| Age | Commit message (Collapse) | Author |
|---|
|
Allow a policer action to enforce a rate-limit based on packets-per-second,
configurable using a packet-per-second rate and burst parameters.
e.g.
tc filter add dev tap1 parent ffff: u32 match \
u32 0 0 police pkts_rate 3000 pkts_burst 1000
Testing was unable to uncover a performance impact of this change on
existing features.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow flow_offload API to configure packet-per-second policing using rate
and burst parameters.
Dummy implementations of tcf_police_rate_pkt_ps() and
tcf_police_burst_pkt() are supplied which return 0, the unconfigured state.
This is to facilitate splitting the offload, driver, and TC code portion of
this feature into separate patches with the aim of providing a logical flow
for review. And the implementation of these helpers will be filled out by a
follow-up patch.
Signed-off-by: Xingfeng Hu <xingfeng.hu@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defined a new struct mptcp_rm_list, the ids field was an
array of the removing address ids, the nr field was the valid number of
removing address ids in the array. The array size was definced as a new
macro MPTCP_RM_IDS_MAX. Changed the member rm_id of struct
mptcp_out_options to rm_list.
In mptcp_established_options_rm_addr, invoked mptcp_pm_rm_addr_signal to
get the rm_list. According the number of addresses in it, calculated
the padded RM_ADDR suboption length. And saved the ids array in struct
mptcp_out_options's rm_list member.
In mptcp_write_options, iterated each address id from struct
mptcp_out_options's rm_list member, set the invalid ones as TCPOPT_NOP,
then filled them into the RM_ADDR suboption.
Changed TCPOLEN_MPTCP_RM_ADDR_BASE from 4 to 3.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "backlog" argument in listen() specifies
the maximom length of pending connections,
so the accept queue should be considered full
if there are exactly "backlog" elements.
Signed-off-by: liuyacan <yacanliu@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel periodically checks the idle time of nexthop buckets to
determine if they are idle and can be re-populated with a new nexthop.
When the resilient nexthop group is offloaded to hardware, the kernel
will not see activity on nexthop buckets unless it is reported from
hardware.
Add a function that can be periodically called by device drivers to
report activity on nexthop buckets after querying it from the underlying
device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function that can be called by device drivers to set "offload" or
"trap" indication on nexthop buckets following nexthop notifications and
other changes such as a neighbour becoming invalid.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add data structures that will be used for in-kernel notifications about
addition / deletion of a resilient nexthop group and about changes to a
hash bucket within a resilient group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At this moment, there is only one type of next-hop group: an mpath group,
which implements the hash-threshold algorithm.
To select a next hop, hash-threshold algorithm first assigns a range of
hashes to each next hop in the group, and then selects the next hop by
comparing the SKB hash with the individual ranges. When a next hop is
removed from the group, the ranges are recomputed, which leads to
reassignment of parts of hash space from one next hop to another. While
there will usually be some overlap between the previous and the new
distribution, some traffic flows change the next hop that they resolve to.
That causes problems e.g. as established TCP connections are reset, because
the traffic is forwarded to a server that is not familiar with the
connection.
Resilient hashing is a technique to address the above problem. Resilient
next-hop group has another layer of indirection between the group itself
and its constituent next hops: a hash table. The selection algorithm uses a
straightforward modulo operation to choose a hash bucket, and then reads
the next hop that this bucket contains, and forwards traffic there.
This indirection brings an important feature. In the hash-threshold
algorithm, the range of hashes associated with a next hop must be
continuous. With a hash table, mapping between the hash table buckets and
the individual next hops is arbitrary. Therefore when a next hop is deleted
the buckets that held it are simply reassigned to other next hops. When
weights of next hops in a group are altered, it may be possible to choose a
subset of buckets that are currently not used for forwarding traffic, and
use those to satisfy the new next-hop distribution demands, keeping the
"busy" buckets intact. This way, established flows are ideally kept being
forwarded to the same endpoints through the same paths as before the
next-hop group change.
