| Age | Commit message (Collapse) | Author |
|---|
|
This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
I got the names of these fields wrong.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
These are often similar for CFI (parallel NOR) and for SPI NOR, but they
aren't always the same, for various reasons (different namespaces,
company acquisitions and renames, etc.). And some don't have CFI_MFR_*
entries at all.
So let's make a proper place to list the SPI NOR IDs, with all the SPI
NOR specific assumptions and comments.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
These status bits use different ways of representing similar integer
constants -- some are decimal, some are hex. Make them more consistent.
At the same time, impose my own preference, since IMO it's clearer what
these are when using the BIT() macro.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
We use BIT() in the header. No real problem for now, but it's better to
be accurate.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
There is a concern that if the platform firmware was involved in
the system resume that's being completed, some devices might have
been reset by it and if those devices had the power.direct_complete
flag set during the preceding suspend transition, they may stay
in a reset-power-on state indefinitely (until they are runtime-resumed
and then suspended again). That may not be a big deal from the
individual device's perspective, but if the system is an SoC, it may
be prevented from entering deep SoC-wide low-power states on idle
because of that.
The devices that are most likely to be affected by this issue are
PCI devices and ACPI-enumerated devices using the general ACPI PM
domain, so to prevent it from happening for those devices, force a
runtime resume for them if they have their power.direct_complete
flags set and the platform firmware was involved in the resume
transition currently in progress.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are quite a few cases in which device drivers, bus types or
even the PM core itself may benefit from knowing whether or not
the platform firmware will be involved in the upcoming system power
transition (during system suspend) or whether or not it was involved
in it (during system resume).
For this reason, introduce global system suspend flags that can be
used by the platform code to expose that information for the benefit
of the other parts of the kernel and make the ACPI core set them
as appropriate.
Users of the new flags will be added later.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
md-cluster: A better way for METADATA_UPDATED processing
The processing of METADATA_UPDATED message is too simple and prone to
errors. Besides, it would not update the internal data structures as
required.
This set of patches reads the superblock from one of the device of the MD
and checks for changes in the in-memory data structures. If there is a change,
it performs the necessary actions to keep the internal data structures
as it would be in the primary node.
An example is if a devices turns faulty. The algorithm is:
1. The initiator node marks the device as faulty and updates the superblock
2. The initiator node sends METADATA_UPDATED with an advisory device number to the rest of the nodes.
3. The receiving node on receiving the METADATA_UPDATED message
3.1 Reads the superblock
3.2 Detects a device has failed by comparing with memory structure
3.3 Calls the necessary functions to record the failure and get the device out of the active array.
3.4 Acknowledges the message.
The patch series also fixes adding the disk which was impacted because of
the changes.
Patches can also be found at
https://github.com/goldwynr/linux branch md-next
Changes since V2:
- Fix status synchrnoization after --add and --re-add operations
- Included Guoqing's patches on endian correctness, zeroing cmsg etc
- Restructure add_new_disk() and cancel()
|
|
The ->read_xxx() methods are all passed the page number the NAND controller
is supposed to read, but ->write_xxx() do not have such a parameter.
This is a problem if we want to properly implement data
scrambling/randomization in order to mitigate MLC sensibility to repeated
pattern: to prevent bitflips in adjacent pages in the same block we need
to avoid repeating the same pattern at the same offset in those pages,
hence the randomizer/scrambler engine need to be passed the page value
in order to adapt its seed accordingly.
Moreover, adding the page parameter to the ->write_xxx() methods add some
consistency to the current API.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Huang Shijie <shijie.huang@arm.com>
CC: Stefan Agner <stefan@agner.ch>
CC: devel@driverdev.osuosl.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Since OF is now a userselectable config symbol, having OF=y but OF_IRQ=n
is a valid combination for non-OF platforms, and OF=y does not guarantee
anymore that OF_IRQ is enabled (or we are building for SPARC).
Fixes the following build error with OF=y, IRQ_DOMAIN=n and SPI=y:
drivers/built-in.o: In function `spi_register_master':
(.text+0xc3ae): undefined reference to `irq_of_parse_and_map'
Makefile:935: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
of_irq_find_parent has no users outside of of_irq.c, so it does not make
sense to expose it in of_irq.h. Therefore remove the prototype and dummy
implmeentation and make the function static instead.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
of_msi_configure is part of of_irq.c, which is compiled in when OF_IRQ
is enabled, not just OF.
Also It is unconditionally called from of_platform_device_create_pdata,
which does not depend on OF_IRQ, just OF_ADDRESS, so we need a dummy
implementation in case of OF_ADDRESS=y but OF_IRQ=n.
