| Age | Commit message (Collapse) | Author |
|---|
|
gpiochip_get_desc() takes a u16 hwnum, but it turns out most users don't
respect that and usually pass an unsigned int. Since implicit casting to
a smaller type is dangerous - let's change the type of hwnum to unsigned
int in gpiochip_get_desc() and in gpiochip_request_own_desc() where the
size of hwnum is not respected either and who's a user of the former.
This is safe as we then check the hwnum against the number of lines
before proceeding in gpiochip_get_desc().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
clk_set_rate() currently starts updating the rate for a clock at the
top-most affected clock and then walks down the tree to update the
bottom-most affected clock last.
This behavior is important for protected clocks where we can switch
between multiple parents to achieve the same output.
An example for this is the mali clock tree on Amlogic SoCs:
mali_0_mux (must not change when enabled)
mali_0_div (must not change when enabled)
mali_0 (gate)
mali_1_mux (must not change when enabled)
mali_1_div (must not change when enabled)
mali_1 (gate)
The final output can either use mali_0_gate or mali_1. To change the
final output we must switch to the "inactive" tree. Assuming mali_0 is
active, then we need to prepare mali_1 with the new desired rate and
finally switch the output to the mali_1 tree. This process will then
protect the mali_1 tree and at the same time unprotect the mali_0 tree.
The next call to clk_set_rate() will then switch from the mali_1 tree
back to mali_0.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
After commit fc0c209c147f ("clk: Allow parents to be specified without
string names") we can use DT or direct clk_hw pointers to specify
parents. Create a generic function that shouldn't be used very often to
encode the multitude of ways of registering a gate clk with different
parent information. Then add a bunch of wrapper macros that only pass
down what needs to be passed down to the generic function to support
this with less arguments.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-12-sboyd@kernel.org
|
|
After commit fc0c209c147f ("clk: Allow parents to be specified without
string names") we can use DT or direct clk_hw pointers to specify
parents. Create a generic function that shouldn't be used very often to
encode the multitude of ways of registering a mux clk with different
parent information. Then add a bunch of wrapper macros that only pass
down what needs to be passed down to the generic function to support
this with less arguments.
Note: the msm drm driver passes an anonymous array through the macro
which seems to confuse my compiler. Adding a parenthesis around the
whole thing at the call site seems to fix it but it must be wrong. Maybe
it's better to split this patch and pick out the array bits there?
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-11-sboyd@kernel.org
|
|
This kernel-doc talks about a rate for the accuracy. That's wrong.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-9-sboyd@kernel.org
|
|
Some clk providers want to use the accuracy of the parent clk and use
the fixed rate basic type clk to do that. This requires getting the
parent clk and extracting the accuracy before registering the fixed rate
clk. Let's add a flag for this and update the clk_ops to support this.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-8-sboyd@kernel.org
|
|
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"A few fixes for this cycle. The CMOS AltCentury support broke a few
platforms with a recent BIOS so I reverted it. The mt6397 fix is not
that critical but good to have. And finally, the sun6i fix repairs
WiFi and BT on a few platforms.
Summary:
- cmos: revert AltCentury support on AMD/Hygon
- mt6397: fix alarm register overwrite
- sun6i: ensure clock is working on R40"
* tag 'rtc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: cmos: Revert "rtc: Fix the AltCentury value on AMD/Hygon platform"
rtc: mt6397: fix alarm register overwrite
rtc: sun6i: Add support for RTC clocks on R40
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
ARM SCMI updates for v5.6
1. Addition of multiple device support per protocol to enable use of
some procotols by multiple kernel subsystems simultaneously and
corresponding updates to the existing scmi drivers
2. Addition of trace events around the scmi transfer code to measure
any delays and capture anomalies that can also be used during
investigation of some platform firmware related issues
* tag 'scmi-updates-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
drivers: firmware: scmi: Extend SCMI transport layer by trace events
include: trace: Add SCMI header with trace events
reset: reset-scmi: Match scmi device by both name and protocol id
hwmon: (scmi-hwmon) Match scmi device by both name and protocol id
cpufreq: scmi: Match scmi device by both name and protocol id
clk: scmi: Match scmi device by both name and protocol id
firmware: arm_scmi: Skip protocol initialisation for additional devices
firmware: arm_scmi: Stash version in protocol init functions
firmware: arm_scmi: Match scmi device by both name and protocol id
firmware: arm_scmi: Add versions and identifier attributes using dev_groups
firmware: arm_scmi: Add names to scmi devices created
firmware: arm_scmi: Skip scmi mbox channel setup for addtional devices
firmware: arm_scmi: Add support for multiple device per protocol
Link: https://lore.kernel.org/r/20191230182956.GA29349@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit bc081dd6e9f6 ("kbuild: generate modules.builtin") added
infrastructure to generate modules.builtin, the list of all
builtin modules.