In a nutshell, the algorithm works as follows. Each next hop has a number
of buckets that it wants to have, according to its weight and the number of
buckets in the hash table. In case of an event that might cause bucket
allocation change, the numbers for individual next hops are updated,
similarly to how ranges are updated for mpath group next hops. Following
that, a new "upkeep" algorithm runs, and for idle buckets that belong to a
next hop that is currently occupying more buckets than it wants (it is
"overweight"), it migrates the buckets to one of the next hops that has
fewer buckets than it wants (it is "underweight"). If, after this, there
are still underweight next hops, another upkeep run is scheduled to a
future time.
Chances are there are not enough "idle" buckets to satisfy the new demands.
The algorithm has knobs to select both what it means for a bucket to be
idle, and for whether and when to forcefully migrate buckets if there keeps
being an insufficient number of idle buckets.
There are three users of the resilient data structures.
- The forwarding code accesses them under RCU, and does not modify them
except for updating the time a selected bucket was last used.
- Netlink code, running under RTNL, which may modify the data.
- The delayed upkeep code, which may modify the data. This runs unlocked,
and mutual exclusion between the RTNL code and the delayed upkeep is
maintained by canceling the delayed work synchronously before the RTNL
code touches anything. Later it restarts the delayed work if necessary.
The RTNL code has to implement next-hop group replacement, next hop
removal, etc. For removal, the mpath code uses a neat trick of having a
backup next hop group structure, doing the necessary changes offline, and
then RCU-swapping them in. However, the hash tables for resilient hashing
are about an order of magnitude larger than the groups themselves (the size
might be e.g. 4K entries), and it was felt that keeping two of them is an
overkill. Both the primary next-hop group and the spare therefore use the
same resilient table, and writers are careful to keep all references valid
for the forwarding code. The hash table references next-hop group entries
from the next-hop group that is currently in the primary role (i.e. not
spare). During the transition from primary to spare, the table references a
mix of both the primary group and the spare. When a next hop is deleted,
the corresponding buckets are not set to NULL, but instead marked as empty,
so that the pointer is valid and can be used by the forwarding code. The
buckets are then migrated to a new next-hop group entry during upkeep. The
only times that the hash table is invalid is the very beginning and very
end of its lifetime. Between those points, it is always kept valid.
This patch introduces the core support code itself. It does not handle
notifications towards drivers, which are kept as if the group were an mpath
one. It does not handle netlink either. The only bit currently exposed to
user space is the new next-hop group type, and that is currently bounced.
There is therefore no way to actually access this code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of resilient nexthop groups, there will be two types
of multipath groups: the current hash-threshold "mpath" ones, and resilient
groups. Both are multipath, but to determine the fact, the system needs to
consider two flags. This might prove costly in the datapath. Therefore,
introduce a new flag, that should be set for next-hop groups that have more
than one nexthop, and should be considered multipath.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As specified in IETF RFC 8754, section 4.3.1.2, if the upper layer
header is IPv4 or IPv6, perform IPv6 decapsulation and resubmit the
decapsulated packet to the IPv4 or IPv6 module.
Only IPv6 decapsulation was implemented. This patch adds support for IPv4
decapsulation.
Link: https://tools.ietf.org/html/rfc8754#section-4.3.1.2
Signed-off-by: Julien Massonneau <julien.massonneau@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
iproute2 package is well behaved, but malicious user space can
provide illegal shift values and trigger UBSAN reports.
Add stab parameter to red_check_params() to validate user input.
