summaryrefslogtreecommitdiff
path: root/include/linux
AgeCommit message (Collapse)Author
2021-10-27PM / wakeirq: support enabling wake-up irq after runtime_suspend calledChunfeng Yun
When the dedicated wake IRQ is level trigger, and it uses the device's low-power status as the wakeup source, that means if the device is not in low-power state, the wake IRQ will be triggered if enabled; For this case, need enable the wake IRQ after running the device's ->runtime_suspend() which make it enter low-power state. e.g. Assume the wake IRQ is a low level trigger type, and the wakeup signal comes from the low-power status of the device. The wakeup signal is low level at running time (0), and becomes high level when the device enters low-power state (runtime_suspend (1) is called), a wakeup event at (2) make the device exit low-power state, then the wakeup signal also becomes low level. ------------------ | ^ ^| ---------------- | | -------------- |<---(0)--->|<--(1)--| (3) (2) (4) if enable the wake IRQ before running runtime_suspend during (0), a wake IRQ will arise, it causes resume immediately; it works if enable wake IRQ ( e.g. at (3) or (4)) after running ->runtime_suspend(). This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to optionally support enabling wake IRQ after running ->runtime_suspend(). Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-10-27bpf: Use u64_stats_t in struct bpf_prog_statsEric Dumazet
Commit 316580b69d0a ("u64_stats: provide u64_stats_t type") fixed possible load/store tearing on 64bit arches. For instance the following C code stats->nsecs += sched_clock() - start; Could be rightfully implemented like this by a compiler, confusing concurrent readers a lot: stats->nsecs += sched_clock(); // arbitrary delay stats->nsecs -= start; Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211026214133.3114279-4-eric.dumazet@gmail.com
2021-10-27bpf: Avoid races in __bpf_prog_run() for 32bit archesEric Dumazet
__bpf_prog_run() can run from non IRQ contexts, meaning it could be re entered if interrupted. This calls for the irq safe variant of u64_stats_update_{begin|end}, or risk a deadlock. This patch is a nop on 64bit arches, fortunately. syzbot report: WARNING: inconsistent lock state 5.12.0-rc3-syzkaller #0 Not tainted -------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. udevd/4013 [HC0[0]:SC0[0]:HE1:SE1] takes: ff7c9dec (&(&pstats->syncp)->seq){+.?.}-{0:0}, at: sk_filter include/linux/filter.h:867 [inline] ff7c9dec (&(&pstats->syncp)->seq){+.?.}-{0:0}, at: do_one_broadcast net/netlink/af_netlink.c:1468 [inline] ff7c9dec (&(&pstats->syncp)->seq){+.?.}-{0:0}, at: netlink_broadcast_filtered+0x27c/0x4fc net/netlink/af_netlink.c:1520 {IN-SOFTIRQ-W} state was registered at: lock_acquire.part.0+0xf0/0x41c kernel/locking/lockdep.c:5510 lock_acquire+0x6c/0x74 kernel/locking/lockdep.c:5483 do_write_seqcount_begin_nested include/linux/seqlock.h:520 [inline] do_write_seqcount_begin include/linux/seqlock.h:545 [inline] u64_stats_update_begin include/linux/u64_stats_sync.h:129 [inline] bpf_prog_run_pin_on_cpu include/linux/filter.h:624 [inline] bpf_prog_run_clear_cb+0x1bc/0x270 include/linux/filter.h:755 run_filter+0xa0/0x17c net/packet/af_packet.c:2031 packet_rcv+0xc0/0x3e0 net/packet/af_packet.c:2104 dev_queue_xmit_nit+0x2bc/0x39c net/core/dev.c:2387 xmit_one net/core/dev.c:3588 [inline] dev_hard_start_xmit+0x94/0x518 net/core/dev.c:3609 sch_direct_xmit+0x11c/0x1f0 net/sched/sch_generic.c:313 qdisc_restart net/sched/sch_generic.c:376 [inline] __qdisc_run+0x194/0x7f8 net/sched/sch_generic.c:384 qdisc_run include/net/pkt_sched.h:136 [inline] qdisc_run include/net/pkt_sched.h:128 [inline] __dev_xmit_skb net/core/dev.c:3795 [inline] __dev_queue_xmit+0x65c/0xf84 net/core/dev.c:4150 dev_queue_xmit+0x14/0x18 net/core/dev.c:4215 neigh_resolve_output net/core/neighbour.c:1491 [inline] neigh_resolve_output+0x170/0x228 net/core/neighbour.c:1471 neigh_output include/net/neighbour.h:510 [inline] ip6_finish_output2+0x2e4/0x9fc net/ipv6/ip6_output.c:117 __ip6_finish_output net/ipv6/ip6_output.c:182 [inline] __ip6_finish_output+0x164/0x3f8 net/ipv6/ip6_output.c:161 ip6_finish_output+0x2c/0xb0 net/ipv6/ip6_output.c:192 NF_HOOK_COND include/linux/netfilter.h:290 [inline] ip6_output+0x74/0x294 net/ipv6/ip6_output.c:215 dst_output include/net/dst.h:448 [inline] NF_HOOK include/linux/netfilter.h:301 [inline] NF_HOOK include/linux/netfilter.h:295 [inline] mld_sendpack+0x2a8/0x7e4 net/ipv6/mcast.c:1679 mld_send_cr net/ipv6/mcast.c:1975 [inline] mld_ifc_timer_expire+0x1e8/0x494 net/ipv6/mcast.c:2474 call_timer_fn+0xd0/0x570 kernel/time/timer.c:1431 expire_timers kernel/time/timer.c:1476 [inline] __run_timers kernel/time/timer.c:1745 [inline] run_timer_softirq+0x2e4/0x384 kernel/time/timer.c:1758 __do_softirq+0x204/0x7ac kernel/softirq.c:345 do_softirq_own_stack include/asm-generic/softirq_stack.h:10 [inline] invoke_softirq kernel/softirq.c:228 [inline] __irq_exit_rcu+0x1d8/0x200 kernel/softirq.c:422 irq_exit+0x10/0x3c kernel/softirq.c:446 __handle_domain_irq+0xb4/0x120 kernel/irq/irqdesc.c:692 handle_domain_irq include/linux/irqdesc.h:176 [inline] gic_handle_irq+0x84/0xac drivers/irqchip/irq-gic.c:370 __irq_svc+0x5c/0x94 arch/arm/kernel/entry-armv.S:205 debug_smp_processor_id+0x0/0x24 lib/smp_processor_id.c:53 rcu_read_lock_held_common kernel/rcu/update.c:108 [inline] rcu_read_lock_sched_held+0x24/0x7c kernel/rcu/update.c:123 trace_lock_acquire+0x24c/0x278 include/trace/events/lock.h:13 lock_acquire+0x3c/0x74 kernel/locking/lockdep.c:5481 rcu_lock_acquire include/linux/rcupdate.h:267 [inline] rcu_read_lock include/linux/rcupdate.h:656 [inline] avc_has_perm_noaudit+0x6c/0x260 security/selinux/avc.c:1150 selinux_inode_permission+0x140/0x220 security/selinux/hooks.c:3141 security_inode_permission+0x44/0x60 security/security.c:1268 inode_permission.part.0+0x5c/0x13c fs/namei.c:521 inode_permission fs/namei.c:494 [inline] may_lookup fs/namei.c:1652 [inline] link_path_walk.part.0+0xd4/0x38c fs/namei.c:2208 link_path_walk fs/namei.c:2189 [inline] path_lookupat+0x3c/0x1b8 fs/namei.c:2419 filename_lookup+0xa8/0x1a4 fs/namei.c:2453 user_path_at_empty+0x74/0x90 fs/namei.c:2733 do_readlinkat+0x5c/0x12c fs/stat.c:417 __do_sys_readlink fs/stat.c:450 [inline] sys_readlink+0x24/0x28 fs/stat.c:447 ret_fast_syscall+0x0/0x2c arch/arm/mm/proc-v7.S:64 0x7eaa4974 irq event stamp: 298277 hardirqs last enabled at (298277): [<802000d0>] no_work_pending+0x4/0x34 hardirqs last disabled at (298276): [<8020c9b8>] do_work_pending+0x9c/0x648 arch/arm/kernel/signal.c:676 softirqs last enabled at (298216): [<8020167c>] __do_softirq+0x584/0x7ac kernel/softirq.c:372 softirqs last disabled at (298201): [<8024dff4>] do_softirq_own_stack include/asm-generic/softirq_stack.h:10 [inline] softirqs last disabled at (298201): [<8024dff4>] invoke_softirq kernel/softirq.c:228 [inline] softirqs last disabled at (298201): [<8024dff4>] __irq_exit_rcu+0x1d8/0x200 kernel/softirq.c:422 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&pstats->syncp)->seq); <Interrupt> lock(&(&pstats->syncp)->seq); *** DEADLOCK *** 1 lock held by udevd/4013: #0: 82b09c5c (rcu_read_lock){....