Basically, it works like this:
- Kconfig generates include/config/tristate.conf, the list of
tristate CONFIG options with a value in a capital letter.
- scripts/Makefile.modbuiltin makes Kbuild descend into
directories to collect the information of builtin modules.
I am not a big fan of it because Kbuild ends up with traversing
the source tree twice.
I am not sure how perfectly it should work, but this approach cannot
avoid false positives; even if the relevant CONFIG option is tristate,
some Makefiles forces obj-m to obj-y.
Some examples are:
arch/powerpc/platforms/powermac/Makefile:
obj-$(CONFIG_NVRAM:m=y) += nvram.o
net/ipv6/Makefile:
obj-$(subst m,y,$(CONFIG_IPV6)) += inet6_hashtables.o
net/netlabel/Makefile:
obj-$(subst m,y,$(CONFIG_IPV6)) += netlabel_calipso.o
Nobody has complained about (or noticed) it, so it is probably fine to
have false positives in modules.builtin.
This commit simplifies the implementation. Let's exploit the fact
that every module has MODULE_LICENSE(). (modpost shows a warning if
MODULE_LICENSE is missing. If so, 0-day bot would already have blocked
such a module.)
I added MODULE_FILE to <linux/module.h>. When the code is being compiled
as builtin, it will be filled with the file path of the module, and
collected into modules.builtin.info. Then, scripts/link-vmlinux.sh
extracts the list of builtin modules out of it.
This new approach fixes the false-positives above, but adds another
type of false-positives; non-modular code may have MODULE_LICENSE()
by mistake. This is not a big deal, it is just the code is always
orphan. We can clean it up if we like. You can see cleanup examples by:
$ git log --grep='make.* explicitly non-modular'
To sum up, this commits deletes lots of code, but still produces almost
equivalent results. Please note it does not increase the vmlinux size at
all. As you can see in include/asm-generic/vmlinux.lds.h, the .modinfo
section is discarded in the link stage.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
The check in block_page_mkwrite that is meant to determine whether an
offset is within the inode size is off by one. This bug has been copied
into iomap_page_mkwrite and several filesystems (ubifs, ext4, f2fs,
ceph).
Fix that by introducing a new page_mkwrite_check_truncate helper that
checks for truncate and computes the bytes in the page up to EOF. Use
the helper in iomap.
NOTE from Darrick: The original patch fixed a number of filesystems, but
then there were merge conflicts with the f2fs for-next tree; a
subsequent re-submission of the patch had different btrfs changes with
no explanation; and Christoph complained that each per-fs fix should be
a separate patch. In my view that's too much risk to take on, so I
decided to drop all the hunks except for iomap, since I've actually QA'd
XFS.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: drop everything but the iomap parts]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Requested, and we need v5.5-rc1 backported as our current branch is still based on v5.4.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add few more stubs (for OCMEM-related functions and
qcom_scm_restore_sec_cfg_available()) in case of !CONFIG_QCOM_SCM.
These are actually not necessary for builds but provide them for
completeness.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103220825.28710-1-krzk@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Within the LS1028A SoC, the register map for the ENETC MDIO controller
is instantiated a few times: for the central (external) MDIO controller,
for the internal bus of each standalone ENETC port, and for the internal
bus of the Felix switch.
Refactoring is needed to support multiple MDIO buses from multiple
drivers. The enetc_hw structure is made an opaque type and a smaller
enetc_mdio_priv is created.
'mdio_base' - MDIO registers base address - is being parameterized, to
be able to work with different MDIO register bases.
