| Age | Commit message (Collapse) | Author |
|---|
|
Fix this compilation error seen when CONFIG_TRACING is not enabled:
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_init':
drivers/scsi/qla2xxx/qla_os.c:2854:25: error: implicit declaration of function
'trace_array_get_by_name'; did you mean 'trace_array_set_clr_event'?
[-Werror=implicit-function-declaration]
2854 | qla_trc_array = trace_array_get_by_name("qla2xxx");
| ^~~~~~~~~~~~~~~~~~~~~~~
| trace_array_set_clr_event
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_uninit':
drivers/scsi/qla2xxx/qla_os.c:2869:9: error: implicit declaration of function
'trace_array_put' [-Werror=implicit-function-declaration]
2869 | trace_array_put(qla_trc_array);
| ^~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20220907233308.4153-2-aeasi@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the tty fixes and api additions in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At present, the tps68470.c only supports a single clock consumer when
passing platform data to the clock driver. In some devices multiple
sensors depend on the clock provided by a single TPS68470 and so all
need to be able to acquire the clock. Support passing multiple
consumers as platform data.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use _DMA defined in ACPI spec for translation between
DMA address and CPU address, and implement acpi_arch_dma_setup
for initializing dev->dma_range_map, where acpi_dma_get_range
is called for parsing _DMA.
e.g.
If we have two dma ranges:
cpu address dma address size offset
0x200080000000 0x2080000000 0x400000000 0x1fe000000000
0x400080000000 0x4080000000 0x400000000 0x3fc000000000
_DMA for pci devices should be declared in host bridge as
flowing:
Name (_DMA, ResourceTemplate() {
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x4080000000,
0x447fffffff,
0x3fc000000000,
0x400000000,
,
,
)
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x2080000000,
0x247fffffff,
0x1fe000000000,
0x400000000,
,
,
)
})
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In DT systems configurations, of_dma_get_range() returns struct
bus_dma_region DMA regions; they are used to set-up devices
DMA windows with different offset available for translation between DMA
address and CPU address.
In ACPI systems configuration, acpi_dma_get_range() does not return
DMA regions yet and that precludes setting up the dev->dma_range_map
pointer and therefore DMA regions with multiple offsets.
Update acpi_dma_get_range() to return struct bus_dma_region
DMA regions like of_dma_get_range() does.
After updating acpi_dma_get_range(), acpi_arch_dma_setup() is changed for
ARM64, where the original dma_addr and size are removed as these
arguments are now redundant, and pass 0 and U64_MAX for dma_base
and size of arch_setup_dma_ops; this is a simplification consistent
with what other ACPI architectures also pass to iommu_setup_dma_ops().
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small, and late, serial driver fixes for 6.0-rc7 to
resolve some reported problems.
Included in here are:
- tegra icount accounting fixes, including a framework function that
other drivers will be converted over to using in 6.1-rc1.
- fsl_lpuart reset bugfix
- 8250 omap 485 bugfix
- sifive serial clock bugfix
The last three patches have not shown up in linux-next due to them
being added to my tree only 2 days ago, but they are tiny and
self-contained and the developers say they resolve issues that they
have with 6.0-rc. The other three have been in linux-next for a while
with no reported issues"
* tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sifive: enable clocks for UART when probed
serial: 8250: omap: Use serial8250_em485_supported
serial: fsl_lpuart: Reset prior to registration
serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
serial: Create uart_xmit_advance()
|
|
Add const qualifier to the device_get_match_data() parameter.
Some of the future users may utilize this function without
forcing the type.
All the same, dev_fwnode() may be used with a const qualifier.
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135410.49694-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MTD subsystem API allows interacting with MTD devices (e.g. reading,
writing, handling bad blocks). So far a random driver could get MTD
device only by its name (get_mtd_device_nm()). This change allows
getting them also by a DT node.
This API is required for drivers handling DT defined MTD partitions in a
specific way (e.g. U-Boot (sub)partition with environment variables).
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core") driver-core-next
This merges the driver core changes in 6.0-rc7 into driver-core-next as
they are needed here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is in preparation for adding tmpfile support to fuse, which requires
that the tmpfile creation and opening are done as a single operation.
Replace the 'struct dentry *' argument of i_op->tmpfile with
'struct file *'.
Call finish_open_simple() as the last thing in ->tmpfile() instances (may
be omitted in the error case).
