| Age | Commit message (Collapse) | Author |
|---|
|
Syzkaller again found a path to a kernel crash through bad gso input.
By building an excessively large packet to cause an skb field to wrap.
If VIRTIO_NET_HDR_F_NEEDS_CSUM was set this would have been dropped in
skb_partial_csum_set.
GSO packets that do not set checksum offload are suspicious and rare.
Most callers of virtio_net_hdr_to_skb already pass them to
skb_probe_transport_header.
Move that test forward, change it to detect parse failure and drop
packets on failure as those cleary are not one of the legitimate
VIRTIO_NET_HDR_GSO types.
Fixes: bfd5f4a3d605 ("packet: Add GSO/csum offload support.")
Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).
So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:
1. When registering, specify how many vports to register. This number
is the same for both drivers which is the total available vport
numbers.
2. When unregistering, specify the number of registered vports to do
unregister. Also, unload the repersentors which are already loaded.
It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.
Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:
create: (none) -> unregistered
reg: unregistered -> registered
load: registered -> loaded
unload: loaded -> registered
unreg: registered -> unregistered
Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.
With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).
Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Commands referring to vports use the following scheme:
1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
referred vport and put 1 in other_vport. It was assumed that driver
is accessing other vport when vport number is greater than 0.
With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.
As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Merge mlx5-next shared branched into net-next,
From Bodong Wang:
1) Introduction of ECPF (Embedded CPU Physical Function), and low level
bits for mlx5 SmartNic capabilities support.
2) Vport enumeration refactoring that affect mlx5_ib and mlx5_core
From Aya Levin,
3) Add support for 50Gbps per lane link modes in the Port Type and Speed
register (PTYS)
4) Refactor low level query functions for PTYS register
5) Add support for 50Gbps per lane link modes to mlx5_ib
Note: due to a change in API in mlx5/core and a later patch from net-next,
a fixup was squashed with this merge commit that replaces FDB_UPLINK_VPORT
with MLX5_VPORT_UPLINK which exists only in upstream net-next.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the request_key() upcall mechanism there's a dependency loop by which if
a key type driver overrides the ->request_key hook and the userspace side
manages to lose the authorisation key, the auth key and the internal
construction record (struct key_construction) can keep each other pinned.
Fix this by the following changes:
(1) Killing off the construction record and using the auth key instead.
(2) Including the operation name in the auth key payload and making the
payload available outside of security/keys/.
(3) The ->request_key hook is given the authkey instead of the cons
record and operation name.
Changes (2) and (3) allow the auth key to naturally be cleaned up if the
keyring it is in is destroyed or cleared or the auth key is unlinked.
Fixes: 7ee02a316600 ("keys: Fix dependency loop between construction record and auth key")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.1 - Part 2
* Fixups/Cleanup for Qualcomm LLCC
* tag 'qcom-drivers-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/fixes
mt8173: minor typo in scpsys header file
mt7629: add smp bringup code
mt7623a: delete unused smp bringup code
* tag 'v5.0-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: mediatek: add MT7629 smp bring up code
Revert "ARM: mediatek: add MT7623a smp bringup code"
dt-bindings: soc: fix typo of MT8173 power dt-bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci SoC updates for v5.1 (part 2)
This pull request contains changes needed to help get rid of
hard-coded GPIO base value passed from DaVinci platform data.
The OHCI related changes also help by moving over-current support
from board-files to OHCI driver making future DT-coversion easy.
The OHCI parts are acked by its maintainer.
* tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
ARM: davinci: mityomapl138: use device properties for at24 eeprom
ARM: davinci: mityomapl138: use nvmem notifiers
ARM: davinci: remove dead code related to MAC address reading
ARM: davinci: sffsdr: use device properties for at24 eeprom
ARM: davinci: sffsdr: fix the at24 eeprom device name
ARM: davinci: dm646x-evm: use device properties for at24 eeprom
ARM: davinci: dm644x-evm: use device properties for at24 eeprom
ARM: davinci: da830-evm: use device properties for at24 eeprom
ARM: davinci: dm365-evm: use device properties for at24 eeprom
ARM: davinci: mityomapl138: don't read the MAC address from machine code
ARM: davinci: da850-evm: remove dead MTD code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target.
