| Age | Commit message (Collapse) | Author |
|---|
|
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TPS61050/TPS61052 are boost converters, LED drivers, LED flash
drivers and a simple GPIO pin chips.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds support for ab8500 chip revision cut 3.0.
Also rephrased from Changes to Author in the header.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
If a system contains multiple WM831x devices we need to pass a device
number through to the MFD so that we use unique device IDs when we
instantiate child devices. In order to get support for this into 2.6.39
add some platform data to support the configuration, but no implementation
as yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Introducing a driver for MADC on TWL4030 powerIC. MADC stands for monitoring
ADC. This driver monitors the real time conversion of analog signals like
battery temperature, battery cuurent etc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This adds functions to enable platform_device sharing for mfd clients.
Each platform driver (mfd client) that wants to share an mfd_cell's
platform_device uses the mfd_shared_platform_driver_{un,}register()
functions instead of platform_driver_{un,}register(). Along with
registering the platform driver, these also register a new platform
device with the same characteristics as the original cell, but a different
name. Given an mfd_cell with the name "foo", drivers that want to
share access to its resources can call mfd_shared_platform_driver_register
with platform drivers named (for example) "bar" and "baz". This
will register two platform devices and drivers named "bar" and "baz"
that share the same cell as the platform device "foo". The drivers
can then call "foo" cell's enable hooks (or mfd_shared_cell_enable)
to enable resources, and obtain platform resources as they normally
would.
This deals with platform handling only; mfd driver-specific details,
hardware handling, refcounting, etc are all dealt with separately.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This provides convenience functions for sharing of cells across
multiple mfd clients. Mfd drivers can provide enable/disable hooks
to actually tweak the hardware, and clients can call
mfd_shared_cell_{en,dis}able without having to worry about whether
or not another client happens to have enabled or disabled the
cell/hardware.
Note that this is purely optional; drivers can continue to use
the mfd_cell's enable/disable hooks for their own purposes, if
desired.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
All users of this have now been switched over to using mfd_data;
it can go away now.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Rename the platform_data variable to imply a distinction between
common platform_data driver usage (typically accessed via
pdev->dev.platform_data) and the way MFD passes data down to
clients (using a wrapper named mfd_get_data).
All clients have already been changed to use the wrapper function,
so this can be a quick single-commit change that only touches things
in drivers/mfd.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Now that there are no more users of this, drop it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack. In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
No clients (in mainline kernel, I'm told that drivers exist in external
trees that are planned for mainline inclusion) make use of this, nor
do they make use of platform_data, so nothing really had to change here.
The .data_size field is unused, so its usage gets removed.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Previously, one would set the mfd_cell's platform_data/data_size to point
to the current mfd_cell in order to pass that information along to drivers.
This causes the current mfd_cell to always be available to drivers. It
also adds a wrapper function for fetching the mfd cell from a platform
device, similar to what originally existed for mfd devices.
Drivers who previously used platform_data for other purposes can still
use it; the difference is that mfd_get_data() must be used to
access it (and the pdata structure is no longer allocated in
mfd_add_devices).
Note that mfd_get_data is intentionally vague (in name) about where
the data is stored; variable name changes can come later without having
to touch brazillions of drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This adds a pretty straight-forward system control driver for the
AB8500. This driver will be used from the core platform, e.g the
clock tree implementation in the machine code, and is by nature
singleton.
There are a few simple functions to read, write, set and clear
registers so that the machine code can control its own foundation.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Currently, if the task is STOPPED on ptrace attach, it's left alone
and the state is silently changed to TRACED on the next ptrace call.
The behavior breaks the assumption that arch_ptrace_stop() is called
before any task is poked by ptrace and is ugly in that a task
manipulates the state of another task directly.
With GROUP_STOP_PENDING, the transitions between TASK_STOPPED and
TRACED can be made clean. The tracer can use the flag to tell the
tracee to retry stop on attach and detach. On retry, the tracee will
enter the desired state in the correct way. The lower 16bits of
task->group_stop is used to remember the signal number which caused
the last group stop. This is used while retrying for ptrace attach as
the original group_exit_code could have been consumed with wait(2) by
then.
As the real parent may wait(2) and consume the group_exit_code
anytime, the group_exit_code needs to be saved separately so that it
can be used when switching from regular sleep to ptrace_stop(). This
is recorded in the lower 16bits of task->group_stop.
