| Age | Commit message (Collapse) | Author |
|---|
|
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable reg c1 loopback if firmware reports it's supported,
as this is needed for restoring packet metadata (e.g chain).
Also define helper to query if it is enabled.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b72053072c0b ("block: allow partitions on host aware zone
devices") introduced the helper function disk_has_partitions() to check
if a given disk has valid partitions. However, since this function result
directly depends on the disk partition table length rather than the
actual existence of valid partitions in the table, it returns true even
after all partitions are removed from the disk. For host aware zoned
block devices, this results in zone management support to be kept
disabled even after removing all partitions.
Fix this by changing disk_has_partitions() to walk through the partition
table entries and return true if and only if a valid non-zero size
partition is found.
Fixes: b72053072c0b ("block: allow partitions on host aware zone devices")
Cc: stable@vger.kernel.org # 5.5
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This does three inter-related things to clarify the usage of the
platform device dma_mask field. In the process, fix the bug introduced
by cdfee5623290 ("driver core: initialize a default DMA mask for
platform device") that caused Artem Tashkinov's laptop to not boot with
newer Fedora kernels.
This does:
- First off, rename the field to "platform_dma_mask" to make it
greppable.
We have way too many different random fields called "dma_mask" in
various data structures, where some of them are actual masks, and
some of them are just pointers to the mask. And the structures all
have pointers to each other, or embed each other inside themselves,
and "pdev" sometimes means "platform device" and sometimes it means
"PCI device".
So to make it clear in the code when you actually use this new field,
give it a unique name (it really should be something even more unique
like "platform_device_dma_mask", since it's per platform device, not
per platform, but that gets old really fast, and this is unique
enough in context).
To further clarify when the field gets used, initialize it when we
actually start using it with the default value.
- Then, use this field instead of the random one-off allocation in
platform_device_register_full() that is now unnecessary since we now
already have a perfectly fine allocation for it in the platform
device structure.
- The above then allows us to fix the actual bug, where the error path
of platform_device_register_full() would unconditionally free the
platform device DMA allocation with 'kfree()'.
That kfree() was dont regardless of whether the allocation had been
done earlier with the (now removed) kmalloc, or whether
setup_pdev_dma_masks() had already been used and the dma_mask pointer
pointed to the mask that was part of the platform device.
It seems most people never triggered the error path, or only triggered
it from a call chain that set an explicit pdevinfo->dma_mask value (and
thus caused the unnecessary allocation that was "cleaned up" in the
error path) before calling platform_device_register_full().
Robin Murphy points out that in Artem's case the wdat_wdt driver failed
in platform_device_add(), and that was the one that had called
platform_device_register_full() with pdevinfo.dma_mask = 0, and would
have caused that kfree() of pdev.dma_mask corrupting the heap.
A later unrelated kmalloc() then oopsed due to the heap corruption.
Fixes: cdfee5623290 ("driver core: initialize a default DMA mask for platform device")
Reported-bisected-and-tested-by: Artem S. Tashkinov <aros@gmx.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add bpf_link_new_file() API for cases when we need to ensure anon_inode is
successfully created before we proceed with expensive BPF program attachment
procedure, which will require equally (if not more so) expensive and
potentially failing compensation detachment procedure just because anon_inode
creation failed. This API allows to simplify code by ensuring first that
anon_inode is created and after BPF program is attached proceed with
fd_install() that can't fail.
After anon_inode file is created, link can't be just kfree()'d anymore,
because its destruction will be performed by deferred file_operations->release
call. For this, bpf_link API required specifying two separate operations:
release() and dealloc(), former performing detachment only, while the latter
frees memory used by bpf_link itself. dealloc() needs to be specified, because
struct bpf_link is frequently embedded into link type-specific container
struct (e.g., struct bpf_raw_tp_link), so bpf_link itself doesn't know how to
properly free the memory. In case when anon_inode file was successfully
created, but subsequent BPF attachment failed, bpf_link needs to be marked as
"defunct", so that file's release() callback will perform only memory
deallocation, but no detachment.
Convert raw tracepoint and tracing attachment to new API and eliminate
detachment from error handling path.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309231051.1270337-1-andriin@fb.com
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- cgroup.procs listing related fixes.
It didn't interlock properly with exiting tasks leaving a short
window where a cgroup has empty cgroup.procs but still can't be
removed and misbehaved on short reads.
