| Age | Commit message (Collapse) | Author |
|---|
|
The upcoming SDCA (SoundWire Device Class Audio) specification defines
a hierarchical encoding to interface with Class-defined capabilities.
The specification is not yet accessible to the general public but this
information is released with explicit permission from the MIPI Board
to avoid delays with SDCA support on Linux platforms.
A block of 64 MBytes of register addresses are allocated to SDCA
controls, starting at address 0x40000000. The 26 LSBs which identify
individual controls are set based on the following variables:
- Function Number. An SCDA device can be split in up to 8 independent
Functions. Each of these Functions is described in the SDCA
specification, e.g. Smart Amplifier, Smart Microphone, Simple
Microphone, Jack codec, HID, etc.
- Entity Number. Within each Function, an Entity is an identifiable
block. Up to 127 Entities are connected in a pre-defined
graph (similar to USB), with Entity0 reserved for Function-level
configurations. In contrast to USB, the SDCA spec pre-defines
Function Types, topologies, and allowed options, i.e. the degree of
freedom is not unlimited to limit the possibility of errors in
descriptors leading to software quirks.
- Control Selector. Within each Entity, the SDCA specification defines
48 controls such as Mute, Gain, AGC, etc, and 16 implementation
defined ones. Some Control Selectors might be used for low-level
platform setup, and other exposed to applications and users. Note
that the same Control Selector capability, e.g. Latency control,
might be located at different offsets in different entities, the
Control Selector mapping is Entity-specific.
- Control Number. Some Control Selectors allow channel-specific values
to be set, with up to 64 channels allowed. This is mostly used for
volume control.
- Current/Next values. Some Control Selectors are
'Dual-Ranked'. Software may either update the Current value directly
for immediate effect. Alternatively, software may write into the
'Next' values and update the SoundWire 1.2 'Commit Groups' register
to copy 'Next' values into 'Current' ones in a synchronized
manner. This is different from bank switching which is typically
used to change the bus configuration only.
- MBQ. the Multi-Byte Quantity bit is used to provide atomic updates
when accessing more that one byte, for example a 16-bit volume
control would be updated consistently, the intermediate values
mixing old MSB with new LSB are not applied.
These 6 parameters are used to build a 32-bit address to access the
desired Controls. Because of address range, paging is required, but
the most often used parameter values are placed in the lower 16 bits
of the address. This helps to keep the paging registers constant while
updating Controls for a specific Device/Function.
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201103172226.4278-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TD.4.7.3. Try SNK DRP Connect Try.SRC DRP fails. The compliance
tester mimics being a Try.SRC USB-C port.
The failure is due to TCPM exiting SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS
when VBUS is not present eventhough when SNK.Rp is seen. Exit to
SRC_TRYWAIT from SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS only when SNK.Rp
is not seen for PD_T_TRY_CC_DEBOUNCE.
>From the spec:
The port shall then transition to Attached.SNK when the SNK.Rp state
is detected on exactly one of the CC1 or CC2 pins for at least
tTryCCDebounce and VBUS is detected. Alternatively, the port shall
transition to TryWait.SRC if SNK.Rp state is not detected for
tTryCCDebounce.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125014804.1596719-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Further perf/core patches will depend on:
d3f7b1bb2040 ("mm/gup: fix gup_fast with dynamic page table folding")
which is already in Linus' tree.
|
|
gpr_get() does membuf_write() twice to override pt_regs->msr in
between. We can call membuf_write() once and change ->msr in the
kernel buffer, this simplifies the code and the next fix.
The patch adds a new simple helper, membuf_at(offs), it returns the
new membuf which can be safely used after membuf_write().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[mpe: Fixup some minor whitespace issues noticed by Christophe]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201119160221.GA5188@redhat.com
|
|
USB Power Delivery Specification R3.0 introduced separate
field for the DFP product type to the ID Header VDO.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201125120642.37156-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A new API, rproc_set_firmware() is added to allow the remoteproc platform
drivers and remoteproc client drivers to be able to configure a custom
firmware name that is different from the default name used during
remoteproc registration. This function is being introduced to provide
a kernel-level equivalent of the current sysfs interface to remoteproc
client drivers, and can only change firmwares when the remoteproc is
offline. This allows some remoteproc drivers to choose different firmwares
at runtime based on the functionality the remote processor is providing.
