summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2022-05-21i2c: npcm: Handle spurious interruptsTali Perry
On some platforms in rare cases (1 to 100,000 transactions), the i2c gets a spurious interrupt which means that we enter an interrupt but in the interrupt handler we don't find any status bit that points to the reason we got this interrupt. This may be a case of a rare HW issue or signal integrity issue that is still under investigation. In order to overcome this we are doing the following: 1. Disable incoming interrupts in master mode only when slave mode is not enabled. 2. Clear end of busy (EOB) after every interrupt. 3. Clear other status bits (just in case since we found them cleared) 4. Return correct status during the interrupt that will finish the transaction. On next xmit transaction if the bus is still busy the master will issue a recovery process before issuing the new transaction. Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-21i2c: npcm: Correct register access widthTyrone Ting
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always incorrect, but simply didn't cause a visible error on the 32-bit machine. On the 64-bit machine, the kernel message reports that ESR value is 0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that it's the alignment fault. SMBnCTL3's address is 0xE. Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-21i2c: npcm: Add tx complete counterTali Perry
tx_complete counter is used to indicate successful transaction count. Similar counters for failed tx were previously added. Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-21i2c: npcm: Fix timeout calculationTali Perry
Use adap.timeout for timeout calculation instead of hard-coded value of 35ms. Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-21i2c: npcm: Remove unused variable clk_regmapTali Perry
Remove unused variable clk_regmap. Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-21i2c: npcm: Change the way of getting GCR regmapTali Perry
Change the way of getting NPCM system manager reigster (GCR) and still maintain the old mechanism as a fallback if getting nuvoton,sys-mgr fails while working with the legacy devicetree file. Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-05-20Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fixes from Stephen Boyd: "Three clk driver fixes to close out the release - Fix a divider calculation breaking boot on Broadcom bcm2835 - Fix HDMI output on Tanix TX6 mini board by reverting a patch - Fix clk_set_rate_range() calls on at91 by considering the range while calculating the divisor" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: at91: generated: consider range when calculating best rate Revert "clk: sunxi-ng: sun6i-rtc: Add support for H6" clk: bcm2835: fix bcm2835_clock_choose_div
2022-05-20Merge tag 'drm-fixes-2022-05-21' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "Few final fixes for 5.18, one amdgpu, core dp mst leak fix, dma-buf two fixes, and i915 has a few fixes, one for a regression on older GM45 chipsets, dma-buf: - ioctl userspace use fix - fix dma-buf sysfs name generation core: - dp/mst leak fix amdgpu: - suspend/resume regression fix i915: - fix for #5806: GPU hangs and display artifacts on Intel GM45 - reject DMC with out-of-spec MMIO - correctly mark guilty contexts on GuC reset" * tag 'drm-fixes-2022-05-21' of git://anongit.freedesktop.org/drm/drm: drm/i915: Use i915_gem_object_ggtt_pin_ww for reloc_iomap drm/amd: Don't reset dGPUs if the system is going to s2idle drm/dp/mst: fix a possible memory leak in fetch_monitor_name() dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace i915/guc/reset: Make __guc_reset_context aware of guilty engines drm/i915/dmc: Add MMIO range restrictions dma-buf: ensure unique directory name for dmabuf stats
2022-05-20clk: bcm: rpi: Use correct order for the parameters of devm_kcalloc()Christophe JAILLET
We should have 'n', then 'size', not the opposite. This is harmless because the 2 values are just multiplied, but having the correct order silence a (unpublished yet) smatch warning. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/49d726d11964ca0e3757bdb5659e3b3eaa1572b5.1653081643.git.christophe.jaillet@wanadoo.fr Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add safe mux managementGabriel Fernandez
Some muxes need to set a the safe position when clock is off. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-12-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add multi mux functionGabriel Fernandez
Some RCC muxes can manages two output clocks with same register. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-11-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add all STM32MP13 kernel clocksGabriel Fernandez