If a task is already stopped and there's no intervening SIGCONT, a
ptrace request immediately following a successful PTRACE_ATTACH should
always succeed even if the tracer doesn't wait(2) for attach
completion; however, with this change, the tracee might still be
TASK_RUNNING trying to enter TASK_TRACED which would cause the
following request to fail with -ESRCH.
This intermediate state is hidden from the ptracer by setting
GROUP_STOP_TRAPPING on attach and making ptrace_check_attach() wait
for it to clear on its signal->wait_chldexit. Completing the
transition or getting killed clears TRAPPING and wakes up the tracer.
Note that the STOPPED -> RUNNING -> TRACED transition is still visible
to other threads which are in the same group as the ptracer and the
reverse transition is visible to all. Please read the comments for
details.
Oleg:
* Spotted a race condition where a task may retry group stop without
proper bookkeeping. Fixed by redoing bookkeeping on retry.
* Spotted that the transition is visible to userland in several
different ways. Most are fixed with GROUP_STOP_TRAPPING. Unhandled
corner case is documented.
* Pointed out not setting GROUP_STOP_SIGMASK on an already stopped
task would result in more consistent behavior.
* Pointed out that calling ptrace_stop() from do_signal_stop() in
TASK_STOPPED can race with group stop start logic and then confuse
the TRAPPING wait in ptrace_check_attach(). ptrace_stop() is now
called with TASK_RUNNING.
* Suggested using signal->wait_chldexit instead of bit wait.
* Spotted a race condition between TRACED transition and clearing of
TRAPPING.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
|
|
Currently task->signal->group_stop_count is used to decide whether to
stop for group stop. However, if there is a task in the group which
is taking a long time to stop, other tasks which are continued by
ptrace would repeatedly stop for the same group stop until the group
stop is complete.
Conversely, if a ptraced task is in TASK_TRACED state, the debugger
won't get notified of group stops which is inconsistent compared to
the ptraced task in any other state.
This patch introduces GROUP_STOP_PENDING which tracks whether a task
is yet to stop for the group stop in progress. The flag is set when a
group stop starts and cleared when the task stops the first time for
the group stop, and consulted whenever whether the task should
participate in a group stop needs to be determined. Note that now
tasks in TASK_TRACED also participate in group stop.
This results in the following behavior changes.
* For a single group stop, a ptracer would see at most one stop
reported.
* A ptracee in TASK_TRACED now also participates in group stop and the
tracer would get the notification. However, as a ptraced task could
be in TASK_STOPPED state or any ptrace trap could consume group
stop, the notification may still be missing. These will be
addressed with further patches.
* A ptracee may start a group stop while one is still in progress if
the tracer let it continue with stop signal delivery. Group stop
code handles this correctly.
Oleg:
* Spotted that a task might skip signal check even when its
GROUP_STOP_PENDING is set. Fixed by updating
recalc_sigpending_tsk() to check GROUP_STOP_PENDING instead of
group_stop_count.
* Pointed out that task->group_stop should be cleared whenever
task->signal->group_stop_count is cleared. Fixed accordingly.
* Pointed out the behavior inconsistency between TASK_TRACED and
RUNNING and the last behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
|
|
task->signal->group_stop_count is used to track the progress of group
stop. It's initialized to the number of tasks which need to stop for
group stop to finish and each stopping or trapping task decrements.
However, each task doesn't keep track of whether it decremented the
counter or not and if woken up before the group stop is complete and
stops again, it can decrement the counter multiple times.
Please consider the following example code.
static void *worker(void *arg)
{
while (1) ;
return NULL;
}
int main(void)
{
pthread_t thread;
pid_t pid;
int i;
pid = fork();
if (!pid) {
for (i = 0; i < 5; i++)
pthread_create(&thread, NULL, worker, NULL);
while (1) ;
return 0;
}
ptrace(PTRACE_ATTACH, pid, NULL, NULL);
while (1) {
waitid(P_PID, pid, NULL, WSTOPPED);
ptrace(PTRACE_SINGLESTEP, pid, NULL, (void *)(long)SIGSTOP);
}
return 0;
}
The child creates five threads and the parent continuously traps the
first thread and whenever the child gets a signal, SIGSTOP is
delivered. If an external process sends SIGSTOP to the child, all
other threads in the process should reliably stop. However, due to
the above bug, the first thread will often end up consuming
group_stop_count multiple times and SIGSTOP often ends up stopping
none or part of the other four threads.