The TI PRU Ethernet driver will be an example of such usage as it
requires to use different firmwares for different supported protocols.
Also, update the firmware_store() function used by the sysfs interface
to reuse this function to avoid code duplication.
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201121032042.6195-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The current semantic for napi_consume_skb() is that caller need
to provide non-zero budget when calling from NAPI context, and
breaking this semantic will cause hard to debug problem, because
_kfree_skb_defer() need to run in atomic context in order to push
the skb to the particular cpu' napi_alloc_cache atomically.
So add the lockdep_assert_in_softirq() to assert when the running
context is not in_softirq, in_softirq means softirq is serving or
BH is disabled, which has a ambiguous semantics due to the BH
disabled confusion, so add a comment to emphasize that.
And the softirq context can be interrupted by hard IRQ or NMI
context, lockdep_assert_in_softirq() need to assert about hard
IRQ or NMI context too.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is in preparation to add a helper for BPF LSM programs to use
IMA hashes when attached to LSM hooks. There are LSM hooks like
inode_unlink which do not have a struct file * argument and cannot
use the existing ima_file_hash API.
An inode based API is, therefore, useful in LSM based detections like an
executable trying to delete itself which rely on the inode_unlink LSM
hook.
Moreover, the ima_file_hash function does nothing with the struct file
pointer apart from calling file_inode on it and converting it to an
inode.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Link: https://lore.kernel.org/bpf/20201124151210.1081188-2-kpsingh@chromium.org
|
|
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 4b1faf931650 ("block: Kill bio_pair_split()"), there's
no user of BIO_SPLIT_ENTRIES anymore.
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
With the recent feature added to enable perf events to use pseudo NMIs
as interrupts on platforms which support GICv3 or later, its now been
possible to enable hard lockup detector (or NMI watchdog) on arm64
platforms. So enable corresponding support.
One thing to note here is that normally lockup detector is initialized
just after the early initcalls but PMU on arm64 comes up much later as
device_initcall(). So we need to re-initialize lockup detection once
PMU has been initialized.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/1602060704-10921-1-git-send-email-sumit.garg@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Clean up the module-param macros by adding some indentation and using
the __aligned() macro to improve readability.
Link: https://lore.kernel.org/lkml/20201103175711.10731-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|
|
Specify type alignment for kernel parameters instead of sizeof(void *).
The alignment attribute is used to prevent gcc from increasing the
alignment of objects with static extent as an optimisation, something
which would mess up the __param array stride.
Using __alignof__(struct kernel_param) rather than sizeof(void *) is
preferred since it better indicates why it is there and doesn't break
should the type size or alignment change.
Note that on m68k the alignment of struct kernel_param is actually two
and that adding a 1- or 2-byte field to the 20-byte struct would cause a
breakage with the current 4-byte alignment.
Link: https://lore.kernel.org/lkml/20201103175711.10731-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|
|
Drop the redundant "unused" attributes from module-parameter structures
already marked "used".
Link: https://lore.kernel.org/lkml/20201103175711.10731-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|
|
Instead of using the array-of-pointers trick to avoid having gcc mess up
the built-in module-version array stride, specify type alignment when
declaring entries to prevent gcc from increasing alignment.
This is essentially an alternative (one-line) fix to the problem
addressed by commit b4bc842802db ("module: deal with alignment issues in
built-in module versions").
gcc can increase the alignment of larger objects with static extent as
an optimisation, but this can be suppressed by using the aligned
attribute when declaring variables.
Note that we have been relying on this behaviour for kernel parameters
for 16 years and it indeed hasn't changed since the introduction of the
aligned attribute in gcc-3.1.
Link: https://lore.kernel.org/lkml/20201103175711.10731-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|
|
Commit 98562ad8cb03 ("module: explicitly align module_version_attribute
structure") added an alignment attribute to the struct
module_version_attribute type in order to fix an alignment issue on m68k
where the structure is 2-byte aligned while MODULE_VERSION() forced the
__modver section entries to be 4-byte aligned (sizeof(void *)).
This was essentially an alternative fix to the problem addressed by
b4bc842802db ("module: deal with alignment issues in built-in module
versions") which used the array-of-pointer trick to prevent gcc from
increasing alignment of the version attribute entries. And with the
pointer indirection in place there's no need to increase the alignment
of the type.