- psi_show() crash fix on 32bit ino archs
- Empty release_agent handling fix
* 'for-5.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup1: don't call release_agent when it is ""
cgroup: fix psi_show() crash on 32bit ino archs
cgroup: Iterate tasks that did not finish do_exit()
cgroup: cgroup_procs_next should increase position index
cgroup-v1: cgroup_pidlist_next should update position index
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Workqueue has been incorrectly round-robining per-cpu work items.
Hillf's patch fixes that.
The other patch documents memory-ordering properties of workqueue
operations"
* 'for-5.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: don't use wq_select_unbound_cpu() for bound works
workqueue: Document (some) memory-ordering properties of {queue,schedule}_work()
|
|
Similar to the commit 02d715b4a818 ("iommu/vt-d: Fix RCU list debugging
warnings"), there are several other places that call
list_for_each_entry_rcu() outside of an RCU read side critical section
but with dmar_global_lock held. Silence those false positives as well.
drivers/iommu/intel-iommu.c:4288 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffff935892c8 (dmar_global_lock){+.+.}, at: intel_iommu_init+0x1ad/0xb97
drivers/iommu/dmar.c:366 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffff935892c8 (dmar_global_lock){+.+.}, at: intel_iommu_init+0x125/0xb97
drivers/iommu/intel-iommu.c:5057 RCU-list traversed in non-reader section!!
1 lock held by swapper/0/1:
#0: ffffffffa71892c8 (dmar_global_lock){++++}, at: intel_iommu_init+0x61a/0xb13
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Synopsys DesignWare XPCS is an MMD that can manage link status,
auto-negotiation, link training, ...
In this commit we add basic support for XPCS using USXGMII interface and
Clause 73 Auto-negotiation.
This is highly tied with PHYLINK and can't be used without it. A given
ethernet driver can use the provided callbacks to add the support for
XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
This series adds some HW bits and definitions for mlx5 driver, to be
used by downstream features in both rdma and netdev branches.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: HW bit for goto chain offload support
net/mlx5: Expose link speed directly
net/mlx5: Introduce TLS and IPSec objects enums
net/mlx5: Introduce egress acl forward-to-vport capability
net/mlx5: Expose raw packet pacing APIs
net/mlx5e: Replace zero-length array with flexible-array member
net/mlx5: fix spelling mistake "reserverd" -> "reserved"
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The init, close and unhash handlers from TCP sockmap are generic,
and can be reused by UDP sockmap. Move the helpers into the sockmap code
base and expose them. This requires tcp_bpf_get_proto and tcp_bpf_clone to
be conditional on BPF_STREAM_PARSER.
The moved functions are unmodified, except that sk_psock_unlink is
renamed to sock_map_unlink to better match its behaviour.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-6-lmb@cloudflare.com
|
|
Only update psock->saved_* if psock->sk_proto has not been initialized
yet. This allows us to get rid of tcp_bpf_reinit_sk_prot.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-3-lmb@cloudflare.com
|
|
The sock map code checks that a socket does not have an active upper
layer protocol before inserting it into the map. This requires casting
via inet_csk, which isn't valid for UDP sockets.
Guard checks for ULP by checking inet_sk(sk)->is_icsk first.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-2-lmb@cloudflare.com
|
|
Set up a subdev in the q6v5 modem remoteproc driver that generates
event notifications for the IPA driver to use for initialization and
recovery following a modem shutdown or crash.
A pair of new functions provides a way for the IPA driver to register
and deregister a notification callback function that will be called
whenever modem events (about to boot, running, about to shut down,
etc.) occur. A void pointer value (provided by the IPA driver at
registration time) and an event type are supplied to the callback
function.
One event, MODEM_REMOVING, is signaled whenever the q6v5 driver is
about to remove the notification subdevice. It requires the IPA
driver de-register its callback.
This sub-device is only used by the modem subsystem (MSS) driver,
so the code that adds the new subdev and allows registration and
deregistration of the notifier is found in "qcom_q6v6_mss.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 1ec17dbd90f8 ("inet_diag: fix reporting cgroup classid and
fallback to priority") croup classid reporting was fixed. But this works
only for TCP sockets because for other socket types icsk parameter can
be NULL and classid code path is skipped. This change moves classid
handling to inet_diag_msg_attrs_fill() function.
