| Age | Commit message (Collapse) | Author |
|---|
|
The separate blocking pool is going away. Start by ignoring
GRND_RANDOM in getentropy(2).
This should not materially break any API. Any code that worked
without this change should work at least as well with this change.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Link: https://lore.kernel.org/r/705c5a091b63cc5da70c99304bb97e0109be0a26.1577088521.git.luto@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Link: https://lore.kernel.org/r/d5473b56cf1fa900ca4bd2b3fc1e5b8874399919.1577088521.git.luto@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Typically a MAC PCS auto-configures itself after it receives the
negotiated copper-side link settings from the PHY, but some MAC devices
are more special and need manual interpretation of the SGMII AN result.
In other cases, the PCS exposes the entire tx_config_reg base page as it
is transmitted on the wire during auto-negotiation, so it makes sense to
be able to decode the equivalent lp_advertised bit mask from the raw u16
(of course, "lp" considering the PCS to be the local PHY).
Therefore, add the bit definitions for the SGMII registers 4 and 5
(local device ability, link partner ability), as well as a link_mode
conversion helper that can be used to feed the AN results into
phy_resolve_aneg_linkmode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the layout of kcov_remote_arg the same for 32-bit and 64-bit code.
This makes it more convenient to write userspace apps that can be
compiled into 32-bit or 64-bit binaries and still work with the same
64-bit kernel.
Also use proper __u32 types in uapi headers instead of unsigned ints.
Link: http://lkml.kernel.org/r/9e91020876029cfefc9211ff747685eba9536426.1575638983.git.andreyknvl@google.com
Fixes: eec028c9386ed1a ("kcov: remote coverage support")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: "Jacky . Cao @ sony . com" <Jacky.Cao@sony.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds AMD-TEE driver.
* targets AMD APUs which has AMD Secure Processor with software-based
Trusted Execution Environment (TEE) support
* registers with TEE subsystem
* defines tee_driver_ops function callbacks
* kernel allocated memory is used as shared memory between normal
world and secure world.
* acts as REE (Rich Execution Environment) communication agent, which
uses the services of AMD Secure Processor driver to submit commands
for processing in TEE environment
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Co-developed-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Signed-off-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The v4l2_buffer structure contains a 'struct timeval' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
As in v4l2_event, handle this with a special case in video_put_user()
and video_get_user() to replace the memcpy there.
Since the structure also contains a pointer, there are now two
native versions (on 32-bit systems) as well as two compat versions
(on 64-bit systems), which unfortunately complicates the compat
handler quite a bit.
Duplicating the existing handlers for the new types is a safe
conversion for now, but unfortunately this may turn into a
maintenance burden later. A larger-scale rework of the
compat code might be a better alternative, but is out of scope
of the y2038 work.
Sparc64 needs a special case because of their special suseconds_t
definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The v4l2_event structure contains a 'struct timespec' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
While passing a 32-bit time_t here would be sufficient for CLOCK_MONOTONIC
timestamps, simply redefining the structure to use the kernel's
__kernel_old_timespec would not work for any library that uses a copy
of the linux/videodev2.h header file rather than including the copy from
the latest kernel headers.
This means the kernel has to be changed to handle both versions of the
structure layout on a 32-bit architecture. The easiest way to do this
is during the copy from/to user space.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As a preparation for adding 64-bit time_t support in the uapi,
change the drivers to no longer care about the format of the
timestamp field in struct v4l2_buffer.
The v4l2_timeval_to_ns() function is no longer needed in the
kernel after this, but there is userspace code relying on
it to be part of the uapi header.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: replace spaces by tabs]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Commandline parser: Add support for panel orientation, and per-mode options.
- Fix IOCTL naming for dma-buf heaps.
Cross-subsystem Changes:
- Rename DMA_HEAP_IOC_ALLOC to DMA_HEAP_IOCTL_ALLOC before it becomes abi.
- Change DMA-BUF system-heap's name to system.