Complete all kernel clocks of stm32mp13. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-10-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add all STM32MP13 peripheral clocksGabriel Fernandez
All peripheral clocks are mainly based on stm32_gate clock. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-9-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: manage secured clocksGabriel Fernandez
Don't register a clock if this clock is secured. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-8-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add composite clockGabriel Fernandez
Just to introduce management of stm32 composite clock. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-7-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add stm32 divider clockGabriel Fernandez
Just to introduce management of a stm32 divider clock Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-6-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add stm32_gate managementGabriel Fernandez
Just to introduce management of a stm32 gate clock. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-5-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32mp13: add stm32_mux clock managementGabriel Fernandez
Just to introduce management of a stm32 mux clock. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-4-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: stm32: Introduce STM32MP13 RCC drivers (Reset Clock Controller)Gabriel Fernandez
This driver manages Reset and Clock of STM32MP13 soc. It uses a clk-stm32-core module to manage stm32 gate, mux and divider for STM32MP13 and for new future soc. All gates, muxes, dividers are identify by an index and information are stored in array (register address, shift, with, flags...) This is useful when we have two clocks with the same gate or when one mux manages two output clocks. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Link: https://lore.kernel.org/r/20220516070600.7692-3-gabriel.fernandez@foss.st.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: ti: clkctrl: replace usage of found with dedicated list iterator variableJakob Koschel
To move the list iterator variable into the list_for_each_entry_*() macro in the future it should be avoided to use the list iterator variable after the loop body. To *never* use the list iterator variable after the loop it was concluded to use a separate iterator variable instead of a found boolean [1]. This removes the need to use a found variable and simply checking if the variable was set, can determine if the break/goto was hit. Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Link: https://lore.kernel.org/r/20220324071019.59483-1-jakobkoschel@gmail.com Tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20clk: ti: composite: Prefer kcalloc over open coded arithmeticLen Baker
As noted in the "Deprecated Interfaces, Language Features, Attributes, and Conventions" documentation [1], size calculations (especially multiplication) should not be performed in memory allocator (or similar) function arguments due to the risk of them overflowing. This could lead to values wrapping around and a smaller allocation being made than the caller was expecting. Using those allocations could lead to linear overflows of heap memory and other misbehaviors. So, use the purpose specific kcalloc() function instead of the argument size * count in the kzalloc() function. [1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments Signed-off-by: Len Baker <len.baker@gmx.com> Link: https://lore.kernel.org/r/20210904131714.2312-1-len.baker@gmx.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-05-20wwan: iosm: use a flexible array rather than allocate short objectsJakub Kicinski
GCC array-bounds warns that ipc_coredump_get_list() under-allocates the size of struct iosm_cd_table *cd_table. This is avoidable - we just need a flexible array. Nothing calls sizeof() on struct iosm_cd_list or anything that contains it. Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com> Link: https://lore.kernel.org/r/20220520060013.2309497-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20hv_netvsc: Fix potential dereference of NULL pointerYongzhi Liu
The return value of netvsc_devinfo_get() needs to be checked to avoid use of NULL pointer in case of an allocation failure. Fixes: 0efeea5fb153 ("hv_netvsc: Add the support of hibernation") Signed-off-by: Yongzhi Liu <lyz_cs@pku.edu.cn> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/1652962188-129281-1-git-send-email-lyz_cs@pku.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20net: mscc: fix the alignment in ocelot_port_fdb_del()Alaa Mohamed