Also inet_diag_msg_attrs_size() helper was added and addends in
nlmsg_new() were reordered to save order from inet_sk_diag_fill().
Fixes: 1ec17dbd90f8 ("inet_diag: fix reporting cgroup classid and fallback to priority")
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs fixes from Greg KH:
"Here are four small driver core / debugfs patches for 5.6-rc3:
- debugfs api cleanup now that all debugfs_create_regset32() callers
have been fixed up. This was waiting until after the -rc1 merge as
these fixes came in through different trees
- driver core sync state fixes based on reports of minor issues found
in the feature
All of these have been in linux-next with no reported issues"
* tag 'driver-core-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Skip unnecessary work when device doesn't have sync_state()
driver core: Add dev_has_sync_state()
driver core: Call sync_state() even if supplier has no consumers
debugfs: remove return value of debugfs_create_regset32()
|
|
Add the HW bit definition indecating goto chain offload support.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose port rate as part of the port speed register fields.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose the TLS encryption key general object type enum correctly,
and add the IPSec encryption key general object type enum.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add HCA_CAP.egress_acl_forward_to_vport field to check whether HW
supports e-switch vport's egress acl to forward packets to other
e-switch vport or not.
By default E-Switch egress ACL forwards eswitch vports egress packets
to their corresponding NIC/VF vports.
With this cap enabled, the driver is allowed to alter this behavior
and forward packets to arbitrary NIC/VF vports with the following
limitations:
a. Multiple processing paths are supported if all of the following
conditions are met:
- HCA_CAP.egress_acl_forward_to_vport is set ==1.
- A destination of type Flow Table only appears once, as the
last destination in the list.
- Vport destination is supported if
HCA_CAP.egress_acl_forward_to_vport==1. Vport must not be
the Uplink.
b. Flow_tag not supported.
c. This table is only applicable after an FDB table is created.
d. Push VLAN action is not supported.
e. Pop VLAN action cannot be added concurrently to this table and
FDB table.
This feature will be used during port failover in bonding scenario
where two VFs representors are bonded to handle failover egress traffic
(VM's ingress/receive traffic).
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull block fixes from Jens Axboe:
"Here are a few fixes that should go into this release. This contains:
- Revert of a bad bcache patch from this merge window
- Removed unused function (Daniel)
- Fixup for the blktrace fix from Jan from this release (Cengiz)
- Fix of deeper level bfqq overwrite in BFQ (Carlo)"
* tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
blktrace: fix dereference after null check
Revert "bcache: ignore pending signals when creating gc and allocator thread"
block: Remove used kblockd_schedule_work_on()
|
|
rhashtable_lookup_get_insert_key doesn't have a parameter `data`. It
does have a parameter `key`, however.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
|
|
Commit cd02cf1aceea ("mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC")
fixed memory hotplug with debug_pagealloc enabled, where onlining a page
goes through page freeing, which removes the direct mapping. Some arches
don't like when the page is not mapped in the first place, so
generic_online_page() maps it first. This is somewhat wasteful, but
better than special casing page freeing fast paths.
The commit however missed that DEBUG_PAGEALLOC configured doesn't mean
it's actually enabled. One has to test debug_pagealloc_enabled() since
031bc5743f15 ("mm/debug-pagealloc: make debug-pagealloc boottime
configurable"), or alternatively debug_pagealloc_enabled_static() since
8e57f8acbbd1 ("mm, debug_pagealloc: don't rely on static keys too early"),
but this is not done.
