| Age | Commit message (Collapse) | Author |
|---|
|
Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
->lookup() in an encrypted directory begins as follows:
1. fscrypt_prepare_lookup():
a. Try to load the directory's encryption key.
b. If the key is unavailable, mark the dentry as a ciphertext name
via d_flags.
2. fscrypt_setup_filename():
a. Try to load the directory's encryption key.
b. If the key is available, encrypt the name (treated as a plaintext
name) to get the on-disk name. Otherwise decode the name
(treated as a ciphertext name) to get the on-disk name.
But if the key is concurrently added, it may be found at (2a) but not at
(1a). In this case, the dentry will be wrongly marked as a ciphertext
name even though it was actually treated as plaintext.
This will cause the dentry to be wrongly invalidated on the next lookup,
potentially causing problems. For example, if the racy ->lookup() was
part of sys_mount(), then the new mount will be detached when anything
tries to access it. This is despite the mountpoint having a plaintext
path, which should remain valid now that the key was added.
Of course, this is only possible if there's a userspace race. Still,
the additional kernel-side race is confusing and unexpected.
Close the kernel-side race by changing fscrypt_prepare_lookup() to also
set the on-disk filename (step 2b), consistent with the d_flags update.
Fixes: 28b4c263961c ("ext4 crypto: revalidate dentry after adding or removing the key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Make __d_move() clear DCACHE_ENCRYPTED_NAME on the source dentry. This
is needed for when d_splice_alias() moves a directory's encrypted alias
to its decrypted alias as a result of the encryption key being added.
Otherwise, the decrypted alias will incorrectly be invalidated on the
next lookup, causing problems such as unmounting a mount the user just
mount()ed there.
Note that we don't have to support arbitrary moves of this flag because
fscrypt doesn't allow dentries with DCACHE_ENCRYPTED_NAME to be the
source or target of a rename().
Fixes: 28b4c263961c ("ext4 crypto: revalidate dentry after adding or removing the key")
Reported-by: Sarthak Kukreti <sarthakkukreti@chromium.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Close some race conditions where fscrypt allowed rename() and link() on
ciphertext dentries that had been looked up just prior to the key being
concurrently added. It's better to return -ENOKEY in this case.
This avoids doing the nonsensical thing of encrypting the names a second
time when searching for the actual on-disk dir entries. It also
guarantees that DCACHE_ENCRYPTED_NAME dentries are never rename()d, so
the dcache won't have support all possible combinations of moving
DCACHE_ENCRYPTED_NAME around during __d_move().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Make various improvements to fscrypt dentry revalidation:
- Don't try to handle the case where the per-directory key is removed,
as this can't happen without the inode (and dentries) being evicted.
- Flag ciphertext dentries rather than plaintext dentries, since it's
ciphertext dentries that need the special handling.
- Avoid doing unnecessary work for non-ciphertext dentries.
- When revalidating ciphertext dentries, try to set up the directory's
i_crypt_info to make sure the key is really still absent, rather than
invalidating all negative dentries as the previous code did. An old
comment suggested we can't do this for locking reasons, but AFAICT
this comment was outdated and it actually works fine.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
->i_crypt_info starts out NULL and may later be locklessly set to a
non-NULL value by the cmpxchg() in fscrypt_get_encryption_info().
But ->i_crypt_info is used directly, which technically is incorrect.
It's a data race, and it doesn't include the data dependency barrier
needed to safely dereference the pointer on at least one architecture.
Fix this by using READ_ONCE() instead. Note: we don't need to use
smp_load_acquire(), since dereferencing the pointer only requires a data
dependency barrier, which is already included in READ_ONCE(). We also
don't need READ_ONCE() in places where ->i_crypt_info is unconditionally
dereferenced, since it must have already been checked.
Also downgrade the cmpxchg() to cmpxchg_release(), since RELEASE
semantics are sufficient on the write side.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The only reason the inode is being passed to fscrypt_get_ctx() is to
verify that the encryption key is available. However, all callers
already ensure this because if we get as far as trying to do I/O to an
encrypted file without the key, there's already a bug.
