| Age | Commit message (Collapse) | Author |
|---|
|
For the smartreflex device, we need to disable smartreflex on SoC idle,
and have been using pm_runtime_irq_safe() to do that. But we want to
remove the irq_safe usage as PM runtime takes a permanent usage count
on the parent device with it.
In order to remove the need for pm_runtime_irq_safe(), let's gate
the clock directly in the driver. This removes the need to call PM runtime
during idle, and allows us to switch to using CPU_PM in the following
patch.
Note that the smartreflex interconnect target module is configured for smart
idle, but the clock does not have autoidle capability, and needs to be gated
manually. If the clock supported autoidle, we would not need to even gate
the clock.
With this change, we can now remove the related quirk flags for ti-sysc
also.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into drm-next
Bus: Make remove callback return void tag
Tag for other trees/branches to pull from in order to have a stable
place to build off of if they want to add new busses for 5.15.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixed up merge conflict in drm]
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/YPkwQwf0dUKnGA7L@kroah.com
|
|
The Intel 82426EX ISA Bridge (IB), a part of the Intel 82420EX PCIset,
implements PCI interrupt steering with a PIRQ router in the form of two
PIRQ Route Control registers, available in the PCI configuration space
at locations 0x66 and 0x67 for the PIRQ0# and PIRQ1# lines respectively.
The semantics is the same as with the PIIX router, however it is not
clear if BIOSes use register indices or line numbers as the cookie to
identify PCI interrupts in their routing tables and therefore support
either scheme.
The IB is directly attached to the Intel 82425EX PCI System Controller
(PSC) component of the chipset via a dedicated PSC/IB Link interface
rather than the host bus or PCI. Therefore it does not itself appear in
the PCI configuration space even though it responds to configuration
cycles addressing registers it implements. Use 82425EX's identification
then for determining the presence of the IB.
References:
[1] "82420EX PCIset Data Sheet, 82425EX PCI System Controller (PSC) and
82426EX ISA Bridge (IB)", Intel Corporation, Order Number:
290488-004, December 1995, Section 3.3.18 "PIRQ1RC/PIRQ0RC--PIRQ
Route Control Registers", p. 61
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107200213490.9461@angie.orcam.me.uk
|
|
The ALi M1487 ISA Bus Controller (IBC), a part of the ALi FinALi 486
chipset, implements PCI interrupt steering with a PIRQ router[1] in the
form of four 4-bit mappings, spread across two PCI INTx Routing Table
Mapping Registers, available in the port I/O space accessible indirectly
via the index/data register pair at 0x22/0x23, located at indices 0x42
and 0x43 for the INT1/INT2 and INT3/INT4 lines respectively.
Additionally there is a separate PCI INTx Sensitivity Register at index
0x44 in the same port I/O space, whose bits 3:0 select the trigger mode
for INT[4:1] lines respectively[2]. Manufacturer's documentation says
that this register has to be set consistently with the relevant ELCR
register[3]. Add a router-specific hook then and use it to handle this
register.
Accesses to the port I/O space concerned here need to be unlocked by
writing the value of 0xc5 to the Lock Register at index 0x03
beforehand[4]. Do so then and then lock access after use for safety.
The IBC is implemented as a peer bridge on the host bus rather than a
southbridge on PCI and therefore it does not itself appear in the PCI
configuration space. It is complemented by the M1489 Cache-Memory PCI
Controller (CMP) host-to-PCI bridge, so use that device's identification
for determining the presence of the IBC.
References:
[1] "M1489/M1487: 486 PCI Chip Set", Version 1.2, Acer Laboratories
Inc., July 1997, Section 4: "Configuration Registers", pp. 76-77
[2] same, p. 77
[3] same, Section 5: "M1489/M1487 Software Programming Guide", pp.
99-100
[4] same, Section 4: "Configuration Registers", p. 37
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107191702020.9461@angie.orcam.me.uk
|
|
With CONFIG_IRQ_FORCED_THREADING=y, testing the boolean force_irqthreads
could incur a cache line miss in invoke_softirq() and other places.
Replace the test with a static key to avoid the potential cache miss.
[ tglx: Dropped the IDE part, removed the export and updated blk-mq ]
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tanner Love <tannerlove@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210602180338.3324213-1-tannerlove.kernel@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
pull-request: mlx5-next 2020-08-9
This pulls mlx5-next branch which includes patches already reviewed on
net-next and rdma mailing lists.