The ENETC MDIO bus operations are exported from the fsl-enetc-mdio
kernel object, the same that registers the central MDIO controller (the
dedicated PF). The ENETC main driver has been changed to select it, and
use its exported helpers to further register its private MDIO bus. The
DSA Felix driver will do the same.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some MAC PCS blocks are unable to provide interrupts when their status
changes. As we already have support in phylink for polling status, use
this to provide a hook for MACs to enable polling mode.
The patch idea was picked up from Russell King's suggestion on the macb
phylink patch thread here [0] but the implementation was changed.
Instead of introducing a new phylink_start_poll() function, which would
make the implementation cumbersome for common PHYLINK implementations
for multiple types of devices, like DSA, just add a boolean property to
the phylink_config structure, which is just as backwards-compatible.
https://lkml.org/lkml/2019/12/16/603
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Typically a MAC PCS auto-configures itself after it receives the
negotiated copper-side link settings from the PHY, but some MAC devices
are more special and need manual interpretation of the SGMII AN result.
In other cases, the PCS exposes the entire tx_config_reg base page as it
is transmitted on the wire during auto-negotiation, so it makes sense to
be able to decode the equivalent lp_advertised bit mask from the raw u16
(of course, "lp" considering the PCS to be the local PHY).
Therefore, add the bit definitions for the SGMII registers 4 and 5
(local device ability, link partner ability), as well as a link_mode
conversion helper that can be used to feed the AN results into
phy_resolve_aneg_linkmode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the LED is acquired by a consumer device with devm_led_get(), it is
automatically released when the device is detached.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
This patch adds basic support for a kernel driver to get a LED device.
This will be used by the led-backlight driver.
Only OF version is implemented for now, and the behavior is similar to
PWM's of_pwm_get() and pwm_put().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.
The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.
My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.
Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:
Send mgmt frame 1 through S0: S0 x x x
Send mgmt frame 2 through S1: S0 S1 x x
Send mgmt frame 3 through S2: S0 S1 S2 x
Send mgmt frame 4 through S3: S0 S1 S2 S3
The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.
So there is a potential throughput benefit here.
But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.
And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.
Useless.
Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.
So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.
While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent discussion has revealed that the use of PHY_INTERFACE_MODE_10GKR
is incorrect. Add a 10GBASE-R definition, document both the -R and -KR
versions, and the fact that 10GKR was used incorrectly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit fc0c209c147f ("clk: Allow parents to be specified without
string names") we can use DT or direct clk_hw pointers to specify
parents. Create a generic function that shouldn't be used very often to
encode the multitude of ways of registering a fixed rate clk with
different parent information. Then add a bunch of wrapper macros that
only pass down what needs to be passed down to the generic function to
support this with less arguments.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-7-sboyd@kernel.org
|
|
This member isn't documented, leading to kernel-doc warnings. Document
it.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-6-sboyd@kernel.org
|
|
The only user of this macro is the fixed rate basic type. Move it there
to avoid polluting provider drivers.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-5-sboyd@kernel.org
|
|
There aren't any users of this API anymore. Remove it.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-4-sboyd@kernel.org
|
|
Nobody has used the gpio clk registration functions nor the gpio clk_ops
exposed by the basic gpio clk type. Let's remove all those APIs and move
the gpio clk support into the C file. Since nothing is using the
exported APIs, simplify the driver to be a platform driver that uses
clk_parent_data to pick 0th or 1st cell of the node's clocks property.
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-2-sboyd@kernel.org
|
|
After commit 85a8ce62c2ea ("block: add bio_truncate to fix guard_bio_eod")
this function is unused, remove it.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We currently try to shrink a single zone when removing memory. We use
the zone of the first page of the memory we are removing. If that
memmap was never initialized (e.g., memory was never onlined), we will
read garbage and can trigger kernel BUGs (due to a stale pointer):
BUG: unable to handle page fault for address: 000000000000353d
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.3.0-rc5-next-20190820+ #317
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.4
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
RIP: 0010:clear_zone_contiguous+0x5/0x10
Code: 48 89 c6 48 89 c3 e8 2a fe ff ff 48 85 c0 75 cf 5b 5d c3 c6 85 fd 05 00 00 01 5b 5d c3 0f 1f 840
RSP: 0018:ffffad2400043c98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000200000000 RCX: 0000000000000000
RDX: 0000000000200000 RSI: 0000000000140000 RDI: 0000000000002f40
RBP: 0000000140000000 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000140000
R13: 0000000000140000 R14: 0000000000002f40 R15: ffff9e3e7aff3680
FS: 0000000000000000(0000) GS:ffff9e3e7bb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000353d CR3: 0000000058610000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__remove_pages+0x4b/0x640
arch_remove_memory+0x63/0x8d
try_remove_memory+0xdb/0x130
__remove_memory+0xa/0x11
acpi_memory_device_remove+0x70/0x100
acpi_bus_trim+0x55/0x90
acpi_device_hotplug+0x227/0x3a0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x221/0x550
worker_thread+0x50/0x3b0
kthread+0x105/0x140
ret_from_fork+0x3a/0x50
Modules linked in:
CR2: 000000000000353d
Instead, shrink the zones when offlining memory or when onlining failed.