Link: https://lore.kernel.org/lkml/20201103175711.10731-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|
|
Add a quirk IO_PGTABLE_QUIRK_ARM_OUTER_WBWA to override
the outer-cacheability attributes set in the TCR for a
non-coherent page table walker when using system cache.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/f818676b4a2a9ad1edb92721947d47db41ed6a7c.1606287059.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add a new iommu domain attribute DOMAIN_ATTR_IO_PGTABLE_CFG
for pagetable configuration which initially will be used to
set quirks like for system cache aka last level cache to be
used by client drivers like GPU to set right attributes for
caching the hardware pagetables into the system cache and
later can be extended to include other page table configuration
data.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/9190aa16f378fc0a7f8e57b2b9f60b033e7eeb4f.1606287059.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add a iommu_dma_free_cpu_cached_iovas function to allow drivers which
use the dma-iommu ops to free cached cpu iovas.
Signed-off-by: Tom Murphy <murphyt7@tcd.ie>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20201124082057.2614359-3-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Allow the iommu_unmap_fast to return newly freed page table pages and
pass the freelist to queue_iova in the dma-iommu ops path.
This is useful for iommu drivers (in this case the intel iommu driver)
which need to wait for the ioTLB to be flushed before newly
free/unmapped page table pages can be freed. This way we can still batch
ioTLB free operations and handle the freelists.
Signed-off-by: Tom Murphy <murphyt7@tcd.ie>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20201124082057.2614359-2-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
DP0 has reserved fields and the read-only SDCA_CASCADE bit. We should
not try to write values in these fields, so add a formal definition
for clearable interrupts to be used in DP0 interrupt handling.
DPN also has reserved fields so add definitions for clearable
interrupts as well.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201124013318.8963-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
A copy-pasta mistake tries to set SYSCALL_WORK flags instead of TIF
flags for !CONFIG_GENERIC_ENTRY. Also, add safeguards to catch this at
compilation time.
Fixes: 3136b93c3fb2 ("entry: Expose helpers to migrate TIF to SYSCALL_WORK flags")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/87a6v8qd9p.fsf_-_@collabora.com
|
|
In an encrypted directory, a regular dentry (one that doesn't have the
no-key name flag) can only be created if the directory's encryption key
is available.
Therefore the calls to fscrypt_require_key() in __fscrypt_prepare_link()
and __fscrypt_prepare_rename() are unnecessary, as these functions
already check that the dentries they're given aren't no-key names.
Remove these unnecessary calls to fscrypt_require_key().
Link: https://lore.kernel.org/r/20201118075609.120337-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
It's possible to create a duplicate filename in an encrypted directory
by creating a file concurrently with adding the encryption key.
Specifically, sys_open(O_CREAT) (or sys_mkdir(), sys_mknod(), or
sys_symlink()) can lookup the target filename while the directory's
encryption key hasn't been added yet, resulting in a negative no-key
dentry. The VFS then calls ->create() (or ->mkdir(), ->mknod(), or
->symlink()) because the dentry is negative. Normally, ->create() would
return -ENOKEY due to the directory's key being unavailable. However,
if the key was added between the dentry lookup and ->create(), then the
filesystem will go ahead and try to create the file.
If the target filename happens to already exist as a normal name (not a
no-key name), a duplicate filename may be added to the directory.
In order to fix this, we need to fix the filesystems to prevent
->create(), ->mkdir(), ->mknod(), and ->symlink() on no-key names.
(->rename() and ->link() need it too, but those are already handled
correctly by fscrypt_prepare_rename() and fscrypt_prepare_link().)
In preparation for this, add a helper function fscrypt_is_nokey_name()
that filesystems can use to do this check. Use this helper function for
the existing checks that fs/crypto/ does for rename and link.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201118075609.120337-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Commit 642e450b6b59 ("xsk: Do not discard packet when NETDEV_TX_BUSY")
addressed the problem that packets were discarded from the Tx AF_XDP
ring, when the driver returned NETDEV_TX_BUSY. Part of the fix was
bumping the skbuff reference count, so that the buffer would not be
freed by dev_direct_xmit(). A reference count larger than one means
that the skbuff is "shared", which is not the case.