Change d_tmpfile() argument to 'struct file *' as well to make callers more
readable.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Create a helper finish_open_simple() that opens the file with the original
dentry. Handle the error case here as well to simplify callers.
Call this helper right after ->tmpfile() is called.
Next patch will change the tmpfile API and move this call into tmpfile
instances.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
No callers outside of fs/namei.c anymore.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
This helper unifies tmpfile creation with opening.
Existing vfs_tmpfile() callers outside of fs/namei.c will be converted to
using this helper. There are two such callers: cachefile and overlayfs.
The cachefiles code currently uses the open_with_fake_path() helper to open
the tmpfile, presumably to disable accounting of the open file. Overlayfs
uses tmpfile for copy_up, which means these struct file instances will be
short lived, hence it doesn't really matter if they are accounted or not.
Disable accounting in this helper too, which should be okay for both
callers.
Add MAY_OPEN permission checking for consistency. Like for create(2)
read/write permissions are not checked.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
for-6.0 has the following fix for cgroup_get_from_id().
836ac87d ("cgroup: fix cgroup_get_from_id")
which conflicts with the following two commits in for-6.1.
4534dee9 ("cgroup: cgroup: Honor caller's cgroup NS when resolving cgroup id")
fa7e439c ("cgroup: Homogenize cgroup_get_from_id() return value")
While the resolution is straightforward, the code ends up pretty ugly
afterwards. Let's pull for-6.0-fixes into for-6.1 so that the code can be
fixed up there.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There are currently no users of this driver's platform data in the
mainline kernel, so let's drop it.
Newer devices should use DT, ACPI, or static software properties to
describe the hardware.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220920025804.1788667-1-dmitry.torokhov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two tiny driver core fixes for 6.0-rc7 that resolve some
oft-reported problems.
The first is a revert of the "fw_devlink.strict=1" default option that
we keep trying to enable, but we keep finding platforms that this just
breaks everything on. So again, we need it reverted and hopefully it
can be worked on in future releases.
The second is a sysfs file-size bugfix that resolves an issue that
many people are starting to hit as the fix it is fixing also was
backported to stable kernels. The util-linux developers are starting
to get bugreports about sysfs files that contain no data because of
this problem, and this fix which has been in linux-next in the
bitfield tree for a long time, resolves it. I'm submitting it here as
it needs to be merged for 6.0-final, not for 6.1-rc1.
Both of these have been in linux-next with no reported issues, only
reports were that these fixed problems"
* tag 'driver-core-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES
Revert "driver core: Set fw_devlink.strict=1 by default"
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for 6.1
The icc-bwmon driver is expected to support measuring LLCC/DDR bandwidth
on SDM845 and SC7280.
The LLCC driver is extended to provide per-platform register mappings to
the LLCC EDAC driver. The QMI encoder/decoder is updated to allow the
passed qmi_elem_info to be const.
Support for SDM845 is added to the sleep stats driver. Power-domains for
the SM6375 platform is added to RPMPD and the platform is added to
socinfo, together with the PM6125 pmic id.
A couple of of_node reference issues are corrected in the smem state and
smsm drivers.
The Qualcomm SCM driver binding is converted to YAML.
* tag 'qcom-drivers-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (29 commits)
soc: qcom: rpmpd: Add SM6375 support
dt-bindings: power: rpmpd: Add SM6375 power domains
firmware: qcom: scm: remove unused __qcom_scm_init declaration
dt-bindings: power: qcom,rpmpd: drop non-working codeaurora.org emails
soc: qcom: icc-bwmon: force clear counter/irq registers
soc: qcom: icc-bwmon: add support for sc7280 LLCC BWMON
dt-bindings: interconnect: qcom,msm8998-bwmon: Add support for sc7280 BWMONs
soc: qcom: llcc: Pass LLCC version based register offsets to EDAC driver
soc: qcom: llcc: Rename reg_offset structs to reflect LLCC version
soc: qcom: qmi: use const for struct qmi_elem_info
soc: qcom: icc-bwmon: remove redundant ret variable
dt-bindings: soc: qcom: stats: Document SDM845 compatible
soc: qcom: stats: Add SDM845 stats config and compatible
dt-bindings: firmware: document Qualcomm SM6115 SCM
soc: qcom: Make QCOM_RPMPD depend on OF
dt-bindings: firmware: convert Qualcomm SCM binding to the yaml
soc: qcom: socinfo: Add PM6125 ID
soc: qcom: socinfo: Add an ID for SM6375
soc: qcom: smem_state: Add refcounting for the 'state->of_node'
soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
...