1) mlx5 single E-Switch FDB for lag
2) IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
3) Add DCS caps & fields support
[1] https://patchwork.kernel.org/project/netdevbpf/cover/20210803231959.26513-1-saeed@kernel.org/
[2] https://patchwork.kernel.org/project/netdevbpf/patch/0e3364dab7e0e4eea5423878b01aa42470be8d36.1626609184.git.leonro@nvidia.com/
[3] https://patchwork.kernel.org/project/netdevbpf/patch/55e1d69bef1fbfa5cf195c0bfcbe35c8019de35e.1624258894.git.leonro@nvidia.com/
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Lag, Create shared FDB when in switchdev mode
net/mlx5: E-Switch, add logic to enable shared FDB
net/mlx5: Lag, move lag destruction to a workqueue
net/mlx5: Lag, properly lock eswitch if needed
net/mlx5: Add send to vport rules on paired device
net/mlx5: E-Switch, Add event callback for representors
net/mlx5e: Use shared mappings for restoring from metadata
net/mlx5e: Add an option to create a shared mapping
net/mlx5: E-Switch, set flow source for send to uplink rule
RDMA/mlx5: Add shared FDB support
{net, RDMA}/mlx5: Extend send to vport rules
RDMA/mlx5: Fill port info based on the relevant eswitch
net/mlx5: Lag, add initial logic for shared FDB
net/mlx5: Return mdev from eswitch
IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
net/mlx5: Add DCS caps & fields support
====================
Link: https://lore.kernel.org/r/20210809202522.316930-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that there is an alternate method for returning an auth_stat
value, replace the RQ_AUTHERR flag with use of that new method.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
I'd like to take commit 4532608d71c8 ("SUNRPC: Clean up generic
dispatcher code") even further by using only private local SVC
dispatchers for all kernel RPC services. This change would enable
the removal of the logic that switches between
svc_generic_dispatch() and a service's private dispatcher, and
simplify the invocation of the service's pc_release method
so that humans can visually verify that it is always invoked
properly.
All that will come later.
First, let's provide a better way to return authentication errors
from SVC dispatcher functions. Instead of overloading the dispatch
method's *statp argument, add a field to struct svc_rqst that can
hold an error value.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
'nolibc.2021.07.20c', 'tasks.2021.07.20c', 'torture.2021.07.27a' and 'torturescript.2021.07.27a' into HEAD
doc.2021.07.20c: Documentation updates.
fixes.2021.08.06a: Miscellaneous fixes.
nocb.2021.07.20c: Callback-offloading (NOCB CPU) updates.
nolibc.2021.07.20c: Tiny userspace library updates.
tasks.2021.07.20c: Tasks RCU updates.
torture.2021.07.27a: In-kernel torture-test updates.
torturescript.2021.07.27a: Torture-test scripting updates.
|
|
For device mapper targets to take advantage of IMA's measurement
capabilities, the status functions for the individual targets need to be
updated to handle the status_type_t case for value STATUSTYPE_IMA.
Update status functions for the following target types, to log their
respective attributes to be measured using IMA.
01. cache
02. crypt
03. integrity
04. linear
05. mirror
06. multipath
07. raid
08. snapshot
09. striped
10. verity
For rest of the targets, handle the STATUSTYPE_IMA case by setting the
measurement buffer to NULL.
For IMA to measure the data on a given system, the IMA policy on the
system needs to be updated to have the following line, and the system
needs to be restarted for the measurements to take effect.
/etc/ima/ima-policy
measure func=CRITICAL_DATA label=device-mapper template=ima-buf
The measurements will be reflected in the IMA logs, which are located at:
/sys/kernel/security/integrity/ima/ascii_runtime_measurements
/sys/kernel/security/integrity/ima/binary_runtime_measurements
These IMA logs can later be consumed by various attestation clients
running on the system, and send them to external services for attesting
the system.
The DM target data measured by IMA subsystem can alternatively
be queried from userspace by setting DM_IMA_MEASUREMENT_FLAG with
DM_TABLE_STATUS_CMD.
Signed-off-by: Tushar Sugandhi <tusharsu@linux.microsoft.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
DM configures a block device with various target specific attributes
passed to it as a table. DM loads the table, and calls each target’s
respective constructors with the attributes as input parameters.