This patch adds a new field task->group_stop which is protected by
siglock and uses GROUP_STOP_CONSUME flag to track which task is still
to consume group_stop_count to fix this bug.
task_clear_group_stop_pending() and task_participate_group_stop() are
added to help manipulating group stop states. As ptrace_stop() now
also uses task_participate_group_stop(), it will set
SIGNAL_STOP_STOPPED if it completes a group stop.
There still are many issues regarding the interaction between group
stop and ptrace. Patches to address them will follow.
- Oleg spotted duplicate GROUP_STOP_CONSUME. Dropped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
|
|
tracehook_notify_jctl() aids in determining whether and what to report
to the parent when a task is stopped or continued. The function also
adds an extra requirement that siglock may be released across it,
which is currently unused and quite difficult to satisfy in
well-defined manner.
As job control and the notifications are about to receive major
overhaul, remove the tracehook and open code it. If ever necessary,
let's factor it out after the overhaul.
* Oleg spotted incorrect CLD_CONTINUED/STOPPED selection when ptraced.
Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
|
|
Conflicts:
arch/x86/kernel/acpi/sleep.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
With recent changes to the driver(switch to new cpdma layer),
the support for buffer descriptor address translation logic
is broken. This affects platforms where the physical address of
the descriptors as seen by the DMA engine is different from the
physical address.
Original Patch adding translation logic support:
Commit: ad021ae8862209864dc8ebd3b7d3a55ce84b9ea2
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Tested-By: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (66 commits)
avr32: at32ap700x: fix typo in DMA master configuration
dmaengine/dmatest: Pass timeout via module params
dma: let IMX_DMA depend on IMX_HAVE_DMA_V1 instead of an explicit list of SoCs
fsldma: make halt behave nicely on all supported controllers
fsldma: reduce locking during descriptor cleanup
fsldma: support async_tx dependencies and automatic unmapping
fsldma: fix controller lockups
fsldma: minor codingstyle and consistency fixes
fsldma: improve link descriptor debugging
fsldma: use channel name in printk output
fsldma: move related helper functions near each other
dmatest: fix automatic buffer unmap type
drivers, pch_dma: Fix warning when CONFIG_PM=n.
dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writel
avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msize
dw_dmac: Setting Default Burst length for transfers as 16.
dw_dmac: Allow src/dst msize & flow controller to be configured at runtime
dw_dmac: Changing type of src_master and dest_master to u8.
dw_dmac: Pass Channel Priority from platform_data
dw_dmac: Pass Channel Allocation Order from platform_data
...
|
|
Instead of always creating a huge (268K) deflate_workspace with the
maximum compression parameters (windowBits=15, memLevel=8), allow the
caller to obtain a smaller workspace by specifying smaller parameter
values.
For example, when capturing oops and panic reports to a medium with
limited capacity, such as NVRAM, compression may be the only way to
capture the whole report. In this case, a small workspace (24K works
fine) is a win, whether you allocate the workspace when you need it (i.e.,
during an oops or panic) or at boot time.
I've verified that this patch works with all accepted values of windowBits
(positive and negative), memLevel, and compression level.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add brackets around typecasted argument in crc32() macro.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Analog Devices' SigmaStudio can produce firmware blobs for devices with
these DSPs embedded (like some audio codecs). Allow these device drivers
to easily parse and load them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
1. simple_strto*() do not contain overflow checks and crufty,
libc way to indicate failure.
2. strict_strto*() also do not have overflow checks but the name and
comments pretend they do.
3. Both families have only "long long" and "long" variants,
but users want strtou8()
4. Both "simple" and "strict" prefixes are wrong:
Simple doesn't exactly say what's so simple, strict should not exist
because conversion should be strict by default.
The solution is to use "k" prefix and add convertors for more types.
Enter
kstrtoull()
kstrtoll()
kstrtoul()
kstrtol()
kstrtouint()
kstrtoint()
kstrtou64()
kstrtos64()
kstrtou32()
kstrtos32()
kstrtou16()
kstrtos16()
kstrtou8()
kstrtos8()
Include runtime testsuite (somewhat incomplete) as well.
strict_strto*() become deprecated, stubbed to kstrto*() and
eventually will be removed altogether.