If the "shared" skbuff is sent to the generic XDP receive path,
netif_receive_generic_xdp(), and pskb_expand_head() is entered the
BUG_ON(skb_shared(skb)) will trigger.
This patch adds a variant to dev_direct_xmit(), __dev_direct_xmit(),
where a user can select the skbuff free policy. This allows AF_XDP to
avoid bumping the reference count, but still keep the NETDEV_TX_BUSY
behavior.
Fixes: 642e450b6b59 ("xsk: Do not discard packet when NETDEV_TX_BUSY")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201123175600.146255-1-bjorn.topel@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Prelude to gssapi support
Here are some patches that do some reorganisation of the security class
handling in rxrpc to allow implementation of the RxGK security class that
will allow AF_RXRPC to use GSSAPI-negotiated tokens and better crypto. The
RxGK security class is not included in this patchset.
It does the following things:
(1) Add a keyrings patch to provide the original key description, as
provided to add_key(), to the payload preparser so that it can
interpret the content on that basis. Unfortunately, the rxrpc_s key
type wasn't written to interpret its payload as anything other than a
string of bytes comprising a key, but for RxGK, more information is
required as multiple Kerberos enctypes are supported.
(2) Remove the rxk5 security class key parsing. The rxk5 class never got
rolled out in OpenAFS and got replaced with rxgk.
(3) Support the creation of rxrpc keys with multiple tokens of different
types. If some types are not supported, the ENOPKG error is
suppressed if at least one other token's type is supported.
(4) Punt the handling of server keys (rxrpc_s type) to the appropriate
security class.
(5) Organise the security bits in the rxrpc_connection struct into a
union to make it easier to override for other classes.
(6) Move some bits from core code into rxkad that won't be appropriate to
rxgk.
* tag 'rxrpc-next-20201123' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
rxrpc: Ask the security class how much space to allow in a packet
rxrpc: rxkad: Don't use pskb_pull() to advance through the response packet
rxrpc: Organise connection security to use a union
rxrpc: Don't reserve security header in Tx DATA skbuff
rxrpc: Merge prime_packet_security into init_connection_security
rxrpc: Fix example key name in a comment
rxrpc: Ignore unknown tokens in key payload unless no known tokens
rxrpc: Make the parsing of xdr payloads more coherent
rxrpc: Allow security classes to give more info on server keys
rxrpc: Don't leak the service-side session key to userspace
rxrpc: Hand server key parsing off to the security class
rxrpc: Split the server key type (rxrpc_s) into its own file
rxrpc: Don't retain the server key in the connection
rxrpc: Support keys with multiple authentication tokens
rxrpc: List the held token types in the key description in /proc/keys
rxrpc: Remove the rxk5 security class as it's now defunct
keys: Provide the original description to the key preparser
====================
Link: https://lore.kernel.org/r/160616220405.830164.2239716599743995145.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some complex dmaengine controllers have capability to program the
peripheral device, so pass on the peripheral configuration as part of
dma_slave_config
Link: https://lore.kernel.org/r/20201109085450.24843-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Make the RPMSG name service announcement a stand alone driver so that it
can be reused by other subsystems. It is also the first step in making the
functionatlity transport independent, i.e that is not tied to virtIO.
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Co-developed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-developed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20201120214245.172963-9-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Make function rpmsg_register_device() and rpmsg_unregister_device()
functions public so that they can be used by other clients. While
doing so get rid of two obsolete function, i.e register_rpmsg_device()
and unregister_rpmsg_device(), to prevent confusion.
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201120214245.172963-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Move structure rpmsg_ns_msg to its own header file so that
it can be used by other entities.
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201120214245.172963-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Introduce __rpmsg{16|32|64} types along with byte order conversion
functions based on an rpmsg_device operation as a foundation to
make RPMSG modular and transport agnostic.
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201120214245.172963-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Trade one atomic op for a full memory barrier.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
|
Get rid of the __call_single_node union and cleanup the API a little
to avoid external code relying on the structure layout as much.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
|
Get rid of the __call_single_node union and clean up the API a little
to avoid external code relying on the structure layout as much.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
|
Currently array of fix length PM_API_MAX is used to cache
the pm_api version (valid or invalid). However ATF based
PM APIs values are much higher then PM_API_MAX.
