| Age | Commit message (Collapse) | Author |
|---|
|
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to dev/netdev/etc printk helpers, add standard printk helpers
for the RDMA subsystem.
Example output:
efa 0000:00:06.0 efa_0: Hello World!
efa_0: Hello World! (no parent device set)
(NULL ib_device): Hello World! (ibdev is NULL)
Cc: Jason Baron <jbaron@akamai.com>
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
IEEE 802.1Q-2018 defines the concept of a cycle-time-extension, so the
last entry of a schedule before the start of a new schedule can be
extended, so "too-short" entries can be avoided.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1Q-2018 defines that a the cycle-time of a schedule may be
overridden, so the schedule is truncated to a determined "width".
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.
Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.
The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):
$ tc qdisc change taprio dev IFACE parent root \
base-time X \
sched-entry <CMD> <GATES> <INTERVAL> \
...
Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.
Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.
So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.
For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.
Example:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time $BASE_TIME \
sched-entry S 00 500000 \
sched-entry S 0f 500000 \
clockid CLOCK_TAI
The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.
With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the page_done callback into a separate iomap_page_ops structure and
add a page_prepare calback to be called before the next page is written
to. In gfs2, we'll want to start a transaction in page_prepare and end
it in page_done. Other filesystems that implement data journaling will
require the same kind of mechanism.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Commit 875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
introduces one extra flag of ITER_BVEC_FLAG_NO_REF, and this flag
is stored into iter->type.
However, iov_iter_type() doesn't consider the new added flag, fix
it by masking this flag in iov_iter_type().
Fixes: 875f1d0769cd ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into for-next/core
|
|
Ying triggered a call trace when doing an asconf testing:
BUG: scheduling while atomic: swapper/12/0/0x10000100
Call Trace:
<IRQ> [<ffffffffa4375904>] dump_stack+0x19/0x1b
[<ffffffffa436fcaf>] __schedule_bug+0x64/0x72
[<ffffffffa437b93a>] __schedule+0x9ba/0xa00
[<ffffffffa3cd5326>] __cond_resched+0x26/0x30
[<ffffffffa437bc4a>] _cond_resched+0x3a/0x50
[<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
[<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
[<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
[<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
[<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
[<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
[<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
[<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
[<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]
As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.
Vlad tried to fix this recursive call in Commit c0786693404c ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.
To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.
The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.
Create a MSI domain bus layer that allocates and frees MSIs for
a device.
APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Introduce irq_chip_{request,release}_resource_parent() apis so
that these can be used in hierarchical irqchips.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Each resource with in the device can be uniquely identified as defined
by TISCI. Since this is generic across the devices, resource allocation
also can be made generic instead of each client driver handling the
resource. So add helper apis to manage the resource.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
TISCI abstracts the handling of IRQ routes where interrupt sources
are not directly connected to host interrupt controller. Add support
for the set of TISCI commands for requesting and releasing IRQs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
TISCI provides support for getting the resources(IRQ, RING etc..)
assigned to a specific device. These resources can be handled by
the client and in turn sends TISCI cmd to configure the resources.
It is very important that client should keep track on usage of these
resources.
Add support for TISCI commands to get resource ranges.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
TISCI has been updated to have support for Resource management(like
interrupts etc..). And there can be multiple device instances of a
resource type in a SoC. So every driver corresponding to a resource type
should get a TISCI handle so that it can make TISCI calls. And each
DT node corresponding to a device should exist under its corresponding
bus node as per the SoC architecture.
But existing apis in TISCI library assumes that all TISCI users are
child nodes of TISCI. Which is not true in the above case. So introduce
(devm_)ti_sci_get_by_phandle() apis that can be used by TISCI users
to get TISCI handle using of phandle property.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since different types of hardware may or may not support this setting
per-port, DSA keeps it either in dsa_switch or in dsa_port.
While drivers may know the characteristics of their hardware and
retrieve it from the correct place without the need of helpers, it is
cumbersone to find out an unambigous answer from generic DSA code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This file has no copyright notice, but was added as part of a commit
adding another file using the default kernel GPLv2 license. Add
a matching SPDX tag.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The file already has the correct SPDX header.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All these files have some form of the usual GPLv2 or later boilerplate.
Switch them to use SPDX tags instead.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All these files have some form of the usual GPLv2 boilerplate. Switch
them to use SPDX tags instead.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In KVM, specially for nested guests, there is a dominant pattern of:
=> map guest memory -> do_something -> unmap guest memory
In addition to all this unnecessarily noise in the code due to boiler plate
code, most of the time the mapping function does not properly handle memory
that is not backed by "struct page". This new guest mapping API encapsulate
most of this boiler plate code and also handles guest memory that is not
backed by "struct page".