Fixes: c706c239 ("of/platform: Assign MSI domain to platform device")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Some drivers use member screen_base of struct fb_info to store non-
__iomem pointers, creating the need for ugly __force typecasts to
avoid sparse warnings. This adds an alternate pointer without the
__iomem qualifyer for this use.
Signed-off-by: Lars Svensson <lars1.svensson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the IRQ domain documentation to reflect the changes made
while divorcing the domain infrastructure from Device Tree.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-18-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
As we continue to push of_node towards the outskirts of irq domains,
let's start tackling the case of msi_create_irq_domain and its little
friends.
This has limited impact in both PCI/MSI, platform MSI, and a few
drivers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-17-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
As we're about to start converting the various MSI layers to
use fwnode_handle instead of device_node, add irq_domain_create_hierarchy
as a directly equivalent of irq_domain_add_hierarchy (which still
exists as a compatibility interface).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-16-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Since nobody is using gic_init_bases anymore outside of the GIC
driver itself, let's do a bit of housekeeping and remove the now
useless entry point.
Only gic_init() is now exposed to the rest of the kernel for the
benefit of legacy systems.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In order to start embrassing irqdomains at the GSI level, introduce
a new initializer:
void acpi_set_irq_model(enum acpi_irq_model_id model,
struct fwnode_handle *fwnode);
where:
- model is the value assigned to acpi_irq_model
- fwnode is the identifier for the irqdomain mapping
GSI interrupts
As nobody calls this code yet, the current code is (mostly)
left in place.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In order to be able to reference an irqdomain from ACPI, we need
to be able to create an identifier, which is usually a struct
device_node.
This device node does't really fit the ACPI infrastructure, so
we cunningly allocate a new structure containing a fwnode_handle,
and return that.
This structure doesn't really point to a device (interrupt
controllers are not "real" devices in Linux), but as we cannot
really deny that they exist, we create them with a new fwnode_type
(FWNODE_IRQCHIP).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Just like we have irq_domain_add_{linear,tree} to create a irq domain
identified by an of_node, introduce irq_domain_create_{linear,tree}
that do the same thing, except that they take a struct fwnode_handle.
Existing functions get rewritten in terms of the new ones so that
everything keeps working as before (and __irq_domain_add is now
fwnode_handle based as well).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Just like we have irq_create_of_mapping, irq_create_fwspec_mapping
creates a IRQ domain mapping for an interrupt described in a
struct irq_fwspec.
irq_create_of_mapping gets rewritten in terms of the new function,
and the hack we introduced before gets removed (now that no stacked
irqchip uses of_phandle_args anymore).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far the closest thing to a generic IRQ specifier structure is
of_phandle_args, which happens to be pretty OF specific (the of_node
pointer in there is quite annoying).
Let's introduce 'struct irq_fwspec' that can be used in place of
of_phandle_args for OF, but also for other firmware implementations
(that'd be ACPI). This is used together with a new 'translate' method
that is the pendent of 'xlate'.
We convert irq_create_of_mapping to use this new structure (with a
small hack that will be removed later).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far, our irq domains are still looked up by device node.
Let's change this and allow a domain to be looked up using
a fwnode_handle pointer.
The existing interfaces are preserved with a couple of helpers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Now that we have everyone accessing the of_node field via the
irq_domain_get_of_node accessor, it is pretty easy to swap it
for a pointer to a fwnode_handle.
This translates into a few limited changes in __irq_domain_add,
and an updated irq_domain_get_of_node.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Bring in upstream updates for patches which depend on them
|
|
struct at91_can_data was used to pass a callback to the driver, allowing it
to switch the transceiver on and off. As all at91 boards are now using DT,
this is not used anymore, remove that structure.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The can subsystem communicates with user space using a bcm_msg_head
header, which contains two timestamps. This is problematic for
multiple reasons:
a) The structure layout is currently incompatible between 64-bit
user space and 32-bit user space, and cannot work in compat
mode (other than x32).
b) The timeval structure layout will change in 32-bit user
space when we fix the y2038 overflow problem by redefining
time_t to 64-bit, making new 32-bit user space incompatible
with the current kernel interface.
Cars last a long time and often use old kernels, so the actual
users of this code are the most likely ones to migrate to y2038
safe user space.
This tries to work around part of the problem by changing the
publicly visible user interface in the header, but not the binary
interface. Fortunately, the values passed around in the structure
are relative times and do not actually suffer from the y2038
overflow, so 32-bit is enough here.
We replace the use of 'struct timeval' with a newly defined
'struct bcm_timeval' that uses the exact same binary layout
as before and that still suffers from problem a) but not problem
b).
The downside of this approach is that any user space program
that currently assigns a timeval structure to these members
rather than writing the tv_sec/tv_usec portions individually
will suffer a compile-time error when built with an updated
kernel header. Fixing this error makes it work fine with old
and new headers though.