- Fix leak in error handling in dma_heap_ioctl(), and make a symbol static.
- Fix udma-buf cpu access.
- Fix ti devicetree bindings.
Core Changes:
- Add CTA-861-G modes with VIC >= 193.
- Change error handling and remove bug_on in *drm_dev_init.
- Export drm_panel_of_backlight() correctly once more.
- Add support for lvds decoders.
- Convert drm/client and drm/(gem-,)fb-helper to drm-device based logging and update logging todo.
Driver Changes:
- Add support for dsi/px30 to rockchip.
- Add fb damage support to virtio.
- Use dma_resv locking wrappers in vc4, msm, etnaviv.
- Make functions in virtio static, and perform some simplifications.
- Add suspend support to sun4i.
- Add A64 mipi dsi support to sun4i.
- Add runtime pm suspend to komeda.
- Associated driver fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efc11139-1653-86bc-1b0f-0aefde219850@linux.intel.com
|
|
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
<linux/fscrypt.h> defines ioctl numbers using the macros like _IOWR()
which are defined in <linux/ioctl.h>, so <linux/ioctl.h> should be
included as a prerequisite, like it is in many other kernel headers.
In practice this doesn't really matter since anyone referencing these
ioctl numbers will almost certainly include <sys/ioctl.h> too in order
to actually call ioctl(). But we might as well fix this.
Link: https://lore.kernel.org/r/20191219185624.21251-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Extend the FS_IOC_ADD_ENCRYPTION_KEY ioctl to allow the raw key to be
specified by a Linux keyring key, rather than specified directly.
This is useful because fscrypt keys belong to a particular filesystem
instance, so they are destroyed when that filesystem is unmounted.
Usually this is desired. But in some cases, userspace may need to
unmount and re-mount the filesystem while keeping the keys, e.g. during
a system update. This requires keeping the keys somewhere else too.
The keys could be kept in memory in a userspace daemon. But depending
on the security architecture and assumptions, it can be preferable to
keep them only in kernel memory, where they are unreadable by userspace.
We also can't solve this by going back to the original fscrypt API
(where for each file, the master key was looked up in the process's
keyring hierarchy) because that caused lots of problems of its own.
Therefore, add the ability for FS_IOC_ADD_ENCRYPTION_KEY to accept a
Linux keyring key. This solves the problem by allowing userspace to (if
needed) save the keys securely in a Linux keyring for re-provisioning,
while still using the new fscrypt key management ioctls.
This is analogous to how dm-crypt accepts a Linux keyring key, but the
key is then stored internally in the dm-crypt data structures rather
than being looked up again each time the dm-crypt device is accessed.
Use a custom key type "fscrypt-provisioning" rather than one of the
existing key types such as "logon". This is strongly desired because it
enforces that these keys are only usable for a particular purpose: for
fscrypt as input to a particular KDF. Otherwise, the keys could also be
passed to any kernel API that accepts a "logon" key with any service
prefix, e.g. dm-crypt, UBIFS, or (recently proposed) AF_ALG. This would
risk leaking information about the raw key despite it ostensibly being
unreadable. Of course, this mistake has already been made for multiple
kernel APIs; but since this is a new API, let's do it right.
This patch has been tested using an xfstest which I wrote to test it.
Link: https://lore.kernel.org/r/20191119222447.226853-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove #ifdef pollution around nf_ingress(), from Lukas Wunner.
2) Document ingress hook in netdevice, also from Lukas.
3) Remove htons() in tunnel metadata port netlink attributes,
from Xin Long.
4) Missing erspan netlink attribute validation also from Xin Long.
5) Missing erspan version in tunnel, from Xin Long.
6) Missing attribute nest in NFTA_TUNNEL_KEY_OPTS_{VXLAN,ERSPAN}
Patch from Xin Long.
7) Missing nla_nest_cancel() in tunnel netlink dump path,
from Xin Long.
8) Remove two exported conntrack symbols with no clients,
from Florian Westphal.