Some of these attributes are critical to ensure the device meets
certain security bar. Thus, IMA should measure these attributes, to
ensure they are not tampered with, during the lifetime of the device.
So that the external services can have high confidence in the
configuration of the block-devices on a given system.
Some devices may have large tables. And a given device may change its
state (table-load, suspend, resume, rename, remove, table-clear etc.)
many times. Measuring these attributes each time when the device
changes its state will significantly increase the size of the IMA logs.
Further, once configured, these attributes are not expected to change
unless a new table is loaded, or a device is removed and recreated.
Therefore the clear-text of the attributes should only be measured
during table load, and the hash of the active/inactive table should be
measured for the remaining device state changes.
Export IMA function ima_measure_critical_data() to allow measurement
of DM device parameters, as well as target specific attributes, during
table load. Compute the hash of the inactive table and store it for
measurements during future state change. If a load is called multiple
times, update the inactive table hash with the hash of the latest
populated table. So that the correct inactive table hash is measured
when the device transitions to different states like resume, remove,
rename, etc.
Signed-off-by: Tushar Sugandhi <tusharsu@linux.microsoft.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com> # leak fix
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
/s/reatdown/teardown/
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1621585689-177398-1-git-send-email-john.garry@huawei.com
|
|
Resuming timekeeping is a clock-was-set event and uses the clock-was-set
notification mechanism. This is in the way of making the clock-was-set
update for hrtimers selective so unnecessary IPIs are avoided when a CPU
base does not have timers queued which are affected by the clock setting.
Distangle it by invoking hrtimer_resume() on each unfreezing CPU and invoke
the new timerfd_resume() function from timekeeping_resume() which is the
only place where this is needed.
Rename hrtimer_resume() to hrtimer_resume_local() to reflect the change.
With this the clock_was_set*() functions are not longer required to IPI all
CPUs unconditionally and can get some smarts to avoid them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.488853478@linutronix.de
|
|
Resuming timekeeping is a clock-was-set event and uses the clock-was-set
notification mechanism. This is in the way of making the clock-was-set
update for hrtimers selective so unnecessary IPIs are avoided when a CPU
base does not have timers queued which are affected by the clock setting.
Provide a seperate timerfd_resume() interface so the resume logic and the
clock-was-set mechanism can be distangled in the core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.395287410@linutronix.de
|
|
If high resolution timers are disabled the timerfd notification about a
clock was set event is not happening for all cases which use
clock_was_set_delayed() because that's a NOP for HIGHRES=n, which is wrong.
Make clock_was_set_delayed() unconditially available to fix that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210713135158.196661266@linutronix.de
|
|
VQs may be accessed to mark the device broken while they are
created/destroyed. Hence protect the access to the vqs list.
Fixes: e2dcdfe95c0b ("virtio: virtio_break_device() to mark all virtqueues broken.")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-4-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
queueing
There are several scenarios that can result in posix_cpu_timer_set()
not queueing the timer but still leaving the threadgroup cputime counter
running or keeping the tick dependency around for a random amount of time.
1) If timer_settime() is called with a 0 expiration on a timer that is
already disabled, the process wide cputime counter will be started
and won't ever get a chance to be stopped by stop_process_timer()
since no timer is actually armed to be processed.
The following snippet is enough to trigger the issue.
void trigger_process_counter(void)
{
timer_t id;
struct itimerspec val = { };
timer_create(CLOCK_PROCESS_CPUTIME_ID, NULL, &id);
timer_settime(id, TIMER_ABSTIME, &val, NULL);
timer_delete(id);
}
2) If timer_settime() is called with a 0 expiration on a timer that is
already armed, the timer is dequeued but not really disarmed. So the
process wide cputime counter and the tick dependency may still remain
a while around.
The following code snippet keeps this overhead around for one week after
the timer deletion:
void trigger_process_counter(void)
{
timer_t id;
struct itimerspec val = { };
val.it_value.tv_sec = 604800;
timer_create(CLOCK_PROCESS_CPUTIME_ID, NULL, &id);
timer_settime(id, 0, &val, NULL);
timer_delete(id);
}
3) If the timer was initially deactivated, this call to timer_settime()
with an early expiration may have started the process wide cputime
counter even though the timer hasn't been queued and armed because it
has fired early and inline within posix_cpu_timer_set() itself. As a
result the process wide cputime counter may never stop until a new
timer is ever armed in the future.