Introduce and use remove_pfn_range_from_zone(() for that. We now
properly shrink the zones, even if we have DIMMs whereby
- Some memory blocks fall into no zone (never onlined)
- Some memory blocks fall into multiple zones (offlined+re-onlined)
- Multiple memory blocks that fall into different zones
Drop the zone parameter (with a potential dubious value) from
__remove_pages() and __remove_section().
Link: http://lkml.kernel.org/r/20191006085646.5768-6-david@redhat.com
Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: <stable@vger.kernel.org> [5.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"A bunch of fixes for:
- uninitialized dma_slave_caps access
- virt-dma use after free in vchan_complete()
- driver fixes for ioat, k3dma and jz4780"
* tag 'dmaengine-fix-5.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
ioat: ioat_alloc_ring() failure handling.
dmaengine: virt-dma: Fix access after free in vchan_complete()
dmaengine: k3dma: Avoid null pointer traversal
dmaengine: dma-jz4780: Also break descriptor chains on JZ4725B
dmaengine: Fix access to uninitialized dma_slave_caps
|
|
The AMD-TEE driver should check if TEE is available before
registering itself with TEE subsystem. This ensures that
there is a TEE which the driver can talk to before proceeding
with tee device node allocation.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Co-developed-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Signed-off-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ingress checksum offload was not working for IPv6 frames because the
conditional expression that checks validation status passed from the
hardware was not matching the algorithm described in the documentation.
This patch defines L4_CSUM flag (which falls inside the badfcs_enc field
in the existing definition of the CQE layout) and replaces the conditional
expression with the one defined in the "ConnectX(r) Family Programmer's
Manual" document.
Link: https://lore.kernel.org/r/20191219134847.413582-1-leon@kernel.org
Signed-off-by: Eugene Crosser <evgenii.cherkashin@profitbricks.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"Three fixes in here:
- Fix for a missing split on default memory boundary mask (4G) (Ming)
- Fix for multi-page read bio truncate (Ming)
- Fix for null_blk zone close request handling (Damien)"
* tag 'block-5.5-20200103' of git://git.kernel.dk/linux-block:
null_blk: Fix REQ_OP_ZONE_CLOSE handling
block: fix splitting segments on boundary masks
block: add bio_truncate to fix guard_bio_eod
|
|
As of now dax_writeback_mapping_range() takes "struct block_device" as a
parameter and dax_dev is searched from bdev name. This also involves taking
a fresh reference on dax_dev and putting that reference at the end of
function.
We are developing a new filesystem virtio-fs and using dax to access host
page cache directly. But there is no block device. IOW, we want to make
use of dax but want to get rid of this assumption that there is always
a block device associated with dax_dev.
So pass in "struct dax_device" as parameter instead of bdev.
ext2/ext4/xfs are current users and they already have a reference on
dax_device. So there is no need to take reference and drop reference to
dax_device on each call of this function.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Link: https://lore.kernel.org/r/20200103183307.GB13350@redhat.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Probably most useful if you want no logo at all, or if you only want one
logo regardless of how many CPU cores you have.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827110854.12574-3-peda@axentia.se
|
|
The ata_sas_scsi_ioctl() function implements a number of HDIO_* commands
for SCSI devices, it is used by all libata drivers as well as a few
drivers that support SAS attached SATA drives.