So to include ATF based PM APIs also, use hash-table to
store the pm_api version status.
Signed-off-by: Amit Sunil Dhamne <amit.sunil.dhamne@xilinx.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Fixes: f3217d6f2f7a ("firmware: xilinx: fix out-of-bounds access")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1606197161-25976-1-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Similar to kmap local provide a iomap local variant which only disables
migration, but neither disables pagefaults nor preemption.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20201118204007.561220818@linutronix.de
|
|
Now that the kmap atomic index is stored in task struct provide a
preemptible variant. On context switch the maps of an outgoing task are
removed and the map of the incoming task are restored. That's obviously
slow, but highmem is slow anyway.
The kmap_local.*() functions can be invoked from both preemptible and
atomic context. kmap local sections disable migration to keep the resulting
virtual mapping address correct, but disable neither pagefaults nor
preemption.
A wholesale conversion of kmap_atomic to be fully preemptible is not
possible because some of the usage sites might rely on the preemption
disable for serialization or on the implicit pagefault disable. Needs to be
done on a case by case basis.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20201118204007.468533059@linutronix.de
|
|
Instead of storing the map per CPU provide and use per task storage. That
prepares for local kmaps which are preemptible.
The context switch code is preparatory and not yet in use because
kmap_atomic() runs with preemption disabled. Will be made usable in the
next step.
The context switch logic is safe even when an interrupt happens after
clearing or before restoring the kmaps. The kmap index in task struct is
not modified so any nesting kmap in an interrupt will use unused indices
and on return the counter is the same as before.
Also add an assert into the return to user space code. Going back to user
space with an active kmap local is a nono.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20201118204007.372935758@linutronix.de
|
|
Pull the migrate disable mechanics which is a prerequisite for preemptible
kmap_local().
|
|
Now that the scheduler can deal with migrate disable properly, there is no
real compelling reason to make it only available for RT.
There are quite some code pathes which needlessly disable preemption in
order to prevent migration and some constructs like kmap_atomic() enforce
it implicitly.
Making it available independent of RT allows to provide a preemptible
variant of kmap_atomic() and makes the code more consistent in general.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Grudgingly-Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20201118204007.269943012@linutronix.de
|
|
The SoundWire 1.2 specification defines an "SDCA cascade" bit which
handles a logical OR of all SDCA interrupt sources (up to 30 defined).
Due to limitations of the addressing space, this bit is located in the
SDW_DP0_INT register when DP0 is used, or alternatively in the
DP0_SDCA_Support_INTSTAT register when DP0 is not used.
To allow for both cases to be handled, this bit will be checked in the
main device-level interrupt handling code. This will result in the
register being read twice if DP0 is enabled, but it's not clear how to
optimize this case. It's also more logical to deal with this interrupt
at the device than the port level, this bit is really not DP0 specific
and its location in the DP0_INTSTAT bit is only due to the lack of
free space in SCP_INTSTAT_1.
The SDCA_Cascade bit cannot be masked or cleared, so the interrupt
handling only forwards the detection to the Slave driver, which will
deal with reading the relevant SDCA status bits and clearing them. The
bus driver only signals the detection.
The communication with the Slave driver is based on the same interrupt
callback, with only an extension to provide the status of the
sdca_cascade bit.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201104152358.9518-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.11 cycle
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
* tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings:iio:adc:x-powers,axp209-adc: txt to yaml conversion
dt-bindings:iio:adc:renesas,rcar-gyroadc: txt to yaml conversion.
dt-bindings:iio:adc:atmel,sama5d2-adc: txt to yaml conversion
dt-bindings:iio:magnetometer:pni,rm3100: txt to yaml conversion.
dt-bindings:iio:magnetometer:honeywell,hmc5843: txt to yaml format conversion
dt-bindings:iio:magnetometer:bosch,bmc150_magn: txt to yaml conversion.
dt-bindings:iio:magnetometer:asahi-kasei,ak8974: txt to yaml format conversion
dt-bindings:iio:magnetometer:fsl,mag3110: txt to yaml conversion
dt-bindings:iio:light:st,vl6180: txt to yaml format conversion.
