| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Summary:
. Add atomic feature support
- Exynos also now supports atomic feature. However, it doesn't
guarantee atomic operation yet, and is required for more cleanups.
This time we just modified for Exynos drm driver to use atomic
interfaces instead of legacy ones. Next time, we will enhance
Exynos drm driver to support the atomic operation.
. Add iommu support
- This is a patch series according to below Exynos iommu integration
work with DT and dma-mapping subsystem,
http://lwn.net/Articles/607626/
. Consolidate Exynos drm driver initialization.
- This patch sereis resolves the issue that only the first compoments
was bound when happened deferred probing for other pipelines and
also makes the driver to be more cleanned up by moving the dispered
codes for registering kms drivers to one place.
. Add new MIC, DECON drivers, and MIPI-DSI support for Exynos5433.
- Add MIC(Mobile image compressor) driver. MIC is a new IP for Exynos5433
and later, which is used to transfer frame data to MIPI-DSI controller
compressing the data to reduce memory bandwidth.
- Add DECON driver for Exynos5433 SoC. This IP is a dislay controller
similar to Exynos7's one but this controller has much different registers
from Exynos7's ones so this driver has been implemented separately.
We will implement a helper modules for FIMD and two DECON controllers
to remove duplicated codes later.
- Add Exynos5433 SoC support to MIPI-DSI driver, and device tree
relevant patches.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (50 commits)
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
drm/exynos: fix the input prompt of Exynos7 DECON
drm/exynos: add drm_iommu_attach_device_if_possible()
drm/exynos: Add the dependency for DRM_EXYNOS to DPI/DSI/DP
drm/exynos: remove the dependency of DP driver for ARCH_EXYNOS
drm/exynos: do not wait for vblank at atomic operation
drm/exynos: Remove unused vma field of exynos_drm_gem_obj
drm/exynos: fimd: fix page fault issue with iommu
drm/exynos: iommu: improve a check for non-iommu dma_ops
drm/exynos: iommu: detach from default dma-mapping domain on init
...
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
One more drm-misc pull for 4.2. The important one is the fix from Laurent
for Daniel Stone's mode_blob work.
* tag 'topic/drm-misc-2015-06-22' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Don't set crtc_state->enable manually
drm: prime: Document gem_prime_mmap
drm: Avoid the double clflush on the last cache line in drm_clflush_virt_range()
drm/atomic: Extract needs_modeset function
drm/cma: Fix 64-bit size_t build warnings
Documentation/drm: Update rotation property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI updates from Ingo Molnar:
"EFI changes:
- Use idiomatic negative error values in efivar_create_sysfs_entry()
instead of returning '1' to indicate error (Dan Carpenter)
- Implement new support to expose the EFI System Resource Tables in
sysfs, which provides information for performing firmware updates
(Peter Jones)
- Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader (Alex Smith)
- Align the order of SMBIOS tables in /sys/firmware/efi/systab to
match the way that we do things for ACPI and add documentation to
Documentation/ABI (Jean Delvare)"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Work around ia64 build problem with ESRT driver
efi: Add 'systab' information to Documentation/ABI
efi: dmi: List SMBIOS3 table before SMBIOS table
efi/esrt: Fix some compiler warnings
x86, doc: Remove cmdline_size from list of fields to be filled in for EFI handover
efi: Add esrt support
efi: efivar_create_sysfs_entry() should return negative error codes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a46 ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes mostly consist of work on x86 PMU drivers:
- x86 Intel PT (hardware CPU tracer) improvements (Alexander
Shishkin)
- x86 Intel CQM (cache quality monitoring) improvements (Thomas
Gleixner)
- x86 Intel PEBSv3 support (Peter Zijlstra)
- x86 Intel PEBS interrupt batching support for lower overhead
sampling (Zheng Yan, Kan Liang)
- x86 PMU scheduler fixes and improvements (Peter Zijlstra)
There's too many tooling improvements to list them all - here are a
few select highlights:
'perf bench':
- Introduce new 'perf bench futex' benchmark: 'wake-parallel', to
measure parallel waker threads generating contention for kernel
locks (hb->lock). (Davidlohr Bueso)
'perf top', 'perf report':
- Allow disabling/enabling events dynamicaly in 'perf top':
a 'perf top' session can instantly become a 'perf report'
one, i.e. going from dynamic analysis to a static one,
returning to a dynamic one is possible, to toogle the
modes, just press 'f' to 'freeze/unfreeze' the sampling. (Arnaldo Carvalho de Melo)
- Make Ctrl-C stop processing on TUI, allowing interrupting the load of big
perf.data files (Namhyung Kim)
'perf probe': (Masami Hiramatsu)
- Support glob wildcards for function name
- Support $params special probe argument: Collect all function arguments
- Make --line checks validate C-style function name.