In particular, it triggers for all the init/cleanup_module
aliases in the kernel (defined by the module_init/exit macros),
ending up being very noisy.
These aliases point to the __init/__exit functions of a module,
which are defined as __cold (among other attributes). However,
the aliases themselves do not have the __cold attribute.
Since the compiler behaves differently when compiling a __cold
function as well as when compiling paths leading to calls
to __cold functions, the warning is trying to point out
the possibly-forgotten attribute in the alias.
In order to keep the warning enabled, we decided to silence
this case. Ideally, we would mark the aliases directly
as __init/__exit. However, there are currently around 132 modules
in the kernel which are missing __init/__exit in their init/cleanup
functions (either because they are missing, or for other reasons,
e.g. the functions being called from somewhere else); and
a section mismatch is a hard error.
A conservative alternative was to mark the aliases as __cold only.
However, since we would like to eventually enforce __init/__exit
to be always marked, we chose to use the new __copy function
attribute (introduced by GCC 9 as well to deal with this).
With it, we copy the attributes used by the target functions
into the aliases. This way, functions that were not marked
as __init/__exit won't have their aliases marked either,
and therefore there won't be a section mismatch.
Note that the warning would go away marking either the extern
declaration, the definition, or both. However, we only mark
the definition of the alias, since we do not want callers
(which only see the declaration) to be compiled as if the function
was __cold (and therefore the paths leading to those calls
would be assumed to be unlikely).
Link: https://lore.kernel.org/lkml/20190123173707.GA16603@gmail.com/
Link: https://lore.kernel.org/lkml/20190206175627.GA20399@gmail.com/
Suggested-by: Martin Sebor <msebor@gcc.gnu.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
From the GCC manual:
copy
copy(function)
The copy attribute applies the set of attributes with which function
has been declared to the declaration of the function to which
the attribute is applied. The attribute is designed for libraries
that define aliases or function resolvers that are expected
to specify the same set of attributes as their targets. The copy
attribute can be used with functions, variables, or types. However,
the kind of symbol to which the attribute is applied (either
function or variable) must match the kind of symbol to which
the argument refers. The copy attribute copies only syntactic and
semantic attributes but not attributes that affect a symbol’s
linkage or visibility such as alias, visibility, or weak.
The deprecated attribute is also not copied.
https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target, e.g.:
void __cold f(void) {}
void __alias("f") g(void);
diagnoses:
warning: 'g' specifies less restrictive attribute than
its target 'f': 'cold' [-Wmissing-attributes]
Using __copy(f) we can copy the __cold attribute from f to g:
void __cold f(void) {}
void __copy(f) __alias("f") g(void);
This attribute is most useful to deal with situations where an alias
is declared but we don't know the exact attributes the target has.
For instance, in the kernel, the widely used module_init/exit macros
define the init/cleanup_module aliases, but those cannot be marked
always as __init/__exit since some modules do not have their
functions marked as such.
Suggested-by: Martin Sebor <msebor@gcc.gnu.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
Library functions for endianness are aligned for 16/32/64 bits.
But hdcp sequence numbers are 24bits(big endian).
So for their conversion to and from u32 helper functions are developed.
v2:
Comment is updated. [Daniel]
Reviewed-by Uma.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550219730-17734-10-git-send-email-ramalingam.c@intel.com
|
|
Defining the mei-i915 interface functions and initialization of
the interface.
v2:
Adjust to the new interface changes. [Tomas]
Added further debug logs for the failures at MEI i/f.
port in hdcp_port data is equipped to handle -ve values.
v3:
mei comp is matched for global i915 comp master. [Daniel]
In hdcp_shim hdcp_protocol() is replaced with const variable. [Daniel]
mei wrappers are adjusted as per the i/f change [Daniel]
v4:
port initialization is done only at hdcp2_init only [Danvet]
v5:
I915 registers a subcomponent to be matched with mei_hdcp [Daniel]
v6:
HDCP_disable for all connectors incase of comp_unbind.
