| Age | Commit message (Collapse) | Author |
|---|
|
The blackfin architecture is getting removed, so the video
capture driver is also obsolete.
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
It turns out that the struct cec_fh event buffer size of 64 events
(64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's
about 160 ms worth of events and if the Raspberry Pi is busy, then it
might take too long for the application to be scheduled so that it can
drain the pending events. Increase these buffers to 800 events which
is at least 2 seconds worth of events.
There is also a FIFO in between the interrupt and the cec-pin thread.
The thread passes the events on to the CEC core. It is important that
should this FIFO fill up the cec core will be informed that events
have been lost so this can be communicated to the user by setting
CEC_EVENT_FL_DROPPED_EVENTS.
It is very hard to debug CEC problems if events were lost without
informing the user of that fact.
If events were dropped due to the FIFO filling up, then the debugfs
status file will let you know how many events were dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add two new ops (error_inj_show and error_inj_parse_line) to support
error injection functionality for CEC adapters. If both are present,
then the core will add a new error-inj debugfs file that can be used
to see the current error injection commands and to set error injection
commands.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Clearly, changeset 95ce9c28601a ("media: v4l: common: Add a
function to obtain best size from a list") was never tested, as it
broke compilation with:
drivers/media/platform/vivid/vivid-vid-cap.c: In function ‘vivid_try_fmt_vid_cap’:
drivers/media/platform/vivid/vivid-vid-cap.c:565:34: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
mp->width, mp->height);
^
drivers/media/platform/vivid/vivid-vid-cap.c:564:4: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
v4l2_find_nearest_size(webcam_sizes, width, height,
^~~~~~~~~~~~~~~~~~~~~~
__v4l2_find_nearest_size
drivers/media/platform/vivid/vivid-vid-cap.c:564:4: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/i2c/ov5670.c: In function ‘ov5670_set_pad_format’:
drivers/media/i2c/ov5670.c:2233:48: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
fmt->format.width, fmt->format.height);
^
drivers/media/i2c/ov5670.c:2232:9: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
mode = v4l2_find_nearest_size(supported_modes, width, height,
^~~~~~~~~~~~~~~~~~~~~~
__v4l2_find_nearest_size
drivers/media/i2c/ov13858.c: In function ‘ov13858_set_pad_format’:
drivers/media/i2c/ov13858.c:1379:48: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
fmt->format.width, fmt->format.height);
^
drivers/media/i2c/ov13858.c:1378:9: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
mode = v4l2_find_nearest_size(supported_modes, width, height,
^~~~~~~~~~~~~~~~~~~~~~
__v4l2_find_nearest_size
drivers/media/i2c/ov13858.c:1378:9: note: each undeclared identifier is reported only once for each function it appears in
Basically, v4l2_find_nearest_size() callers pass 5 arguments,
while its definition require 6 args.
Unfortunately, my build process was also broken, as it was reporting me that
the compilation went fine:
$ make ARCH=i386 CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y C=1 W=1 CHECK='compile_checks' M=drivers/staging/media
$ make ARCH=i386 CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y C=1 W=1 CHECK='compile_checks' M=drivers/media
*** ERRORS ***
*** WARNINGS ***
compilation succeeded
That was due to a change here to use of linux-log-diff script that
provides a diffstat between the errors output. Somehow, the logic
was missing some fatal errors.
Fixes: 95ce9c28601a ("media: v4l: common: Add a function to obtain best size from a list")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Remove soc_camera framework dependencies from mt9t112 sensor driver.
- Handle clk, gpios and power routines
- Register async subdev
- Remove deprecated g/s_mbus_config operations
- Remove driver flags
- Change driver interface and add kernel doc
- Adjust build system
- Fix code style issues reported by checkpatch in strict mode
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera framework.
As I don't have access to a working camera module, this change has only
been compile tested.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Driver writers can benefit in knowing if/when callbacks are called in
interrupt context. But it is not completely obvious here, so document
it.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
VB2_BUF_STATE_REQUEUEING is accepted by vb2_buffer_done() but not
documented, so add it along with notes about calls in interrupt
context.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Documentation about what start_streaming() should do on failure are
scattered in two places and mostly duplicated, so consolidate them in
one of the two places.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
v4l2_find_nearest_format is not useful for drivers in finding the best
matching format as it assumes a V4L2 specific struct. Drivers will use
v4l2_find_nearest_size instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add a function (as well as a helper macro) to obtain the best size in a
list of device specific sizes. This helps writing drivers as well as
aligns interface behaviour across drivers.
The struct in which this information is contained in is typically specific
to the driver, therefore the existing function v4l2_find_nearest_format()
does not address the need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are several undocumented v4l2-subdev functions that are
part of kAPI. Document them.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
X-Virus-Scanned: Debian amavisd-new at dev.s-opensource.com
media: v4l2-subdev: get rid of __V4L2_SUBDEV_MK_GET_TRY() macro
The __V4L2_SUBDEV_MK_GET_TRY() macro is used to define
3 functions that have the same arguments. The code of those
functions is simple enough to just declare them, de-obfuscating
the code.