syzbot reported:
UBSAN: shift-out-of-bounds in ./include/net/red.h:312:18
shift exponent 111 is too large for 64-bit type 'long unsigned int'
CPU: 1 PID: 14662 Comm: syz-executor.3 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
red_calc_qavg_from_idle_time include/net/red.h:312 [inline]
red_calc_qavg include/net/red.h:353 [inline]
choke_enqueue.cold+0x18/0x3dd net/sched/sch_choke.c:221
__dev_xmit_skb net/core/dev.c:3837 [inline]
__dev_queue_xmit+0x1943/0x2e00 net/core/dev.c:4150
neigh_hh_output include/net/neighbour.h:499 [inline]
neigh_output include/net/neighbour.h:508 [inline]
ip6_finish_output2+0x911/0x1700 net/ipv6/ip6_output.c:117
__ip6_finish_output net/ipv6/ip6_output.c:182 [inline]
__ip6_finish_output+0x4c1/0xe10 net/ipv6/ip6_output.c:161
ip6_finish_output+0x35/0x200 net/ipv6/ip6_output.c:192
NF_HOOK_COND include/linux/netfilter.h:290 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:215
dst_output include/net/dst.h:448 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
NF_HOOK include/linux/netfilter.h:295 [inline]
ip6_xmit+0x127e/0x1eb0 net/ipv6/ip6_output.c:320
inet6_csk_xmit+0x358/0x630 net/ipv6/inet6_connection_sock.c:135
dccp_transmit_skb+0x973/0x12c0 net/dccp/output.c:138
dccp_send_reset+0x21b/0x2b0 net/dccp/output.c:535
dccp_finish_passive_close net/dccp/proto.c:123 [inline]
dccp_finish_passive_close+0xed/0x140 net/dccp/proto.c:118
dccp_terminate_connection net/dccp/proto.c:958 [inline]
dccp_close+0xb3c/0xe60 net/dccp/proto.c:1028
inet_release+0x12e/0x280 net/ipv4/af_inet.c:431
inet6_release+0x4c/0x70 net/ipv6/af_inet6.c:478
__sock_release+0xcd/0x280 net/socket.c:599
sock_close+0x18/0x20 net/socket.c:1258
__fput+0x288/0x920 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:140
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
Fixes: 8afa10cbe281 ("net_sched: red: Avoid illegal values")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in commit 29d98f54a4fe ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.
Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzbot reported the suspecious RCU usage in nexthop_fib6_nh() when
called from ipv6_route_seq_show(). The reason is ipv6_route_seq_start()
calls rcu_read_lock_bh(), while nexthop_fib6_nh() calls
rcu_dereference_rtnl().
The fix proposed is to add a variant of nexthop_fib6_nh() to use
rcu_dereference_bh_rtnl() for ipv6_route_seq_show().
The reported trace is as follows:
./include/net/nexthop.h:416 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by syz-executor.0/17895:
at: seq_read+0x71/0x12a0 fs/seq_file.c:169
at: seq_file_net include/linux/seq_file_net.h:19 [inline]
at: ipv6_route_seq_start+0xaf/0x300 net/ipv6/ip6_fib.c:2616
stack backtrace:
CPU: 1 PID: 17895 Comm: syz-executor.0 Not tainted 4.15.0-syzkaller #0
Call Trace:
[<ffffffff849edf9e>] __dump_stack lib/dump_stack.c:17 [inline]
[<ffffffff849edf9e>] dump_stack+0xd8/0x147 lib/dump_stack.c:53
[<ffffffff8480b7fa>] lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5745
[<ffffffff8459ada6>] nexthop_fib6_nh include/net/nexthop.h:416 [inline]
[<ffffffff8459ada6>] ipv6_route_native_seq_show net/ipv6/ip6_fib.c:2488 [inline]
[<ffffffff8459ada6>] ipv6_route_seq_show+0x436/0x7a0 net/ipv6/ip6_fib.c:2673
[<ffffffff81c556df>] seq_read+0xccf/0x12a0 fs/seq_file.c:276
[<ffffffff81dbc62c>] proc_reg_read+0x10c/0x1d0 fs/proc/inode.c:231
[<ffffffff81bc28ae>] do_loop_readv_writev fs/read_write.c:714 [inline]
[<ffffffff81bc28ae>] do_loop_readv_writev fs/read_write.c:701 [inline]
[<ffffffff81bc28ae>] do_iter_read+0x49e/0x660 fs/read_write.c:935
[<ffffffff81bc81ab>] vfs_readv+0xfb/0x170 fs/read_write.c:997
[<ffffffff81c88847>] kernel_readv fs/splice.c:361 [inline]
[<ffffffff81c88847>] default_file_splice_read+0x487/0x9c0 fs/splice.c:416
[<ffffffff81c86189>] do_splice_to+0x129/0x190 fs/splice.c:879
[<ffffffff81c86f66>] splice_direct_to_actor+0x256/0x890 fs/splice.c:951
[<ffffffff81c8777d>] do_splice_direct+0x1dd/0x2b0 fs/splice.c:1060
[<ffffffff81bc4747>] do_sendfile+0x597/0xce0 fs/read_write.c:1459
[<ffffffff81bca205>] SYSC_sendfile64 fs/read_write.c:1520 [inline]
[<ffffffff81bca205>] SyS_sendfile64+0x155/0x170 fs/read_write.c:1506
[<ffffffff81015fcf>] do_syscall_64+0x1ff/0x310 arch/x86/entry/common.c:305