}-{1:2}, at: sk_filter_trim_cap+0x54/0x434 net/core/filter.c:139 stack backtrace: CPU: 1 PID: 4013 Comm: udevd Not tainted 5.12.0-rc3-syzkaller #0 Hardware name: ARM-Versatile Express Backtrace: [<81802550>] (dump_backtrace) from [<818027c4>] (show_stack+0x18/0x1c arch/arm/kernel/traps.c:252) r7:00000080 r6:600d0093 r5:00000000 r4:82b58344 [<818027ac>] (show_stack) from [<81809e98>] (__dump_stack lib/dump_stack.c:79 [inline]) [<818027ac>] (show_stack) from [<81809e98>] (dump_stack+0xb8/0xe8 lib/dump_stack.c:120) [<81809de0>] (dump_stack) from [<81804a00>] (print_usage_bug.part.0+0x228/0x230 kernel/locking/lockdep.c:3806) r7:86bcb768 r6:81a0326c r5:830f96a8 r4:86bcb0c0 [<818047d8>] (print_usage_bug.part.0) from [<802bb1b8>] (print_usage_bug kernel/locking/lockdep.c:3776 [inline]) [<818047d8>] (print_usage_bug.part.0) from [<802bb1b8>] (valid_state kernel/locking/lockdep.c:3818 [inline]) [<818047d8>] (print_usage_bug.part.0) from [<802bb1b8>] (mark_lock_irq kernel/locking/lockdep.c:4021 [inline]) [<818047d8>] (print_usage_bug.part.0) from [<802bb1b8>] (mark_lock.part.0+0xc34/0x136c kernel/locking/lockdep.c:4478) r10:83278fe8 r9:82c6d748 r8:00000000 r7:82c6d2d4 r6:00000004 r5:86bcb768 r4:00000006 [<802ba584>] (mark_lock.part.0) from [<802bc644>] (mark_lock kernel/locking/lockdep.c:4442 [inline]) [<802ba584>] (mark_lock.part.0) from [<802bc644>] (mark_usage kernel/locking/lockdep.c:4391 [inline]) [<802ba584>] (mark_lock.part.0) from [<802bc644>] (__lock_acquire+0x9bc/0x3318 kernel/locking/lockdep.c:4854) r10:86bcb768 r9:86bcb0c0 r8:00000001 r7:00040000 r6:0000075a r5:830f96a8 r4:00000000 [<802bbc88>] (__lock_acquire) from [<802bfb90>] (lock_acquire.part.0+0xf0/0x41c kernel/locking/lockdep.c:5510) r10:00000000 r9:600d0013 r8:00000000 r7:00000000 r6:828a2680 r5:828a2680 r4:861e5bc8 [<802bfaa0>] (lock_acquire.part.0) from [<802bff28>] (lock_acquire+0x6c/0x74 kernel/locking/lockdep.c:5483) r10:8146137c r9:00000000 r8:00000001 r7:00000000 r6:00000000 r5:00000000 r4:ff7c9dec [<802bfebc>] (lock_acquire) from [<81381eb4>] (do_write_seqcount_begin_nested include/linux/seqlock.h:520 [inline]) [<802bfebc>] (lock_acquire) from [<81381eb4>] (do_write_seqcount_begin include/linux/seqlock.h:545 [inline]) [<802bfebc>] (lock_acquire) from [<81381eb4>] (u64_stats_update_begin include/linux/u64_stats_sync.h:129 [inline]) [<802bfebc>] (lock_acquire) from [<81381eb4>] (__bpf_prog_run_save_cb include/linux/filter.h:727 [inline]) [<802bfebc>] (lock_acquire) from [<81381eb4>] (bpf_prog_run_save_cb include/linux/filter.h:741 [inline]) [<802bfebc>] (lock_acquire) from [<81381eb4>] (sk_filter_trim_cap+0x26c/0x434 net/core/filter.c:149) r10:a4095dd0 r9:ff7c9dd0 r8:e44be000 r7:8146137c r6:00000001 r5:8611ba80 r4:00000000 [<81381c48>] (sk_filter_trim_cap) from [<8146137c>] (sk_filter include/linux/filter.h:867 [inline]) [<81381c48>] (sk_filter_trim_cap) from [<8146137c>] (do_one_broadcast net/netlink/af_netlink.c:1468 [inline]) [<81381c48>] (sk_filter_trim_cap) from [<8146137c>] (netlink_broadcast_filtered+0x27c/0x4fc net/netlink/af_netlink.c:1520) r10:00000001 r9:833d6b1c r8:00000000 r7:8572f864 r6:8611ba80 r5:8698d800 r4:8572f800 [<81461100>] (netlink_broadcast_filtered) from [<81463e60>] (netlink_broadcast net/netlink/af_netlink.c:1544 [inline]) [<81461100>] (netlink_broadcast_filtered) from [<81463e60>] (netlink_sendmsg+0x3d0/0x478 net/netlink/af_netlink.c:1925) r10:00000000 r9:00000002 r8:8698d800 r7:000000b7 r6:8611b900 r5:861e5f50 r4:86aa3000 [<81463a90>] (netlink_sendmsg) from [<81321f54>] (sock_sendmsg_nosec net/socket.c:654 [inline]) [<81463a90>] (netlink_sendmsg) from [<81321f54>] (sock_sendmsg+0x3c/0x4c net/socket.c:674) r10:00000000 r9:861e5dd4 r8:00000000 r7:86570000 r6:00000000 r5:86570000 r4:861e5f50 [<81321f18>] (sock_sendmsg) from [<813234d0>] (____sys_sendmsg+0x230/0x29c net/socket.c:2350) r5:00000040 r4:861e5f50 [<813232a0>] (____sys_sendmsg) from [<8132549c>] (___sys_sendmsg+0xac/0xe4 net/socket.c:2404) r10:00000128 r9:861e4000 r8:00000000 r7:00000000 r6:86570000 r5:861e5f50 r4:00000000 [<813253f0>] (___sys_sendmsg) from [<81325684>] (__sys_sendmsg net/socket.c:2433 [inline]) [<813253f0>] (___sys_sendmsg) from [<81325684>] (__do_sys_sendmsg net/socket.c:2442 [inline]) [<813253f0>] (___sys_sendmsg) from [<81325684>] (sys_sendmsg+0x58/0xa0 net/socket.c:2440) r8:80200224 r7:00000128 r6:00000000 r5:7eaa541c r4:86570000 [<8132562c>] (sys_sendmsg) from [<80200060>] (ret_fast_syscall+0x0/0x2c arch/arm/mm/proc-v7.S:64) Exception stack(0x861e5fa8 to 0x861e5ff0) 5fa0: 00000000 00000000 0000000c 7eaa541c 00000000 00000000 5fc0: 00000000 00000000 76fbf840 00000128 00000000 0000008f 7eaa541c 000563f8 5fe0: 00056110 7eaa53e0 00036cec 76c9bf44 r6:76fbf840 r5:00000000 r4:00000000 Fixes: 492ecee892c2 ("bpf: enable program stats") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211026214133.3114279-2-eric.dumazet@gmail.com
2021-10-27tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker togetherRobin H. Johnson