While here, replace BUG_ON() by WARN_ON() as there's no reason
why to panic the Kernel if this fails.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Not sure why, but, on ia64, with Linaro's gcc 7.3 compiler,
using #ifdef (CONFIG_I2C) is not OK.
So, replace it by IS_ENABLED(CONFIG_I2C), in order to fix the
builds there.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The dvb_attach()/dvb_detach() methods are ugly hacks designed
to keep using the I2C low-level API. The proper way is to
do I2C bus bindings instead.
Several modules were already converted to use it. Yet,
it is painful to use it, as lots of code need to be
duplicated.
Make it easier by providing two new helper functions:
- dvb_module_probe()
- dvb_module_release()
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
|
|
Remove soc_camera framework dependencies from tw9910 sensor driver.
- Handle clock and gpios
- Register async subdevice
- Remove soc_camera specific g/s_mbus_config operations
- Add kernel doc to driver interface header file
- Adjust build system
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera-based CEU driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Remove soc_camera framework dependencies from ov772x sensor driver.
- Handle clock and gpios
- Register async subdevice
- Remove soc_camera specific g/s_mbus_config operations
- Change image format colorspace from JPEG to SRGB as the two use the
same colorspace information but JPEG makes assumptions on color
components quantization that do not apply to the sensor
- Remove sizes crop from get_selection as driver can't scale
- Add kernel doc to driver interface header file
- Adjust build system
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera-based CEU driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add renesas-ceu header file.
Do not remove the existing sh_mobile_ceu.h one as long as the original
driver does not go away.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
v4l2_fh.h uses the IS_ENABLED() macro and thus should include kconfig.h.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The __v4l2_ctrl_modify_range is the unlocked variant, so the comment about
taking a lock is obviously wrong.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
A recent change to the media_entity_to_video_device() macro breaks some
use-cases for the macro due to a symbol collision. Before the change
this worked:
vdev = media_entity_to_video_device(link->sink->entity);
While after the change it results in a compiler error "error: 'struct
video_device' has no member named 'link'; did you mean 'lock'?". While
the following still works after the change.
struct media_entity *entity = link->sink->entity;
vdev = media_entity_to_video_device(entity);
Fix the collision by renaming the macro argument to '__entity'.
Fixes: 69b925c5fc36d8f1 ("media: v4l2-dev.h: add kernel-doc to two macros")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that we have support for a buffer counter and for
error flags, update them at DMX_DQBUF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Some conditions required for DVB mmap support to work are reversed.
Also, the logic is not too clear.
So, improve the logic, making it easier to be handled.
PS.: I'm pretty sure that I fixed it while testing, but, somehow,
the change got lost.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
CONFIG_DVB_MMAP was misspelled either as CONFIG_DVB_MMSP
or DVB_MMAP, so it had no effect at all. This fixes that,
to make it possible to build it again.
Fixes: 4021053ed52d ("media: dvb-core: make DVB mmap API optional")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add support for the TDA1997x HDMI receivers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix type 'testin' -> 'testing']
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add the v4l2_hdmi_colorimetry() function so we have a single function
that determines the colorspace, YCbCr encoding, quantization range and
transfer function from the InfoFrame data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Create helpers to handle VIDIOC_G/S_PARM by querying the
g/s_frame_interval v4l2_subdev ops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace the old license information with the corresponding SPDX
license for those headers that I authored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
|
|
Add nop variant of media_entity_cleanup. This allows calling
media_entity_cleanup whether or not Media controller is enabled,
simplifying driver code.
Also drop #ifdefs on a few drivers around media_entity_cleanup().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Document the data structures and functions inside this kAPI header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This is currently unused. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that kernel-doc handles nested unions, better document the
match union at struct v4l2_async_subdev.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The V4L2_ASYNC_MATCH_FWNODE match criteria requires just one
struct to be filled (struct fwnode_handle). The V4L2_ASYNC_MATCH_DEVNAME
match criteria requires just a device name.
So, it doesn't make sense to enclose those into structs,
as the criteria can go directly into the union.
That makes easier to document it, as we don't need to document
weird senseless structs.
At drivers, this makes even clearer about the match criteria.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are several macros that aren't documented using kernel-docs
markups.
Document them.
While here, add cross-references to structs on this file.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Remove the V4L2 AS3645A sub-device driver in favour of the LED flash class
driver for the same hardware, drivers/leds/leds-as3645a.c. The latter uses
the V4L2 flash LED class framework to provide V4L2 sub-device interface.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Except for DVB, all media kAPI headers are at include/media.
Move the headers to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
If the subdev is not yet present (probably because the subdev
module has not yet been loaded), the pipe will be NULL. Make sure
that this is not the case before attempting to call the op.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When we split VB2 into an independent streaming module and
a V4L2 one, some vb2-core functions started to have a wrong
description: they're meant to be used only by the API-specific
parts of VB2, like vb2-v4l2, as the functions that V4L2 drivers
should use are all under videobuf2-v4l2.h.
Correct their descriptions.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