[<ffffffff84a00076>] entry_SYSCALL_64_after_hwframe+0x42/0xb7
Fixes: f88d8ea67fbdb ("ipv6: Plumb support for nexthop object in a fib6_info")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Petr Machata <petrm@nvidia.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move generic blackhole dst ops to the core and use them from both
ipv4_dst_blackhole_ops and ip6_dst_blackhole_ops where possible. No
functional change otherwise. We need these also in other locations
and having to define them over and over again is not great.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is noone setting nci_uart_ops::recv_buf, so the default one
(nci_uart_default_recv_buf) is always used. So drop this hook, move
nci_uart_default_recv_buf before the use in nci_uart_tty_receive and
remove unused parameter flags.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-09
The following pull-request contains BPF updates for your *net-next* tree.
We've added 90 non-merge commits during the last 17 day(s) which contain
a total of 114 files changed, 5158 insertions(+), 1288 deletions(-).
The main changes are:
1) Faster bpf_redirect_map(), from Björn.
2) skmsg cleanup, from Cong.
3) Support for floating point types in BTF, from Ilya.
4) Documentation for sys_bpf commands, from Joe.
5) Support for sk_lookup in bpf_prog_test_run, form Lorenz.
6) Enable task local storage for tracing programs, from Song.
7) bpf_for_each_map_elem() helper, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the bpf_redirect_map() implementation dispatches to the
correct map-lookup function via a switch-statement. To avoid the
dispatching, this change adds bpf_redirect_map() as a map
operation. Each map provides its bpf_redirect_map() version, and
correct function is automatically selected by the BPF verifier.
A nice side-effect of the code movement is that the map lookup
functions are now local to the map implementation files, which removes
one additional function call.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210308112907.559576-2-bjorn.topel@gmail.com
|
|
An issue was found, where if a bluetooth client requests a broadcast
advertisement with scan response data, it will not be properly
registered with the controller. This is because at the time that the
hci_cp_le_set_scan_param structure is created, the scan response will
not yet have been received since it comes in a second MGMT call. With
empty scan response, the request defaults to a non-scannable PDU type.
On some controllers, the subsequent scan response request will fail due
to incorrect PDU type, and others will succeed and not use the scan
response.
This fix allows the advertising parameters MGMT call to include a flag
to let the kernel know whether a scan response will be coming, so that
the correct PDU type is used in the first place. A bluetoothd change is
also incoming to take advantage of it.
To test this, I created a broadcast advertisement with scan response
data and registered it on the hatch chromebook. Without this change, the
request fails, and with it will succeed.
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During suspend, there are a few scan enable and set event filter
commands that don't need to be sent unless there are actual BR/EDR
devices capable of waking the system. Check the HCI_PSCAN bit before
writing scan enable and use a new dev flag, HCI_EVENT_FILTER_CONFIGURED
to control whether to clear the event filter.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
A situation can occur where the interface bound to the sk is different
to the interface bound to the sk attached to the skb. The interface
bound to the sk is the correct one however this information is lost inside
xfrm_output2 and instead the sk on the skb is used in xfrm_output_resume
instead. This assumes that the sk bound interface and the bound interface
attached to the sk within the skb are the same which can lead to lookup
failures inside ip_route_me_harder resulting in the packet being dropped.
We have an l2tp v3 tunnel with ipsec protection. The tunnel is in the
global VRF however we have an encapsulated dot1q tunnel interface that
is within a different VRF. We also have a mangle rule that marks the
packets causing them to be processed inside ip_route_me_harder.