9) Add nft_meta_get_eval_time() helper to nft_meta, from Florian.
10) Add nft_meta_pkttype helper for loopback, also from Florian.
11) Add nft_meta_socket uid helper, from Florian Westphal.
12) Add nft_meta_cgroup helper, from Florian.
13) Add nft_meta_ifkind helper, from Florian.
14) Group all interface related meta selector, from Florian.
15) Add nft_prandom_u32() helper, from Florian.
16) Add nft_meta_rtclassid helper, from Florian.
17) Add support for matching on the slave device index,
from Florian.
This batch, among other things, contains updates for the netfilter
tunnel netlink interface: This extension is still incomplete and lacking
proper userspace support which is actually my fault, I did not find the
time to go back and finish this. This update is breaking tunnel UAPI in
some aspects to fix it but do it better sooner than never.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement LINKSTATE_GET netlink request to get link state information.
At the moment, only link up flag as provided by ETHTOOL_GLINK ioctl command
is returned.
LINKSTATE_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send ETHTOOL_MSG_LINKMODES_NTF notification message whenever device link
settings or advertised modes are modified using ETHTOOL_MSG_LINKMODES_SET
netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.
The notification message has the same format as reply to LINKMODES_GET
request. ETHTOOL_MSG_LINKMODES_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.
As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKMODES_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKMODES_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement LINKMODES_SET netlink request to set advertised linkmodes and
related attributes as ETHTOOL_SLINKSETTINGS and ETHTOOL_SSET commands do.
The request allows setting autonegotiation flag, speed, duplex and
advertised link modes.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement LINKMODES_GET netlink request to get link modes related
information provided by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl
commands.
This request provides supported, advertised and peer advertised link modes,
autonegotiation flag, speed and duplex.
LINKMODES_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send ETHTOOL_MSG_LINKINFO_NTF notification message whenever device link
settings are modified using ETHTOOL_MSG_LINKINFO_SET netlink message or
ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.
The notification message has the same format as reply to LINKINFO_GET
request. ETHTOOL_MSG_LINKINFO_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.
As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKINFO_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKINFO_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement LINKINFO_SET netlink request to set link settings queried by
LINKINFO_GET message.
Only physical port, phy MDIO address and MDI(-X) control can be set,
attempt to modify MDI(-X) status and transceiver is rejected.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement LINKINFO_GET netlink request to get basic link settings provided
by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl commands.
This request provides settings not directly related to autonegotiation and
link mode selection: physical port, phy MDIO address, MDI(-X) status,
MDI(-X) control and transceiver.
LINKINFO_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Requests a contents of one or more string sets, i.e. indexed arrays of
strings; this information is provided by ETHTOOL_GSSET_INFO and
ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all
information can be retrieved with one request and mulitple string sets can
be requested at once.
There are three types of requests:
- no NLM_F_DUMP, no device: get "global" stringsets
- no NLM_F_DUMP, with device: get string sets related to the device
- NLM_F_DUMP, no device: get device related string sets for all devices
Client can request either all string sets of given type (global or device
related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only
set sizes (numbers of strings) are returned.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add infrastructure for ethtool netlink notifications. There is only one
multicast group "monitor" which is used to notify userspace about changes
and actions performed. Notification messages (types using suffix _NTF)
share the format with replies to GET requests.
Notifications are supposed to be broadcasted on every configuration change,
whether it is done using the netlink interface or ioctl one. Netlink SET
requests only trigger a notification if some data is actually changed.
To trigger an ethtool notification, both ethtool netlink and external code
use ethtool_notify() helper. This helper requires RTNL to be held and may
sleep. Handlers sending messages for specific notification message types
are registered in ethnl_notify_handlers array. As notifications can be
triggered from other code, ethnl_ok flag is used to prevent an attempt to
send notification before genetlink family is registered.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool netlink code uses common framework for passing arbitrary
length bit sets to allow future extensions. A bitset can be a list (only
one bitmap) or can consist of value and mask pair (used e.g. when client
want to modify only some bits). A bitset can use one of two formats:
verbose (bit by bit) or compact.