Therefore, remove this unnecessary argument.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Handling of extended interrupts (kickstart, wake-up, ram-clear) was
moved off to a work queue, but the interrupts aren't acknowledged
in the interrupt handler. This leads to a deadlock, if driver
is used with interrupts. To fix this we use a threaded interrupt, get rid
of the work queue and do locking with just the rtc mutex lock.
Fixes: aaaf5fbf56f1 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Pull KVM fixes from Paolo Bonzini:
"5.1 keeps its reputation as a big bugfix release for KVM x86.
- Fix for a memory leak introduced during the merge window
- Fixes for nested VMX with ept=0
- Fixes for AMD (APIC virtualization, NMI injection)
- Fixes for Hyper-V under KVM and KVM under Hyper-V
- Fixes for 32-bit SMM and tests for SMM virtualization
- More array_index_nospec peppering"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
KVM: fix spectrev1 gadgets
KVM: x86: fix warning Using plain integer as NULL pointer
selftests: kvm: add a selftest for SMM
selftests: kvm: fix for compilers that do not support -no-pie
selftests: kvm/evmcs_test: complete I/O before migrating guest state
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
KVM: x86: clear SMM flags before loading state while leaving SMM
KVM: x86: Open code kvm_set_hflags
KVM: x86: Load SMRAM in a single shot when leaving SMM
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
KVM: x86: Raise #GP when guest vCPU do not support PMU
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
svm/avic: Fix invalidate logical APIC id entry
Revert "svm: Fix AVIC incomplete IPI emulation"
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM: nVMX: always use early vmcs check when EPT is disabled
KVM: nVMX: allow tests to use bad virtual-APIC page address
...
|
|
These were found with smatch, and then generalized when applicable.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Instead of checking the upper values of the sequence number use an explicit
field in the dma_fence_ops structure to note if a sequence should be 32bit
or 64bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/299655/
|
|
Use the new xfer_atomic callback to check a newly introduced flag to
whitelist atomic transfers. This will report configurations which
worked accidently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We had the request to access devices very late when interrupts are not
available anymore multiple times now. Mostly to prepare shutdown or
reboot. Allow adapters to specify a specific callback for this case.
Note that we fall back to the generic {master|smbus}_xfer callback if
this new atomic one is not present. This is intentional to preserve the
previous behaviour and avoid regressions. Because there are drivers not
using interrupts or because it might have worked "accidently" before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch add perf_pmu_resched() a global function that can be called
to force rescheduling of events for a given PMU. The function locks
both cpuctx and task_ctx internally. This will be used by a subsequent
patch.
Signed-off-by: Stephane Eranian <eranian@google.com>
[ Simplified the calling convention. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Cc: nelson.dsouza@intel.com
Cc: tonyj@suse.com
Link: https://lkml.kernel.org/r/20190408173252.37932-2-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Upon reboot, the Acer TravelMate X514-51T laptop appears to complete the
shutdown process, but then it hangs in BIOS POST with a black screen.
The problem is intermittent - at some points it has appeared related to
Secure Boot settings or different kernel builds, but ultimately we have
not been able to identify the exact conditions that trigger the issue to
come and go.
Besides, the EFI mode cannot be disabled in the BIOS of this model.
However, after extensive testing, we observe that using the EFI reboot
method reliably avoids the issue in all cases.
So add a boot time quirk to use EFI reboot on such systems.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=203119
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux@endlessm.com
Link: http://lkml.kernel.org/r/20190412080152.3718-1-jian-hong@endlessm.com
[ Fix !CONFIG_EFI build failure, clarify the code and the changelog a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add support for the new samples attributes to the hwmon core.
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
It takes a fair amount of boiler plate code to add new sensors, add a
macro that can be used to specify simple static sensors.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Emit an audit record every time selected NTP parameters are modified
from userspace (via adjtimex(2) or clock_adjtime(2)). These parameters
may be used to indirectly change system clock, and thus their
modifications should be audited.