Running endpoint security solutions like Sentinel1 that use perf-based tracing heavily lead to this repeated dump complaining about dockerd. The default value of 2048 is nowhere near not large enough. Using the prior patch "tracing: show size of requested buffer", we get "perf buffer not large enough, wanted 6644, have 6144", after repeated up-sizing (I did 2/4/6/8K). With 8K, the problem doesn't occur at all, so below is the trace for 6K. I'm wondering if this value should be selectable at boot time, but this is a good starting point. ``` ------------[ cut here ]------------ perf buffer not large enough, wanted 6644, have 6144 WARNING: CPU: 1 PID: 4997 at kernel/trace/trace_event_perf.c:402 perf_trace_buf_alloc+0x8c/0xa0 Modules linked in: [..] CPU: 1 PID: 4997 Comm: sh Tainted: G T 5.13.13-x86_64-00039-gb3959163488e #63 Hardware name: LENOVO 20KH002JUS/20KH002JUS, BIOS N23ET66W (1.41 ) 09/02/2019 RIP: 0010:perf_trace_buf_alloc+0x8c/0xa0 Code: 80 3d 43 97 d0 01 00 74 07 31 c0 5b 5d 41 5c c3 ba 00 18 00 00 89 ee 48 c7 c7 00 82 7d 91 c6 05 25 97 d0 01 01 e8 22 ee bc 00 <0f> 0b 31 c0 eb db 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 55 89 RSP: 0018:ffffb922026b7d58 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff9da5ee012000 RCX: 0000000000000027 RDX: ffff9da881657828 RSI: 0000000000000001 RDI: ffff9da881657820 RBP: 00000000000019f4 R08: 0000000000000000 R09: ffffb922026b7b80 R10: ffffb922026b7b78 R11: ffffffff91dda688 R12: 000000000000000f R13: ffff9da5ee012108 R14: ffff9da8816570a0 R15: ffffb922026b7e30 FS: 00007f420db1a080(0000) GS:ffff9da881640000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000060 CR3: 00000002504a8006 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: kprobe_perf_func+0x11e/0x270 ? do_execveat_common.isra.0+0x1/0x1c0 ? do_execveat_common.isra.0+0x5/0x1c0 kprobe_ftrace_handler+0x10e/0x1d0 0xffffffffc03aa0c8 ? do_execveat_common.isra.0+0x1/0x1c0 do_execveat_common.isra.0+0x5/0x1c0 __x64_sys_execve+0x33/0x40 do_syscall_64+0x6b/0xc0 ? do_syscall_64+0x11/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f420dc1db37 Code: ff ff 76 e7 f7 d8 64 41 89 00 eb df 0f 1f 80 00 00 00 00 f7 d8 64 41 89 00 eb dc 0f 1f 84 00 00 00 00 00 b8 3b 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 01 43 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffd4e8b4e38 EFLAGS: 00000246 ORIG_RAX: 000000000000003b RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f420dc1db37 RDX: 0000564338d1e740 RSI: 0000564338d32d50 RDI: 0000564338d28f00 RBP: 0000564338d28f00 R08: 0000564338d32d50 R09: 0000000000000020 R10: 00000000000001b6 R11: 0000000000000246 R12: 0000564338d28f00 R13: 0000564338d32d50 R14: 0000564338d1e740 R15: 0000564338d28c60 ---[ end trace 83ab3e8e16275e49 ]--- ``` Link: https://lkml.kernel.org/r/20210831043723.13481-2-robbat2@gentoo.org Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-27ftrace: disable preemption when recursion locked王贇
As the documentation explained, ftrace_test_recursion_trylock() and ftrace_test_recursion_unlock() were supposed to disable and enable preemption properly, however currently this work is done outside of the function, which could be missing by mistake. And since the internal using of trace_test_and_set_recursion() and trace_clear_recursion() also require preemption disabled, we can just merge the logical. This patch will make sure the preemption has been disabled when trace_test_and_set_recursion() return bit >= 0, and trace_clear_recursion() will enable the preemption if previously enabled. Link: https://lkml.kernel.org/r/13bde807-779c-aa4c-0672-20515ae365ea@linux.alibaba.com CC: Petr Mladek <pmladek@suse.com> Cc: Guo Ren <guoren@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: Helge Deller <deller@gmx.de> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Jisheng Zhang <jszhang@kernel.org> CC: Steven Rostedt <rostedt@goodmis.org> CC: Miroslav Benes <mbenes@suse.cz> Reported-by: Abaci <abaci@linux.alibaba.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com> [ Removed extra line in comment - SDR ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-27dma-buf: Fix pin callback commentGal Pressman
The pin callback does not necessarily have to move the memory to system memory, remove the sentence from the comment. Link: https://lore.kernel.org/r/20211012120903.96933-2-galpress@amazon.com Signed-off-by: Gal Pressman <galpress@amazon.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2021-10-27block: avoid extra iter advance with async iocbPavel Begunkov
Nobody cares about iov iterators state if we return -EIOCBQUEUED, so as the we now have __blkdev_direct_IO_async(), which gets pages only once, we can skip expensive iov_iter_advance(). It's around 1-2% of all CPU spent. Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Link: https://lore.kernel.org/r/a6158edfbfa2ae3bc24aed29a72f035df18fad2f.1635337135.git.asml.silence@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-10-27fanotify: Allow users to request FAN_FS_ERROR eventsGabriel Krisman Bertazi
Wire up the FAN_FS_ERROR event in the fanotify_mark syscall, allowing user space to request the monitoring of FAN_FS_ERROR events. These events are limited to filesystem marks, so check it is the case in the syscall handler. Link: https://lore.kernel.org/r/20211025192746.66445-29-krisman@collabora.com Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fanotify: Pre-allocate pool of error eventsGabriel Krisman Bertazi
Pre-allocate slots for file system errors to have greater chances of succeeding, since error events can happen in GFP_NOFS context. This patch introduces a group-wide mempool of error events, shared by all FAN_FS_ERROR marks in this group. Link: https://lore.kernel.org/r/20211025192746.66445-20-krisman@collabora.com Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Support FS_ERROR event typeGabriel Krisman Bertazi
Expose a new type of fsnotify event for filesystems to report errors for userspace monitoring tools. fanotify will send this type of notification for FAN_FS_ERROR events. This also introduce a helper for generating the new event. Link: https://lore.kernel.org/r/20211025192746.66445-18-krisman@collabora.com Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fanotify: Require fid_mode for any non-fd eventGabriel Krisman Bertazi
Like inode events, FAN_FS_ERROR will require fid mode. Therefore, convert the verification during fanotify_mark(2) to require fid for any non-fd event. This means fid_mode will not only be required for inode events, but for any event that doesn't provide a descriptor. Link: https://lore.kernel.org/r/20211025192746.66445-17-krisman@collabora.com Suggested-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Pass group argument to free_eventGabriel Krisman Bertazi
For group-wide mempool backed events, like FS_ERROR, the free_event callback will need to reference the group's mempool to free the memory. Wire that argument into the current callers. Link: https://lore.kernel.org/r/20211025192746.66445-13-krisman@collabora.com Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Protect fsnotify_handle_inode_event from no-inode eventsGabriel Krisman Bertazi