Verbose format consists of bitset size (number of bits), list flag and
an array of bit nests, telling which bits are part of the list or which
bits are in the mask and which of them are to be set. In requests, bits
can be identified by index (position) or by name. In replies, kernel
provides both index and name. Verbose format is suitable for "one shot"
applications like standard ethtool command as it avoids the need to
either keep bit names (e.g. link modes) in sync with kernel or having to
add an extra roundtrip for string set request (e.g. for private flags).
Compact format uses one (list) or two (value/mask) arrays of 32-bit
words to store the bitmap(s). It is more suitable for long running
applications (ethtool in monitor mode or network management daemons)
which can retrieve the names once and then pass only compact bitmaps to
save space.
Userspace requests can use either format; ETHTOOL_FLAG_COMPACT_BITSETS
flag in request header tells kernel which format to use in reply.
Notifications always use compact format.
As some code uses arrays of unsigned long for internal representation and
some arrays of u32 (or even a single u32), two sets of parse/compose
helpers are introduced. To avoid code duplication, helpers for unsigned
long arrays are implemented as wrappers around helpers for u32 arrays.
There are two reasons for this choice: (1) u32 arrays are more frequent in
ethtool code and (2) unsigned long array can be always interpreted as an
u32 array on little endian 64-bit and all 32-bit architectures while we
would need special handling for odd number of u32 words in the opposite
direction.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add common request/reply header definition and helpers to parse request
header and fill reply header. Provide ethnl_update_* helpers to update
structure members from request attributes (to be used for *_SET requests).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic genetlink and init infrastructure for the netlink interface, register
genetlink family "ethtool". Add CONFIG_ETHTOOL_NETLINK Kconfig option to
make the build optional. Add initial overall interface description into
Documentation/networking/ethtool-netlink.rst, further patches will add more
detailed information.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8be0 ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f802d ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc4096 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b868 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the LACP actor/partner state is now part of the uapi, rename the
3ad state defines with LACP prefix. The LACP prefix is preferred over
BOND_3AD as the LACP standard moved to 802.1AX.
Fixes: 826f66b30c2e3 ("bonding: move 802.3ad port state flags to uapi")
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to match on vrf slave ifindex or name.
In case there was no slave interface involved, store 0 in the
destination register just like existing iif/oif matching.
sdif(name) is restricted to the ipv4/ipv6 input and forward hooks,
as it depends on ip(6) stack parsing/storing info in skb->cb[].
Cc: Martin Willi <martin@strongswan.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Shrijeet Mukherjee <shrijeet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing PUSH MPLS action inserts MPLS header between ethernet header
and the IP header. Though this behaviour is fine for L3 VPN where an IP
packet is encapsulated inside a MPLS tunnel, it does not suffice the L2
VPN (l2 tunnelling) requirements. In L2 VPN the MPLS header should
encapsulate the ethernet packet.
The new mpls action ADD_MPLS inserts MPLS header at the start of the
packet or at the start of the l3 header depending on the value of l3 tunnel
flag in the ADD_MPLS arguments.
POP_MPLS action is extended to support ethertype 0x6558.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mere overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
|
|
To enable iproute2/tipc to generate backwards compatible
printouts and validate command parameters for nodes using a
<z.c.n> node address, it needs to be able to read the legacy
address flag from the kernel. The legacy address flag records
the way in which the node identity was originally specified.
The legacy address flag is requested by the netlink message
TIPC_NL_ADDR_LEGACY_GET. If the flag is set the attribute
TIPC_NLA_NET_ADDR_LEGACY is set in the return message.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The common use-case in production is to have multiple cgroup-bpf
programs per attach type that cover multiple use-cases. Such programs
are attached with BPF_F_ALLOW_MULTI and can be maintained by different
people.