The following code snippet can reproduce this:
void trigger_process_counter(void)
{
timer_t id;
struct itimerspec val = { };
signal(SIGALRM, SIG_IGN);
timer_create(CLOCK_PROCESS_CPUTIME_ID, NULL, &id);
val.it_value.tv_nsec = 1;
timer_settime(id, TIMER_ABSTIME, &val, NULL);
}
4) If the timer was initially armed with a former expiration value
before this call to timer_settime() and the current call sets an
early deadline that has already expired, the timer fires inline
within posix_cpu_timer_set(). In this case it must have been dequeued
before firing inline with its new expiration value, yet it hasn't
been disarmed in this case. So the process wide cputime counter and
the tick dependency may still be around for a while even after the
timer fired.
The following code snippet can reproduce this:
void trigger_process_counter(void)
{
timer_t id;
struct itimerspec val = { };
signal(SIGALRM, SIG_IGN);
timer_create(CLOCK_PROCESS_CPUTIME_ID, NULL, &id);
val.it_value.tv_sec = 100;
timer_settime(id, TIMER_ABSTIME, &val, NULL);
val.it_value.tv_sec = 0;
val.it_value.tv_nsec = 1;
timer_settime(id, TIMER_ABSTIME, &val, NULL);
}
Fix all these issues with triggering the related base next expiration
recalculation on the next tick. This also implies to re-evaluate the need
to keep around the process wide cputime counter and the tick dependency, in
a similar fashion to disarm_timer().
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-7-frederic@kernel.org
|
|
A timer deletion only dequeues the timer but it doesn't shutdown
the related costly process wide cputimer counter and the tick dependency.
The following code snippet keeps this overhead around for one week after
the timer deletion:
void trigger_process_counter(void)
{
timer_t id;
struct itimerspec val = { };
val.it_value.tv_sec = 604800;
timer_create(CLOCK_PROCESS_CPUTIME_ID, NULL, &id);
timer_settime(id, 0, &val, NULL);
timer_delete(id);
}
Make sure the next target's tick recalculates the nearest expiration and
clears the process wide counter and tick dependency if necessary.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-3-frederic@kernel.org
|
|
Starting the process wide cputime counter needs to be done in the same
sighand locking sequence than actually arming the related timer otherwise
this races against concurrent timers setting/expiring in the same
threadgroup.
Detecting that the cputime counter is started without holding the sighand
lock is a first step toward debugging such situations.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210726125513.271824-2-frederic@kernel.org
|
|
Daniel Borkmann says:
====================
bpf-next 2021-08-10
We've added 31 non-merge commits during the last 8 day(s) which contain
a total of 28 files changed, 3644 insertions(+), 519 deletions(-).
1) Native XDP support for bonding driver & related BPF selftests, from Jussi Maki.
2) Large batch of new BPF JIT tests for test_bpf.ko that came out as a result from
32-bit MIPS JIT development, from Johan Almbladh.
3) Rewrite of netcnt BPF selftest and merge into test_progs, from Stanislav Fomichev.
4) Fix XDP bpf_prog_test_run infra after net to net-next merge, from Andrii Nakryiko.
5) Follow-up fix in unix_bpf_update_proto() to enforce socket type, from Cong Wang.
6) Fix bpf-iter-tcp4 selftest to print the correct dest IP, from Jose Blanquicet.
7) Various misc BPF XDP sample improvements, from Niklas Söderlund, Matthew Cover,
and Muhammad Falak R Wani.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (31 commits)
bpf, tests: Add tail call test suite
bpf, tests: Add tests for BPF_CMPXCHG
bpf, tests: Add tests for atomic operations
bpf, tests: Add test for 32-bit context pointer argument passing
bpf, tests: Add branch conversion JIT test
bpf, tests: Add word-order tests for load/store of double words
bpf, tests: Add tests for ALU operations implemented with function calls
bpf, tests: Add more ALU64 BPF_MUL tests
bpf, tests: Add more BPF_LSH/RSH/ARSH tests for ALU64
bpf, tests: Add more ALU32 tests for BPF_LSH/RSH/ARSH
bpf, tests: Add more tests of ALU32 and ALU64 bitwise operations
bpf, tests: Fix typos in test case descriptions
bpf, tests: Add BPF_MOV tests for zero and sign extension
bpf, tests: Add BPF_JMP32 test cases
samples, bpf: Add an explict comment to handle nested vlan tagging.
selftests/bpf: Add tests for XDP bonding
selftests/bpf: Fix xdp_tx.c prog section name
net, core: Allow netdev_lower_get_next_private_rcu in bh context
bpf, devmap: Exclude XDP broadcast to master device
net, bonding: Add XDP support to the bonding driver
...