Link: https://lore.kernel.org/r/20220921155753.1316308-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
pmic-wrapper:
- add support for mt8188
SVS:
- several driver cleanups
power-domain:
- several cleanups of the dt-bindings and driver
mutex:
- add support to mt6795 disp mutex
- add support for mt8186 mdp3 mutex
* tag 'v6.0-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: Add mmsys func to adapt to dpi output for MT8186
soc: mediatek: mutex: Add support for MT6795 Helio X10 display mutex
dt-bindings: soc: mediatek: Add display mutex support for MT6795
soc: mediatek: mutex: Add mt8186 mutex mod settings for mdp3
dt-bindings: soc: mediatek: Add mdp3 mutex support for mt8186
soc: mediatek: pm-domains: Simplify some error message
soc: mediatek: mtk-svs: Explicitly include bitfield header
soc: mediatek: mtk-svs: Use bitfield access macros where possible
soc: mediatek: mtk-svs: Commonize t-calibration-data fuse array read
dt-bindings: power: mediatek: Update maintainer list
dt-bindings: power: mediatek: Support naming power controller node with unit address
dt-bindings: power: mediatek: Refine multiple level power domain nodes
soc: mediatek: mtk-svs: Use devm variant for dev_pm_opp_of_add_table()
soc: mediatek: mtk-svs: Drop of_match_ptr() for of_match_table
soc: mediatek: mtk-svs: Remove hardcoded irqflags
soc: mediatek: mtk-svs: Switch to platform_get_irq()
dt-bindings: soc: mediatek: pwrap: add compatible for mt8188
soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF
Link: https://lore.kernel.org/r/498fe3e5-a237-121a-d500-fbb0994906cb@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/drivers
sunxi SRAM driver changes:
- minor code refactor
- support for Allwinner D1
* tag 'sunxi-drivers-for-6.1-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: sunxi: sram: Fix debugfs info for A64 SRAM C
soc: sunxi: sram: Fix probe function ordering issues
soc: sunxi: sram: Prevent the driver from being unbound
soc: sunxi: sram: Actually claim SRAM regions
Link: https://lore.kernel.org/r/YyeOthH4y8wy8A8R@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
resctrl_arch_rmid_read() returns a value in chunks, as read from the
hardware. This needs scaling to bytes by mon_scale, as provided by
the architecture code.
Now that resctrl_arch_rmid_read() performs the overflow and corrections
itself, it may as well return a value in bytes directly. This allows
the accesses to the architecture specific 'hw' structure to be removed.
Move the mon_scale conversion into resctrl_arch_rmid_read().
mbm_bw_count() is updated to calculate bandwidth from bytes.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-22-james.morse@arm.com
|
|
resctrl_rmid_realloc_threshold can be set by user-space. The maximum
value is specified by the architecture.
Currently max_threshold_occ_write() reads the maximum value from
boot_cpu_data.x86_cache_size, which is not portable to another
architecture.
Add resctrl_rmid_realloc_limit to describe the maximum size in bytes
that user-space can set the threshold to.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-21-james.morse@arm.com
|
|
resctrl_cqm_threshold is stored in a hardware specific chunk size,
but exposed to user-space as bytes.
This means the filesystem parts of resctrl need to know how the hardware
counts, to convert the user provided byte value to chunks. The interface
between the architecture's resctrl code and the filesystem ought to
treat everything as bytes.
Change the unit of resctrl_cqm_threshold to bytes. resctrl_arch_rmid_read()
still returns its value in chunks, so this needs converting to bytes.
As all the users have been touched, rename the variable to
resctrl_rmid_realloc_threshold, which describes what the value is for.
Neither r->num_rmid nor hw_res->mon_scale are guaranteed to be a power
of 2, so the existing code introduces a rounding error from resctrl's
theoretical fraction of the cache usage. This behaviour is kept as it
ensures the user visible value matches the value read from hardware
when the rmid will be reallocated.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-20-james.morse@arm.com
|
|
resctrl_arch_rmid_read() is intended as the function that an
architecture agnostic resctrl filesystem driver can use to
read a value in bytes from a hardware register. Currently the function
returns the MBM values in chunks directly from hardware.