- Add --no-inlines option to avoid searching inline functions
- Greatly speed up 'perf probe --list' by caching debuginfo.
- Improve --filter support for 'perf probe', allowing using its arguments
on other commands, as --add, --del, etc.
'perf sched':
- Add option in 'perf sched' to merge like comms to lat output (Josef Bacik)
Plus tons of infrastructure work - in particular preparation for
upcoming threaded perf report support, but also lots of other work -
and fixes and other improvements. See (much) more details in the
shortlog and in the git log"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (305 commits)
perf tools: Configurable per thread proc map processing time out
perf tools: Add time out to force stop proc map processing
perf report: Fix sort__sym_cmp to also compare end of symbol
perf hists browser: React to unassigned hotkey pressing
perf top: Tell the user how to unfreeze events after pressing 'f'
perf hists browser: Honour the help line provided by builtin-{top,report}.c
perf hists browser: Do not exit when 'f' is pressed in 'report' mode
perf top: Replace CTRL+z with 'f' as hotkey for enable/disable events
perf annotate: Rename source_line_percent to source_line_samples
perf annotate: Display total number of samples with --show-total-period
perf tools: Ensure thread-stack is flushed
perf top: Allow disabling/enabling events dynamicly
perf evlist: Add toggle_enable() method
perf trace: Fix race condition at the end of started workloads
perf probe: Speed up perf probe --list by caching debuginfo
perf probe: Show usage even if the last event is skipped
perf tools: Move libtraceevent dynamic list to separated LDFLAGS variable
perf tools: Fix a problem when opening old perf.data with different byte order
perf tools: Ignore .config-detected in .gitignore
perf probe: Fix to return error if no probe is added
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes are:
- 'qspinlock' support, enabled on x86: queued spinlocks - these are
now the spinlock variant used by x86 as they outperform ticket
spinlocks in every category. (Waiman Long)
- 'pvqspinlock' support on x86: paravirtualized variant of queued
spinlocks. (Waiman Long, Peter Zijlstra)
- 'qrwlock' support, enabled on x86: queued rwlocks. Similar to
queued spinlocks, they are now the variant used by x86:
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
- various lockdep fixlets
- various locking primitives cleanups, further WRITE_ONCE()
propagation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
locking/lockdep: Remove hard coded array size dependency
locking/qrwlock: Don't contend with readers when setting _QW_WAITING
lockdep: Do not break user-visible string
locking/arch: Rename set_mb() to smp_store_mb()
locking/arch: Add WRITE_ONCE() to set_mb()
rtmutex: Warn if trylock is called from hard/softirq context
arch: Remove __ARCH_HAVE_CMPXCHG
locking/rtmutex: Drop usage of __HAVE_ARCH_CMPXCHG
locking/qrwlock: Rename QUEUE_RWLOCK to QUEUED_RWLOCKS
locking/pvqspinlock: Rename QUEUED_SPINLOCK to QUEUED_SPINLOCKS
locking/pvqspinlock: Replace xchg() by the more descriptive set_mb()
locking/pvqspinlock, x86: Enable PV qspinlock for Xen
locking/pvqspinlock, x86: Enable PV qspinlock for KVM
locking/pvqspinlock, x86: Implement the paravirt qspinlock call patching
locking/pvqspinlock: Implement simple paravirt support for the qspinlock
locking/qspinlock: Revert to test-and-set on hypervisors
locking/qspinlock: Use a simple write to grab the lock
locking/qspinlock: Optimize for smaller NR_CPUS
locking/qspinlock: Extract out code snippets for the next patch
locking/qspinlock: Add pending bit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
- Continued initialization/Kconfig updates: hide most Kconfig options
from unsuspecting users.