Such events will now generate records of type AUDIT_TIME_ADJNTPVAL
containing the following fields:
- op -- which value was adjusted:
- offset -- corresponding to the time_offset variable
- freq -- corresponding to the time_freq variable
- status -- corresponding to the time_status variable
- adjust -- corresponding to the time_adjust variable
- tick -- corresponding to the tick_usec variable
- tai -- corresponding to the timekeeping's TAI offset
- old -- the old value
- new -- the new value
Example records:
type=TIME_ADJNTPVAL msg=audit(1530616044.507:7): op=status old=64 new=8256
type=TIME_ADJNTPVAL msg=audit(1530616044.511:11): op=freq old=0 new=49180377088000
The records of this type will be associated with the corresponding
syscall records.
An overview of parameter changes that can be done via do_adjtimex()
(based on information from Miroslav Lichvar) and whether they are
audited:
__timekeeping_set_tai_offset() -- sets the offset from the
International Atomic Time
(AUDITED)
NTP variables:
time_offset -- can adjust the clock by up to 0.5 seconds per call
and also speed it up or slow down by up to about
0.05% (43 seconds per day) (AUDITED)
time_freq -- can speed up or slow down by up to about 0.05%
(AUDITED)
time_status -- can insert/delete leap seconds and it also enables/
disables synchronization of the hardware real-time
clock (AUDITED)
time_maxerror, time_esterror -- change error estimates used to
inform userspace applications
(NOT AUDITED)
time_constant -- controls the speed of the clock adjustments that
are made when time_offset is set (NOT AUDITED)
time_adjust -- can temporarily speed up or slow down the clock by up
to 0.05% (AUDITED)
tick_usec -- a more extreme version of time_freq; can speed up or
slow down the clock by up to 10% (AUDITED)
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Emit an audit record whenever the system clock is changed (i.e. shifted
by a non-zero offset) by a syscall from userspace. The syscalls than can
(at the time of writing) trigger such record are:
- settimeofday(2), stime(2), clock_settime(2) -- via
do_settimeofday64()
- adjtimex(2), clock_adjtime(2) -- via do_adjtimex()
The new records have type AUDIT_TIME_INJOFFSET and contain the following
fields:
- sec -- the 'seconds' part of the offset
- nsec -- the 'nanoseconds' part of the offset
Example record (time was shifted backwards by ~15.875 seconds):
type=TIME_INJOFFSET msg=audit(1530616049.652:13): sec=-16 nsec=124887145
The records of this type will be associated with the corresponding
syscall records.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[PM: fixed a line width problem in __audit_tk_injoffset()]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current API for the wilco EC mailbox interface is bad.
It assumes that most messages sent to the EC follow a similar structure,
with a command byte in MBOX[0], followed by a junk byte, followed by
actual data. This doesn't happen in several cases, such as setting the
RTC time, using the raw debugfs interface, and reading or writing
properties such as the Peak Shift policy (this last to be submitted soon).
Similarly for the response message from the EC, the current interface
assumes that the first byte of data is always 0, and the second byte
is unused. However, in both setting and getting the RTC time, in the
debugfs interface, and for reading and writing properties, this isn't
true.
The current way to resolve this is to use WILCO_EC_FLAG_RAW* flags to
specify when and when not to skip these initial bytes in the sent and
received message. They are confusing and used so much that they are
normal, and not exceptions. In addition, the first byte of
response in the debugfs interface is still always skipped, which is
weird, since this raw interface should be giving the entire result.
Additionally, sent messages assume the first byte is a command, and so
struct wilco_ec_message contains the "command" field. In setting or
getting properties however, the first byte is not a command, and so this
field has to be filled with a byte that isn't actually a command. This
is again inconsistent.
wilco_ec_message contains a result field as well, copied from
wilco_ec_response->result. The message result field should be removed:
if the message fails, the cause is already logged, and the callers are
alerted. They will never care about the actual state of the result flag.
These flags and different cases make the wilco_ec_transfer() function,
used in wilco_ec_mailbox(), really gross, dealing with a bunch of
different cases. It's difficult to figure out what it is doing.
Finally, making these assumptions about the structure of a message make
it so that the messages do not correspond well with the specification
for the EC's mailbox interface. For instance, this interface
specification may say that MBOX[9] in the received message contains
some information, but the calling code needs to remember that the first
byte of response is always skipped, and because it didn't set the
RESPONSE_RAW flag, the next byte is also skipped, so this information
is actually contained within wilco_ec_message->response_data[7]. This
makes it difficult to maintain this code in the future.
