci: imx: manage only sata_ref_clk in imx_sata_enable[disable]
libahci_platform: Fail when PHY required but PHY support disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c build fix and cleanup from Wolfram Sang:
"One buildfix for the i2c subsystem. While here, I decided to add the
header cleanup as well"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6i-p2wi: Remove duplicate inclusion of module.h
i2c: mux: pca954x: fix dependencies
|
|
Pull crypto fixes from Herbert Xu:
"This push fixes an error in sha512_ssse3 that leads to incorrect
output as well as a memory leak in caam_jr when the module is
unloaded"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix memleak in caam_jr module
crypto: sha512_ssse3 - fix byte count to bit count conversion
|
|
This patch fixes a memory leak that appears when caam_jr module is unloaded.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Fixes for regressions and black screens, cc: stable where applicapable
(the last minute rebase was to sprinkle missing stable tags). A bit more
than what I'd wish for, but excluding vlv and that the first 3 patches are
just quirks for 1 regression it looks much better.
There's still a "oops, lost dithering" issue on older platforms open. I'm
working on a fix for that now but didn't want to delay this pile.
* tag 'drm-intel-fixes-2014-07-09' of git://anongit.freedesktop.org/drm-intel:
drm/i915/vlv: T12 eDP panel timing enforcement during reboot
drm/i915: Only unbind vgacon, not other console drivers
drm/i915: Don't clobber the GTT when it's within stolen memory
drm/i915/vlv: Update the DSI ULPS entry/exit sequence
drm/i915/vlv: DPI FIFO empty check is not needed
drm/i915: Toshiba CB35 has a controllable backlight
drm/i915: Acer C720 and C720P have controllable backlights
drm/i915: quirk asserts controllable backlight presence, overriding VBT
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
A couple of DP regression fixes, kepler memory reclocking fixes, and a fix for an annoying display issue that can pop up on resume.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
|
|
Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f36fdb9f0266 (i8k: Force SMM to run on CPU 0) adds support
for multi-core CPUs to the driver. Unfortunately, that causes it
to fail loading if compiled without SMP support, at least on
32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell
signature", and function i8k_smm is found to return -EINVAL.
Testing revealed that the culprit is the missing return value check
of set_cpus_allowed_ptr.
Fixes: f36fdb9f0266 (i8k: Force SMM to run on CPU 0)
Reported-by: Jim Bos <jim876@xs4all.nl>
Tested-by: Jim Bos <jim876@xs4all.nl>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the
Testo 435-4 uses this, likely other gear as well.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Just a fix for the device reset path and an email address update.
Virtualization
- Fix "wait for pending transactions" for PCI AF reset (Alex
Williamson)
Miscellaneous
- Update mx6 PCI driver maintainer email (Fabio Estevam)"
* tag 'pci-v3.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update mx6 PCI driver maintainer's email
PCI: Fix unaligned access in AF transaction pending test
|
|
Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Starting with Win8, we have implemented several optimizations to improve the
scalability and performance of the VMBUS transport between the Host and the
Guest. Some of the non-performance critical services cannot leverage these
optimization since they only read and process one message at a time.
Make adjustments to the callback dispatch code to account for the way
non-performance critical drivers handle reading of the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The soc_button_array PNP driver was introduced in 3.15.
But in commit eec15edbb0e1 (ACPI / PNP: use device ID list for
PNPACPI device enumeration), when reworking the PNPACPI device
enumeration, we missed the soc_button_array device ID.
This results in a regression in 3.16-rc1 that soc_button_array
pnp device fails to be enumerated.
Fix the problem by adding soc_button_array device ID into the
acpi_pnp scan handler's ID list.
Fixes: eec15edbb0e1 (ACPI / PNP: use device ID list for PNPACPI device enumeration)
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The console subsystem only provides a function to switch to a given
console, but we want to actually only switach away from vgacon.
Unconditionally switching to the dummy console resulted in switching
away from fbcon in multi-gpu setups when other gpu drivers are loaded
before i915.
Then either the reinitialization of fbcon when i915 registers its
fbdev emulation or the teardown of the fbcon driver killed the
machine. So only switch to the dummy console when it's required.
Kudos to Chris for the original idea, I've only refined it a bit to
still unregister vgacon even when it's currently unused.
This regression has been introduced in
commit a4de05268e674e8ed31df6348269e22d6c6a1803
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 5 16:20:46 2014 +0200
drm/i915: Kick out vga console
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On most gen2-4 platforms the GTT can be (or maybe always is?)
inside the stolen memory region. If that's the case, reduce the
size of the stolen memory appropriately to make make sure we
don't clobber the GTT.
v2: Deal with gen4 36 bit physical address
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We should keep DEVICE_READY bit set in the ULPS enter sequence. In
exit sequence also we should set DEVICE_READY, but thats causing
blankout for me. Also exit sequence is simplified as per hw team
recommendation.