There's now a single high level configuration option:
*
* RCU Subsystem
*
Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)
Which if answered in the negative, leaves us with a single
interactive configuration option:
Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)
All the rest of the RCU options are configured automatically. Later
on we'll remove this single leftover configuration option as well.
- Remove all uses of RCU-protected array indexes: replace the
rcu_[access|dereference]_index_check() APIs with READ_ONCE() and
rcu_lockdep_assert()
- RCU CPU-hotplug cleanups
- Updates to Tiny RCU: a race fix and further code shrinkage.
- RCU torture-testing updates: fixes, speedups, cleanups and
documentation updates.
- Miscellaneous fixes
- Documentation updates
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
rcutorture: Allow repetition factors in Kconfig-fragment lists
rcutorture: Display "make oldconfig" errors
rcutorture: Update TREE_RCU-kconfig.txt
rcutorture: Make rcutorture scripts force RCU_EXPERT
rcutorture: Update configuration fragments for rcutree.rcu_fanout_exact
rcutorture: TASKS_RCU set directly, so don't explicitly set it
rcutorture: Test SRCU cleanup code path
rcutorture: Replace barriers with smp_store_release() and smp_load_acquire()
locktorture: Change longdelay_us to longdelay_ms
rcutorture: Allow negative values of nreaders to oversubscribe
rcutorture: Exchange TREE03 and TREE08 NR_CPUS, speed up CPU hotplug
rcutorture: Exchange TREE03 and TREE04 geometries
locktorture: fix deadlock in 'rw_lock_irq' type
rcu: Correctly handle non-empty Tiny RCU callback list with none ready
rcutorture: Test both RCU-sched and RCU-bh for Tiny RCU
rcu: Further shrink Tiny RCU by making empty functions static inlines
rcu: Conditionally compile RCU's eqs warnings
rcu: Remove prompt for RCU implementation
rcu: Make RCU able to tolerate undefined CONFIG_RCU_KTHREAD_PRIO
rcu: Make RCU able to tolerate undefined CONFIG_RCU_FANOUT_LEAF
...
|
|
This patch adds helper functions for registering/unregistering
LED Flash class devices as V4L2 sub-devices. The functions should
be called from the LED subsystem device driver. In case the
support for V4L2 Flash sub-devices is disabled in the kernel
config the functions' empty versions will be used.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"In this pile: pathname resolution rewrite.
- recursion in link_path_walk() is gone.
- nesting limits on symlinks are gone (the only limit remaining is
that the total amount of symlinks is no more than 40, no matter how
nested).
- "fast" (inline) symlinks are handled without leaving rcuwalk mode.
- stack footprint (independent of the nesting) is below kilobyte now,
about on par with what it used to be with one level of nested
symlinks and ~2.8 times lower than it used to be in the worst case.
- struct nameidata is entirely private to fs/namei.c now (not even
opaque pointers are being passed around).
- ->follow_link() and ->put_link() calling conventions had been
changed; all in-tree filesystems converted, out-of-tree should be
able to follow reasonably easily.
For out-of-tree conversions, see Documentation/filesystems/porting
for details (and in-tree filesystems for examples of conversion).