FAN_FS_ERROR allows events without inodes - i.e. for file system-wide errors. Even though fsnotify_handle_inode_event is not currently used by fanotify, this patch protects other backends from cases where neither inode or dir are provided. Also document the constraints of the interface (inode and dir cannot be both NULL). Link: https://lore.kernel.org/r/20211025192746.66445-12-krisman@collabora.com Suggested-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Retrieve super block from the data fieldGabriel Krisman Bertazi
Some file system events (i.e. FS_ERROR) might not be associated with an inode or directory. For these, we can retrieve the super block from the data field. But, since the super_block is available in the data field on every event type, simplify the code to always retrieve it from there, through a new helper. Link: https://lore.kernel.org/r/20211025192746.66445-11-krisman@collabora.com Suggested-by: Jan Kara <jack@suse.cz> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Add wrapper around fsnotify_add_eventGabriel Krisman Bertazi
fsnotify_add_event is growing in number of parameters, which in most case are just passed a NULL pointer. So, split out a new fsnotify_insert_event function to clean things up for users who don't need an insert hook. Link: https://lore.kernel.org/r/20211025192746.66445-10-krisman@collabora.com Suggested-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: Add helper to detect overflow_eventGabriel Krisman Bertazi
Similarly to fanotify_is_perm_event and friends, provide a helper predicate to say whether a mask is of an overflow event. Link: https://lore.kernel.org/r/20211025192746.66445-9-krisman@collabora.com Suggested-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: clarify contract for create event hooksAmir Goldstein
Clarify argument names and contract for fsnotify_create() and fsnotify_mkdir() to reflect the anomaly of kernfs, which leaves dentries negavite after mkdir/create. Remove the WARN_ON(!inode) in audit code that were added by the Fixes commit under the wrong assumption that dentries cannot be negative after mkdir/create. Fixes: aa93bdc5500c ("fsnotify: use helpers to access data by data_type") Link: https://lore.kernel.org/linux-fsdevel/87mtp5yz0q.fsf@collabora.com/ Link: https://lore.kernel.org/r/20211025192746.66445-4-krisman@collabora.com Reviewed-by: Jan Kara <jack@suse.cz> Reported-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: pass dentry instead of inode dataAmir Goldstein
Define a new data type to pass for event - FSNOTIFY_EVENT_DENTRY. Use it to pass the dentry instead of it's ->d_inode where available. This is needed in preparation to the refactor to retrieve the super block from the data field. In some cases (i.e. mkdir in kernfs), the data inode comes from a negative dentry, such that no super block information would be available. By receiving the dentry itself, instead of the inode, fsnotify can derive the super block even on these cases. Link: https://lore.kernel.org/r/20211025192746.66445-3-krisman@collabora.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Amir Goldstein <amir73il@gmail.com> [Expand explanation in commit message] Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27fsnotify: pass data_type to fsnotify_name()Amir Goldstein
Align the arguments of fsnotify_name() to those of fsnotify(). Link: https://lore.kernel.org/r/20211025192746.66445-2-krisman@collabora.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Signed-off-by: Jan Kara <jack@suse.cz>
2021-10-27x86/boot/compressed: Avoid duplicate malloc() implementationsKees Cook
The early malloc() and free() implementation in include/linux/decompress/mm.h (which is also included by the static decompressors) is static. This is fine when the only thing interested in using malloc() is the decompression code, but the x86 early boot environment may use malloc() in a couple places, leading to a potential collision when the static copies of the available memory region ("malloc_ptr") gets reset to the global "free_mem_ptr" value. As it happened, the existing usage pattern was accidentally safe because each user did 1 malloc() and 1 free() before returning and were not nested: extract_kernel() (misc.c) choose_random_location() (kaslr.c) mem_avoid_init() handle_mem_options() malloc() ... free() ... parse_elf() (misc.c) malloc() ... free() Once the future FGKASLR series is added, however, it will insert additional malloc() calls local to fgkaslr.c in the middle of parse_elf()'s malloc()/free() pair: parse_elf() (misc.c) malloc() if (...) { layout_randomized_image(output, &ehdr, phdrs); malloc() <- boom ... else layout_image(output, &ehdr, phdrs); free() To avoid collisions, there must be a single implementation of malloc(). Adjust include/linux/decompress/mm.h so that visibility can be controlled, provide prototypes in misc.h, and implement the functions in misc.c. This also results in a small size savings: $ size vmlinux.before vmlinux.after text data bss dec hex filename 8842314 468 178320 9021102 89a6ae vmlinux.before 8842240 468 178320 9021028 89a664 vmlinux.after Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20211013175742.1197608-4-keescook@chromium.org
2021-10-27nvme: add new discovery log page entry definitionsHannes Reinecke
TP8014 adds a new SUBTYPE value and a new field EFLAGS for the discovery log page entry. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2021-10-26libata: support concurrent positioning ranges logDamien Le Moal
Add support to discover if an ATA device supports the Concurrent Positioning Ranges data log (address 0x47), indicating that the device is capable of seeking to multiple different locations in parallel using multiple actuators serving different LBA ranges. Also add support to translate the concurrent positioning ranges log into its equivalent Concurrent Positioning Ranges VPD page B9h in libata-scsi.c. The format of the Concurrent Positioning Ranges Log is defined in ACS-5 r9. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Link: https://lore.kernel.org/r/20211027022223.183838-4-damien.lemoal@wdc.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-10-26block: Add independent access ranges supportDamien Le Moal