To convert this to bytes, some correction and overflow calculations
are needed. These depend on the resource and domain structures.
Overflow detection requires the old chunks value. None of this
is available to resctrl_arch_rmid_read(). MPAM requires the
resource and domain structures to find the MMIO device that holds
the registers.
Pass the resource and domain to resctrl_arch_rmid_read(). This makes
rmid_dirty() too big. Instead merge it with its only caller, and the
name is kept as a local variable.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-17-james.morse@arm.com
|
|
__rmid_read() selects the specified eventid and returns the counter
value from the MSR. The error handling is architecture specific, and
handled by the callers, rdtgroup_mondata_show() and __mon_event_count().
Error handling should be handled by architecture specific code, as
a different architecture may have different requirements. MPAM's
counters can report that they are 'not ready', requiring a second
read after a short delay. This should be hidden from resctrl.
Make __rmid_read() the architecture specific function for reading
a counter. Rename it resctrl_arch_rmid_read() and move the error
handling into it.
A read from a counter that hardware supports but resctrl does not
now returns -EINVAL instead of -EIO from the default case in
__mon_event_count(). It isn't possible for user-space to see this
change as resctrl doesn't expose counters it doesn't support.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-16-james.morse@arm.com
|
|
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This documents the possible MLO_PAUSE_* settings which can result from
different combinations of MAC_(A)SYM_PAUSE. Special note is paid to
settings which can result from user configuration (MLO_PAUSE_AN). The
autonegotiation results are more-or-less a direct consequence of IEEE
802.3 Table 28B-2.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To abstract the rmid counters into a helper that returns the number
of bytes counted, architecture specific per-rmid state is needed.
It needs to be possible to reset this hidden state, as the values
may outlive the life of an rmid, or the mount time of the filesystem.
mon_event_read() is called with first = true when an rmid is first
allocated in mkdir_mondata_subdir(). Add resctrl_arch_reset_rmid()
and call it from __mon_event_count()'s rr->first check.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-15-james.morse@arm.com
|
|
kmalloc's API family is critical for mm, with one nature that it will
round up the request size to a fixed one (mostly power of 2). Say
when user requests memory for '2^n + 1' bytes, actually 2^(n+1) bytes
could be allocated, so in worst case, there is around 50% memory
space waste.
The wastage is not a big issue for requests that get allocated/freed
quickly, but may cause problems with objects that have longer life
time.
We've met a kernel boot OOM panic (v5.10), and from the dumped slab
info:
[ 26.062145] kmalloc-2k 814056KB 814056KB
From debug we found there are huge number of 'struct iova_magazine',
whose size is 1032 bytes (1024 + 8), so each allocation will waste
1016 bytes. Though the issue was solved by giving the right (bigger)
size of RAM, it is still nice to optimize the size (either use a
kmalloc friendly size or create a dedicated slab for it).
And from lkml archive, there was another crash kernel OOM case [1]
back in 2019, which seems to be related with the similar slab waste
situation, as the log is similar:
[ 4.332648] iommu: Adding device 0000:20:02.0 to group 16
[ 4.338946] swapper/0 invoked oom-killer: gfp_mask=0x6040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null), order=0, oom_score_adj=0
...
[ 4.857565] kmalloc-2048 59164KB 59164KB
The crash kernel only has 256M memory, and 59M is pretty big here.
(Note: the related code has been changed and optimised in recent
kernel [2], these logs are just picked to demo the problem, also
a patch changing its size to 1024 bytes has been merged)
So add an way to track each kmalloc's memory waste info, and
leverage the existing SLUB debug framework (specifically
SLUB_STORE_USER) to show its call stack of original allocation,
so that user can evaluate the waste situation, identify some hot
spots and optimize accordingly, for a better utilization of memory.
The waste info is integrated into existing interface:
'/sys/kernel/debug/slab/kmalloc-xx/alloc_traces', one example of
'kmalloc-4k' after boot is:
126 ixgbe_alloc_q_vector+0xbe/0x830 [ixgbe] waste=233856/1856 age=280763/281414/282065 pid=1330 cpus=32 nodes=1
__kmem_cache_alloc_node+0x11f/0x4e0
__kmalloc_node+0x4e/0x140
ixgbe_alloc_q_vector+0xbe/0x830 [ixgbe]
ixgbe_init_interrupt_scheme+0x2ae/0xc90 [ixgbe]
ixgbe_probe+0x165f/0x1d20 [ixgbe]
local_pci_probe+0x78/0xc0
work_for_cpu_fn+0x26/0x40
...
which means in 'kmalloc-4k' slab, there are 126 requests of
2240 bytes which got a 4KB space (wasting 1856 bytes each
and 233856 bytes in total), from ixgbe_alloc_q_vector().