This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
While sending DPI SHUTDOWN command, we cannot wait for FIFO empty as
pipes are not disabled at that time. In case of MIPI we disable port
first and send SHUTDOWN command while pipe is still running and FIFOs
will not be empty, causing spurious error log
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The Toshiba CB35 Chromebook (with Celeron 2955U CPU) has a controllable
backlight although its VBT reports otherwise. Apply quirk to ignore the
backlight presence check during backlight setup.
Patch tested by author on Toshiba CB35.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The Acer C720 and C720P Chromebooks (with Celeron 2955U CPU) have a
controllable backlight although their VBT reports otherwise. Apply quirk
to ignore the backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
commit c675949ec58ca50d5a3ae3c757892f1560f6e896
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204da0 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204da0 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.
Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commtit 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to
drivers/cpufreq) this added dependancy only for CONFIG_ARCH_DAVINCI_DA850
where as davinci_cpufreq_init() call is used by all davinci platform.
This patch fixes following build error:
arch/arm/mach-davinci/built-in.o: In function `davinci_init_late':
:(.init.text+0x928): undefined reference to `davinci_cpufreq_init'
make: *** [vmlinux] Error 1
Fixes: 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to drivers/cpufreq)
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third round of iio fixes for the 3.16 cycle.
* Lots of hid sensors component drivers had a bug due to a local variable
whose name suggested it was returned from the read_raw function not
infact being returned (ret vs ret_type). Fixed and unused ret removed.
* Block a possible race condition in tcs3472 by locking around some
dependant i2c messages.
* Fix bug in the am335x driver fifo setup that occurs if the final
channel enabled takes certain values.
|
|
Since AI lines could be selected at will (linux-3.11) the sending
and receiving ends of the FIFO does not agree about what step is used
for a line. It only works if the last lines are used, like 5,6,7,
and fails if ie 2,4,6 is selected in DT.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Tested-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix a number of zero-day bugs, mostly found with module test scripts.
Nothing major, but potentially annoying and worthwhile to fix"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (adc128d818) Drop write support on inX_input attributes
hwmon: (emc2103) Clamp limits instead of bailing out
hwmon: (adm1031) Fix writes to limit registers
hwmon: (adm1021) Fix cache problem when writing temperature limits
hwmon: (adm1029) Ensure the fan_div cache is updated in set_fan_div
hwmon: (amc6821) Fix permissions for temp2_input
hwmon: (ntc_thermistor) Correct information printed during probe
|
|
In xennet_disconnect_backend(), netif_carrier_off() was called once
per queue when it needs to only be called once.
The queue locking around the netif_carrier_off() call looked very
odd. I think they were supposed to synchronize any NAPI instances with
the expectation that no further NAPI instances would be scheduled
because of the carrier being off (see the check in
xennet_rx_interrupt()). But I can't easily tell if this works
correctly.
Instead, add a napi_synchronize() call after disabling the interrupts.
This is obviously correct as with no Rx interrupts, no further NAPI
instances will be scheduled.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nesting of the per-queue rx_lock and tx_lock in xennet_connect()
is confusing to both humans and lockdep. The locking is safe because
this is the only place where the locks are nested in this way but
lockdep still warns.
Instead of adding the missing lockdep annotations, refactor the
locking to avoid the confusing nesting. This is still safe, because
the xenbus connection state changes are all serialized by the xenwatch
thread.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mode command.
This patch fixes the dma state machine lockup due to the processing
of IDENTIFY DEVICE PIO mode command. The X-Gene AHCI controller
has an errata in which it cannot clear the BSY bit after the PIO setup
FIS. The dma state machine enters CMFatalErrorUpdate state and locks
up. This patch also removes the dma restart workaround from the read_id
function as the read_id function is only called by libata layer for
ATA_INTERNAL commands. But for some cases eg: PORT MULTIPLIER
and udev, the framework will enumerate using SCSI commands and it will
not call read_id function.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The subsequent patch will make use of them.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The add_vxlan_port ndo driver code was wrongly testing whether HW vxlan offloads
are supported by the device instead of checking if they are currently enabled.
This causes the driver to configure the HW parser to conduct matching for vxlan
packets but since no steering rules were set, vxlan packets are dropped on RX.
Fix that by doing the right test, as done in the del_vxlan_port ndo handler.
Fixes: 1b136de ('net/mlx4: Implement vxlan ndo calls')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes-2 for v3.16" from Kukjin Kim:
- fix the check for SMP configuration with using CONFIG_SMP
not just SMP
- fix the number of pwm-cells for exynos4 pwm
- fix ftrace for exynos_mct
- register exynos_mct for stable udely
- fix secondary boot addr for secure mode for exynos SoCs
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update secondary boot addr for secure mode
clocksource: exynos_mct: Register the timer for stable udelay
clocksource: exynos_mct: Fix ftrace
ARM: dts: fix pwm-cells in pwm node for exynos4
ARM: EXYNOS: Fix the check for non-smp configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
|