The Concurrent Positioning Ranges VPD page (for SCSI) and data log page (for ATA) contain parameters describing the set of contiguous LBAs that can be served independently by a single LUN multi-actuator hard-disk. Similarly, a logically defined block device composed of multiple disks can in some cases execute requests directed at different sector ranges in parallel. A dm-linear device aggregating 2 block devices together is an example. This patch implements support for exposing a block device independent access ranges to the user through sysfs to allow optimizing device accesses to increase performance. To describe the set of independent sector ranges of a device (actuators of a multi-actuator HDDs or table entries of a dm-linear device), The type struct blk_independent_access_ranges is introduced. This structure describes the sector ranges using an array of struct blk_independent_access_range structures. This range structure defines the start sector and number of sectors of the access range. The ranges in the array cannot overlap and must contain all sectors within the device capacity. The function disk_set_independent_access_ranges() allows a device driver to signal to the block layer that a device has multiple independent access ranges. In this case, a struct blk_independent_access_ranges is attached to the device request queue by the function disk_set_independent_access_ranges(). The function disk_alloc_independent_access_ranges() is provided for drivers to allocate this structure. struct blk_independent_access_ranges contains kobjects (struct kobject) to expose to the user through sysfs the set of independent access ranges supported by a device. When the device is initialized, sysfs registration of the ranges information is done from blk_register_queue() using the block layer internal function disk_register_independent_access_ranges(). If a driver calls disk_set_independent_access_ranges() for a registered queue, e.g. when a device is revalidated, disk_set_independent_access_ranges() will execute disk_register_independent_access_ranges() to update the sysfs attribute files. The sysfs file structure created starts from the independent_access_ranges sub-directory and contains the start sector and number of sectors of each range, with the information for each range grouped in numbered sub-directories. E.g. for a dual actuator HDD, the user sees: $ tree /sys/block/sdk/queue/independent_access_ranges/ /sys/block/sdk/queue/independent_access_ranges/ |-- 0 | |-- nr_sectors | `-- sector `-- 1 |-- nr_sectors `-- sector For a regular device with a single access range, the independent_access_ranges sysfs directory does not exist. Device revalidation may lead to changes to this structure and to the attribute values. When manipulated, the queue sysfs_lock and sysfs_dir_lock mutexes are held for atomicity, similarly to how the blk-mq and elevator sysfs queue sub-directories are protected. The code related to the management of independent access ranges is added in the new file block/blk-ia-ranges.c. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Link: https://lore.kernel.org/r/20211027022223.183838-2-damien.lemoal@wdc.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-10-26net/mlx5e: Add handle SHAMPO cqe supportKhalid Manaa
This patch adds the new CQE SHAMPO fields: - flush: indicates that we must close the current session and pass the SKB to the network stack. - match: indicates that the current packet matches the oppened session, the packet will be merge into the current SKB. - header_size: the size of the packet headers that written into the headers buffer. - header_entry_index: the entry index in the headers buffer. - data_offset: packets data offset in the WQE. Also new cqe handler is added to handle SHAMPO packets: - The new handler uses CQE SHAMPO fields to build the SKB. CQE's Flush and match fields are not used in this patch, packets are not merged in this patch. Signed-off-by: Khalid Manaa <khalidm@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-26net/mlx5e: Add support to klm_umr_wqeBen Ben-Ishay
This commit adds the needed definitions for using the klm_umr_wqe. UMR stands for user-mode memory registration, is a mechanism to alter address translation properties of MKEY by posting WorkQueueElement aka WQE on send queue. MKEY stands for memory key, MKEY are used to describe a region in memory that can be later used by HW. KLM stands for {Key, Length, MemVa}, KLM_MKEY is indirect MKEY that enables to map multiple memory spaces with different sizes in unified MKEY. klm_umr_wqe is a UMR that use to update a KLM_MKEY. SHAMPO feature uses KLM_MKEY for memory registration of his header buffer. Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-26net/mlx5e: Rename TIR lro functions to TIR packet merge functionsKhalid Manaa
This series introduces new packet merge type, therefore rename lro functions to packet merge to support the new merge type: - Generalize + rename mlx5e_build_tir_ctx_lro to mlx5e_build_tir_ctx_packet_merge. - Rename mlx5e_modify_tirs_lro to mlx5e_modify_tirs_packet_merge. - Rename lro bit in mlx5_ifc_modify_tir_bitmask_bits to packet_merge. - Rename lro_en in mlx5e_params to packet_merge_type type and combine packet_merge params into one struct mlx5e_packet_merge_param. Signed-off-by: Khalid Manaa <khalidm@nvidia.com> Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-26net/mlx5: Add SHAMPO caps, HW bits and enumerationsBen Ben-Ishay
This commit adds SHAMPO bit to hca_cap and SHAMPO capabilities structure, SHAMPO related HW spec hardware fields and enumerations. SHAMPO stands for: split headers and merge payload offload. SHAMPO new fields: WQ: - headers_mkey: mkey that represents the headers buffer, where the packets headers will be written by the HW. - shampo_enable: flag to verify if the WQ supports SHAMPO feature. - log_reservation_size: the log of the reservation size where the data of the packet will be written by the HW. - log_max_num_of_packets_per_reservation: log of the maximum number of packets that can be written to the same reservation. - log_headers_entry_size: log of the header entry size of the headers buffer. - log_headers_buffer_entry_num: log of the entries number of the headers buffer. RQ: - shampo_no_match_alignment_granularity: the HW alignment granularity in case the received packet doesn't match the current session. - shampo_match_criteria_type: the type of match criteria. - reservation_timeout: the maximum time that the HW will hold the reservation. mlx5_ifc_shampo_cap_bits, the capabilities of the SHAMPO feature: - shampo_log_max_reservation_size: the maximum allowed value of the field WQ.log_reservation_size. - log_reservation_size: the minimum allowed value of the field WQ.log_reservation_size. - shampo_min_mss_size: the minimum payload size of packet that can open a new session or be merged to a session. - shampo_max_log_headers_entry_size: the maximum allowed value of the field WQ.log_headers_entry_size Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-26net/mlx5e: Rename lro_timeout to packet_merge_timeoutBen Ben-Ishay