That has sat in -next since mid-May, seems to survive all testing
without regressions and merges clean with v4.1"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (131 commits)
turn user_{path_at,path,lpath,path_dir}() into static inlines
namei: move saved_nd pointer into struct nameidata
inline user_path_create()
inline user_path_parent()
namei: trim do_last() arguments
namei: stash dfd and name into nameidata
namei: fold path_cleanup() into terminate_walk()
namei: saner calling conventions for filename_parentat()
namei: saner calling conventions for filename_create()
namei: shift nameidata down into filename_parentat()
namei: make filename_lookup() reject ERR_PTR() passed as name
namei: shift nameidata inside filename_lookup()
namei: move putname() call into filename_lookup()
namei: pass the struct path to store the result down into path_lookupat()
namei: uninline set_root{,_rcu}()
namei: be careful with mountpoint crossings in follow_dotdot_rcu()
Documentation: remove outdated information from automount-support.txt
get rid of assorted nameidata-related debris
lustre: kill unused helper
lustre: kill unused macro (LOOKUP_CONTINUE)
...
|
|
'for-4.2/rmi', 'for-4.2/sensor-hub', 'for-4.2/sjoy', 'for-4.2/sony' and 'for-4.2/wacom' into for-linus
Conflicts:
drivers/hid/wacom_wac.c
|
|
'for-4.2/logitech' into for-linus
Conflicts:
drivers/hid/hid-logitech-hidpp.c
|
|
ST's Low Power Controller can currently operate in two supported modes;
Watchdog and Real Time Clock. These defines will aid engineers to easily
identify the selected mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
For the WM5102 there is a dependency in the core code on wm5102_patch()
which only exists when CONFIG_MFD_WM5102 is defined. To avoid having
to sprinkle #ifdefs around the code it is given an alternative empty
stub version when CONFIG_MFD_WM5102 is deselected
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Later arizona silicon has the single/differential selector
in a different register, and IN1_MODE only selects between
analogue or digital. Prepare for this by splitting the
INx_MODE definition into two fields.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The defined struct max77686_opmode_data isn't used neither by
the max77686 mfd driver nor the drivers for its sub-devices.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.
Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.
Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-i2c-input-chrome-4.2' into ibs-for-mfd-merged
|
|
When there are multiple ports or multiple endpoints in a port, they have to be
distinguished by the value of reg property. It is common. The drivers can get
the specific endpoint in the specific port via this function. Now the drivers
have to implement this code in themselves or have to force the order of dt nodes
to get the right node.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
DECON(Display and Enhancement Controller) is new IP replacing FIMD in
Exynos5433. This patch adds Exynos5433 decon driver.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
'regulator/topic/qcom' and 'regulator/topic/soft-start' into regulator-next
|
|
'regulator/topic/max14577', 'regulator/topic/max77693', 'regulator/topic/max77843' and 'regulator/topic/max8973' into regulator-next
|
|
'regulator/topic/doc', 'regulator/topic/fan53555', 'regulator/topic/gpio' and 'regulator/topic/ilim' into regulator-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Further updates for v4.2
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
|
|
|
|
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
|
|
As the AEAD conversion is still ongoing, we do not yet wish to
export legacy AEAD implementations to user-space, as their calling
convention will change.
This patch actually disables all AEAD algorithms because some of
them (e.g., cryptd) will need to be modified to propagate this flag.
Subsequent patches will reenable them on an individual basis.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds a new crypto_user command that allows the admin to
delete the crypto system RNG. Note that this can only be done if
the RNG is currently not in use. The next time it is used a new
system RNG will be allocated.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The header file cryptouser.h only contains information that is
exported to user-space.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently we free the default RNG when its use count hits zero.
This was OK when the IV generators would latch onto the RNG at
instance creation time and keep it until the instance is torn
down.
Now that IV generators only keep the RNG reference during init
time this scheme causes the default RNG to come and go at a high
frequencey. This is highly undesirable as we want to keep a single
RNG in use unless the admin wants it to be removed.
This patch changes the scheme so that the system RNG once allocated
is never removed unless a specifically requested.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
x86/core, to merge last updates
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Remove outdated comments and dead code from ext4_da_reserve_space.