Tear down HDCP comp interface at i915_unload [Daniel]
v7:
Component init and fini are moved out of connector ops [Daniel]
hdcp_disable is not called from unbind. [Daniel]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> [v11]
[danvet: For the topic/mei-hdcp shared branch drop everything but the
header change needed by both drm/i915 and mei-hdcp. Also drop the no
longer needed device.h include.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550219730-17734-6-git-send-email-ramalingam.c@intel.com
|
|
Header defines the interface for the I915 and MEI_HDCP drivers.
This interface is specific to the usage of mei_hdcp from gen9+
platforms for ME FW based HDCP2.2 services.
And Generic HDCP2.2 protocol specific definitions
are added at drm/drm_hdcp.h.
v2:
Commit msg is enhanced [Daniel]
v3:
i915_hdcp_comp_master is defined.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> [v2]
Reviewed-by: Uma Shankar <uma.shankar@intel.com> [v2]
[danvet: Fix subject to drm/i915.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550219730-17734-4-git-send-email-ramalingam.c@intel.com
|
|
For the reusability of the enum port in other driver modules
(like mei_hdcp), enum port definition is moved from I915 local header
intel_display.h to drm/i915_drm.h
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fix subject prefix.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1550219730-17734-3-git-send-email-ramalingam.c@intel.com
|
|
into arm/drivers
This pull request contains Broadcom ARM/ARM64/MIPS based SoCs changes
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
* tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4)
soc: bcm: bcm2835-pm: Make local symbol static
soc: bcm: Make PM driver default for BCM2835
soc: bcm: bcm2835-pm: Add support for power domains under a new binding.
bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.
dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4)
firmware: raspberrypi: notify VC4 firmware of a reboot
soc: bcm2835: sync firmware properties with downstream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.1
* Add Qualcomm RPMh power domain driver and related changes
* Fix issues with sleep/wake sets and batch API in RPMh
* Update MAINTAINERS Qualcomm entry
* Fixup RMTFS-mem sysfs and uevents
* Fix error handling in GSBI
* Add SMD-RPM compatible entry for SDM660
* tag 'qcom-drivers-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
soc: qcom: smd-rpm: Add sdm660 compatible
soc: qcom: gsbi: Fix error handling in gsbi_probe()
soc: qcom: rpmh: Avoid accessing freed memory from batch API
drivers: qcom: rpmh: avoid sending sleep/wake sets immediately
soc: qcom: rmtfs-mem: Make sysfs attributes world-readable
soc: qcom: rmtfs-mem: Add class to enable uevents
soc: qcom: update config dependencies for QCOM_RPMPD
soc: qcom: rpmpd: Drop family A RPM dependency
MAINTAINERS: update list of qcom drivers
soc: qcom: rpmhpd: Mark mx as a parent for cx
soc: qcom: rpmhpd: Add RPMh power domain driver
soc: qcom: rpmpd: Add support for get/set performance state
soc: qcom: rpmpd: Add a Power domain driver to model corners
dt-bindings: power: Add qcom rpm power domain driver bindings
OPP: Add support for parsing the 'opp-level' property
dt-bindings: opp: Introduce opp-level bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.linaro.org/people/jens.wiklander/linux-tee into arm/drivers
Introduce TEE bus driver framework
- supp_nowait flag for non-blocking tee requests
- The tee bus driver framework
- OP-TEE TEE bus device enumeration support
- An OP-TEE based rng driver
* tag 'tee-bus-for-5.1' of https://git.linaro.org/people/jens.wiklander/linux-tee:
hwrng: add OP-TEE based rng driver
tee: optee: add TEE bus device enumeration support
tee: add bus driver framework for TEE based devices
tee: add supp_nowait flag in tee_context struct
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes intended for v5.0-rc7.