To fix these problems this patch standardizes the mailbox interface by:
- Removing the WILCO_EC_FLAG_RAW* flags
- Removing the command and reserved_raw bytes from wilco_ec_request
- Removing the mbox0 byte from wilco_ec_response
- Simplifying wilco_ec_transfer() because of these changes
- Gives the callers of wilco_ec_mailbox() the responsibility of exactly
and consistently defining the structure of the mailbox request and
response
- Removing command and result from wilco_ec_message.
This results in the reduction of total code, and makes it much more
maintainable and understandable.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.
Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.
Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.
Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().
[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
Controller Databook version 4.90a
[2] http://www.ti.com/lit/ug/spruid7c/spruid7c.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
In commit b1fca27d384e ("kernel debug: support resetting WARN*_ONCE")
we got the opportunity to reset state on the one shot messages,
without having to reboot.
However printk_once (printk_deferred_once) live in a different file
and didn't get the same kind of update/conversion, so they remain
unconditionally one shot, until the system is rebooted.
For example, we currently have:
sched/rt.c: printk_deferred_once("sched: RT throttling activated\n");
..which could reasonably be tripped as someone is testing and tuning
a new system/workload and their task placements. For consistency, and
to avoid reboots in the same vein as the original commit, we make these
two instances of _once the same as the WARN*_ONCE instances are.
Link: http://lkml.kernel.org/r/1555121491-31213-1-git-send-email-paul.gortmaker@windriver.com
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
This Patch Adds fpga API's to support the Bitstream loading
by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Need rc5 for udl fix to add udl cleanups on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Merge page ref overflow branch.
Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).
Admittedly it's not exactly easy. To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers. Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).
Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication. So let's just do that.
* branch page-refs:
fs: prevent page refcount overflow in pipe_buf_get
mm: prevent get_user_pages() from overflowing page refcount
mm: add 'try_get_page()' helper function
mm: make page ref count overflow check tighter and more explicit
|
|
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe". It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).
Also like 'get_page()', you can't use this function unless you already
had a reference to the page. The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.
The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.
NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.
That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).
Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Extend the inkern API with a function for reading available
attribute values of iio channels.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A previous commit moved the shallow depth and BFQ depth map calculations
to be done at init time, moving it outside of the hotter IO path. This
potentially causes hangs if the users changes the depth of the scheduler
map, by writing to the 'nr_requests' sysfs file for that device.
Add a blk-mq-sched hook that allows blk-mq to inform the scheduler if
the depth changes, so that the scheduler can update its internal state.
Tested-by: Kai Krakow <kai@kaishome.de>
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Fixes: f0635b8a416e ("bfq: calculate shallow depths at init time")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block fixes from Jens Axboe:
"Set of fixes that should go into this round. This pull is larger than
I'd like at this time, but there's really no specific reason for that.