align the extack argument of the ocelot_port_fdb_del() function. Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com> Link: https://lore.kernel.org/r/20220520002040.4442-1-eng.alaamohamedsoliman.am@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20net: vxlan: Fix kernel coding styleAlaa Mohamed
The continuation line does not align with the opening bracket and this patch fix it. Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com> Link: https://lore.kernel.org/r/20220520003614.6073-1-eng.alaamohamedsoliman.am@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20eth: bnxt: make ulp_id unsigned to make GCC 12 happyJakub Kicinski
GCC array bounds checking complains that ulp_id is validated only against upper bound. Make it unsigned. Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20220520061955.2312968-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20net: wwan: t7xx: use GFP_ATOMIC under spin lock in t7xx_cldma_gpd_set_next_ptr()Yang Yingliang
Sometimes t7xx_cldma_gpd_set_next_ptr() is called under spin lock, so add 'gfp_mask' parameter in t7xx_cldma_gpd_set_next_ptr() to pass the flag. Fixes: 39d439047f1d ("net: wwan: t7xx: Add control DMA interface") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/20220519032108.2996400-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20net: tulip: fix build with CONFIG_GSCRolf Eike Beer
Fix typo which breaks build for parisc. Fixes: 3daebfbeb455 ("net: tulip: convert to devres") Reported-by: Linux Kernel Functional Testing <lkft@linaro.org> Link: https://lore.kernel.org/all/CA+G9fYuCzU5VZ_nc+6NEdBXJdVCH=J2SB1Na1G_NS_0BNdGYtg@mail.gmail.com/ Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Link: https://lore.kernel.org/r/4719560.GXAFRqVoOG@eto.sf-tec.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20amt: fix memory leak for advertisement messageTaehee Yoo
When a gateway receives an advertisement message, it extracts relay information and then it should be freed. But the advertisement handler doesn't free it. So, memory leak would occur. Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20amt: fix gateway mode stuckTaehee Yoo
If a gateway can not receive any response to requests from a relay, gateway resets status from SENT_REQUEST to INIT and variable about a relay as well. And then it should start the full establish step from sending a discovery message and receiving advertisement message. But, after failure in amt_req_work() it continues sending a request message step with flushed(invalid) relay information and sets SENT_REQUEST. So, a gateway can't be established with a relay. In order to avoid this situation, it stops sending the request message step if it fails. Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20net: stmmac: fix out-of-bounds access in a selftestJakub Kicinski
GCC 12 points out that struct tc_action is smaller than struct tcf_action: drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c: In function ‘stmmac_test_rxp’: drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1132:21: warning: array subscript ‘struct tcf_gact[0]’ is partly outside array bounds of ‘unsigned char[272]’ [-Warray-bounds] 1132 | gact->tcf_action = TC_ACT_SHOT; | ^~ Fixes: ccfc639a94f2 ("net: stmmac: selftests: Add a selftest for Flexible RX Parser") Link: https://lore.kernel.org/r/20220519004305.2109708-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-20sfc/siena: Remove duplicate check on segmentsMartin Habets
Siena only supports software TSO. This means more code can be deleted, as pointed out by the Smatch static checker warning: drivers/net/ethernet/sfc/siena/tx.c:184 __efx_siena_enqueue_skb() warn: duplicate check 'segments' (previous on line 158) Fixes: 956f2d86cb37 ("sfc/siena: Remove build references to missing functionality") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/kernel-janitors/YoH5tJMnwuGTrn1Z@kili/ Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/165294463549.23865.4557617334650441347.stgit@palantir17.mph.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-21Merge tag 'drm-intel-fixes-2022-05-20' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes - fix for #5806: GPU hangs and display artifacts on 5.18-rc3 on Intel GM45 - reject DMC with out-of-spec MMIO (Cc: stable) - correctly mark guilty contexts on GuC reset. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/YocqqvG6PbYx3QgJ@jlahtine-mobl.ger.corp.intel.com
2022-05-21Merge tag 'drm-misc-fixes-2022-05-20' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Fix for a memory leak in dp_mst, a (userspace) build fix for DMA_BUF_SET_NAME defines and a directory name generation fix for dmabuf stats Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220520072408.cpjzy2taugagvrh7@houat