Clean up its trace point, and relocate it to make it more useful.
While we're at it, fix a nearby conditional used to determine if
we have a non-bigalloc file system. It doesn't match usage elsewhere
in the code, and misleadingly suggests that an s_cluster_ratio value
of 0 would be legal.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
After Broadcom switched from MIPS to ARM for their home routers we need
to have NVRAM driver in some common place (not arch/mips/). As explained
in Kconfig, this driver is responsible for parsing SoC configuration
data that is passed to the kernel in flash from the bootloader firmware
called "CFE".
We were thinking about putting it in bus directory, however there are
two possible buses for MIPS: drivers/ssb/ and drivers/bcma/. So this
won't fit there and this is why I would like to move this driver to the
drivers/firmware/.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mike Waychison <mikew@google.com>
Cc: Roy Franz <roy.franz@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/10544/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Replace the simple GPIO chip registration by a platform driver
and make ath79_gpio_init() just register the device.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Host platforms such as routers supported by OpenWrt can
support NVRAM reading directly from internal NVRAM store.
The brcmfmac for one requires the complete nvram contents
to select what needs to be sent to wireless device.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10093/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add a binding document for the USB2.0 PHY found on the IMG Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Document the devicetree binding for Ingenic SoC CGUs, and add headers
defining the clock specifiers for clocks provided by the JZ4740 & JZ4780
CGU blocks.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10152/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move the driver for Ingenic SoC interrupt controllers into
drivers/irqchip where it belongs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
New devices may have more than 1 Ethernet core (device). We should
extract info about them to make it available to Ethernet drivers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Ian Kent <raven@themaw.net>
Patchwork: https://patchwork.linux-mips.org/patch/10027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
For years we planned to get rid of old u16 fields, let's start doing it
with MIPS code. This process will take some time, it requires doing the
same in ssb/bcma and then switching all drivers to new fields. This will
be handled in separated patches submitted to appropriate trees.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch adds getsockopt(SOL_NETLINK, NETLINK_LIST_MEMBERSHIPS) to
retrieve all groups a socket is a member of. Currently, we have to use
getsockname() and look at the nl.nl_groups bitmask. However, this mask is
limited to 32 groups. Hence, similar to NETLINK_ADD_MEMBERSHIP and
NETLINK_DROP_MEMBERSHIP, this adds a separate sockopt to manager higher
groups IDs than 32.
This new NETLINK_LIST_MEMBERSHIPS option takes a pointer to __u32 and the
size of the array. The array is filled with the full membership-set of the
socket, and the required array size is returned in optlen. Hence,
user-space can retry with a properly sized array in case it was too small.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Struct inet_proto no longer exists, so update the
comment which is out of date.
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
|
|
Folded into this merge commit is a build error fix: s/clk/core in
clk_change_rate due to the new struct clk_core
|
|
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 300000000
div_hpm rate: 300000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 300000000
div_pclk_dbg rate: 150000000
sclk_apll rate: 1200000000
sclk_apll_div_2 rate: 600000000
With use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 200000000
div_hpm rate: 200000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 240000000
div_pclk_dbg rate: 120000000
sclk_apll rate: 150000000
sclk_apll_div_2 rate: 75000000
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
Get the infrastructure patches which are required for x86/apic into core
|
|
System wide sampling like 'perf top' or 'perf record -a' read all
threads /proc/xxx/maps before sampling. If there are any threads which
generating a keeping growing huge maps, perf will do infinite loop
during synthesizing. Nothing will be sampled.
This patch fixes this issue by adding per-thread timeout to force stop
this kind of endless proc map processing.
PERF_RECORD_MISC_PROC_MAP_PARSE_TIME_OUT is introduced to indicate that
the mmap record are truncated by time out. User will get warning
notification when truncated mmap records are detected.
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ying Huang <ying.huang@intel.com>
Link: http://lkml.kernel.org/r/1434549071-25611-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