Order of programs usually matters, for example imagine two egress
programs: the first one drops packets and the second one counts packets.
If they're swapped the result of counting program will be different.
It brings operational challenges with updating cgroup-bpf program(s)
attached with BPF_F_ALLOW_MULTI since there is no way to replace a
program:
* One way to update is to detach all programs first and then attach the
new version(s) again in the right order. This introduces an
interruption in the work a program is doing and may not be acceptable
(e.g. if it's egress firewall);
* Another way is attach the new version of a program first and only then
detach the old version. This introduces the time interval when two
versions of same program are working, what may not be acceptable if a
program is not idempotent. It also imposes additional burden on
program developers to make sure that two versions of their program can
co-exist.
Solve the problem by introducing a "replace" mode in BPF_PROG_ATTACH
command for cgroup-bpf programs being attached with BPF_F_ALLOW_MULTI
flag. This mode is enabled by newly introduced BPF_F_REPLACE attach flag
and bpf_attr.replace_bpf_fd attribute to pass fd of the old program to
replace
That way user can replace any program among those attached with
BPF_F_ALLOW_MULTI flag without the problems described above.
Details of the new API:
* If BPF_F_REPLACE is set but replace_bpf_fd doesn't have valid
descriptor of BPF program, BPF_PROG_ATTACH will return corresponding
error (EINVAL or EBADF).
* If replace_bpf_fd has valid descriptor of BPF program but such a
program is not attached to specified cgroup, BPF_PROG_ATTACH will
return ENOENT.
BPF_F_REPLACE is introduced to make the user intent clear, since
replace_bpf_fd alone can't be used for this (its default value, 0, is a
valid fd). BPF_F_REPLACE also makes it possible to extend the API in the
future (e.g. add BPF_F_BEFORE and BPF_F_AFTER if needed).
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Narkyiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/30cd850044a0057bdfcaaf154b7d2f39850ba813.1576741281.git.rdna@fb.com
|
|
Introduces a new Qdisc, which is based on 802.1Q-2014 wording. It is
PRIO-like in how it is configured, meaning one needs to specify how many
bands there are, how many are strict and how many are dwrr, quanta for the
latter, and priomap.
The new Qdisc operates like the PRIO / DRR combo would when configured as
per the standard. The strict classes, if any, are tried for traffic first.
When there's no traffic in any of the strict queues, the ETS ones (if any)
are treated in the same way as in DRR.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'struct timex' is one of the last users of 'struct timeval' and is
only referenced in one place in the kernel any more, to convert the
user space timex into the kernel-internal version on sparc64, with a
different tv_usec member type.
As a preparation for hiding the time_t definition and everything
using that in the kernel, change the implementation once more
to only convert the timeval member, and then enclose the
struct definition in an #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Take the renaming of timeval and timespec one level further,
also renaming itimerval to __kernel_old_itimerval, to avoid
namespace conflicts with the user-space structure that may
use 64-bit time_t members.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As there is only a 32-bit ac_btime field in taskstat and
we should handle dates after the overflow, add a new field
with the same information but 64-bit width that can hold
a full time64_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
In 'struct acct', 'struct acct_v3', and 'struct taskstats' we have
a 32-bit 'ac_btime' field containing an absolute time value, which
will overflow in year 2106.
There are two possible ways to deal with it:
a) let it overflow and have user space code deal with reconstructing
the data based on the current time, or
b) truncate the times based on the range of the u32 type.
Neither of them solves the actual problem. Pick the second
one to best document what the issue is, and have someone
fix it in a future version.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Currently, the meaning of the value returned by RTC_VL_READ is undocumented
and left to the driver implementation. In order to get more meaningful
values, define a set of values to use as to make clear to userspace what is
the status of the various voltages feeding the RTC.
Link: https://lore.kernel.org/r/20191214220259.621996-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This is more consistent with the DMA and DRM frameworks convention. This
patch is only a name change, no logic is changed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216133405.1001-2-afd@ti.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
|
|
This fixes two spelling errors in source code comments.