dt-bindings:iio:light:vishay,vcnl4035: txt to yaml conversion
dt-bindings:iio:light:st,uvis25: txt to yaml conversion for this UV sensor
dt-bindings:iio:light:upisemi,us51882: txt to yaml conversion.
dt-bindings:iio:light:ti,opt3001: txt to yaml conversion
dt-bindings:iio:light:maxim,max44009: txt to yaml conversion.
dt-bindings:iio:light:sharp,gp2ap020a00f: txt to yaml conversion.
dt-bindings:iio:light:capella,cm36651: txt to yaml conversion.
dt-bindings:iio:light:avago,apds9960: txt to yaml conversion
dt-bindings:iio:light:avago,apds9300: txt to yaml conversion.
dt-bindings:iio:imu:st,lsm6dsx: txt to yaml conversion
dt-bindings:iio:imu:adi,adis16480: txt to yaml conversion
...
|
|
In the patchset merged by commit b9fcf0a0d826
("Merge branch 'support-AF_PACKET-for-layer-3-devices'") L3 devices which
did not have header_ops were given one for the purpose of protocol parsing
on af_packet transmit path.
That change made af_packet receive path regard these devices as having a
visible L3 header and therefore aligned incoming skb->data to point to the
skb's mac_header. Some devices, such as ipip, xfrmi, and others, do not
reset their mac_header prior to ingress and therefore their incoming
packets became malformed.
Ideally these devices would reset their mac headers, or af_packet would be
able to rely on dev->hard_header_len being 0 for such cases, but it seems
this is not the case.
Fix by changing af_packet RX ll visibility criteria to include the
existence of a '.create()' header operation, which is used when creating
a device hard header - via dev_hard_header() - by upper layers, and does
not exist in these L3 devices.
As this predicate may be useful in other situations, add it as a common
dev_has_header() helper in netdevice.h.
Fixes: b9fcf0a0d826 ("Merge branch 'support-AF_PACKET-for-layer-3-devices'")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20201121062817.3178900-1-eyal.birger@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As pointed out by Herbert in a recent related patch, the LSM hooks do
not have the necessary address family information to use the flowi
struct safely. As none of the LSMs currently use any of the protocol
specific flowi information, replace the flowi pointers with pointers
to the address family independent flowi_common struct.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Using PTP wide defines will obsolete different driver internal defines
and uses of magic numbers.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For dependencies in following patches
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung SoC drivers changes for v5.11
1. Limit the big.LITTLE cpuidle driver to Peach-Pit/Pi Chromebooks only
because these are the only platforms were the driver works properly.
2. Convert the Exynos CLKOUT driver to a full module which solves
boot-probe ordering issues (e.g. if device nodes in DTS are moved).
This also brings modularization and compile testing.
3. Few minor cleanups in documentation and code.
* tag 'samsung-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: allow building the clkout driver as module
soc: samsung: s3c-pm-check: Fix incorrectly named variable 'val'
soc: samsung: exynos5422-asv: remove unneeded semicolon
serial: s3c: Update path of Samsung S3C machine file
Documentation: Update paths of Samsung S3C machine files
clk: samsung: exynos-clkout: convert to module driver
soc: samsung: exynos-pmu: instantiate clkout driver as MFD
cpuidle: big.LITTLE: enable driver only on Peach-Pit/Pi Chromebooks
Link: https://lore.kernel.org/r/20201113162211.10020-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
During regulators registration, if .of_match and .regulators_node are
defined as non-null strings in struct regulator_desc the core searches the
DT subtree rooted at .regulators_node trying to match, at first, .of_match
against the 'regulator-compatible' property and, then, falling back to use
the name of the node itself to determine a good match.
Property 'regulator-compatible', though, is now deprecated and falling back
to match against the node name, works fine only as long as the involved
nodes are named in an unique way across the searched subtree; if that's not
the case, like when using <common-name>@<unit> style naming for properties
indexed via 'reg' property (as advised by the standard), the above matching
mechanism based on the simple common name will lead to multiple matches and
the only viable alternative would be to properly define the now deprecated
'regulator-compatible' as the node full name, i.e. <common-name>@<unit>.
In order to address this case without using such deprecated binding, define
a new boolean flag .of_match_full_name in struct regulator_desc to force
the core to match against the node full-name instead of the plain name.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20201119191051.46363-4-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