As a result, a s390 kernel with DEBUG_PAGEALLOC configured but not enabled
will crash:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:0000001ece13400b R2:000003fff7fd000b R3:000003fff7fcc007 S:000003fff7fd7000 P:000000000000013d
Oops: 0004 ilc:2 [#1] SMP
CPU: 1 PID: 26015 Comm: chmem Kdump: loaded Tainted: GX 5.3.18-5-default #1 SLE15-SP2 (unreleased)
Krnl PSW : 0704e00180000000 0000001ecd281b9e (__kernel_map_pages+0x166/0x188)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000000 0000000000000800 0000400b00000000 0000000000000100
0000000000000001 0000000000000000 0000000000000002 0000000000000100
0000001ece139230 0000001ecdd98d40 0000400b00000100 0000000000000000
000003ffa17e4000 001fffe0114f7d08 0000001ecd4d93ea 001fffe0114f7b20
Krnl Code: 0000001ecd281b8e: ec17ffff00d8 ahik %r1,%r7,-1
0000001ecd281b94: ec111dbc0355 risbg %r1,%r1,29,188,3
>0000001ecd281b9e: 94fb5006 ni 6(%r5),251
0000001ecd281ba2: 41505008 la %r5,8(%r5)
0000001ecd281ba6: ec51fffc6064 cgrj %r5,%r1,6,1ecd281b9e
0000001ecd281bac: 1a07 ar %r0,%r7
0000001ecd281bae: ec03ff584076 crj %r0,%r3,4,1ecd281a5e
Call Trace:
[<0000001ecd281b9e>] __kernel_map_pages+0x166/0x188
[<0000001ecd4d9516>] online_pages_range+0xf6/0x128
[<0000001ecd2a8186>] walk_system_ram_range+0x7e/0xd8
[<0000001ecda28aae>] online_pages+0x2fe/0x3f0
[<0000001ecd7d02a6>] memory_subsys_online+0x8e/0xc0
[<0000001ecd7add42>] device_online+0x5a/0xc8
[<0000001ecd7d0430>] state_store+0x88/0x118
[<0000001ecd5b9f62>] kernfs_fop_write+0xc2/0x200
[<0000001ecd5064b6>] vfs_write+0x176/0x1e0
[<0000001ecd50676a>] ksys_write+0xa2/0x100
[<0000001ecda315d4>] system_call+0xd8/0x2c8
Fix this by checking debug_pagealloc_enabled_static() before calling
kernel_map_pages(). Backports for kernel before 5.5 should use
debug_pagealloc_enabled() instead. Also add comments.
Fixes: cd02cf1aceea ("mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC")
Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Qian Cai <cai@lca.pw>
Link: http://lkml.kernel.org/r/20200224094651.18257-1-vbabka@suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As reported by Jann, ihold() does not in fact guarantee inode
persistence. And instead of making it so, replace the usage of inode
pointers with a per boot, machine wide, unique inode identifier.
This sequence number is global, but shared (file backed) futexes are
rare enough that this should not become a performance issue.
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
|
Several device drivers read their Device Serial Number from the PCIe
extended config space.
Introduce a new helper function, pci_get_dsn(). This function reads the
eight bytes of the DSN and returns them as a u64. If the capability does not
exist for the device, the function returns 0.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Invoke ndo_setup_tc() as appropriate to signal init / replacement,
destroying and dumping of pFIFO / bFIFO Qdisc.
A lot of the FIFO logic is used for pFIFO_head_drop as well, but that's a
semantically very different Qdisc that isn't really in the same boat as
pFIFO / bFIFO. Split some of the functions to keep the Qdisc intact.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.
To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.
This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.
The same mask is used for global and per queue settings.
v3: - move the (temporary) check if driver defines types
earlier (Michal)
- rename used_types -> nonzero_params, and
coalesce_types -> supported_coalesce_params (Alex)
- use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expose raw packet pacing APIs to be used by DEVX based applications.
The existing code was refactored to have a single flow with the new raw
APIs.
The new raw APIs considered the input of 'pp_rate_limit_context', uid,
'dedicated', upon looking for an existing entry.
This raw mode enables future device specification data in the raw
context without changing the existing logic and code.
The ability to ask for a dedicated entry gives control for application
to allocate entries according to its needs.
A dedicated entry may not be used by some other process and it also
enables the process spreading its resources to some different entries
for use different hardware resources as part of enforcing the rate.
The counter per entry was changed to be u64 to prevent any option to
overflow.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Several drivers use the following code sequence:
1. Read PCI_STATUS
2. Mask out non-error bits
3. Action based on error bits set
4. Write back set error bits to clear them
As this is a repeated pattern, add a helper to the PCI core.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This collection of PCI error bits is used in more than one driver,
so move it to the PCI core.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current fexit and fentry tests rely on a different program to
exercise the functions they attach to. Instead of doing this, implement
the test operations for tracing which will also be used for
BPF_MODIFY_RETURN in a subsequent patch.