MMC core:
- Fix deadlock bug for block I/O requests
MMC host:
- sunxi: Disable broken HS-DDR mode for H5 by default
- sunxi: Avoid unsupported speed modes declared via DT
- meson-gx: Restore interrupt name"
* tag 'mmc-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: meson-gx: fix interrupt name
mmc: block: handle complete_work on separate workqueue
mmc: sunxi: Filter out unsupported modes declared in the device tree
mmc: sunxi: Disable HS-DDR mode for H5 eMMC controller by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.1-rc1
This contains a couple of miscellaneous fixes for minor issues and a
largish rework of the PMC driver to make it work on systems where the
PMC has been locked down and can only be accessed from secure firmware.
* tag 'tegra-for-5.1-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Support systems where PMC is marked secure
soc/tegra: pmc: Explicitly initialize all fields
soc/tegra: pmc: Make alignment consistent
soc/tegra: pmc: Pass struct tegra_pmc * where possible
soc/tegra: pmc: Make tegra_powergate_is_powered() a local function
soc/tegra: pmc: Add missing kerneldoc
soc/tegra: pmc: Sort includes alphabetically
soc/tegra: pmc: Use TEGRA186_ prefix for GPIO names
soc/tegra: fuse: Fix typo in tegra210_init_speedo_data
soc/tegra: fuse: Fix illegal free of IO base address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
firmware: tegra: Changes for v5.1-rc1
These changes add support for BPMP on Tegra210.
* tag 'tegra-for-5.1-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware/tegra: Enable Tegra186 BPMP support on Tegra194
firmware: tegra: Conditionally support SoC generations
firmware: tegra: bpmp-tegra186: Remove unused includes
firmware: tegra: add bpmp driver for Tegra210
firmware: tegra: Refactor BPMP driver
firmware: tegra: Reword messaging terminology
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm/drivers
Reset controller changes for v5.1
This adds the include/linux/reset directory to MAINTAINERS for reset
specific headers and adds headers for sunxi and socfpga in there to
get rid of a few extern function declarations.
There is a new reset driver for the Broadcom STB reset controller and
the i.MX7 system reset controller driver is extended to support i.MX8MQ
as well. Finally, there is a new header with reset id constants for
the Meson G12A SoC, which has a reset controller identical to Meson AXG
and thus can reuse its driver and DT bindings.
* tag 'reset-for-5.1' of git://git.pengutronix.de/git/pza/linux:
dt-bindings: reset: meson: add g12a bindings
reset: imx7: Add support for i.MX8MQ IP block variant
reset: imx7: Add plubming to support multiple IP variants
reset: Add Broadcom STB SW_INIT reset controller driver
dt-bindings: reset: Add document for Broadcom STB reset controller
reset: socfpga: declare socfpga_reset_init in a header file
reset: sunxi: declare sun6i_reset_init in a header file
MAINTAINERS: use include/linux/reset for reset controller related headers
dt-bindings: reset: imx7: Document usage on i.MX8MQ SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.1:
- Do not get GPCv2 driver depend on SOC_IMX8MQ since the driver is
going to be used on more SoCs than just i.MX8MQ.
- Add power domain information into SCU bindings document.
- Add support of start/stop a CPU into imx firmware driver.
- Support multiple address ranges per child node for imx-weim bus
driver.
* tag 'imx-drivers-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: Add support to start/stop a CPU
soc: imx: Break dependency on SOC_IMX8MQ for GPCv2
firmware: imx: scu-pd: add fallback compatible string support
dt-bindings: fsl: scu: add imx8qm scu power domain support
dt-bindings: fsl: scu: add fallback compatible string for power domain
bus: imx-weim: guard against timing configuration conflicts
bus: imx-weim: support multiple address ranges per child node
dt-bindings: bus: imx-weim: document multiple address ranges per child node
soc: imx: gpcv2: handle reset clocks
soc: imx: gpcv2: handle additional power-down bits in handshake register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm/drivers
arm64: zynqmp: SoC changes for v5.1
- Extend firmware interface with reset, nvmem,
power management and power domain support
- Add reset, nvmem driver, power management and
power domain drivers
-
* tag 'zynqmp-soc-for-v5.1' of https://github.com/Xilinx/linux-xlnx:
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
drivers: soc: xilinx: Add ZynqMP PM driver
firmware: xilinx: Implement ZynqMP power management APIs
dt-bindings: soc: Add ZynqMP PM bindings
nvmem: zynqmp: Added zynqmp nvmem firmware driver
dt-bindings: nvmem: Add bindings for ZynqMP nvmem driver
firmware: xilinx: Add zynqmp_pm_get_chipid() API
reset: reset-zynqmp: Adding support for Xilinx zynqmp reset controller.
