| Age | Commit message (Collapse) | Author |
|---|
|
The generic IOMMU device-tree bindings can be used to add arbitrary OF
masters to an IOMMU with a compliant binding.
This patch introduces of_iommu_configure, which does exactly that.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch adds a new function to the iommu_ops structure to allow an
OF device to be added to a specific IOMMU instance using the recently
merged generic devicetree binding for IOMMUs. The callback (of_xlate)
takes a struct device representing the master and an of_phandle_args
representing the IOMMU and the correspondong IDs for the new master.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
set_arch_dma_coherent_ops is called from of_dma_configure in order to
swizzle the architectural dma-mapping functions over to a cache-coherent
implementation. This is currently implemented only for ARM.
In anticipation of re-using this mechanism for IOMMU-backed dma-mapping
ops too, this patch replaces the function with a broader
arch_setup_dma_ops callback which will be extended in future.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
IOMMU drivers must be initialised before any of their upstream devices,
otherwise the relevant iommu_ops won't be configured for the bus in
question. To solve this, a number of IOMMU drivers use initcalls to
initialise the driver before anything has a chance to be probed.
Whilst this solves the immediate problem, it leaves the job of probing
the IOMMU completely separate from the iommu_ops to configure the IOMMU,
which are called on a per-bus basis and require the driver to figure out
exactly which instance of the IOMMU is being requested. In particular,
the add_device callback simply passes a struct device to the driver,
which then has to parse firmware tables or probe buses to identify the
relevant IOMMU instance.
This patch takes the first step in addressing this problem by adding an
early initialisation pass for IOMMU drivers, giving them the ability to
store some per-instance data in their iommu_ops structure and store that
in their of_node. This can later be used when parsing OF masters to
identify the IOMMU instance in question.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Add support for simple on/off control of each channel.
To add regulator support, the pmbus part driver needs to add
regulator_desc information and number of regulators to its
pmbus_driver_info struct.
regulator_desc can be declared using default macro for a
regulator (PMBUS_REGULATOR) that is in pmbus.h
The regulator_init_data can be initialized from either
platform data or the device tree.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We need the xhci fixes here and this resolves a merge issue with
drivers/usb/dwc3/ep0.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
The function debugfs_create_devm_seqfile() has a parameter of type
struct device pointer. This type needs to be forward declared to
avoid compilation issues on certain architectures and/or kernel
configurations. The function was introduced with:
commit 98210b7f73f1db182bd9a558a031093cd166e907
Author: Arend van Spriel <arend@broadcom.com>
Date: Sun Nov 9 11:31:58 2014 +0100
debugfs: add helper function to create device related seq_file
The reported build failure for sparc64 architecture was:
make.cross ARCH=sparc64
All warnings:
In file included from fs/debugfs/file.c:21:0:
include/linux/debugfs.h:105:10: warning: 'struct device' declared
inside parameter list
void *data));
^
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Marvell EBU platforms, when doing suspend/resume, the SDRAM window
configuration must be saved on suspend, and restored on
resume. However, it needs to be restored on resume *before*
re-entering the kernel, because the SDRAM window configuration defines
the layout of the memory. For this reason, it cannot simply be done in
the ->suspend() and ->resume() hooks of the mvebu-mbus driver.
Instead, it needs to be restored by the bootloader "boot info"
mechanism used when resuming. This mechanism allows the kernel to
define a list of (address, value) pairs when suspending, that the
bootloader will restore on resume before jumping back into the kernel.
This commit therefore adds a new function to the mvebu-mbus driver,
called mvebu_mbus_save_cpu_target(), which will be called by the
platform code to make the mvebu-mbus driver save the SDRAM window
configuration in a way that can be understood by the bootloader "boot
info" mechanism.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-8-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
OPPs are created statically (from DT) or dynamically. Currently we don't free
OPPs that are created statically, when the module unloads. And so if the module
is inserted back again, we get warning for duplicate OPPs as the same were
already present.
Also, there might be a need to remove dynamic OPPs in future and so API for that
is also added.
This patch adds helper APIs to remove/free existing static and dynamic OPPs.
Because the OPPs are used both under RCU and SRCU, we have to wait for grace
period of both. And so are using kfree_rcu() from within call_srcu().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently there is no callback for cpufreq drivers which is called once the
policy is ready to be used. There are some requirements where such a callback is
required.
One of them is registering a cooling device with the help of
of_cpufreq_cooling_register(). This routine tries to get 'struct cpufreq_policy'
for CPUs which isn't yet initialed at the time ->init() is called and so we face
issues while registering the cooling device.