The current implementation of this API is using memremap for memory that is
not backed by a "struct page" which would lead to a huge slow-down if it
was used for high-frequency mapping operations. The API does not have any
effect on current setups where guest memory is backed by a "struct page".
Further patches are going to also introduce a pfn-cache which would
significantly improve the performance of the memremap case.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Inject a PMI for KVM guest when Intel PT working
in Host-Guest mode and Guest ToPA entry memory buffer
was completely filled.
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and fixes for 5.2
- VSIE crypto fixes
- new guest features for gen15
- disable halt polling for nested virtualization with overcommit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for a bunch of warnings/errors that the
syzbot has been finding with it's new-found ability to stress-test the
USB layer.
All of these are tiny, but fix real issues, and are marked for stable
as well. All of these have had lots of testing in linux-next as well"
* tag 'usb-5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: w1 ds2490: Fix bug caused by improper use of altsetting array
USB: yurex: Fix protection fault after device removal
usb: usbip: fix isoc packet num validation in get_pipe
USB: core: Fix bug caused by duplicate interface PM usage counter
USB: dummy-hcd: Fix failure to give back unlinked URBs
USB: core: Fix unterminated string returned by usb_string()
|
|
The same page optimization is a rather odd corner case, which is not
used outside bio.c and which really should not be used outside of bio.c
either - we have better highlevel helpers like the rq/bio mapping
helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-04-30
1) A lot of work to remove indirections from the xfrm code.
From Florian Westphal.
2) Support ESP offload in combination with gso partial.
From Boris Pismenny.
3) Remove some duplicated code from vti4.
From Jeremy Sowden.
Please note that there is merge conflict
between commit:
8742dc86d0c7 ("xfrm4: Fix uninitialized memory read in _decode_session4")
from the ipsec tree and commit:
c53ac41e3720 ("xfrm: remove decode_session indirection from afinfo_policy")
from the ipsec-next tree. The merge conflict will appear
when those trees get merged during the merge window.
The conflict can be solved as it is done in linux-next:
https://lkml.org/lkml/2019/4/25/1207
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2019-04-30
1) Fix an out-of-bound array accesses in __xfrm_policy_unlink.
From YueHaibing.
2) Reset the secpath on failure in the ESP GRO handlers
to avoid dereferencing an invalid pointer on error.
From Myungho Jung.
3) Add and revert a patch that tried to add rcu annotations
to netns_xfrm. From Su Yanjun.
4) Wait for rcu callbacks before freeing xfrm6_tunnel_spi_kmem.
From Su Yanjun.
5) Fix forgotten vti4 ipip tunnel deregistration.
From Jeremy Sowden:
6) Remove some duplicated log messages in vti4.
From Jeremy Sowden.
7) Don't use IPSEC_PROTO_ANY when flushing states because
this will flush only IPsec portocol speciffic states.
IPPROTO_ROUTING states may remain in the lists when
doing net exit. Fix this by replacing IPSEC_PROTO_ANY
with zero. From Cong Wang.
8) Add length check for UDP encapsulation to fix "Oversized IP packet"
warnings on receive side. From Sabrina Dubroca.
9) Fix xfrm interface lookup when the interface is associated to
a vrf layer 3 master device. From Martin Willi.
10) Reload header pointers after pskb_may_pull() in _decode_session4(),
otherwise we may read from uninitialized memory.
11) Update the documentation about xfrm[46]_gc_thresh, it
is not used anymore after the flowcache removal.
From Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'id' key returns the unique id of the conntrack entry as returned
by nf_ct_get_id().
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The API allows a conntrack helper to indicate its corresponding
NAT helper which then can be loaded and reference counted.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Each NAT helper creates a module alias which follows a pattern.
Use macros for consistency.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We use the zero and one to limit the boolean options setting.
After this patch we only set 0 or 1 to boolean options for nf
conntrack sysctl.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since nf_tables.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The nf_tables.h header is used in a lot of files, but it turns out
that there is only one actual user of nft_expr_clone().
Hence we relocate that function to be with the one consumer of it
and avoid having to process it with CPP for all the other files.
This will also enable a reduction in the other headers that the
nf_tables.h itself has to include just to be stand-alone, hence
a pending further significant reduction in the CPP content that
needs to get processed for each netfilter file.