Also, clean up the fexit test to use the generated skeleton.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200304191853.1529-7-kpsingh@chromium.org
|
|
When multiple programs are attached, each program receives the return
value from the previous program on the stack and the last program
provides the return value to the attached function.
The fmod_ret bpf programs are run after the fentry programs and before
the fexit programs. The original function is only called if all the
fmod_ret programs return 0 to avoid any unintended side-effects. The
success value, i.e. 0 is not currently configurable but can be made so
where user-space can specify it at load time.
For example:
int func_to_be_attached(int a, int b)
{ <--- do_fentry
do_fmod_ret:
<update ret by calling fmod_ret>
if (ret != 0)
goto do_fexit;
original_function:
<side_effects_happen_here>
} <--- do_fexit
The fmod_ret program attached to this function can be defined as:
SEC("fmod_ret/func_to_be_attached")
int BPF_PROG(func_name, int a, int b, int ret)
{
// This will skip the original function logic.
return 1;
}
The first fmod_ret program is passed 0 in its return argument.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200304191853.1529-4-kpsingh@chromium.org
|
|
As we need to introduce a third type of attachment for trampolines, the
flattened signature of arch_prepare_bpf_trampoline gets even more
complicated.
Refactor the prog and count argument to arch_prepare_bpf_trampoline to
use bpf_tramp_progs to simplify the addition and accounting for new
attachment types.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200304191853.1529-2-kpsingh@chromium.org
|
|
Add an API to check if a device has sync_state support in its driver or
bus.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20200221080510.197337-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce bpf_link abstraction, representing an attachment of BPF program to
a BPF hook point (e.g., tracepoint, perf event, etc). bpf_link encapsulates
ownership of attached BPF program, reference counting of a link itself, when
reference from multiple anonymous inodes, as well as ensures that release
callback will be called from a process context, so that users can safely take
mutex locks and sleep.
Additionally, with a new abstraction it's now possible to generalize pinning
of a link object in BPF FS, allowing to explicitly prevent BPF program
detachment on process exit by pinning it in a BPF FS and let it open from
independent other process to keep working with it.
Convert two existing bpf_link-like objects (raw tracepoint and tracing BPF
program attachments) into utilizing bpf_link framework, making them pinnable
in BPF FS. More FD-based bpf_links will be added in follow up patches.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200303043159.323675-2-andriin@fb.com
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dmar_drhd_units is traversed using list_for_each_entry_rcu()
outside of an RCU read side critical section but under the
protection of dmar_global_lock. Hence add corresponding lockdep
expression to silence the following false-positive warnings:
[ 1.603975] =============================
[ 1.603976] WARNING: suspicious RCU usage
[ 1.603977] 5.5.4-stable #17 Not tainted
[ 1.603978] -----------------------------
[ 1.603980] drivers/iommu/intel-iommu.c:4769 RCU-list traversed in non-reader section!!
[ 1.603869] =============================
[ 1.603870] WARNING: suspicious RCU usage
[ 1.603872] 5.5.4-stable #17 Not tainted
[ 1.603874] -----------------------------
[ 1.603875] drivers/iommu/dmar.c:293 RCU-list traversed in non-reader section!!
Tested-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit ee63cfa7fc19 ("block: add kblockd_schedule_work_on()")
introduced the helper in 2016. Remove it because since then no caller
was added.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes: 49644e68f472 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull KVM fixes from Paolo Bonzini:
"More bugfixes, including a few remaining "make W=1" issues such as too
large frame sizes on some configurations.
On the ARM side, the compiler was messing up shadow stacks between EL1
and EL2 code, which is easily fixed with __always_inline"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: check descriptor table exits on instruction emulation
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
arm64: Ask the compiler to __always_inline functions used by KVM at HYP
KVM: arm64: Define our own swab32() to avoid a uapi static inline
KVM: arm64: Ask the compiler to __always_inline functions used at HYP
kvm: arm/arm64: Fold VHE entry/exit work into kvm_vcpu_run_vhe()
KVM: arm/arm64: Fix up includes for trace.h
|
|
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-02-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 41 non-merge commits during the last 7 day(s) which contain
a total of 49 files changed, 1383 insertions(+), 499 deletions(-).
The main changes are:
1) BPF and Real-Time nicely co-exist.
2) bpftool feature improvements.
3) retrieve bpf_sk_storage via INET_DIAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