We could address problem a) by using '__u32' or 'int' members
rather than 'long', but that would have a more significant
downside in also breaking support for all existing 64-bit user
binaries that might be using this interface, which is likely
not acceptable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-can@vger.kernel.org
Cc: linux-api@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add operations to retrieve cached IPv6 dst entry from l3mdev device
and lookup IPv6 source address.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
|
|
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the WNM and unprotected WNM categories and mark the latter
as not robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Unprotected DMG and VHT action frames are not protected, reflect
that in the list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For location and connectivity services, userspace would often like
to know the time when the BSS was last seen. The current "last seen"
value is calculated in a way that makes it less useful, especially
if the system suspended in the meantime.
Add the ability for the driver to report a real CLOCK_BOOTTIME stamp
that can then be reported to userspace (if present).
Drivers wishing to use this must be converted to the new API to call
cfg80211_inform_bss_data() or cfg80211_inform_bss_frame_data(). They
need to ensure the reported value is accurate enough even when the
frame might have been buffered in the device (e.g. firmware.)
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[modified to use struct, inlines]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This reverts commit 5c48f1201744233d4f235c7dd916d5196ed20716.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function nf_ct_frag6_gather is called on both the input and the
output paths of the networking stack. In particular ipv6_defrag which
calls nf_ct_frag6_gather is called from both the the PRE_ROUTING chain
on input and the LOCAL_OUT chain on output.
The addition of a net parameter makes it explicit which network
namespace the packets are being reassembled in, and removes the need
for nf_ct_frag6_gather to guess.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ip_defrag is called on both the input and the output
paths of the networking stack. In particular conntrack when it is
tracking outbound packets from the local machine calls ip_defrag.
So add a struct net parameter and stop making ip_defrag guess which
network namespace it needs to defragment packets in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTA_ALIGNTO is currently define as 4. It has to be 4U to prevent warning
for RTA_ALIGN and RTA_DATA expansions when -Wconversion gcc option is
enabled.
This follows NLMSG_ALIGNTO definition in <include/uapi/linux/netlink.h>.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
iwlwifi
* some debugfs improvements
* fix signedness in beacon statistics
* deinline some functions to reduce size when device tracing is enabled
* filter beacons out in AP mode when no stations are associated
* deprecate firmwares version -12
* fix a runtime PM vs. legacy suspend race
* one-liner fix for a ToF bug
* clean-ups in the rx code
* small debugging improvement
* fix WoWLAN with new firmware versions
* more clean-ups towards multiple RX queues;
* some rate scaling fixes and improvements;
* some time-of-flight fixes;
* other generic improvements and clean-ups;
brcmfmac
* rework code dealing with multiple interfaces
* allow logging firmware console using debug level
* support for BCM4350, BCM4365, and BCM4366 PCIE devices
* fixed for legacy P2P and P2P device handling
* correct set and get tx-power
ath9k
* add support for Outside Context of a BSS (OCB) mode
mwifiex
* add USB multichannel feature
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows configuring how the source address of ICMP
redirect messages is selected; by default the old behaviour is
retained, while setting icmp_redirects_use_orig_daddr force the
usage of the destination address of the packet that caused the
redirect.
The new behaviour fits closely the RFC 5798 section 8.1.1, and fix the
following scenario:
Two machines are set up with VRRP to act as routers out of a subnet,
they have IPs x.x.x.1/24 and x.x.x.2/24, with VRRP holding on to
x.x.x.254/24.
If a host in said subnet needs to get an ICMP redirect from the VRRP
router, i.e. to reach a destination behind a different gateway, the
source IP in the ICMP redirect is chosen as the primary IP on the
interface that the packet arrived at, i.e. x.x.x.1 or x.x.x.2.
The host will then ignore said redirect, due to RFC 1122 section 3.2.2.2,
and will continue to use the wrong next-op.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reducing tcp_timewait_sock from 280 bytes to 272 bytes
allows SLAB to pack 15 objects per page instead of 14 (on x86)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One 32bit hole is following skc_refcnt, use it.
skc_incoming_cpu can also be an union for request_sock rcv_wnd.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_refcnt is dirtied for every TCP/UDP incoming packet.
This is a performance issue if multiple cpus hit a common socket,
or multiple sockets are chained due to SO_REUSEPORT.
By moving sk_refcnt 8 bytes further, first 128 bytes of sockets
are mostly read. As they contain the lookup keys, this has
a considerable performance impact, as cpus can cache them.
These 8 bytes are not wasted, we use them as a place holder
for various fields, depending on the socket type.
Tested:
SYN flood hitting a 16 RX queues NIC.
TCP listener using 16 sockets and SO_REUSEPORT
and SO_INCOMING_CPU for proper siloing.