And when system starts some real workload like multiple docker
instances, there could are more severe waste.
[1]. https://lkml.org/lkml/2019/8/12/266
[2]. https://lore.kernel.org/lkml/2920df89-9975-5785-f79b-257d3052dfaf@huawei.com/
[Thanks Hyeonggon for pointing out several bugs about sorting/format]
[Thanks Vlastimil for suggesting way to reduce memory usage of
orig_size and keep it only for kmalloc objects]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
protection
Add ifc bits related to advanced steering operations (ASO) and general
object modify for macsec to use as part of offloading EPN and replay
protection features.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix ifc fields name to be consistent with the device spec document.
Fixes: 8385c51ff5bc ("net/mlx5: Introduce MACsec Connect-X offload hardware bits and structures")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of fixes for fixes for the soc tree:
- A fix for the interrupt number on at91/lan966 ethernet PHYs
- A second round of fixes for NXP i.MX series, including a couple of
build issues, and board specific DT corrections on TQMa8MPQL,
imx8mp-venice-gw74xx and imx8mm-verdin for reliability and
partially broken functionality
- Several fixes for Rockchip SoCs, addressing a USB issue on
BPI-R2-Pro, wakeup on Gru-Bob and reliability of high-speed SD
cards, among other minor issues
- A fix for a long-running naming mistake that prevented the moxart
mmc driver from working at all
- Multiple Arm SCMI firmware fixes for hardening some corner cases"
* tag 'soc-fixes-6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
arm64: dts: imx8mp-venice-gw74xx: fix port/phy validation
ARM: dts: lan966x: Fix the interrupt number for internal PHYs
arm64: dts: imx8mp-venice-gw74xx: fix ksz9477 cpu port
arm64: dts: imx8mp-venice-gw74xx: fix CAN STBY polarity
dt-bindings: memory-controllers: fsl,imx8m-ddrc: drop Leonard Crestez
arm64: dts: tqma8mqml: Include phy-imx8-pcie.h header
arm64: defconfig: enable ARCH_NXP
arm64: dts: imx8mp-tqma8mpql-mba8mpxl: add missing pinctrl for RTC alarm
ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
arm64: dts: imx8mm-verdin: extend pmic voltages
arm64: dts: rockchip: Remove 'enable-active-low' from rk3566-quartz64-a
arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
arm64: dts: rockchip: fix property for usb2 phy supply on rk3568-evb1-v10
arm64: dts: rockchip: fix property for usb2 phy supply on rock-3a
arm64: dts: imx8ulp: add #reset-cells for pcc
arm64: dts: tqma8mpxl-ba8mpxl: Fix button GPIOs
arm64: dts: imx8mn: remove GPU power domain reset
arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
arm64: dts: imx8mm: Reverse CPLD_Dn GPIO label mapping on MX8Menlo
arm64: dts: rockchip: fix upper usb port on BPI-R2-Pro
...
|
|
update_mba_bw() calculates a new control value for the MBA resource
based on the user provided mbps_val and the current measured
bandwidth. Some control values need remapping by delay_bw_map().
It does this by calling wrmsrl() directly. This needs splitting
up to be done by an architecture specific helper, so that the
remainder can eventually be moved to /fs/.
Add resctrl_arch_update_one() to apply one configuration value
to the provided resource and domain. This avoids the staging
and cross-calling that is only needed with changes made by
user-space. delay_bw_map() moves to be part of the arch code,
to maintain the 'percentage control' view of MBA resources
in resctrl.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-12-james.morse@arm.com
|
|
To support resctrl's MBA software controller, the architecture must provide
a second configuration array to hold the mbps_val[] from user-space.
This complicates the interface between the architecture specific code and
the filesystem portions of resctrl that will move to /fs/, to allow
multiple architectures to support resctrl.