2022-05-20cxl/port: Enable HDM Capability after validating DVSEC RangesDan Williams
CXL memory expanders that support the CXL 2.0 memory device class code include an "HDM Decoder Capability" mechanism to supplant the "CXL DVSEC Range" mechanism originally defined in CXL 1.1. Both mechanisms depend on a "mem_enable" bit being set in configuration space before either mechanism activates. When the HDM Decoder Capability is enabled the CXL DVSEC Range settings are ignored. Previously, the cxl_mem driver was relying on platform-firmware to set "mem_enable". That is an invalid assumption as there is no requirement that platform-firmware sets the bit before the driver sees a device, especially in hot-plug scenarios. Additionally, ACPI-platforms that support CXL 2.0 devices also support the ACPI CEDT (CXL Early Discovery Table). That table outlines the platform permissible address ranges for CXL operation. So, there is a need for the driver to set "mem_enable", and there is information available to determine the validity of the CXL DVSEC Ranges. Arrange for the driver to optionally enable the HDM Decoder Capability if "mem_enable" was not set by platform firmware, or the CXL DVSEC Range configuration was invalid. Be careful to only disable memory decode if the kernel was the one to enable it. In other words, if CXL is backing all of kernel memory at boot the device needs to maintain "mem_enable" and "HDM Decoder enable" all the way up to handoff back to platform firmware (e.g. ACPI S5 state entry may require CXL memory to stay active). Fixes: 560f78559006 ("cxl/pci: Retrieve CXL DVSEC memory info") Cc: Dan Carpenter <dan.carpenter@oracle.com> [dan: fix early terminiation of range-allowed loop] Cc: Ariel Sibley <ariel.sibley@microchip.com> [ariel: Memory_size must be non-zero] Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Link: https://lore.kernel.org/r/165307136375.2499769.861793697156744166.stgit@dwillia2-xfh Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2022-05-20USB: new quirk for Dell Gen 2 devicesMonish Kumar R
Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen 2 device to not fail during enumeration. Found this bug on own testing Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-20Merge tag 'usb-serial-5.19-rc1' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next Johan writes: USB-serial updates for 5.19-rc1 Here are the USB-serial updates for 5.19-rc1, including: - a workaround for pl2303 devices with unexpected bcdUSB - a new modem device id Included is also a printk clean up. All but the modem-id commit have been in linux-next with no reported issues. * tag 'usb-serial-5.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add Quectel BG95 modem USB: serial: pl2303: fix type detection for odd device USB: serial: ftdi_sio: clean up printk format specifier
2022-05-20Revert "speakup: Generate speakupmap.h automatically"Greg Kroah-Hartman
This reverts commit 6646b95aab5f62c049f1416a3801dec5432c348b. Stephen reports that it breaks the build for him so revert it for now. Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/r/20220520194637.03824f7f@canb.auug.org.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-20Merge tag 'gpio-fixes-for-v5.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fixes from Bartosz Golaszewski: - fix bitops logic in gpio-vf610 - return an error if the user tries to use inverted polarity in gpio-mvebu * tag 'gpio-fixes-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpio: mvebu/pwm: Refuse requests with inverted polarity gpio: gpio-vf610: do not touch other bits when set the target bit
2022-05-20Merge tag 'mmc-v5.18-rc4-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fix from Ulf Hansson: "MMC core: - Fix busy polling for MMC_SEND_OP_COND again" * tag 'mmc-v5.18-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: core: Fix busy polling for MMC_SEND_OP_COND again
2022-05-20hwmon: (pmbus/ltc2978) Add chip specific write_byte_dataMårten Lindahl
Several of the manuals for devices supported by this driver describes the need for a minimum wait time before the chip is ready to receive next command. This wait time is already implemented in the driver as a ltc_wait_ready function with a driver defined wait time of 100 ms, and is considered for specific devices before reading/writing data on the pmbus. Since this driver uses the default pmbus_regulator_ops for the enable/ disable/is_enabled functions we should add a driver specific callback for write_byte_data to prevent bypassing the wait time recommendations for the following devices: ltc3880/ltc3882/ltc3883/ltc3884/ltc3886/ ltc3887/ltc3889/ltm4664/ltm4675/ltm4676/ltm4677/ltm4678/ltm4680/ltm4686/ ltm4700/ltc7880. Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20220428144039.2464667-4-marten.lindahl@axis.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (pmbus) Use _pmbus_read_byte_data with callbackMårten Lindahl