Some are fixes for issues that went into this merge window, others are
not. Anyway, this contains:
- Hardware queue limiting for virtio-blk/scsi (Dongli)
- Multi-page bvec fixes for lightnvm pblk
- Multi-bio dio error fix (Jason)
- Remove the cache hint from the io_uring tool side, since we didn't
move forward with that (me)
- Make io_uring SETUP_SQPOLL root restricted (me)
- Fix leak of page in error handling for pc requests (Jérôme)
- Fix BFQ regression introduced in this merge window (Paolo)
- Fix break logic for bio segment iteration (Ming)
- Fix NVMe cancel request error handling (Ming)
- NVMe pull request with two fixes (Christoph):
- fix the initial CSN for nvme-fc (James)
- handle log page offsets properly in the target (Keith)"
* tag 'for-linus-20190412' of git://git.kernel.dk/linux-block:
block: fix the return errno for direct IO
nvmet: fix discover log page when offsets are used
nvme-fc: correct csn initialization and increments on error
block: do not leak memory in bio_copy_user_iov()
lightnvm: pblk: fix crash in pblk_end_partial_read due to multipage bvecs
nvme: cancel request synchronously
blk-mq: introduce blk_mq_complete_request_sync()
scsi: virtio_scsi: limit number of hw queues by nr_cpu_ids
virtio-blk: limit number of hw queues by nr_cpu_ids
block, bfq: fix use after free in bfq_bfqq_expire
io_uring: restrict IORING_SETUP_SQPOLL to root
tools/io_uring: remove IOCQE_FLAG_CACHEHIT
block: don't use for-inside-for in bio_for_each_segment_all
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fix:
- Fix a deadlock in close() due to incorrect draining of RDMA queues
Bugfixes:
- Revert "SUNRPC: Micro-optimise when the task is known not to be
sleeping" as it is causing stack overflows
- Fix a regression where NFSv4 getacl and fs_locations stopped
working
- Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
- Fix xfstests failures due to incorrect copy_file_range() return
values"
* tag 'nfs-for-5.1-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
Revert "SUNRPC: Micro-optimise when the task is known not to be sleeping"
NFSv4.1 fix incorrect return value in copy_file_range
xprtrdma: Fix helper that drains the transport
NFS: Fix handling of reply page vector
NFS: Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's more than a handful of clk driver fixes for changes that came
in during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Fix PLL_1416X not rounding rates
clk: mediatek: fix clk-gate flag setting
platform/x86: pmc_atom: Drop __initconst on dmi table
clk: x86: Add system specific quirk to mark clocks as critical
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
clk: at91: fix programmable clock for sama5d2
|
|
"__u32" and similar types are intended for things exported to user-space,
including structs used in ioctls; see include/uapi/asm-generic/int-l64.h.
They are not needed for the CPER struct definitions, which not exported to
user-space and not used in ioctls. Replace them with the typical "u32" and
similar types. No functional change intended.
The reason for changing this is to remove the question of "why do we use
__u32 here instead of u32?" We should use __u32 when there's a reason for
it; otherwise, we should prefer u32 for consistency.
Reference: Documentation/process/coding-style.rst
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Andrew Morton <akpm@linux-foundation.org>
|
|
Add UEFI spec references for CPER UUIDs and structures, fix a few typos,
and remove some useless comments. No functional change intended.
Link: http://www.uefi.org/specifications
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Ingo Molnar:
"Fix an objtool warning plus fix a u64_to_user_ptr() macro expansion
bug"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Add rewind_stack_do_exit() to the noreturn list
linux/kernel.h: Use parentheses around argument in u64_to_user_ptr()
|
|
commit d7065da03822 ("get rid of the magic around f_count in aio") added
fput_atomic to include/linux/fs.h, motivated by its use in __aio_put_req()
in fs/aio.c.
Later, commit 3ffa3c0e3f6e ("aio: now fput() is OK from interrupt context;
get rid of manual delayed __fput()") removed the only use of fput_atomic
in __aio_put_req(), but did not remove the since then unused fput_atomic
definition in include/linux/fs.h.
We curate this now and finally remove the unused definition.
This issue was identified during a code review due to a coccinelle warning
from the atomic_as_refcounter.cocci rule pointing to the use of atomic_t
in fput_atomic.
Suggested-by: Krystian Radlak <kradlak@exida.com>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
As reported by Guenter Roeck, the new bit-locking using
BIT(1) doesn't work on the m68k architecture. m68k only requires
2-byte alignment for words and longwords, so there is only one
unused bit in pointers to structs - We current use two, one for the
NULLS marker at the end of the linked list, and one for the bit-lock
in the head of the list.
The two uses don't need to conflict as we never need the head of the
list to be a NULLS marker - the marker is only needed to check if an
object has moved to a different table, and the bucket head cannot
move. The NULLS marker is only needed in a ->next pointer.
As we already have different types for the bucket head pointer (struct
rhash_lock_head) and the ->next pointers (struct rhash_head), it is
fairly easy to treat the lsb differently in each.
So: Initialize buckets heads to NULL, and use the lsb for locking.
When loading the pointer from the bucket head, if it is NULL (ignoring
the lock big), report as being the expected NULLS marker.
