| Age | Commit message (Collapse) | Author |
|---|
|
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the mac address helpers out, eth.c already contains
a bunch of similar helpers.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There are roughly 40 places where netdev->dev_addr is passed
as the destination to a of_get_mac_address() call. Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Note that of_get_mac_address() already assumes the address is
6 bytes long (ETH_ALEN) so use eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Give try_invoke_on_locked_down_task() a saner name and have it return
an int so that the caller might distinguish between different reasons
of failure.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Vasily Gorbik <gor@linux.ibm.com> # on s390
Link: https://lkml.kernel.org/r/20210929152428.649944917@infradead.org
|
|
Add support to wait on multiple futexes. This is the interface
implemented by this syscall:
futex_waitv(struct futex_waitv *waiters, unsigned int nr_futexes,
unsigned int flags, struct timespec *timeout, clockid_t clockid)
struct futex_waitv {
__u64 val;
__u64 uaddr;
__u32 flags;
__u32 __reserved;
};
Given an array of struct futex_waitv, wait on each uaddr. The thread
wakes if a futex_wake() is performed at any uaddr. The syscall returns
immediately if any waiter has *uaddr != val. *timeout is an optional
absolute timeout value for the operation. This syscall supports only
64bit sized timeout structs. The flags argument of the syscall should be
empty, but it can be used for future extensions. Flags for shared
futexes, sizes, etc. should be used on the individual flags of each
waiter.
__reserved is used for explicit padding and should be 0, but it might be
used for future extensions. If the userspace uses 32-bit pointers, it
should make sure to explicitly cast it when assigning to waitv::uaddr.
Returns the array index of one of the woken futexes. There’s no given
information of how many were woken, or any particular attribute of it
(if it’s the first woken, if it is of the smaller index...).
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210923171111.300673-17-andrealmeid@collabora.com
|
|
Put the syscalls in their own little file.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: André Almeida <andrealmeid@collabora.com>
Link: https://lore.kernel.org/r/20210923171111.300673-3-andrealmeid@collabora.com
|
|
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an extended state and sub-state to describe link issues related to
transceiver modules.
The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state
tells user space that port is unable to gain a carrier because the CMIS
Module State Machine did not reach the ModuleReady (Fully Operational)
state. For example, if the module is stuck at ModuleLowPwr or
ModuleFault state. In case of the latter, user space can read the fault
reason from the module's EEPROM and potentially reset it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixup conflicts.
# Conflicts:
# tools/objtool/check.c
|
|
Rename coredump_exit_mm to coredump_task_exit and call it from do_exit
before PTRACE_EVENT_EXIT, and before any cleanup work for a task
happens. This ensures that an accurate copy of the process can be
captured in the coredump as no cleanup for the process happens before
the coredump completes. This also ensures that PTRACE_EVENT_EXIT
will not be visited by any thread until the coredump is complete.
Add a new flag PF_POSTCOREDUMP so that tasks that have passed through
coredump_task_exit can be recognized and ignored in zap_process.
Now that all of the coredumping happens before exit_mm remove code to
test for a coredump in progress from mm_release.
Replace "may_ptrace_stop()" with a simple test of "current->ptrace".
The other tests in may_ptrace_stop all concern avoiding stopping
during a coredump. These tests are no longer necessary as it is now
guaranteed that fatal_signal_pending will be set if the code enters
ptrace_stop during a coredump. The code in ptrace_stop is guaranteed
not to stop if fatal_signal_pending returns true.
Until this change "ptrace_event(PTRACE_EVENT_EXIT)" could call
ptrace_stop without fatal_signal_pending being true, as signals are
dequeued in get_signal before calling do_exit. This is no longer
an issue as "ptrace_event(PTRACE_EVENT_EXIT)" is no longer reached
until after the coredump completes.
Link: https://lkml.kernel.org/r/874kaax26c.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Both arch_ptrace_stop_needed and arch_ptrace_stop are called with an
exit_code and a siginfo structure. Neither argument is used by any of
the implementations so just remove the unneeded arguments.
The two arechitectures that implement arch_ptrace_stop are ia64 and
sparc. Both architectures flush their register stacks before a
ptrace_stack so that all of the register information can be accessed
by debuggers.
As the question of if a register stack needs to be flushed is
independent of why ptrace is stopping not needing arguments make sense.
Cc: David Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Link: https://lkml.kernel.org/r/87lf3mx290.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Abstract the complexity of iterating over all the fences
in a dma_resv object.