TIR stands for transport interface receive, the TIR object is responsible for performing all transport related operations on the receive side like packet processing, demultiplexing the packets to different RQ's, etc. lro_timeout is a field in the TIR that is used to set the timeout for lro session, this series introduces new packet merge type, therefore rename lro_timeout to packet_merge_timeout for all packet merge types. Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-26lib: bitmap: Introduce node-aware alloc APITariq Toukan
Expose new node-aware API for bitmap allocation: bitmap_alloc_node() / bitmap_zalloc_node(). Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-27gpio: Allow per-parent interrupt dataMarc Zyngier
The core gpiolib code is able to deal with multiple interrupt parents for a single gpio irqchip. It however only allows a single piece of data to be conveyed to all flow handlers (either the gpio_chip or some other, driver-specific data). This means that drivers have to go through some interesting dance to find the correct context, something that isn't great in interrupt context (see aebdc8abc9db86e2bd33070fc2f961012fff74b4 for a prime example). Instead, offer an optional way for a pinctrl/gpio driver to provide an array of pointers which gets used to provide the correct context to the flow handler. Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Joey Gouly <joey.gouly@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20211026175815.52703-2-joey.gouly@arm.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-10-26Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski
Daniel Borkmann says: ==================== pull-request: bpf 2021-10-26 We've added 12 non-merge commits during the last 7 day(s) which contain a total of 23 files changed, 118 insertions(+), 98 deletions(-). The main changes are: 1) Fix potential race window in BPF tail call compatibility check, from Toke Høiland-Jørgensen. 2) Fix memory leak in cgroup fs due to missing cgroup_bpf_offline(), from Quanyang Wang. 3) Fix file descriptor reference counting in generic_map_update_batch(), from Xu Kuohai. 4) Fix bpf_jit_limit knob to the max supported limit by the arch's JIT, from Lorenz Bauer. 5) Fix BPF sockmap ->poll callbacks for UDP and AF_UNIX sockets, from Cong Wang and Yucong Sun. 6) Fix BPF sockmap concurrency issue in TCP on non-blocking sendmsg calls, from Liu Jian. 7) Fix build failure of INODE_STORAGE and TASK_STORAGE maps on !CONFIG_NET, from Tejun Heo. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf: Fix potential race in tail call compatibility check bpf: Move BPF_MAP_TYPE for INODE_STORAGE and TASK_STORAGE outside of CONFIG_NET selftests/bpf: Use recv_timeout() instead of retries net: Implement ->sock_is_readable() for UDP and AF_UNIX skmsg: Extract and reuse sk_msg_is_readable() net: Rename ->stream_memory_read to ->sock_is_readable tcp_bpf: Fix one concurrency problem in the tcp_bpf_send_verdict function cgroup: Fix memory leak caused by missing cgroup_bpf_offline bpf: Fix error usage of map_fd and fdget() in generic_map_update_batch() bpf: Prevent increasing bpf_jit_limit above max bpf: Define bpf_jit_alloc_exec_limit for arm64 JIT bpf: Define bpf_jit_alloc_exec_limit for riscv JIT ==================== Link: https://lore.kernel.org/r/20211026201920.11296-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-26bpf: Fix potential race in tail call compatibility checkToke Høiland-Jørgensen
Lorenzo noticed that the code testing for program type compatibility of tail call maps is potentially racy in that two threads could encounter a map with an unset type simultaneously and both return true even though they are inserting incompatible programs. The race window is quite small, but artificially enlarging it by adding a usleep_range() inside the check in bpf_prog_array_compatible() makes it trivial to trigger from userspace with a program that does, essentially: map_fd = bpf_create_map(BPF_MAP_TYPE_PROG_ARRAY, 4, 4, 2, 0); pid = fork(); if (pid) { key = 0; value = xdp_fd; } else { key = 1; value = tc_fd; } err = bpf_map_update_elem(map_fd, &key, &value, 0); While the race window is small, it has potentially serious ramifications in that triggering it would allow a BPF program to tail call to a program of a different type. So let's get rid of it by protecting the update with a spinlock. The commit in the Fixes tag is the last commit that touches the code in question. v2: - Use a spinlock instead of an atomic variable and cmpxchg() (Alexei) v3: - Put lock and the members it protects into an embedded 'owner' struct (Daniel) Fixes: 3324b584b6f6 ("ebpf: misc core cleanup") Reported-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211026110019.363464-1-toke@redhat.com
2021-10-26bpf: Move BPF_MAP_TYPE for INODE_STORAGE and TASK_STORAGE outside of CONFIG_NETTejun Heo
bpf_types.h has BPF_MAP_TYPE_INODE_STORAGE and BPF_MAP_TYPE_TASK_STORAGE declared inside #ifdef CONFIG_NET although they are built regardless of CONFIG_NET. So, when CONFIG_BPF_SYSCALL && !CONFIG_NET, they are built without the declarations leading to spurious build failures and not registered to bpf_map_types making them unavailable. Fix it by moving the BPF_MAP_TYPE for the two map types outside of CONFIG_NET. Reported-by: kernel test robot <lkp@intel.com> Fixes: a10787e6d58c ("bpf: Enable task local storage for tracing programs") Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/YXG1cuuSJDqHQfRY@slm.duckdns.org
2021-10-26skmsg: Extract and reuse sk_msg_is_readable()Cong Wang
tcp_bpf_sock_is_readable() is pretty much generic, we can extract it and reuse it for non-TCP sockets. Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20211008203306.37525-3-xiyou.wangcong@gmail.com
2021-10-26net/mlx5: remove the recent devlink paramsJakub Kicinski