====================
Link: https://lore.kernel.org/r/20210810130038.16927-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
bpf 2021-08-10
We've added 5 non-merge commits during the last 2 day(s) which contain
a total of 7 files changed, 27 insertions(+), 15 deletions(-).
1) Fix missing bpf_read_lock_trace() context for BPF loader progs, from Yonghong Song.
2) Fix corner case where BPF prog retrieves wrong local storage, also from Yonghong Song.
3) Restrict availability of BPF write_user helper behind lockdown, from Daniel Borkmann.
4) Fix multiple kernel-doc warnings in BPF core, from Randy Dunlap.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, core: Fix kernel-doc notation
bpf: Fix potentially incorrect results with bpf_get_local_storage()
bpf: Add missing bpf_read_[un]lock_trace() for syscall program
bpf: Add lockdown check for probe_write_user helper
bpf: Add _kernel suffix to internal lockdown_bpf_read
====================
Link: https://lore.kernel.org/r/20210810144025.22814-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the !CONFIG_BLOCK build after the recent cleanup.
Fixes: 5ed964f8e54e ("mm: hide laptop_mode_wb_timer entirely behind the BDI API")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The new UAPI will have its own firewall, and we don't want to run
the firewall in the Host1x driver for those jobs. As such, add a
parameter to host1x_job_alloc to specify if we want to skip the
firewall in the Host1x driver.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for inserting syncpoint waits in the CDMA pushbuffer.
These waits need to be done in HOST1X class, while gather submitted
by the application execute in engine class.
Support is added by converting the gather list of job into a command
list that can include both gathers and waits. When the job is
submitted, these commands are pushed as the appropriate opcodes
on the CDMA pushbuffer.
Also supported are waits relative to the start of the job,
which are useful for jobs doing multiple things with an engine
that doesn't natively support pipelining.
While at it, use 32-bit waits on chips that support them.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a callback field to the job structure, to be called just before
the job is to be freed. This allows the job's submitter to clean
up any of its own state, like decrement runtime PM refcounts.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a new property for jobs to enable or disable recovery i.e.
CPU increments of syncpoints to max value on job timeout. This
allows for a more solid model for hanged jobs, where userspace
doesn't need to guess if a syncpoint increment happened because
the job completed, or because job timeout was triggered.
On job timeout, we stop the channel, NOP all future jobs on the
channel using the same syncpoint, mark the syncpoint as locked
and resume the channel from the next job, if any.
The future jobs are NOPed, since because we don't do the CPU
increments, the value of the syncpoint is no longer synchronized,
and any waiters would become confused if a future job incremented
the syncpoint. The syncpoint is marked locked to ensure that any
future jobs cannot increment the syncpoint either, until the
application has recognized the situation and reallocated the
syncpoint.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add an implementation of dma_fences based on syncpoints. Syncpoint
interrupts are used to signal fences. Additionally, after
software signaling has been enabled, a 30 second timeout is started.
If the syncpoint threshold is not reached within this period,
the fence is signalled with an -ETIMEDOUT error code. This is to
allow fences that would never reach their syncpoint threshold to
be cleaned up. The timeout can potentially be removed in the future
after job tracking code has been refactored.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Introduce a new flag FAN_REPORT_PIDFD for fanotify_init(2) which
allows userspace applications to control whether a pidfd information
record containing a pidfd is to be returned alongside the generic
event metadata for each event.
If FAN_REPORT_PIDFD is enabled for a notification group, an additional
struct fanotify_event_info_pidfd object type will be supplied
alongside the generic struct fanotify_event_metadata for a single
event. This functionality is analogous to that of FAN_REPORT_FID in
terms of how the event structure is supplied to a userspace
application. Usage of FAN_REPORT_PIDFD with
FAN_REPORT_FID/FAN_REPORT_DFID_NAME is permitted, and in this case a
struct fanotify_event_info_pidfd object will likely follow any struct
fanotify_event_info_fid object.