When storing a value into a bucket head, if it is a NULLS marker,
store NULL instead.
And convert all places that used bit 1 for locking, to use bit 0.
Fixes: 8f0db018006a ("rhashtable: use bit_spin_locks to protect hash bucket.")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only times rht_ptr_locked() is used, it is to store a new
value in a bucket-head. This is the only time it makes sense
to use it too. So replace it by a function which does the
whole task: Sets the lock bit and assigns to a bucket head.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than dereferencing a pointer to a bucket and then passing the
result to rht_ptr(), we now pass in the pointer and do the dereference
in rht_ptr().
This requires that we pass in the tbl and hash as well to support RCU
checks, and means that the various rht_for_each functions can expect a
pointer that can be dereferenced without further care.
There are two places where we dereference a bucket pointer
where there is no testable protection - in each case we know
that we much have exclusive access without having taken a lock.
The previous code used rht_dereference() to pretend that holding
the mutex provided protects, but holding the mutex never provides
protection for accessing buckets.
So instead introduce rht_ptr_exclusive() that can be used when
there is known to be exclusive access without holding any locks.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch only moves some code around, it doesn't
change the code at all.
A subsequent patch will benefit from this as it needs
to add calls to functions which are now defined before the
call-site, but weren't before.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With these annotations, the rhashtable now gets no
warnings when compiled with "C=1" for sparse checking.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity into next-integrity
From Mimi:
"This pull request contains just three patches, the remainder are
either included in other pull requests (eg. audit, lockdown) or will
be upstreamed via other subsystems (eg. kselftests, Power). Included
in this pull request is one bug fix, one documentation update, and
extending the x86 IMA arch policy rules to coordinate the different
kernel module signature verification methods."
|
|
Add bpf_strtol and bpf_strtoul to convert a string to long and unsigned
long correspondingly. It's similar to user space strtol(3) and
strtoul(3) with a few changes to the API:
* instead of NUL-terminated C string the helpers expect buffer and
buffer length;
* resulting long or unsigned long is returned in a separate
result-argument;
* return value is used to indicate success or failure, on success number
of consumed bytes is returned that can be used to identify position to
read next if the buffer is expected to contain multiple integers;
* instead of *base* argument, *flags* is used that provides base in 5
LSB, other bits are reserved for future use;
* number of supported bases is limited.
Documentation for the new helpers is provided in bpf.h UAPI.
The helpers are made available to BPF_PROG_TYPE_CGROUP_SYSCTL programs to
be able to convert string input to e.g. "ulongvec" output.
E.g. "net/ipv4/tcp_mem" consists of three ulong integers. They can be
parsed by calling to bpf_strtoul three times.
Implementation notes:
Implementation includes "../../lib/kstrtox.h" to reuse integer parsing
functions. It's done exactly same way as fs/proc/base.c already does.
Unfortunately existing kstrtoX function can't be used directly since
they fail if any invalid character is present right after integer in the
string. Existing simple_strtoX functions can't be used either since
they're obsolete and don't handle overflow properly.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently the way to pass result from BPF helper to BPF program is to
provide memory area defined by pointer and size: func(void *, size_t).
It works great for generic use-case, but for simple types, such as int,
it's overkill and consumes two arguments when it could use just one.
Introduce new argument types ARG_PTR_TO_INT and ARG_PTR_TO_LONG to be
able to pass result from helper to program via pointer to int and long
correspondingly: func(int *) or func(long *).
New argument types are similar to ARG_PTR_TO_MEM with the following
differences:
* they don't require corresponding ARG_CONST_SIZE argument, predefined
access sizes are used instead (32bit for int, 64bit for long);
* it's possible to use more than one such an argument in a helper;
* provided pointers have to be aligned.
It's easy to introduce similar ARG_PTR_TO_CHAR and ARG_PTR_TO_SHORT
argument types. It's not done due to lack of use-case though.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add file_pos field to bpf_sysctl context to read and write sysctl file
position at which sysctl is being accessed (read or written).
The field can be used to e.g. override whole sysctl value on write to
sysctl even when sys_write is called by user space with file_pos > 0. Or
BPF program may reject such accesses.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