Because we can't register cooling device from ->init(), we need a callback that
is called after the policy is ready to be used and hence we introduce ->ready()
callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adding any new callback to 'struct cpufreq_driver' gives following checkpatch
warning:
WARNING: Unnecessary space before function pointer arguments
+ void (*ready) (struct cpufreq_policy *policy);
This is because we have been using a tab spacing between function pointer name
and its arguments and the new one tried to follow that.
Though we normally don't try to fix every checkpatch warning, specially around
formatting issues as that creates unnecessary noise over lists. But I thought we
better fix this so that new additions don't generate these warnings plus it
looks far better/symmetric now.
So, remove these tab spacing issues in 'struct cpufreq_driver' only + fix
alignment of all members.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into clk-next
Immutable branch between MFD, Regulator and Clk, due for v3.19
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/omap-gpmc
Pull "move omap gpmc to drivers finally" from Tony Lindgren:
We can finally move the GPMC code to live in drivers/memory for
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
* tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit
853a33ce6932 irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
Introduced a series of warnings when building ARM multi_v7_defconfig:
include/linux/irqchip/arm-gic.h:109:53: warning: its scope is only this definition or declaration, which is probably not what you want
In file included from arch/arm/mach-ux500/pm.c:13:0:
include/linux/irqchip/arm-gic.h:109:53: warning: 'struct irq_domain' declared inside parameter list
int gicv2m_of_init(struct device_node *node, struct irq_domain *parent);
^
Fix this by adding the proper include.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
[ jac merged much more correct version from Marc into this patch ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/1417170975-1163-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Now, with the CLCD DT support available, there is no
more reason to keep the non-DT support for V2P-CA9.
Removed, together with "some" supporting code. It was
necessary to make PLAT_VERSATILE_SCHED_CLOCK optional
and selected by the machines still interested in it.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Pull "The i.MX SoC update for 3.19" from Shawn Guo
- Update i.MX6 suspend code to check DDR instead of CPU type, as the
difference we need to handle is between LPDDR2 and DDR3, not SoCs.
- Set anatop properly for LPDDR2 in DSM mode
- Add support for new SoC LS1021A which integrates dual Cortex-A7
- Add ENET initialization for i.MX6SX platform
- Add cpufreq support for i.MX53 platform
- Add a SNVS based poweroff driver for i.MX6 platforms
- Use ARM Global Timer as clocksource on VF610
Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.
* tag 'imx-soc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
ARM: imx: clk-vf610: get input clocks from assigned clocks
ARM: imx: Add Freescale LS1021A SMP support
ARM: imx: Add initial support for Freescale LS1021A
ARM: imx53: add cpufreq support
ARM: imx53: clk: add ARM clock
ARM: imx: add CPU clock type
ARM: imx5: add step clock, used when reprogramming PLL1
ARM: imx: add enet init for i.mx6sx
ARM: imx6sx: add imx6sx iomux-gpr field define
ARM: vf610: Add ARM Global Timer clocksource option
ARM: imx: add anatop settings for LPDDR2 when enter DSM mode
ARM: imx: replace cpu type check with ddr type check
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
|
|
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new directory heirarchy under the debugfs sunrpc/ directory:
sunrpc/
rpc_xprt/
<xprt id>/
Within that directory, we can put files that give info about the
xprts. We do have the (minor) problem that there is no succinct,
unique identifier for rpc_xprts. So we generate them synthetically
with a static atomic_t counter.
For now, this directory just holds an "info" file, but we may add
other files to it in the future.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
It's possible to get a dump of the RPC task queue by writing a value to
/proc/sys/sunrpc/rpc_debug. If you write any value to that file, you get
a dump of the RPC client task list into the log buffer. This is a rather
inconvenient interface however, and makes it hard to get immediate info
about the task queue.
Add a new directory hierarchy under debugfs:
sunrpc/
rpc_clnt/
<clientid>/
Within each clientid directory we create a new "tasks" file that will
dump info similar to what shows up in the log buffer, but with a few
small differences -- we avoid printing raw kernel addresses in favor of
symbolic names and the XID is also displayed.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
|
|
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OMAP mailbox driver and its existing clients (remoteproc
for OMAP4+) are adapted to use the generic mailbox framework.
The main changes for the adaptation are:
- The tasklet used for Tx is replaced with the state machine from
the generic mailbox framework. The workqueue used for processing
the received messages stays intact for minimizing the effects on
the OMAP mailbox clients.
- The existing exported client API, omap_mbox_get, omap_mbox_put and
omap_mbox_send_msg are deleted, as the framework provides equivalent
functionality. A OMAP-specific omap_mbox_request_channel is added
though to support non-DT way of requesting mailboxes.
- The OMAP mailbox driver is integrated with the mailbox framework
through the proper implementations of mbox_chan_ops, except for
.last_tx_done and .peek_data. The OMAP mailbox driver does not need
these ops, as it is completely interrupt driven.