Could process 6.0 Mpps SYN instead of 4.2 Mpps
Kernel profile looked like :
11.68% [kernel] [k] sha_transform
6.51% [kernel] [k] __inet_lookup_listener
5.07% [kernel] [k] __inet_lookup_established
4.15% [kernel] [k] memcpy_erms
3.46% [kernel] [k] ipt_do_table
2.74% [kernel] [k] fib_table_lookup
2.54% [kernel] [k] tcp_make_synack
2.34% [kernel] [k] tcp_conn_request
2.05% [kernel] [k] __netif_receive_skb_core
2.03% [kernel] [k] kmem_cache_alloc
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SO_INCOMING_CPU as added in commit 2c8c56e15df3 was a getsockopt() command
to fetch incoming cpu handling a particular TCP flow after accept()
This commits adds setsockopt() support and extends SO_REUSEPORT selection
logic : If a TCP listener or UDP socket has this option set, a packet is
delivered to this socket only if CPU handling the packet matches the specified
one.
This allows to build very efficient TCP servers, using one listener per
RX queue, as the associated TCP listener should only accept flows handled
in softirq by the same cpu.
This provides optimal NUMA behavior and keep cpu caches hot.
Note that __inet_lookup_listener() still has to iterate over the list of
all listeners. Following patch puts sk_refcnt in a different cache line
to let this iteration hit only shared and read mostly cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's useful to allow users to set fwmark for an individual packet,
without changing the socket state. The function this patch adds in
sock layer can be used by the protocols that need such a feature.
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
since eBPF programs and maps use kernel memory consider it 'locked' memory
from user accounting point of view and charge it against RLIMIT_MEMLOCK limit.
This limit is typically set to 64Kbytes by distros, so almost all
bpf+tracing programs would need to increase it, since they use maps,
but kernel charges maximum map size upfront.
For example the hash map of 1024 elements will be charged as 64Kbyte.
It's inconvenient for current users and changes current behavior for root,
but probably worth doing to be consistent root vs non-root.
Similar accounting logic is done by mmap of perf_event.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to let unprivileged users load and execute eBPF programs
teach verifier to prevent pointer leaks.
Verifier will prevent
- any arithmetic on pointers
(except R10+Imm which is used to compute stack addresses)
- comparison of pointers
(except if (map_value_ptr == 0) ... )
- passing pointers to helper functions
- indirectly passing pointers in stack to helper functions
- returning pointer from bpf program
- storing pointers into ctx or maps
Spill/fill of pointers into stack is allowed, but mangling
of pointers stored in the stack or reading them byte by byte is not.
Within bpf programs the pointers do exist, since programs need to
be able to access maps, pass skb pointer to LD_ABS insns, etc
but programs cannot pass such pointer values to the outside
or obfuscate them.
Only allow BPF_PROG_TYPE_SOCKET_FILTER unprivileged programs,
so that socket filters (tcpdump), af_packet (quic acceleration)
and future kcm can use it.
tracing and tc cls/act program types still require root permissions,
since tracing actually needs to be able to see all kernel pointers
and tc is for root only.
For example, the following unprivileged socket filter program is allowed:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += skb->len;
return 0;
}
but the following program is not:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += (u64) skb;
return 0;
}
since it would leak the kernel address into the map.
Unprivileged socket filter bpf programs have access to the
following helper functions:
- map lookup/update/delete (but they cannot store kernel pointers into them)
- get_random (it's already exposed to unprivileged user space)
- get_smp_processor_id
- tail_call into another socket filter program
- ktime_get_ns
The feature is controlled by sysctl kernel.unprivileged_bpf_disabled.
This toggle defaults to off (0), but can be set true (1). Once true,
bpf programs and maps cannot be accessed from unprivileged process,
and the toggle cannot be set back to false.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit cb7323fffa85 ("lockd: create and use per-net NSM
RPC clients on MON/UNMON requests") introduced per-net
NSM RPC clients. Unfortunately this doesn't make any sense
without per-net nsm_handle.
E.g. the following scenario could happen
Two hosts (X and Y) in different namespaces (A and B) share
the same nsm struct.
1. nsm_monitor(host_X) called => NSM rpc client created,
nsm->sm_monitored bit set.
2. nsm_mointor(host-Y) called => nsm->sm_monitored already set,
we just exit. Thus in namespace B ln->nsm_clnt == NULL.
3. host X destroyed => nsm->sm_count decremented to 1
4. host Y destroyed => nsm_unmonitor() => nsm_mon_unmon() => NULL-ptr
dereference of *ln->nsm_clnt
So this could be fixed by making per-net nsm_handles list,
instead of global. Thus different net namespaces will not be able
share the same nsm_handle.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Once genpd could be configured to be built with CONFIG_PM_RUNTIME unset
(nowadays CONFIG_PM), the pm_genpd_poweron() API served a purpose, since
it allowed users to power on a PM domain.
As such configuration no longer is supported, users shall solely rely on
using some of the runtime PM APIs to power on a PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