revert commit 46ae40b94d88 ("net/mlx5: Let user configure io_eq_size param") revert commit a6cb08daa3b4 ("net/mlx5: Let user configure event_eq_size param") revert commit 554604061979 ("net/mlx5: Let user configure max_macs param") The EQE parameters are applicable to more drivers, they should be configured via standard API, probably ethtool. Example of another driver needing something similar: https://lore.kernel.org/all/1633454136-14679-3-git-send-email-sbhatta@marvell.com/ The last param for "max_macs" is probably fine but the documentation is severely lacking. The meaning and implications for changing the param need to be stated. Link: https://lore.kernel.org/r/20211026152939.3125950-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-26fs: export an inode_update_time helperJosef Bacik
If you already have an inode and need to update the time on the inode there is no way to do this properly. Export this helper to allow file systems to update time on the inode so the appropriate handler is called, either ->update_time or generic_update_time. Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2021-10-26Merge tag 'arm-ffa-updates-5.16' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers Arm FF-A updates for v5.16 Just couple of minor updates: - Adding support for MEMORY_LEND API - Handling compatibility with different firmware versions(especially dealing with newer/higher versions than the one supported by the driver) * tag 'arm-ffa-updates-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: firmware: arm_ffa: Remove unused 'compat_version' variable firmware: arm_ffa: Add support for MEM_LEND firmware: arm_ffa: Handle compatibility with different firmware versions firmware: arm_ffa: Fix __ffa_devices_unregister firmware: arm_ffa: Add missing remove callback to ffa_bus_type Link: https://lore.kernel.org/r/20211026141535.1920602-1-sudeep.holla@arm.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-26Merge tag 'samsung-drivers-5.16' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers Samsung SoC drivers changes for v5.16 1. Convert Exynos ChipID and ASV driver to a module and make it a default, instead of selected. The driver is not essential, so it could be disabled, if needed. 2. Add support for Exynos850 and Exynos Auto v9 to Exynos ChipID and ASV driver. 3. Get rid of HAVE_S3C_RTC because it was adding just another layer instead of direct dependencies. 4. Minor cleanups. * tag 'samsung-drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: soc: samsung: exynos-chipid: add exynosautov9 SoC support rtc: s3c: remove HAVE_S3C_RTC in favor of direct dependencies soc: samsung: exynos-chipid: Add Exynos850 support dt-bindings: samsung: exynos-chipid: Document Exynos850 compatible soc: samsung: exynos-chipid: Pass revision reg offsets soc: samsung: pm_domains: drop unused is_off field arm64: exynos: don't have ARCH_EXYNOS select EXYNOS_CHIPID soc: samsung: exynos-chipid: do not enforce built-in soc: samsung: exynos-chipid: convert to a module soc: samsung: exynos-chipid: avoid soc_device_to_device() soc: samsung: exynos-pmu: Fix compilation when nothing selects CONFIG_MFD_CORE Link: https://lore.kernel.org/r/20211026094709.75692-2-krzysztof.kozlowski@canonical.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-26net: phylink: use supported_interfaces for phylink validationRussell King (Oracle)
If the network device supplies a supported interface bitmap, we can use that during phylink's validation to simplify MAC drivers in two ways by using the supported_interfaces bitmap to: 1. reject unsupported interfaces before calling into the MAC driver. 2. generate the set of all supported link modes across all supported interfaces (used mainly for SFP, but also some 10G PHYs.) Suggested-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-26net: phylink: add MAC phy_interface_t bitmapRussell King
Add a phy_interface_t bitmap so the MAC driver can specifiy which PHY interface modes it supports. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-26net: phy: add phy_interface_t bitmap supportRussell King (Oracle)
Add support for a bitmap for phy interface modes, which includes: - a macro to declare the interface bitmap - an inline helper to zero the interface bitmap - an inline helper to detect an empty interface bitmap - inline helpers to do a bitwise AND and OR operations on two interface bitmaps Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-26mctp: Implement extended addressingJeremy Kerr
This change allows an extended address struct - struct sockaddr_mctp_ext - to be passed to sendmsg/recvmsg. This allows userspace to specify output ifindex and physical address information (for sendmsg) or receive the input ifindex/physaddr for incoming messages (for recvmsg). This is typically used by userspace for MCTP address discovery and assignment operations. The extended addressing facility is conditional on a new sockopt: MCTP_OPT_ADDR_EXT; userspace must explicitly enable addressing before the kernel will consume/populate the extended address data. Includes a fix for an uninitialised var: Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-26Merge tag '20210927135559.738-6-srinivas.kandagatla@linaro.org' of ↵Mark Brown
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into v11_20211026_srinivas_kandagatla_asoc_qcom_add_audioreach_support for audioreach support v5.15-rc1 + 20210927135559.738-[23456]-srinivas.kandagatla@linaro.org This immutable branch is based on v5.15-rc1 and contains the following patches extending the existig APR driver to also implement GPR: 20210927135559.738-2-srinivas.kandagatla@linaro.org 20210927135559.738-3-srinivas.kandagatla@linaro.org 20210927135559.738-4-srinivas.kandagatla@linaro.org 20210927135559.738-5-srinivas.kandagatla@linaro.org 20210927135559.738-6-srinivas.kandagatla@linaro.org
2021-10-26Merge tag 'mlx5-updates-2021-10-25' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2021-10-25 Misc updates for mlx5 driver: 1) Misc updates and cleanups: - Don't write directly to netdev->dev_addr, From Jakub Kicinski - Remove unnecessary checks for slow path flag in tc module - Fix unused function warning of mlx5i_flow_type_mask - Bridge, support replacing existing FDB entry 2) Sub Functions, Reduction in memory usage: - Reduce flow counters bulk query buffer size - Implement max_macs devlink parameter - Add devlink vendor params to control Event Queue sizes - Added SF life cycle trace points by Parav/ 3) From Aya, Firmware health buffer reporting improvements - Print health buffer by log level and more missing information - Periodic update of host time to firmware ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-26genirq: Hide irq_cpu_{on,off}line() behind a deprecated optionMarc Zyngier