Prior to commit 31c70d5956fc ("l2tp: keep original skb ownership") this
worked fine as the sk attached to the skb was changed from the dot1q
encapsulated interface to the sk for the tunnel which meant the interface
bound to the sk and the interface bound to the skb were identical.
Commit 46d6c5ae953c ("netfilter: use actual socket sk rather than skb sk
when routing harder") fixed some of these issues however a similar
problem existed in the xfrm code.
Fixes: 31c70d5956fc ("l2tp: keep original skb ownership")
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Currently TCP_SKB_CB() is hard-coded in skmsg code, it certainly
does not work for any other non-TCP protocols. We can move them to
skb ext, but it introduces a memory allocation on fast path.
Fortunately, we only need to a word-size to store all the information,
because the flags actually only contains 1 bit so can be just packed
into the lowest bit of the "pointer", which is stored as unsigned
long.
Inside struct sk_buff, '_skb_refdst' can be reused because skb dst is
no longer needed after ->sk_data_ready() so we can just drop it.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210223184934.6054-5-xiyou.wangcong@gmail.com
|
|
Currently, we compute ->data_end with a compile-time constant
offset of skb. But as Jakub pointed out, we can actually compute
it in eBPF JIT code at run-time, so that we can competely get
rid of ->data_end. This is similar to skb_shinfo(skb) computation
in bpf_convert_shinfo_access().
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210223184934.6054-4-xiyou.wangcong@gmail.com
|
|
As suggested by John, clean up sockmap related Kconfigs:
Reduce the scope of CONFIG_BPF_STREAM_PARSER down to TCP stream
parser, to reflect its name.
Make the rest sockmap code simply depend on CONFIG_BPF_SYSCALL
and CONFIG_INET, the latter is still needed at this point because
of TCP/UDP proto update. And leave CONFIG_NET_SOCK_MSG untouched,
as it is used by non-sockmap cases.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210223184934.6054-2-xiyou.wangcong@gmail.com
|
|
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2cac ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add two helper functions to release one table and hooks from
the netns and netlink event path.
2) Add table ownership infrastructure, this new infrastructure allows
users to bind a table (and its content) to a process through the
netlink socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When police action is created by cls API tcf_exts_validate() first
conditional that calls tcf_action_init_1() directly, the action idr is not
updated according to latest changes in action API that require caller to
commit newly created action to idr with tcf_idr_insert_many(). This results
such action not being accessible through act API and causes crash reported
by syzbot:
==================================================================
BUG: KASAN: null-ptr-deref in instrument_atomic_read include/linux/instrumented.h:71 [inline]
BUG: KASAN: null-ptr-deref in atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
BUG: KASAN: null-ptr-deref in __tcf_idr_release net/sched/act_api.c:178 [inline]
BUG: KASAN: null-ptr-deref in tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
Read of size 4 at addr 0000000000000010 by task kworker/u4:5/204
CPU: 0 PID: 204 Comm: kworker/u4:5 Not tainted 5.11.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
__kasan_report mm/kasan/report.c:400 [inline]
kasan_report.cold+0x5f/0xd5 mm/kasan/report.c:413
check_memory_region_inline mm/kasan/generic.c:179 [inline]
check_memory_region+0x13d/0x180 mm/kasan/generic.c:185
instrument_atomic_read include/linux/instrumented.h:71 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
__tcf_idr_release net/sched/act_api.c:178 [inline]
tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
tc_action_net_exit include/net/act_api.h:151 [inline]
police_exit_net+0x168/0x360 net/sched/act_police.c:390
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:190
cleanup_net+0x4ea/0xb10 net/core/net_namespace.c:604
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
worker_thread+0x64c/0x1120 kernel/workqueue.c:2421
kthread+0x3b1/0x4a0 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:296
==================================================================
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 204 Comm: kworker/u4:5 Tainted: G B 5.11.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
panic+0x306/0x73d kernel/panic.c:231
end_report+0x58/0x5e mm/kasan/report.c:100
__kasan_report mm/kasan/report.c:403 [inline]
kasan_report.cold+0x67/0xd5 mm/kasan/report.c:413
check_memory_region_inline mm/kasan/generic.c:179 [inline]
check_memory_region+0x13d/0x180 mm/kasan/generic.c:185
instrument_atomic_read include/linux/instrumented.h:71 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
__tcf_idr_release net/sched/act_api.c:178 [inline]
tcf_idrinfo_destroy+0x129/0x1d0 net/sched/act_api.c:598
tc_action_net_exit include/net/act_api.h:151 [inline]
police_exit_net+0x168/0x360 net/sched/act_police.c:390
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:190
cleanup_net+0x4ea/0xb10 net/core/net_namespace.c:604
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
worker_thread+0x64c/0x1120 kernel/workqueue.c:2421
kthread+0x3b1/0x4a0 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:296
Kernel Offset: disabled
Fix the issue by calling tcf_idr_insert_many() after successful action
initialization.