dt-bindings: reset: Add bindings for ZynqMP reset driver
firmware: xilinx: Add reset API's
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Given a master fd we can then override the priority of the context
in another fd.
Using these overrides was recommended by Christian instead of trying
to submit from a master fd, and I am adding a way to override a
single context instead of the entire process so we can only upgrade
a single Vulkan queue and not effectively the entire process.
Reused the flags field as it was checked to be 0 anyways, so nothing
used it. This is source-incompatible (due to the name change), but
ABI compatible.
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull networking fixes from David Miller:
1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.
2) Probe SFP modules after being attached, from Russell King.
3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.
4) Revert some r8169 changes that are causing regressions, from Heiner
Kallweit.
5) Fix spurious connection timeouts in netfilter nat code, from Florian
Westphal.
6) SKB leak in tipc, from Hoang Le.
7) Short packet checkum issue in mlx4, similar to a previous mlx5
change, from Saeed Mahameed. The issue is that whilst padding bytes
are usually zero, it is not guarateed and the hardware doesn't take
the padding bytes into consideration when generating the checksum.
8) Fix various races in cls_tcindex, from Cong Wang.
9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
Long.
10) Fix locking in phy_is_started, from Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net: ethernet: freescale: set FEC ethtool regs version
net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
net: phy: fix potential race in the phylib state machine
net: phy: don't use locking in phy_is_started
selftests: fix timestamping Makefile
net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
net: fix possible overflow in __sk_mem_raise_allocated()
dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
net: phy: fix interrupt handling in non-started states
sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
net/mlx5e: XDP, fix redirect resources availability check
net/mlx5: Fix a compilation warning in events.c
net/mlx5: No command allowed when command interface is not ready
net/mlx5e: Fix NULL pointer derefernce in set channels error flow
netfilter: nft_compat: use-after-free when deleting targets
team: avoid complex list operations in team_nl_cmd_options_set()
net_sched: fix two more memory leaks in cls_tcindex
net_sched: fix a memory leak in cls_tcindex
...
|
|
Add an MTK (Mediatek) type to the "GNSS_TYPE" attribute.
Note that MTK receivers support a subset of NMEA 0183 with vendor
extensions.
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt
Renesas ARM Based SoC DT Updates for v5.1
* R-Car H2 (r8a7790) based Stout board
- Convert to new LVDS DT bindings
* R-Car H1 (r8a7779) and M1A (r8a7778) SoCs
- Describe HSCIF0/1 devices in DT
* RZ/G1M (r8a7743) SoC
- Correct sort order of the RWDT node
- Remove aliases: should be defined in board rather than SoC DT if needed
- Remove generic compatible string from iic3: it is not compatible
* RZ/G1N (r8a7744) SoC
- Describe LVDS and DU devices in DT
- Correct sort order of VSP and MSIOF noces
* RZ/G1C (r8a7747) based iWave SBC
- Enable RTC
* RZ/A2M (r7s9210) SoC and EVB
- Initial support
* tag 'renesas-arm-dt-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7744: Add LVDS support
ARM: dts: r8a7744: Add DU support
ARM: dts: r7s9210-rza2mevb: Add support for RZ/A2M EVB
ARM: dts: r7s9210: Initial SoC device tree
ARM: dts: r8a7779: Add HSCIF0/1 device nodes
ARM: dts: r8a7778: Add HSCIF0/1 support
ARM: dts: r8a7743: Fix sorting of rwdt node
ARM: dts: r8a7743: Remove aliases from SoC dtsi
ARM: dts: r8a7743: Remove generic compatible string from iic3
ARM: dts: r8a7744: Fix sorting of vsp and msiof nodes
ARM: dts: iwg23s-sbc: Enable RTC
ARM: dts: stout: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit c9b47cc1fabc ("xsk: fix bug when trying to use both copy and
zero-copy on one queue id") moved the umem query code to the AF_XDP
core, and therefore removed the need to query the netdevice for a
umem.