irq_cpu_{on,off}line() are now only used by the Octeon platform. Make their use conditional on this plaform being enabled, and otherwise hidden away. Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20211021170414.3341522-4-maz@kernel.org
2021-10-26irq: remove handle_domain_{irq,nmi}()Mark Rutland
Now that entry code handles IRQ entry (including setting the IRQ regs) before calling irqchip code, irqchip code can safely call generic_handle_domain_irq(), and there's no functional reason for it to call handle_domain_irq(). Let's cement this split of responsibility and remove handle_domain_irq() entirely, updating irqchip drivers to call generic_handle_domain_irq(). For consistency, handle_domain_nmi() is similarly removed and replaced with a generic_handle_domain_nmi() function which also does not perform any entry logic. Previously handle_domain_{irq,nmi}() had a WARN_ON() which would fire when they were called in an inappropriate context. So that we can identify similar issues going forward, similar WARN_ON_ONCE() logic is added to the generic_handle_*() functions, and comments are updated for clarity and consistency. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de>
2021-10-26signal: Add an optional check for altstack sizeThomas Gleixner
New x86 FPU features will be very large, requiring ~10k of stack in signal handlers. These new features require a new approach called "dynamic features". The kernel currently tries to ensure that altstacks are reasonably sized. Right now, on x86, sys_sigaltstack() requires a size of >=2k. However, that 2k is a constant. Simply raising that 2k requirement to >10k for the new features would break existing apps which have a compiled-in size of 2k. Instead of universally enforcing a larger stack, prohibit a process from using dynamic features without properly-sized altstacks. This must be enforced in two places: * A dynamic feature can not be enabled without an large-enough altstack for each process thread. * Once a dynamic feature is enabled, any request to install a too-small altstack will be rejected The dynamic feature enabling code must examine each thread in a process to ensure that the altstacks are large enough. Add a new lock (sigaltstack_lock()) to ensure that threads can not race and change their altstack after being examined. Add the infrastructure in form of a config option and provide empty stubs for architectures which do not need dynamic altstack size checks. This implementation will be fleshed out for x86 in a future patch called x86/arch_prctl: Add controls for dynamic XSTATE components [dhansen: commit message. ] Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20211021225527.10184-2-chang.seok.bae@intel.com
2021-10-26tpm: fix Atmel TPM crash caused by too frequent queriesHao Wu
The Atmel TPM 1.2 chips crash with error `tpm_try_transmit: send(): error -62` since kernel 4.14. It is observed from the kernel log after running `tpm_sealdata -z`. The error thrown from the command is as follows ``` $ tpm_sealdata -z Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl, code=0087 (135), I/O error ``` The issue was reproduced with the following Atmel TPM chip: ``` $ tpm_version T0 TPM 1.2 Version Info: Chip Version: 1.2.66.1 Spec Level: 2 Errata Revision: 3 TPM Vendor ID: ATML TPM Version: 01010000 Manufacturer Info: 41544d4c ``` The root cause of the issue is due to the TPM calls to msleep() were replaced with usleep_range() [1], which reduces the actual timeout. Via experiments, it is observed that the original msleep(5) actually sleeps for 15ms. Because of a known timeout issue in Atmel TPM 1.2 chip, the shorter timeout than 15ms can cause the error described above. A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further reduced the timeout to less than 1ms. With experiments, the problematic timeout in the latest kernel is the one for `wait_for_tpm_stat`. To fix it, the patch reverts the timeout of `wait_for_tpm_stat` to 15ms for all Atmel TPM 1.2 chips, but leave it untouched for Ateml TPM 2.0 chip, and chips from other vendors. As explained above, the chosen 15ms timeout is the actual timeout before this issue introduced, thus the old value is used here. Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to the existing TPM_TIMEOUT_RANGE_US (300us). The fixed has been tested in the system with the affected Atmel chip with no issues observed after boot up. References: [1] 9f3fc7bcddcb tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers [2] cf151a9a44d5 tpm: reduce tpm polling delay in tpm_tis_core [3] 59f5a6b07f64 tpm: reduce poll sleep time in tpm_transmit() [4] 424eaf910c32 tpm: reduce polling time to usecs for even finer granularity Fixes: 9f3fc7bcddcb ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers") Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/ Signed-off-by: Hao Wu <hao.wu@rubrik.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2021-10-25ipv6: move inet6_sk(sk)->rx_dst_cookie to sk->sk_rx_dst_cookieEric Dumazet
Increase cache locality by moving rx_dst_coookie next to sk->sk_rx_dst This removes one or two cache line misses in IPv6 early demux (TCP/UDP) Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-25fortify: strlen: Avoid shadowing previous localsQian Cai
The __compiletime_strlen() macro expansion will shadow p_size and p_len local variables. No callers currently use any of the shadowed names for their "p" variable, so there are no code generation problems. Add "__" prefixes to variable definitions __compiletime_strlen() to avoid new W=2 warnings: ./include/linux/fortify-string.h: In function 'strnlen': ./include/linux/fortify-string.h:17:9: warning: declaration of 'p_size' shadows a previous local [-Wshadow] 17 | size_t p_size = __builtin_object_size(p, 1); \ | ^~~~~~ ./include/linux/fortify-string.h:77:17: note: in expansion of macro '__compiletime_strlen' 77 | size_t p_len = __compiletime_strlen(p); | ^~~~~~~~~~~~~~~~~~~~ ./include/linux/fortify-string.h:76:9: note: shadowed declaration is here 76 | size_t p_size = __builtin_object_size(p, 1); | ^~~~~~ Signed-off-by: Qian Cai <quic_qiancai@quicinc.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20211025210528.261643-1-quic_qiancai@quicinc.com
generated by cgit (git 2.34.1) at 2025-09-11 18:36:19 +0000