Currently, the usage of the FAN_REPORT_TID flag is not permitted along
with FAN_REPORT_PIDFD as the pidfd API currently only supports the
creation of pidfds for thread-group leaders. Additionally, usage of
the FAN_REPORT_PIDFD flag is limited to privileged processes only
i.e. event listeners that are running with the CAP_SYS_ADMIN
capability. Attempting to supply the FAN_REPORT_TID initialization
flags with FAN_REPORT_PIDFD or creating a notification group without
CAP_SYS_ADMIN will result with -EINVAL being returned to the caller.
In the event of a pidfd creation error, there are two types of error
values that can be reported back to the listener. There is
FAN_NOPIDFD, which will be reported in cases where the process
responsible for generating the event has terminated prior to the event
listener being able to read the event. Then there is FAN_EPIDFD, which
will be reported when a more generic pidfd creation error has occurred
when fanotify calls pidfd_create().
Link: https://lore.kernel.org/r/5f9e09cff7ed62bfaa51c1369e0f7ea5f16a91aa.1628398044.git.repnop@google.com
Signed-off-by: Matthew Bobrowski <repnop@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The copy_info_records_to_user() helper allows for the separation of
info record copying routines/conditionals from copy_event_to_user(),
which reduces the overall clutter within this function. This becomes
especially true as we start introducing additional info records in the
future i.e. struct fanotify_event_info_pidfd. On success, this helper
returns the total amount of bytes that have been copied into the user
supplied buffer and on error, a negative value is returned to the
caller.
The newly defined macro FANOTIFY_INFO_MODES can be used to obtain info
record types that have been enabled for a specific notification
group. This macro becomes useful in the subsequent patch when the
FAN_REPORT_PIDFD initialization flag is introduced.
Link: https://lore.kernel.org/r/8872947dfe12ce8ae6e9a7f2d49ea29bc8006af0.1628398044.git.repnop@google.com
Signed-off-by: Matthew Bobrowski <repnop@google.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
With the idea of returning pidfds from the fanotify API, we need to
expose a mechanism for creating pidfds. We drop the static qualifier
from pidfd_create() and add its declaration to linux/pid.h so that the
pidfd_create() helper can be called from other kernel subsystems
i.e. fanotify.
Link: https://lore.kernel.org/r/0c68653ec32f1b7143301f0231f7ed14062fd82b.1628398044.git.repnop@google.com
Signed-off-by: Matthew Bobrowski <repnop@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Fix a few typos in the documentation:
- Remove an extraneous 'or'
- 'unpins' -> 'unpin'
- 'braket' -> 'bracket'
- 'mappinsg' -> 'mappings'
- 'fullfills' -> 'fulfills'
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210809122247.15869-1-galpress@amazon.com
|
|
msi_desc::masked is a misnomer. For MSI it's used to cache the MSI mask
bits when the device supports per vector masking. For MSI-X it's used to
cache the content of the vector control word which contains the mask bit
for the vector.
Replace it with a union of msi_mask and msix_ctrl to make the purpose clear
and fix up the usage sites.
No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.045993608@linutronix.de
|
|
The PCI core already ensures that the MSI[-X] state is correct when MSI[-X]
is disabled. For MSI the reset state is all entries unmasked and for MSI-X
all vectors are masked.
S390 masks all MSI entries and masks the already masked MSI-X entries
again. Remove it and let the device in the correct state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20210729222542.939798136@linutronix.de
|
|
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de
|
|
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
|
|
Commit b910eaaaa4b8 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed a bug for bpf_get_local_storage() helper so different tasks
won't mess up with each other's percpu local storage.
The percpu data contains 8 slots so it can hold up to 8 contexts (same or
different tasks), for 8 different program runs, at the same time. This in
general is sufficient. But our internal testing showed the following warning
multiple times:
[...]
warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193
__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
<IRQ>
tcp_call_bpf.constprop.99+0x93/0xc0
tcp_conn_request+0x41e/0xa50
? tcp_rcv_state_process+0x203/0xe00
tcp_rcv_state_process+0x203/0xe00
? sk_filter_trim_cap+0xbc/0x210
? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160
tcp_v6_do_rcv+0x181/0x3e0
tcp_v6_rcv+0xc65/0xcb0
ip6_protocol_deliver_rcu+0xbd/0x450
ip6_input_finish+0x11/0x20
ip6_input+0xb5/0xc0
ip6_sublist_rcv_finish+0x37/0x50
ip6_sublist_rcv+0x1dc/0x270
ipv6_list_rcv+0x113/0x140
__netif_receive_skb_list_core+0x1a0/0x210
netif_receive_skb_list_internal+0x186/0x2a0
gro_normal_list.part.170+0x19/0x40
napi_complete_done+0x65/0x150
mlx5e_napi_poll+0x1ae/0x680
__napi_poll+0x25/0x120
net_rx_action+0x11e/0x280
__do_softirq+0xbb/0x271
irq_exit_rcu+0x97/0xa0
common_interrupt+0x7f/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac
? __cgroup_bpf_run_filter_skb+0x378/0x4e0
? do_softirq+0x34/0x70
? ip6_finish_output2+0x266/0x590
? ip6_finish_output+0x66/0xa0
? ip6_output+0x6c/0x130
? ip6_xmit+0x279/0x550
? ip6_dst_check+0x61/0xd0
[...]
Using drgn [0] to dump the percpu buffer contents showed that on this CPU
slot 0 is still available, but slots 1-7 are occupied and those tasks in
slots 1-7 mostly don't exist any more. So we might have issues in
bpf_cgroup_storage_unset().
Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset().
Currently, it tries to unset "current" slot with searching from the start.
So the following sequence is possible:
1. A task is running and claims slot 0
2. Running BPF program is done, and it checked slot 0 has the "task"
and ready to reset it to NULL (not yet).
3. An interrupt happens, another BPF program runs and it claims slot 1
with the *same* task.
4. The unset() in interrupt context releases slot 0 since it matches "task".
5. Interrupt is done, the task in process context reset slot 0.
At the end, slot 1 is not reset and the same process can continue to occupy
slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF
program won't be able to claim an empty slot and a warning will be issued.
To fix the issue, for unset() function, we should traverse from the last slot
to the first. This way, the above issue can be avoided.
The same reverse traversal should also be done in bpf_get_local_storage() helper
itself. Otherwise, incorrect local storage may be returned to BPF program.
[0] https://github.com/osandov/drgn
Fixes: b910eaaaa4b8 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210810010413.1976277-1-yhs@fb.com
|
|
Back then, commit 96ae52279594 ("bpf: Add bpf_probe_write_user BPF helper
to be called in tracers") added the bpf_probe_write_user() helper in order
to allow to override user space memory. Its original goal was to have a
facility to "debug, divert, and manipulate execution of semi-cooperative
processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed
since it would otherwise tamper with its integrity.
One use case was shown in cf9b1199de27 ("samples/bpf: Add test/example of
using bpf_probe_write_user bpf helper") where the program DNATs traffic
at the time of connect(2) syscall, meaning, it rewrites the arguments to
a syscall while they're still in userspace, and before the syscall has a
chance to copy the argument into kernel space. These days we have better
mechanisms in BPF for achieving the same (e.g. for load-balancers), but
without having to write to userspace memory.
Of course the bpf_probe_write_user() helper can also be used to abuse
many other things for both good or bad purpose. Outside of BPF, there is
a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and
PTRACE_POKE{TEXT,DATA}, but would likely require some more effort.
Commit 96ae52279594 explicitly dedicated the helper for experimentation
purpose only. Thus, move the helper's availability behind a newly added
LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under
the "integrity" mode. More fine-grained control can be implemented also
from LSM side with this change.
Fixes: 96ae52279594 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
|
|
The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.
This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.
As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ade359 ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
During log recovery of an XFS filesystem with 64kB directory
buffers, rebuilding a buffer split across two log records results
in a memory allocation warning from krealloc like this:
xfs filesystem being mounted at /mnt/scratch supports timestamps until 2038 (0x7fffffff)
XFS (dm-0): Unmounting Filesystem
XFS (dm-0): Mounting V5 Filesystem
XFS (dm-0): Starting recovery (logdev: internal)
------------[ cut here ]------------
WARNING: CPU: 5 PID: 3435170 at mm/page_alloc.c:3539 get_page_from_freelist+0xdee/0xe40
.....