Use kstrto*() in code today!
Note: on some archs _kstrtoul() and _kstrtol() are left in tree, even if
they'll be unused at runtime. This is temporarily solution,
because I don't want to hardcode list of archs where these
functions aren't needed. Current solution with sizeof() and
__alignof__ at least always works.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move setup_nr_cpu_ids(), smp_init() and some other SMP boot parameter
setup functions from init/main.c to kenrel/smp.c, saves some #ifdef
CONFIG_SMP.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Rakib Mullick <rakib.mullick@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PTR_RET() can be used if you have an error-pointer and are only interested
in the eventual error value, but not the pointer. Yields the usual 0 for
no error, -ESOMETHING otherwise.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Re-ordering struct block_inode to remove 8 bytes of padding on 64 bit
builds, which also shrinks bdev_inode by 8 bytes (776 -> 768) allowing it
to fit into one fewer cache lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Unify identical gcc3.x and gcc4.x macros.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new __GFP_OTHER_NODE flag to tell the low level numa statistics in
zone_statistics() that an allocation is on behalf of another thread. This
way the local and remote counters can be still correct, even when
background daemons like khugepaged are changing memory mappings.
This only affects the accounting, but I think it's worth doing that right
to avoid confusing users.
I first tried to just pass down the right node, but this required a lot of
changes to pass down this parameter and at least one addition of a 10th
argument to a 9 argument function. Using the flag is a lot less
intrusive.
Open: should be also used for migration?
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
balancing small zones
When reclaiming for order-0 pages, kswapd requires that all zones be
balanced. Each cycle through balance_pgdat() does background ageing on
all zones if necessary and applies equal pressure on the inactive zone
unless a lot of pages are free already.
A "lot of free pages" is defined as a "balance gap" above the high
watermark which is currently 7*high_watermark. Historically this was
reasonable as min_free_kbytes was small. However, on systems using huge
pages, it is recommended that min_free_kbytes is higher and it is tuned
with hugeadm --set-recommended-min_free_kbytes. With the introduction of
transparent huge page support, this recommended value is also applied. On
X86-64 with 4G of memory, min_free_kbytes becomes 67584 so one would
expect around 68M of memory to be free. The Normal zone is approximately
35000 pages so under even normal memory pressure such as copying a large
file, it gets exhausted quickly. As it is getting exhausted, kswapd
applies pressure equally to all zones, including the DMA32 zone. DMA32 is
approximately 700,000 pages with a high watermark of around 23,000 pages.
In this situation, kswapd will reclaim around (23000*8 where 8 is the high
watermark + balance gap of 7 * high watermark) pages or 718M of pages
before the zone is ignored. What the user sees is that free memory far
higher than it should be.
To avoid an excessive number of pages being reclaimed from the larger
zones, explicitely defines the "balance gap" to be either 1% of the zone
or the low watermark for the zone, whichever is smaller. While kswapd
will check all zones to apply pressure, it'll ignore zones that meets the
(high_wmark + balance_gap) watermark.
To test this, 80G were copied from a partition and the amount of memory
being used was recorded. A comparison of a patch and unpatched kernel can
be seen at
http://www.csn.ul.ie/~mel/postings/minfree-20110222/memory-usage-hydra.ps
and shows that kswapd is not reclaiming as much memory with the patch
applied.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Chen, Tim C" <tim.c.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now, if a mm_walk has either ->pte_entry or ->pmd_entry set, it will
unconditionally split any transparent huge pages it runs in to. In
practice, that means that anyone doing a
cat /proc/$pid/smaps
will unconditionally break down every huge page in the process and depend
on khugepaged to re-collapse it later. This is fairly suboptimal.
This patch changes that behavior. It teaches each ->pmd_entry handler
(there are five) that they must break down the THPs themselves. Also, the
_generic_ code will never break down a THP unless a ->pte_entry handler is
actually set.
This means that the ->pmd_entry handlers can now choose to deal with THPs
without breaking them down.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Eric B Munson <emunson@mgebm.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Cc: Michael J Wolf <mjwolf@us.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rotate_reclaimable_page function moves just written out pages, which
the VM wanted to reclaim, to the end of the inactive list. That way the
VM will find those pages first next time it needs to free memory.
This patch applies the rule in memcg. It can help to prevent unnecessary
working page eviction of memcg.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