The only command that is not safe for compat ioctls here is
HDIO_GET_32BIT. Change the implementation to check for in_compat_syscall()
in order to do both cases correctly, and change all callers to use it
as both native and compat callback pointers, including the indirect
callers through sas_ioctl and ata_scsi_ioctl.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now that both native and compat ioctl syscalls are
in the same file, a couple of simplifications can
be made, bringing the implementation closer together:
- do_vfs_ioctl(), ioctl_preallocate(), and compat_ioctl_preallocate()
can become static, allowing the compiler to optimize better
- slightly update the coding style for consistency between
the functions.
- rather than listing each command in two switch statements
for the compat case, just call a single function that has
all the common commands.
As a side-effect, FS_IOC_RESVSP/FS_IOC_RESVSP64 are now available
to x86 compat tasks, along with FS_IOC_RESVSP_32/FS_IOC_RESVSP64_32.
This is harmless for i386 emulation, and can be considered a bugfix
for x32 emulation, which never supported these in the past.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Rather than relying on fs/compat_ioctl.c, this adds support
for a compat_ioctl() callback in the ide-floppy driver directly,
which lets it translate the scsi commands.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A lot of block drivers need only a trivial .compat_ioctl callback.
Add a helper function that can be set as the callback pointer
to only convert the argument using the compat_ptr() conversion
and otherwise assume all input and output data is compatible,
or handled using in_compat_syscall() checks.
This mirrors the compat_ptr_ioctl() helper function used in
character devices.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
In order to avoid needless #ifdef CONFIG_COMPAT checks,
move the compat_ptr() definition to linux/compat.h
where it can be seen by any file regardless of the
architecture.
Only s390 needs a special definition, this can use the
self-#define trick we have elsewhere.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a common header for the SiP service interface in MediaTek Chipsets.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-2-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull final sizeof_field conversion from Kees Cook:
"Remove now unused FIELD_SIZEOF() macro (Kees Cook)"
* tag 'sizeof_field-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kernel.h: Remove unused FIELD_SIZEOF()
|
|
This reverts commit 8243186f0cc7 ("fs: remove ksys_dup()") and the
subsequent fix for it in commit 2d3145f8d280 ("early init: fix error
handling when opening /dev/console").
Trying to use filp_open() and f_dupfd() instead of pseudo-syscalls
caused more trouble than what is worth it: it requires accessing vfs
internals and it turns out there were other bugs in it too.
In particular, the file reference counting was wrong - because unlike
the original "open+2*dup" sequence it used "filp_open+3*f_dupfd" and
thus had an extra leaked file reference.
That in turn then caused odd problems with Androidx86 long after boot
becaue of how the extra reference to the console kept the session active
even after all file descriptors had been closed.
Reported-by: youling 257 <youling257@gmail.com>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We already have the of_genpd_add_subdomain() helper, but no corresponding
of_genpd_remove_subdomain(), so let's add it. Subsequent changes starts to
make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
|
|
When the hierarchical CPU topology is used and when a CPU is put offline,
that CPU prevents its PM domain from being powered off, which is because
genpd observes the corresponding attached device as being active from a
runtime PM point of view. Furthermore, any potential master PM domains are
also prevented from being powered off.
To address this limitation, let's add add a new CPU hotplug state
(CPUHP_AP_CPU_PM_STARTING) and register up/down callbacks for it, which
allows us to deal with runtime PM accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
|
|
The CPU's idle state nodes are currently parsed at the common cpuidle DT
library, but also when initializing data for specific CPU idle operations,
as in the PSCI cpuidle driver case and qcom-spm cpuidle case.
To avoid open-coding, let's introduce of_get_cpu_state_node(), which takes
the device node for the CPU and the index to the requested idle state node,
as in-parameters. In case a corresponding idle state node is found, it
returns the node with the refcount incremented for it, else it returns
NULL.
Moreover, for PSCI there are two options to describe the CPU's idle states
[1], either via a flattened description or a hierarchical layout. Hence,
let's take both options into account.
[1] Documentation/devicetree/bindings/arm/psci.yaml
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
To allow subsequent changes to implement support for OSI mode through the
cpuidle-psci driver, export the existing psci_has_osi_support(). Export
also a new function, psci_set_osi_mode(), that allows its caller to enable
the OS-initiated CPU-suspend mode in the PSCI FW.
To deal with backwards compatibility for a kernel started through a kexec
call, default to set the CPU-suspend mode to the Platform Coordinated mode
during boot.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
|