Some of the pmbus core functions uses pmbus_read_byte_data, which does not support driver callbacks for chip specific write operations. This could potentially influence some specific regulator chips that for example need a time delay before each data access. Lets use _pmbus_read_byte_data with callback check. Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20220428144039.2464667-3-marten.lindahl@axis.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (pmbus) Introduce and use write_byte_data callbackMårten Lindahl
Some of the pmbus core functions uses pmbus_write_byte_data, which does not support driver callbacks for chip specific write operations. This could potentially influence some specific regulator chips that for example need a time delay before each data access. Lets add support for driver callback with _pmbus_write_byte_data. Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20220428144039.2464667-2-marten.lindahl@axis.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) add PRIME X470-PRO boardEugene Shalygin
This board is supposed to be handled by the asus-wmi-sensors driver, but due to a buggy WMI implementation the driver and the official ASUS software make the BIOS hang together with fan controls [1, 2]. This driver complements values provided by the SIO chip and does not freeze the BIOS, as tested by a user [2]. [1] https://github.com/electrified/asus-wmi-sensors/blob/master/README.md [2] https://github.com/zeule/asus-ec-sensors/issues/12 Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427143001.1443605-5-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) add support for board familiesEugene Shalygin
DSDT code for AMD 400-series chipset shows that sensor addresses differ for this generation from those for the AMD 500-series boards. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427143001.1443605-4-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) implement locking via the ACPI global lockEugene Shalygin
For some board models ASUS uses the global ACPI lock to guard access to the hardware, so do we. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427143001.1443605-3-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (asus-ec-sensors) introduce ec_board_info struct for board dataEugene Shalygin
We need to keep some more information about the current board than just the sensors set, and with more boards to add the dmi id array grows quickly. Our probe code is always the same so let's switch to a custom test code and a custom board info array. That allows us to omit board vendor string (ASUS uses two strings that differ in case) in the board info and use case-insensitive comparison, and also do not duplicate sensor definitions for such board variants as " (WI-FI)" when sensors are identical to the base variant. Also saves a quarter of the module size by replacing big dmi_system_id structs with smaller ones. Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com> Link: https://lore.kernel.org/r/20220427143001.1443605-2-eugene.shalygin@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (occ) Delay hwmon registration until user requestEddie James
Instead of registering the hwmon device at probe time, use the existing "occ_active" sysfs file to control when the driver polls the OCC for sensor data and registers with hwmon. The reason for this change is that the SBE, which is the device by which the driver communicates with the OCC, cannot handle communications during certain system state transitions, resulting in unrecoverable system errors. Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20220427140443.11428-1-eajames@linux.ibm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (nct6775) Split core and platform driverZev Weiss
This splits the nct6775 driver into an interface-independent core and a separate platform driver that wraps inb/outb port I/O (or asuswmi methods) around that core. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Tested-by: Renze Nicolai <renze@rnplus.nl> Link: https://lore.kernel.org/r/20220427010154.29749-7-zev@bewilderbeest.net Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2022-05-20hwmon: (nct6775) Convert S_I* permissions macros to octalZev Weiss
Checkpatch has been warning about these for a while; the octal versions are both more comprehensible and more concise. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Link: https://lore.kernel.org/r/20220427010154.29749-6-zev@bewilderbeest.net Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
generated by cgit (git 2.34.1) at 2025-09-16 17:46:28 +0000