Fixes: 0fedc63fadf0 ("net_sched: commit action insertions together")
Reported-by: syzbot+151e3e714d34ae4ce7e8@syzkaller.appspotmail.com
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading MRP in HW. Currently implement the switchdev
calls 'SWITCHDEV_OBJ_ID_MRP', 'SWITCHDEV_OBJ_ID_RING_ROLE_MRP',
to allow to create MRP instances and to set the role of these instances.
Add DSA_NOTIFIER_MRP_ADD/DEL and DSA_NOTIFIER_MRP_ADD/DEL_RING_ROLE
which calls to .port_mrp_add/del and .port_mrp_add/del_ring_role in the
DSA driver for the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the member sw_backup to the structures switchdev_obj_ring_role_mrp
and switchdev_obj_in_role_mrp. In this way the SW can call the driver in
2 ways, once when sw_backup is set to false, meaning that the driver
should implement this completely in HW. And if that is not supported the
SW will call again but with sw_backup set to true, meaning that the
HW should help or allow the SW to run the protocol.
For example when role is MRM, if the HW can't detect when it stops
receiving MRP Test frames but it can trap these frames to CPU, then it
needs to return -EOPNOTSUPP when sw_backup is false and return 0 when
sw_backup is true.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will
simplify the code implements MRP callbacks and will be similar with the
vlan filtering.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-02-16
The following pull-request contains BPF updates for your *net-next* tree.
There's a small merge conflict between 7eeba1706eba ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f8161 ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:
[...]
lock_sock(sk);
err = tcp_zerocopy_receive(sk, &zc, &tss);
err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
&zc, &len, err);
release_sock(sk);
[...]
We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).
The main changes are:
1) Adds support of pointers to types with known size among global function
args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.
2) Add bpf_iter for task_vma which can be used to generate information similar
to /proc/pid/maps, from Song Liu.
3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
rewriting bind user ports from BPF side below the ip_unprivileged_port_start
range, both from Stanislav Fomichev.
4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
as well as per-cpu maps for the latter, from Alexei Starovoitov.
5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
for sleepable programs, both from KP Singh.
6) Extend verifier to enable variable offset read/write access to the BPF
program stack, from Andrei Matei.
7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
query device MTU from programs, from Jesper Dangaard Brouer.
8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
tracing programs, from Florent Revest.
9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
otherwise too many passes are required, from Gary Lin.
10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
verification both related to zero-extension handling, from Ilya Leoshkevich.
11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.
12) Batch of AF_XDP selftest cleanups and small performance improvement
for libbpf's xsk map redirect for newer kernels, from Björn Töpel.
13) Follow-up BPF doc and verifier improvements around atomics with
BPF_FETCH, from Brendan Jackman.
14) Permit zero-sized data sections e.g. if ELF .rodata section contains
read-only data from local variables, from Yonghong Song.
15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switchdev_port_attr_set function prototype was updated only for the
case where CONFIG_SWITCHDEV=y|m, leaving a prototype mismatch with the
stub definition for the disabled case. This results in a build error, so
update that function too.
Fixes: dcbdf1350e33 ("net: bridge: propagate extack through switchdev_port_attr_set")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A userspace daemon like firewalld might need to monitor for netlink
updates to detect its ruleset removal by the (global) flush ruleset
command to ensure ruleset persistency. This adds extra complexity from
userspace and, for some little time, the firewall policy is not in
place.