RIP: 0010:get_page_from_freelist+0xdee/0xe40
Call Trace:
? complete+0x3f/0x50
__alloc_pages+0x16f/0x300
alloc_pages+0x87/0x110
kmalloc_order+0x2c/0x90
kmalloc_order_trace+0x1d/0x90
__kmalloc_track_caller+0x215/0x270
? xlog_recover_add_to_cont_trans+0x63/0x1f0
krealloc+0x54/0xb0
xlog_recover_add_to_cont_trans+0x63/0x1f0
xlog_recovery_process_trans+0xc1/0xd0
xlog_recover_process_ophdr+0x86/0x130
xlog_recover_process_data+0x9f/0x160
xlog_recover_process+0xa2/0x120
xlog_do_recovery_pass+0x40b/0x7d0
? __irq_work_queue_local+0x4f/0x60
? irq_work_queue+0x3a/0x50
xlog_do_log_recovery+0x70/0x150
xlog_do_recover+0x38/0x1d0
xlog_recover+0xd8/0x170
xfs_log_mount+0x181/0x300
xfs_mountfs+0x4a1/0x9b0
xfs_fs_fill_super+0x3c0/0x7b0
get_tree_bdev+0x171/0x270
? suffix_kstrtoint.constprop.0+0xf0/0xf0
xfs_fs_get_tree+0x15/0x20
vfs_get_tree+0x24/0xc0
path_mount+0x2f5/0xaf0
__x64_sys_mount+0x108/0x140
do_syscall_64+0x3a/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
Essentially, we are taking a multi-order allocation from kmem_alloc()
(which has an open coded no fail, no warn loop) and then
reallocating it out to 64kB using krealloc(__GFP_NOFAIL) and that is
then triggering the above warning.
This is a regression caused by converting this code from an open
coded no fail/no warn reallocation loop to using __GFP_NOFAIL.
What we actually need here is kvrealloc(), so that if contiguous
page allocation fails we fall back to vmalloc() and we don't
get nasty warnings happening in XFS.
Fixes: 771915c4f688 ("xfs: remove kmem_realloc()")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
|
|
For 32 bit systems with 64 bit dma, dma_addr[1] is used to
store the upper 32 bit dma addr, those system should be rare
those days.
For normal system, the dma_addr[1] in 'struct page' is not
used, so we can reuse dma_addr[1] for storing frag count,
which means how many frags this page might be splited to.
In order to simplify the page frag support in the page pool,
the PAGE_POOL_DMA_USE_PP_FRAG_COUNT macro is added to indicate
the 32 bit systems with 64 bit dma, and the page frag support
in page pool is disabled for such system.
The newly added page_pool_set_frag_count() is called to reserve
the maximum frag count before any page frag is passed to the
user. The page_pool_atomic_sub_frag_count_return() is called
when user is done with the page frag.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, page->pp is cleared and set everytime the page
is recycled, which is unnecessary.
So only set the page->pp when the page is added to the page
pool and only clear it when the page is released from the
page pool.
This is also a preparation to support allocating frag page
in page pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typo:
*assing ==> assign
*alloced ==> allocated
*Retun ==> Return
*excute ==> execute
v1->v2:
*reverse 'iff'
*update changelog
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This adds the ndo_xdp_get_xmit_slave hook for transforming XDP_TX
into XDP_REDIRECT after BPF program run when the ingress device
is a bond slave.
The dev_xdp_prog_count is exposed so that slave devices can be checked
for loaded XDP programs in order to avoid the situation where both
bond master and slave have programs loaded according to xdp_state.
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Link: https://lore.kernel.org/bpf/20210731055738.16820-3-joamaki@gmail.com
|
|
We really should not call rpc_wake_up_queued_task_set_status() with
xprt->snd_task as an argument unless we are certain that is actually an
rpc_task.
Fixes: 0445f92c5d53 ("SUNRPC: Fix disconnection races")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
There are now tools in the refcount library that allow us to convert the
client shutdown code.
Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Fixes: 2705dfb20947 ("block: fix discard request merge")
Link: https://lore.kernel.org/r/20210729034226.1591070-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rename LOCKDOWN_BPF_READ into LOCKDOWN_BPF_READ_KERNEL so we have naming
more consistent with a LOCKDOWN_BPF_WRITE_USER option that we are adding.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
|
|
The phrase "Counter Count function" is verbose and unintentionally
implies that function is a Count extension. This patch adjusts the
Counter subsystem code to use the more direct "Counter function" phrase
to make the intent of this code clearer.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: David Lechner <david@lechnology.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/8268c54d6f42075a19bb08151a37831e22652499.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signal values will always be levels so let's be explicit it about it to
make the intent of the code clear.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/3f17010abe2415859cea9a5fddabd3c97f635ff5.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Just retrieve the bdi from the disk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210809141744.1203023-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