The new loop handles the whole RCU and retry dance and
returns only fences where we can be sure we grabbed the
right one.
v2: fix accessing the shared fences while they might be freed,
improve kerneldoc, rename _cursor to _iter, add
dma_resv_iter_is_exclusive, add dma_resv_iter_begin/end
v3: restructor the code, move rcu_read_lock()/unlock() into the
iterator, add dma_resv_iter_is_restarted()
v4: fix NULL deref when no explicit fence exists, drop superflous
rcu_read_lock()/unlock() calls.
v5: fix typos in the documentation
v6: fix coding error when excl fence is NULL
v7: one more logic fix
v8: fix index check in dma_resv_iter_is_exclusive()
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v7)
Link: https://patchwork.freedesktop.org/patch/msgid/20211005113742.1101-2-christian.koenig@amd.com
|
|
This adds selftests that tests the success and failure path for modules
kfuncs (in presence of invalid kfunc calls) for both libbpf and
gen_loader. It also adds a prog_test kfunc_btf_id_list so that we can
add module BTF ID set from bpf_testmod.
This also introduces a couple of test cases to verifier selftests for
validating whether we get an error or not depending on if invalid kfunc
call remains after elimination of unreachable instructions.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211002011757.311265-10-memxor@gmail.com
|
|
This commit moves BTF ID lookup into the newly added registration
helper, in a way that the bbr, cubic, and dctcp implementation set up
their sets in the bpf_tcp_ca kfunc_btf_set list, while the ones not
dependent on modules are looked up from the wrapper function.
This lifts the restriction for them to be compiled as built in objects,
and can be loaded as modules if required. Also modify Makefile.modfinal
to call resolve_btfids for each module.
Note that since kernel kfunc_ids never overlap with module kfunc_ids, we
only match the owner for module btf id sets.
See following commits for background on use of:
CONFIG_X86 ifdef:
569c484f9995 (bpf: Limit static tcp-cc functions in the .BTF_ids list to x86)
CONFIG_DYNAMIC_FTRACE ifdef:
7aae231ac93b (bpf: tcp: Limit calling some tcp cc functions to CONFIG_DYNAMIC_FTRACE)
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211002011757.311265-6-memxor@gmail.com
|
|
This adds helpers for registering btf_id_set from modules and the
bpf_check_mod_kfunc_call callback that can be used to look them up.
With in kernel sets, the way this is supposed to work is, in kernel
callback looks up within the in-kernel kfunc whitelist, and then defers
to the dynamic BTF set lookup if it doesn't find the BTF id. If there is
no in-kernel BTF id set, this callback can be used directly.
Also fix includes for btf.h and bpfptr.h so that they can included in
isolation. This is in preparation for their usage in tcp_bbr, tcp_cubic
and tcp_dctcp modules in the next patch.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211002011757.311265-4-memxor@gmail.com
|
|
This change adds support on the kernel side to allow for BPF programs to
call kernel module functions. Userspace will prepare an array of module
BTF fds that is passed in during BPF_PROG_LOAD using fd_array parameter.
In the kernel, the module BTFs are placed in the auxilliary struct for
bpf_prog, and loaded as needed.
The verifier then uses insn->off to index into the fd_array. insn->off
0 is reserved for vmlinux BTF (for backwards compat), so userspace must
use an fd_array index > 0 for module kfunc support. kfunc_btf_tab is
sorted based on offset in an array, and each offset corresponds to one
descriptor, with a max limit up to 256 such module BTFs.
We also change existing kfunc_tab to distinguish each element based on
imm, off pair as each such call will now be distinct.
Another change is to check_kfunc_call callback, which now include a
struct module * pointer, this is to be used in later patch such that the
kfunc_id and module pointer are matched for dynamically registered BTF
sets from loadable modules, so that same kfunc_id in two modules doesn't
lead to check_kfunc_call succeeding. For the duration of the
check_kfunc_call, the reference to struct module exists, as it returns
the pointer stored in kfunc_btf_tab.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211002011757.311265-2-memxor@gmail.com
|
|
These stubs are needed to allow the tegra-cpuidle driver to be
compile-tested.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Let the governors schedutil, conservative and ondemand to work, if possible
on efficient frequencies only.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This newly introduced flag can be applied by a governor to a CPUFreq
relation, when looking for a frequency within the policy table. The
resolution would then only walk through efficient frequencies.
Even with the flag set, the policy max limit will still be honoured. If no
efficient frequencies can be found within the limits of the policy, an
inefficient one would be returned.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some SoCs such as the sd855 have OPPs within the same policy whose cost is
higher than others with a higher frequency. Those OPPs are inefficients
and it might be interesting for a governor to not use them.
cpufreq_table_set_inefficient() allows the caller to identify a specified
frequency as being inefficient. Inefficient frequencies are only supported
on sorted tables.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The new performance domain flag EM_PERF_DOMAIN_SKIP_INEFFICIENCIES allows
to not take into account inefficient states when estimating energy
consumption. This intends to let the Energy Model know that CPUFreq itself
will skip inefficiencies and such states don't need to be part of the
estimation anymore.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge the current "milliwatts" option into a "flag" field. This intends to
prepare the extension of this structure for inefficient states support in
the Energy Model.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some SoCs, such as the sd855 have OPPs within the same performance domain,
whose cost is higher than others with a higher frequency. Even though
those OPPs are interesting from a cooling perspective, it makes no sense
to use them when the device can run at full capacity. Those OPPs handicap
the performance domain, when choosing the most energy-efficient CPU and
are wasting energy. They are inefficient.