- The OMAP mailbox driver uses a custom of_xlate controller ops that
allows phandles for the pargs specifier instead of indexing to avoid
any channel registration order dependencies.
- The new framework does not support multiple clients operating on a
single channel, so the reference counting logic is simplified.
- The remoteproc driver (current client) is adapted to use the new API.
The notifier callbacks used within this client is replaced with the
regular callbacks from the newer framework.
- The exported OMAP mailbox API are limited to omap_mbox_save_ctx,
omap_mbox_restore_ctx, omap_mbox_enable_irq & omap_mbox_disable_irq,
with the signature modified to take in the new mbox_chan handle instead
of the OMAP specific omap_mbox handle. The first 2 will be removed when
the OMAP mailbox driver is adapted to runtime_pm. The other exported
API omap_mbox_request_channel will be removed once existing legacy
users are converted to DT.
Signed-off-by: Suman Anna <s-anna@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
If the mailbox controller expects the payload is in place before
initiating the transmit, then it's impossible to reuse the list
maintained by core mailbox code currently. Maintaining another list
for sending the message in the controller seems totally unnecessary
as core mailbox library already provides that feature.
This patch introduces tx_prepare callback in mbox_client which
can be used by the core mailbox library before initiating the
transaction through mbox->ops->send_data. The client driver can
implement this callback to ensure the payload is copied to the
shared memory.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add the equivalents to pr_<level>_once.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a helper function that simplifies adding a
so-called single_open sequence file for device drivers. The
calling device driver needs to provide a read function and
a device pointer. The field struct seq_file::private will
reference the device pointer upon call to the read function
so the driver can obtain his data from it and do its task
of providing the file content using seq_printf() calls and
alike. Using this helper function also gets rid of the need
to specify file operations per debugfs file.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These members of the driver structure are not present.
Remove them from the kernel-doc.
Cc: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fixes following minor issues in code comments in coresight.h
- typo %s/enpoint/endpoint
- alignment of comment section for struct coresight_desc
- correction of comment for struct coresight_connection and
struct coresight_device.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The acpi_table_parse() function has a callback that
passes a pointer to a table_header. Add a new function
which takes this pointer and parses its entries. This
eliminates the need to re-traverse all the tables for
each call. e.g. as in acpi_table_parse_madt() which is
normally called after acpi_table_parse().
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.linux-nfs.org/projects/anna/nfs-rdma into linux-next
Pull pull additional NFS client changes for 3.19 from Anna Schumaker:
"NFS: Generic client side changes from Chuck
These patches fixes for iostats and SETCLIENTID in addition to cleaning
up the nfs4_init_callback() function.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>"
* tag 'nfs-cel-for-3.19' of git://git.linux-nfs.org/projects/anna/nfs-rdma:
NFS: Clean up nfs4_init_callback()
NFS: SETCLIENTID XDR buffer sizes are incorrect
SUNRPC: serialize iostats updates
|
|
Linux 3.18-rc4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-max77802
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
|
|
Drivers can use the of_regulator_match() function to parse the regulator
init_data from DT. A match table is used to specify the name of the node
containing the regulators, the device node and to return the init_data
to the caller.
But also the static regulator descriptor is needed to correctly extract
some DT properties like the regulator initial and suspend modes. Use the
match table to pass that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "regulator-initial-mode" and "regulator-mode" DT properties allows
to configure the regulator operating modes at startup or when a system
enters into a susend state.
But these properties use as valid values the operating modes supported
by each device while the core deals with the standard operating modes.
So a mapping function is needed to translate from the hardware specific
modes to the standard ones.
This mapping is a non-varying configuration for each regulator, so add
a function pointer to struct regulator_desc that will allow drivers to
define their callback to do the modes translation.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All platforms now instantiate the DU through DT, platform data support
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.
This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ARM GICv2m specification extends GICv2 to support MSI(-X) with
a new register frame. This allows a GICv2 based system to support
MSI with minimal changes.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
[maz: converted the driver to use stacked irq domains,
updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416941243-7181-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
As the ITS is always a subsystem if GICv3, its probing/init is
driven by the main GICv3 code.
Plug that code in (guarded by a config option).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Now, the bit of code that allow us to use the ITS as a MSI controller.
Both MSI and MSI-X are supported.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ITS is configured through a number commands that the driver
issues to the HW using a memory-based circular buffer.
This patch implements the subset of commands that are required
for Linux.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The basic GICv3 driver has almost no use for the redistributor
(other than the basic per-CPU interrupts), but the ITS needs
a lot more from them.
As such, rework the set of data structures. The behaviour of the
GICv3 driver is otherwise unaffected.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