Signed-off-by: Josh Soref <jsoref@gmail.com>
[Jason: rewrote commit message]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want the staging driver fixes in here, and this resolves merge issues
with the isdn code that was pointed out in linux-next
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for extern variables, provided to BPF program by libbpf. Currently
the following extern variables are supported:
- LINUX_KERNEL_VERSION; version of a kernel in which BPF program is
executing, follows KERNEL_VERSION() macro convention, can be 4- and 8-byte
long;
- CONFIG_xxx values; a set of values of actual kernel config. Tristate,
boolean, strings, and integer values are supported.
Set of possible values is determined by declared type of extern variable.
Supported types of variables are:
- Tristate values. Are represented as `enum libbpf_tristate`. Accepted values
are **strictly** 'y', 'n', or 'm', which are represented as TRI_YES, TRI_NO,
or TRI_MODULE, respectively.
- Boolean values. Are represented as bool (_Bool) types. Accepted values are
'y' and 'n' only, turning into true/false values, respectively.
- Single-character values. Can be used both as a substritute for
bool/tristate, or as a small-range integer:
- 'y'/'n'/'m' are represented as is, as characters 'y', 'n', or 'm';
- integers in a range [-128, 127] or [0, 255] (depending on signedness of
char in target architecture) are recognized and represented with
respective values of char type.
- Strings. String values are declared as fixed-length char arrays. String of
up to that length will be accepted and put in first N bytes of char array,
with the rest of bytes zeroed out. If config string value is longer than
space alloted, it will be truncated and warning message emitted. Char array
is always zero terminated. String literals in config have to be enclosed in
double quotes, just like C-style string literals.
- Integers. 8-, 16-, 32-, and 64-bit integers are supported, both signed and
unsigned variants. Libbpf enforces parsed config value to be in the
supported range of corresponding integer type. Integers values in config can
be:
- decimal integers, with optional + and - signs;
- hexadecimal integers, prefixed with 0x or 0X;
- octal integers, starting with 0.
Config file itself is searched in /boot/config-$(uname -r) location with
fallback to /proc/config.gz, unless config path is specified explicitly
through bpf_object_open_opts' kernel_config_path option. Both gzipped and
plain text formats are supported. Libbpf adds explicit dependency on zlib
because of this, but this shouldn't be a problem, given libelf already depends
on zlib.
All detected extern variables, are put into a separate .extern internal map.
It, similarly to .rodata map, is marked as read-only from BPF program side, as
well as is frozen on load. This allows BPF verifier to track extern values as
constants and perform enhanced branch prediction and dead code elimination.
This can be relied upon for doing kernel version/feature detection and using
potentially unsupported field relocations or BPF helpers in a CO-RE-based BPF
program, while still having a single version of BPF program running on old and
new kernels. Selftests are validating this explicitly for unexisting BPF
helper.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191214014710.3449601-3-andriin@fb.com
|
|
This adds rx_bpdu, tx_bpdu, rx_tcn, tx_tcn, transition_blk,
transition_fwd xstats counters to the bridge ports copied over via
netlink, providing useful information for STP.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
The bond slave actor/partner operating state is exported as
bitfield to userspace, which lacks a way to interpret it, e.g.,
iproute2 only prints the state as a number:
ad_actor_oper_port_state 15
For userspace to interpret the bitfield, the bitfield definitions
should be part of the uapi. The bitfield itself is defined in the
802.3ad standard.
This commit moves the 802.3ad bitfield definitions to uapi.
Related iproute2 patches, soon to be posted upstream, use the new uapi
headers to pretty-print bond slave state, e.g., with ip -d link show
ad_actor_oper_port_state_str <active,short_timeout,aggregating,in_sync>
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:
The time fields now match between kernel and user space, but all following
fields are in the wrong place.
Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.
Fixes: 141e5dcaa735 ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942ebac ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