Hence, add support for such OPPs to the Energy Model. The table can now
be read skipping inefficient performance states (and by extension,
inefficient OPPs).
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
mmdrop() is invoked from finish_task_switch() by the incoming task to drop
the mm which was handed over by the previous task. mmdrop() can be quite
expensive which prevents an incoming real-time task from getting useful
work done.
Provide mmdrop_sched() which maps to mmdrop() on !RT kernels. On RT kernels
it delagates the eventually required invocation of __mmdrop() to RCU.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210928122411.648582026@linutronix.de
|
|
Currently in schedstats we have sum_sleep_runtime and iowait_sum, but
there's no metric to show how long the task is in D state. Once a task in
D state, it means the task is blocked in the kernel, for example the
task may be waiting for a mutex. The D state is more frequent than
iowait, and it is more critital than S state. So it is worth to add a
metric to measure it.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210905143547.4668-5-laoar.shao@gmail.com
|
|
If we want to use the schedstats facility to trace other sched classes, we
should make it independent of fair sched class. The struct sched_statistics
is the schedular statistics of a task_struct or a task_group. So we can
move it into struct task_struct and struct task_group to achieve the goal.
After the patch, schestats are orgnized as follows,
struct task_struct {
...
struct sched_entity se;
struct sched_rt_entity rt;
struct sched_dl_entity dl;
...
struct sched_statistics stats;
...
};
Regarding the task group, schedstats is only supported for fair group
sched, and a new struct sched_entity_stats is introduced, suggested by
Peter -
struct sched_entity_stats {
struct sched_entity se;
struct sched_statistics stats;
} __no_randomize_layout;
Then with the se in a task_group, we can easily get the stats.
The sched_statistics members may be frequently modified when schedstats is
enabled, in order to avoid impacting on random data which may in the same
cacheline with them, the struct sched_statistics is defined as cacheline
aligned.
As this patch changes the core struct of scheduler, so I verified the
performance it may impact on the scheduler with 'perf bench sched
pipe', suggested by Mel. Below is the result, in which all the values
are in usecs/op.
Before After
kernel.sched_schedstats=0 5.2~5.4 5.2~5.4
kernel.sched_schedstats=1 5.3~5.5 5.3~5.5
[These data is a little difference with the earlier version, that is
because my old test machine is destroyed so I have to use a new
different test machine.]
Almost no impact on the sched performance.
No functional change.
[lkp@intel.com: reported build failure in earlier version]
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Link: https://lore.kernel.org/r/20210905143547.4668-3-laoar.shao@gmail.com
|
|
/proc/uptime reports idle time by reading the CPUTIME_IDLE field from
the per-cpu kcpustats. However, on NO_HZ systems, idle time is not
continually updated on idle cpus, leading this value to appear
incorrectly small.
/proc/stat performs an accounting update when reading idle time; we
can use the same approach for uptime.
With this patch, /proc/stat and /proc/uptime now agree on idle time.
Additionally, the following shows idle time tick up consistently on an
idle machine:
(while true; do cat /proc/uptime; sleep 1; done) | awk '{print $2-prev; prev=$2}'
Reported-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Josh Don <joshdon@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lkml.kernel.org/r/20210827165438.3280779-1-joshdon@google.com
|
|
Commit 38225f2ef2f4 ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.
This can cause a randconfig build warning that now fails the build
with -Werror:
arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
561 | static struct notifier_block omap_1510_usb_ohci_nb = {
| ^~~~~~~~~~~~~~~~~~~~~
Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
netdev->dev_addr will become const soon. Make sure all
functions which pass it around mark appropriate args
as const.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_u64_to_mac() predates the common helper but doesn't
make the argument constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_mac_to_u64() predates and opencodes ether_addr_to_u64().
It doesn't make the argument constant so it'll be problematic
when dev->dev_addr becomes a const. Convert to the generic helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No users in tree since commit a3498436b3a0 ("netns: restrict uevents"),
so remove this functionality.
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An application has come up that has a device sitting right on the IPMB
that would like to communicate with the BMC on the IPMB using normal
IPMI commands.
Sending these commands and handling the responses is easy enough, no
modifications are needed to the IPMI infrastructure. But if this is an
application that also needs to receive IPMB commands and respond, some
way is needed to handle these incoming commands and send the responses.