This patch adds the NFT_TABLE_F_OWNER flag which allows a userspace
program to own the table that creates in exclusivity.
Tables that are owned...
- can only be updated and removed by the owner, non-owners hit EPERM if
they try to update it or remove it.
- are destroyed when the owner closes the netlink socket or the process
is gone (implicit netlink socket closure).
- are skipped by the global flush ruleset command.
- are listed in the global ruleset.
The userspace process that sets on the NFT_TABLE_F_OWNER flag need to
leave open the netlink socket.
A new NFTA_TABLE_OWNER netlink attribute specifies the netlink port ID
to identify the owner from userspace.
This patch also updates error reporting when an unknown table flag is
specified to change it from EINVAL to EOPNOTSUPP given that EINVAL is
usually reserved to report for malformed netlink messages to userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The benefit is the ability to propagate errors from switchdev drivers
for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL attributes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922c2 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce58b
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both tcp_data_ready() and tcp_stream_is_readable() share the same logic.
Add tcp_epollin_ready() helper to avoid duplication.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While commit 24adbc1676af ("tcp: fix SO_RCVLOWAT hangs with fat skbs")
fixed an issue vs too small sk_rcvbuf for given sk_rcvlowat constraint,
it missed to address issue caused by memory pressure.
1) If we are under memory pressure and socket receive queue is empty.
First incoming packet is allowed to be queued, after commit
76dfa6082032 ("tcp: allow one skb to be received per socket under memory pressure")
But we do not send EPOLLIN yet, in case tcp_data_ready() sees sk_rcvlowat
is bigger than skb length.
2) Then, when next packet comes, it is dropped, and we directly
call sk->sk_data_ready().
3) If application is using poll(), tcp_poll() will then use
tcp_stream_is_readable() and decide the socket receive queue is
not yet filled, so nothing will happen.
Even when sender retransmits packets, phases 2) & 3) repeat
and flow is effectively frozen, until memory pressure is off.
Fix is to consider tcp_under_memory_pressure() to take care
of global memory pressure or memcg pressure.
Fixes: 24adbc1676af ("tcp: fix SO_RCVLOWAT hangs with fat skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun Roy <arjunroy@google.com>
Suggested-by: Wei Wang <weiwan@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Last set of updates:
* more minstrel work from Felix to reduce the
probing overhead
* QoS for nl80211 control port frames
* STBC injection support
* and a couple of small fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once event support is added this may need to allocate memory while msk
lock is held with softirqs disabled.
Not using lock_fast also allows to do the allocation with GFP_KERNEL.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow user to disable HE mode, similar to how VHT and HT
can be disabled. Useful for testing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20210204144610.25971-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use a new config SOCK_RX_QUEUE_MAPPING to compile-in the socket
RX queue field and logic, instead of the XPS config.
This breaks dependency in XPS, and allows selecting it from non-XPS
use cases, as we do in the next patch.
In addition, use the new flag to wrap the logic in sk_rx_queue_get()
and protect access to the sk_rx_queue_mapping field, while keeping
the function exposed unconditionally, just like sk_rx_queue_set()
and sk_rx_queue_clear().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
el/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2021-02-11
Here's the main bluetooth-next pull request for 5.12:
- Add support for advertising monitor offliading using Microsoft
vendor extensions
- Add firmware download support for MediaTek MT7921U USB devices
- Suspend-related fixes for Qualcomm devices
- Add support for Intel GarfieldPeak controller
- Various other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is simpler to make net->net_cookie a plain u64
written once in setup_net() instead of looping
and using atomic64 helpers.
Lorenz Bauer wants to add SO_NETNS_COOKIE socket option
and this patch would makes his patch series simpler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding on DSA switches.
Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.
The DSA switch driver should then set netdev feature flags for the
HSR/PRP operation that it offloads.
NETIF_F_HW_HSR_TAG_INS
NETIF_F_HW_HSR_TAG_RM
NETIF_F_HW_HSR_FWD
NETIF_F_HW_HSR_DUP
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
%s/dest_mac_filter/dmac_filter/g
Fixes: e78ab164591f ("devlink: Add DMAC filter generic packet trap")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reported-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