Note that the explicit "inline" has been dropped as part of this
relocation. In similar changes to this, I believe Dave has asked
this be done, so we free up gcc to make the choice of whether to
inline or not.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use new flag VM_FLUSH_RESET_PERMS for handling freeing of special
permissioned memory in vmalloc and remove places where memory was set RW
before freeing which is no longer needed. Don't track if the memory is RO
anymore because it is now tracked in vmalloc.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-19-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to
immediately clear executable TLB entries before freeing pages, and handle
resetting permissions on the directmap. This flag is useful for any kind
of memory with elevated permissions, or where there can be related
permissions changes on the directmap. Today this is RO+X and RO memory.
Although this enables directly vfreeing non-writeable memory now,
non-writable memory cannot be freed in an interrupt because the allocation
itself is used as a node on deferred free list. So when RO memory needs to
be freed in an interrupt the code doing the vfree needs to have its own
work queue, as was the case before the deferred vfree list was added to
vmalloc.
For architectures with set_direct_map_ implementations this whole operation
can be done with one TLB flush when centralized like this. For others with
directmap permissions, currently only arm64, a backup method using
set_memory functions is used to reset the directmap. When arm64 adds
set_direct_map_ functions, this backup can be removed.
When the TLB is flushed to both remove TLB entries for the vmalloc range
mapping and the direct map permissions, the lazy purge operation could be
done to try to save a TLB flush later. However today vm_unmap_aliases
could flush a TLB range that does not include the directmap. So a helper
is added with extra parameters that can allow both the vmalloc address and
the direct mapping to be flushed during this operation. The behavior of the
normal vm_unmap_aliases function is unchanged.
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Suggested-by: Andy Lutomirski <luto@kernel.org>
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make hibernate handle unmapped pages on the direct map when
CONFIG_ARCH_HAS_SET_ALIAS=y is set. These functions allow for setting pages
to invalid configurations, so now hibernate should check if the pages have
valid mappings and handle if they are unmapped when doing a hibernate
save operation.
Previously this checking was already done when CONFIG_DEBUG_PAGEALLOC=y
was configured. It does not appear to have a big hibernating performance
impact. The speed of the saving operation before this change was measured
as 819.02 MB/s, and after was measured at 813.32 MB/s.
Before:
[ 4.670938] PM: Wrote 171996 kbytes in 0.21 seconds (819.02 MB/s)
After:
[ 4.504714] PM: Wrote 178932 kbytes in 0.22 seconds (813.32 MB/s)
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-16-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add two new functions set_direct_map_default_noflush() and
set_direct_map_invalid_noflush() for setting the direct map alias for the
page to its default valid permissions and to an invalid state that cannot
be cached in a TLB, respectively. These functions do not flush the TLB.
Note, __kernel_map_pages() does something similar but flushes the TLB and
doesn't reset the permission bits to default on all architectures.
Also add an ARCH config ARCH_HAS_SET_DIRECT_MAP for specifying whether
these have an actual implementation or a default empty one.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-15-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When modules and BPF filters are loaded, there is a time window in
which some memory is both writable and executable. An attacker that has
already found another vulnerability (e.g., a dangling pointer) might be
able to exploit this behavior to overwrite kernel code. Prevent having
writable executable PTEs in this stage.
In addition, avoiding having W+X mappings can also slightly simplify the
patching of modules code on initialization (e.g., by alternatives and
static-key), as would be done in the next patch. This was actually the
main motivation for this patch.
To avoid having W+X mappings, set them initially as RW (NX) and after
they are set as RO set them as X as well. Setting them as executable is
done as a separate step to avoid one core in which the old PTE is cached
(hence writable), and another which sees the updated PTE (executable),
which would break the W^X protection.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lkml.kernel.org/r/20190426001143.4983-12-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Provide a function for copying init_mm. This function will be later used
for setting a temporary mm.
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-6-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In order to have a separate address space for text poking, we need to
duplicate init_mm early during start_kernel(). This, however, introduces
a problem since uprobes functions are called from dup_mmap(), but
uprobes is still not initialized in this early stage.
Since uprobes initialization is necassary for fork, and since all the
dependant initialization has been done when fork is initialized (percpu
and vmalloc), move uprobes initialization to fork_init(). It does not
seem uprobes introduces any security problem for the poking_mm.
Crash and burn if uprobes initialization fails, similarly to other early
initializations. Change the init_probes() name to probes_init() to match
other early initialization functions name convention.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: ard.biesheuvel@linaro.org
Cc: deneen.t.dock@intel.com
Cc: kernel-hardening@lists.openwall.com
Cc: kristen@linux.intel.com
Cc: linux_dti@icloud.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190426232303.28381-6-nadav.amit@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