This patch removes XDP_QUERY_XSK_UMEM and all code that implement that
behavior, which is just dead code.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
As of the patch ("PM / Domains: Mark "name" const in
genpd_dev_pm_attach_by_name()") it's clear that the name in
dev_pm_domain_attach_by_name() can be const. Mark it as so. This
allows drivers to pass in a name that was declared "const" in a
driver.
Fixes: 27dceb81f445 ("PM / Domains: Introduce dev_pm_domain_attach_by_name()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The genpd_dev_pm_attach_by_name() simply takes the name and passes it
to of_property_match_string() where the argument is "const char *".
Adding a const here allows a later patch to add a const to
dev_pm_domain_attach_by_name() which allows drivers to pass in a name
that was declared "const" in a driver.
Fixes: 5d6be70add65 ("PM / Domains: Introduce option to attach a device by name to genpd")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some arc4 cipher algorithm defines show up in two places:
crypto/arc4.c and drivers/crypto/bcm/cipher.h.
Let's export them in a common header and update their users.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Counter values for per-channel interrupts and ring buffer full
conditions are useful for investigating performance.
Expose counters in sysfs for 2 types of guest to host interrupts:
1) Interrupts caused by the channel's outbound ring buffer transitioning
from empty to not empty
2) Interrupts caused by the channel's inbound ring buffer transitioning
from full to not full while a packet is waiting for enough buffer space to
become available
Expose 2 counters in sysfs for the number of times that write operations
encountered a full outbound ring buffer:
1) The total number of write operations that encountered a full
condition
2) The number of write operations that were the first to encounter a
full condition
Increment the outbound full condition counters in the
hv_ringbuffer_write() function because, for most drivers, a full
outbound ring buffer is detected in that function. Also increment the
outbound full condition counters in the set_channel_pending_send_size()
function. In the hv_sock driver, a full outbound ring buffer is detected
and set_channel_pending_send_size() is called before
hv_ringbuffer_write() is called.
I tested this patch by confirming that the sysfs files were created and
observing the counter values. The values seemed to increase by a
reasonable amount when the Hyper-v related drivers were in use.
Signed-off-by: Kimberly Brown <kimbrownkd@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: devel@linuxdriverproject.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Pick up upstream changes to avoid conflicts for pending patches.
|
|
This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When dealing with the offloads mode initialization, driver refers to
the number of VFs and add magic number one (1) to take account of the
uplink. This is not clear and will make the code less readable after
adding other vports (e.g. host PF). As these are special vports
compared to VF vports, add a helper macro to denote such special
vports and eliminate the use of magic number.
Moreover, when creating offloads flow table and groups, the driver
reserves two more slots for UC and MC miss rules. Replace this magic
number with a helper macro as well.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
These are two macros in the driver general header which deal with the
number of total vports and if a vport is vport manager. Such macros
are vport entities, better to place them at the vport header file.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Driver used to name uplink vport as FDB_UPLINK_VPORT, it's hard to
comply with the same naming convention along with the introduction of
other vports. Use MLX5_VPORT as the prefix for such vports and
relocate the uplink vport definition to public header file for the
benefits of both net and IB drivers.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
ECPF doesn't support SR-IOV, but an ECPF E-Switch manager shall know
the max VFs supported by its peer host PF in order to control those
VF vports.
The current driver implementation uses the total vfs quantity as
provided by the pci sub-system for an upper bound of the VF vports
the e-switch code needs to deal with. This obviously can't work as
is on ECPF e-switch manager. For now, we use a hard coded value of
128 on such systems.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.
The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