Make the filesystem parts of resctrl create an array for the mba_sc
values. The software controller can be changed to use this, allowing
the architecture code to only consider the values configured in hardware.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-9-james.morse@arm.com
|
|
Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set
If the IRQ hasn't been set up yet, the UART will have zeroes in its MSI
address/data registers. Disabling the IRQ at the interrupt controller
won't stop the UART from performing a DMA write to the address programmed
in its MSI address register (zero) when it wants to signal an interrupt.
The UARTs (in Ice Lake-D) implement PCI 2.1 style MSI without masking
capability, so there is no way to mask the interrupt at the source PCI
function level, except disabling the MSI capability entirely, but that
would cause it to fall back to INTx# assertion, and the PCI specification
prohibits disabling the MSI capability as a way to mask a function's
interrupt service request.
The MSI address register is zeroed by the hangup as the irq is freed.
The interrupt is signalled during serial8250_do_startup() performing a
THRE test that temporarily toggles THRI in IER. The THRE test currently
occurs before UART's irq (and MSI address) is properly set up.
Refactor serial8250_do_startup() such that irq is set up before the
THRE test. The current irq setup code is intermixed with the timer
setup code. As THRE test must be performed prior to the timer setup,
extract it into own function and call it only after the THRE test.
The ->setup_timer() needs to be part of the struct uart_8250_ops in
order to not create circular dependency between 8250 and 8250_base
modules.
Fixes: 40b36daad0ac ("[PATCH] 8250 UART backup timer")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Lennert Buytenhek <buytenh@arista.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922070005.2965-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use BIT_ULL rather than encoding bits explicitly where applicable with
UART port flags. This makes a (__force upf_t) cast redundant, but keep
it for visual consistency with the flags defined in terms of userspace
macros.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209210007030.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A SERIAL_8250_16550A_VARIANTS configuration option has been recently
defined that lets one request the 8250 driver not to probe for 16550A
device features so as to reduce the driver's device startup time in
virtual machines.
Some actual hardware devices require these features to have been fully
determined however for their driver to work correctly, so define a flag
to let drivers request full 16550A feature probing on a device-by-device
basis if required regardless of the SERIAL_8250_16550A_VARIANTS option
setting chosen.
Fixes: dc56ecb81a0a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable@vger.kernel.org # v5.6+
Reported-by: Anders Blomdell <anders.blomdell@control.lth.se>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209202357520.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to Greg, in the context of magic numbers as defined in
magic-number.rst, "the tty layer should not need this and I'll gladly
take patches"
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Ref: https://lore.kernel.org/linux-doc/YyMlovoskUcHLEb7@kroah.com/
Link: https://lore.kernel.org/r/723478a270a3858f27843cbec621df4d5d44efcc.1663288066.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to Greg, in the context of magic numbers as defined in
magic-number.rst, "the tty layer should not need this and I'll gladly
take patches"
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Ref: https://lore.kernel.org/linux-doc/YyMlovoskUcHLEb7@kroah.com/
Link: https://lore.kernel.org/r/476d024cd6b04160a5de381ea2b9856b60088cbd.1663288066.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Because domains are exposed to user-space via resctrl, the filesystem
must update its state when CPU hotplug callbacks are triggered.
Some of this work is common to any architecture that would support
resctrl, but the work is tied up with the architecture code to
free the memory.
Move the monitor subdir removal and the cancelling of the mbm/limbo
works into a new resctrl_offline_domain() call. These bits are not
specific to the architecture. Grouping them in one function allows
that code to be moved to /fs/ and re-used by another architecture.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-6-james.morse@arm.com
|
|
Because domains are exposed to user-space via resctrl, the filesystem
must update its state when CPU hotplug callbacks are triggered.
Some of this work is common to any architecture that would support
resctrl, but the work is tied up with the architecture code to
allocate the memory.
Move domain_setup_mon_state(), the monitor subdir creation call and the
mbm/limbo workers into a new resctrl_online_domain() call. These bits
are not specific to the architecture. Grouping them in one function
allows that code to be moved to /fs/ and re-used by another architecture.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-4-james.morse@arm.com
|
|
Other than pcie bus, introduce support for axi bus to mtk wed driver.
Axi bus is used to connect mt7986-wmac soc chip available on mt7986
device.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce Wireless Etherne Dispatcher support on transmission side
for mt7986 chipset
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
mon_enabled and mon_capable are always set as a pair by
rdt_get_mon_l3_config().
There is no point having two values.
Merge them together.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-3-james.morse@arm.com
|