Currently, the IPMI message handler only sends commands to the interface
and only receives responses from interface. This change extends the
interface to receive commands/responses and send commands/responses.
These are formatted differently in support of receiving/sending IPMB
messages directly.
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
|
|
It will be needed by the upcoming ipmb direct addressing.
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
|
|
Andrew points out that eth_hw_addr_set() replaces memcpy()
calls so we can't use ether_addr_copy() which assumes
both arguments are 2-bytes aligned.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support programming USB PHY into OTG mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210912181718.1328-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are lots of fields in struct hi6421_spmi_pmic that aren't
used. As a matter of fact, only regmap is needed.
So, drop the struct as a whole, and set regmap as the drvdata.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/1828cb783b1ebca0b98bf0b3077d8701adb228f7.1630586862.git.mchehab+huawei@kernel.org
|
|
ath.git patches for v5.16. Major changes:
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
|
|
Prior to this patch the driver requires two IRQs to function properly,
one required IRQ for control and at least one required IRQ for IO.
This requirement can be relaxed to one as the driver now allows
sharing of IRQs, so control and IO EQs can share the same irq.
This is needed for high scale amount of VFs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Control IRQ is the first IRQ vector. This complicates handling of
completion irqs as we need to offset them by one.
in the next patch, there are scenarios where completion and control EQs
will share the same irq. for example: functions with single IRQ. To ease
such scenarios, we shift control IRQ to the end of the irq array.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
On ingress VLAN push also assign value 0x7FE to reg_c1 tunnel id+opts
bits (tunnel id 0, which is not a valid tunnel id, and option 0x7FE which
was reserved by one of previous patches in the series). In following patch
the reg value is matched on egress miss to restore the packet to its
original state by removing the VLAN before passing it to the software data
path.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Merged due to dependencies in following patches.
Conflict in drivers/infiniband/hw/hfi1/ipoib_tx.c resolved by hand to take
the %p change and txq stats rename together.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Since the openat2(2) syscall uses a struct open_how pointer to communicate
its parameters they are not usefully recorded by the audit SYSCALL record's
four existing arguments.
Add a new audit record type OPENAT2 that reports the parameters in its
third argument, struct open_how with fields oflag, mode and resolve.
The new record in the context of an event would look like:
time->Wed Mar 17 16:28:53 2021
type=PROCTITLE msg=audit(1616012933.531:184): proctitle=
73797363616C6C735F66696C652F6F70656E617432002F746D702F61756469742D
7465737473756974652D737641440066696C652D6F70656E617432
type=PATH msg=audit(1616012933.531:184): item=1 name="file-openat2"
inode=29 dev=00:1f mode=0100600 ouid=0 ogid=0 rdev=00:00
obj=unconfined_u:object_r:user_tmp_t:s0 nametype=CREATE
cap_fp=0 cap_fi=0 cap_fe=0 cap_fver=0 cap_frootid=0
type=PATH msg=audit(1616012933.531:184):
item=0 name="/root/rgb/git/audit-testsuite/tests"
inode=25 dev=00:1f mode=040700 ouid=0 ogid=0 rdev=00:00
obj=unconfined_u:object_r:user_tmp_t:s0 nametype=PARENT
cap_fp=0 cap_fi=0 cap_fe=0 cap_fver=0 cap_frootid=0
type=CWD msg=audit(1616012933.531:184):
cwd="/root/rgb/git/audit-testsuite/tests"
type=OPENAT2 msg=audit(1616012933.531:184):
oflag=0100302 mode=0600 resolve=0xa
type=SYSCALL msg=audit(1616012933.531:184): arch=c000003e syscall=437
success=yes exit=4 a0=3 a1=7ffe315f1c53 a2=7ffe315f1550 a3=18
items=2 ppid=528 pid=540 auid=0 uid=0 gid=0 euid=0 suid=0
fsuid=0 egid=0 sgid=0 fsgid=0 tty=ttyS0 ses=1 comm="openat2"
exe="/root/rgb/git/audit-testsuite/tests/syscalls_file/openat2"
subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023
key="testsuite-1616012933-bjAUcEPO"
Link: https://lore.kernel.org/r/d23fbb89186754487850367224b060e26f9b7181.1621363275.git.rgb@redhat.com
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
[PM: tweak subject, wrap example, move AUDIT_OPENAT2 to 1337]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize 2 MSL timeout value used for the TCP TIME_WAIT state to
non-zero default.
This patch also removes magic number from qedi/qedi_main.c.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update TCP silly-window-syndrome timeout, for the cases where
initiator's small TCP window size prevents FW from transmitting
packets on the connection. Timeout causes FW to retransmit
window probes if needed, preventing I/O stall if initiator ignores
first window probe.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
