| Age | Commit message (Collapse) | Author |
|---|
|
Defining it as a connector was a bad idea. Remove it while it is
not too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Defining it as a connector was a bad idea. Remove it while it is
not too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Each function range is quite narrow and especially for connectors this
will pose a problem. Increase the function ranges while we still can and
move the connector range to the end so that range is practically limitless.
[mchehab@osg.samsung.com: Rebased to apply at Linus tree]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
MEDIA_ENT_F_CONN_TEST is not really a connector, it is actually
a signal generator. Also, as other drivers use the
V4L2_CID_TEST_PATTERN control for signal generators, let's change
the driver accordingly.
Tested with Terratec Grabster AV350.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
On USB drivers, the dev struct is usually filled with the USB
device. That would mean that the name of the driver specified
by media_device.dev.driver.name would be "usb", instead of the
name of the actual driver that created the media entity.
Add an optional field at the internal struct to allow drivers
to override the driver name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The mutex lock at rc_register_device() was added by commit 08aeb7c9a42a
("[media] rc: add locking to fix register/show race").
It is meant to avoid race issues when trying to open a sysfs file while
the RC register didn't complete.
Adding a lock there causes troubles, as detected by the Kernel lock
debug instrumentation at the Kernel:
======================================================
[ INFO: possible circular locking dependency detected ]
4.5.0-rc3+ #46 Not tainted
-------------------------------------------------------
systemd-udevd/2681 is trying to acquire lock:
(s_active#171){++++.+}, at: [<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
but task is already holding lock:
(&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->lock){+.+.+.}:
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff822de966>] mutex_lock_nested+0xb6/0x860
[<ffffffffa0721f2b>] show_protocols+0x3b/0x3f0 [rc_core]
[<ffffffff81cdaba5>] dev_attr_show+0x45/0xc0
[<ffffffff8171f1b3>] sysfs_kf_seq_show+0x203/0x3c0
[<ffffffff8171a6a1>] kernfs_seq_show+0x121/0x1b0
[<ffffffff81617c71>] seq_read+0x2f1/0x1160
[<ffffffff8171c911>] kernfs_fop_read+0x321/0x460
[<ffffffff815abc20>] __vfs_read+0xe0/0x3d0
[<ffffffff815ae90e>] vfs_read+0xde/0x2d0
[<ffffffff815b1d01>] SyS_read+0x111/0x230
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
-> #0 (s_active#171){++++.+}:
[<ffffffff81244f24>] __lock_acquire+0x4304/0x5990
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff81717d3a>] __kernfs_remove+0x58a/0x810
[<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
[<ffffffff81721592>] remove_files.isra.0+0x72/0x190
[<ffffffff8172174b>] sysfs_remove_group+0x9b/0x150
[<ffffffff81721854>] sysfs_remove_groups+0x54/0xa0
[<ffffffff81cd97d0>] device_remove_attrs+0xb0/0x140
[<ffffffff81cdb27c>] device_del+0x38c/0x6b0
[<ffffffffa0724b8b>] rc_register_device+0x8cb/0x1450 [rc_core]
[<ffffffffa1326a7b>] dvb_usb_remote_init+0x66b/0x14d0 [dvb_usb]
[<ffffffffa1321c81>] dvb_usb_device_init+0xf21/0x1860 [dvb_usb]
[<ffffffffa13517dc>] dib0700_probe+0x14c/0x410 [dvb_usb_dib0700]
[<ffffffff81dbb1dd>] usb_probe_interface+0x45d/0x940
[<ffffffff81ce7e7a>] driver_probe_device+0x21a/0xc30
[<ffffffff81ce89b1>] __driver_attach+0x121/0x160
[<ffffffff81ce21bf>] bus_for_each_dev+0x11f/0x1a0
[<ffffffff81ce6cdd>] driver_attach+0x3d/0x50
[<ffffffff81ce5df9>] bus_add_driver+0x4c9/0x770
[<ffffffff81cea39c>] driver_register+0x18c/0x3b0
[<ffffffff81db6e98>] usb_register_driver+0x1f8/0x440
[<ffffffffa074001e>] dib0700_driver_init+0x1e/0x1000 [dvb_usb_dib0700]
[<ffffffff810021b1>] do_one_initcall+0x141/0x300
[<ffffffff8144d8eb>] do_init_module+0x1d0/0x5ad
[<ffffffff812f27b6>] load_module+0x6666/0x9ba0
[<ffffffff812f5fe8>] SyS_finit_module+0x108/0x130
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->lock);
lock(s_active#171);
lock(&dev->lock);
lock(s_active#171);
*** DEADLOCK ***
3 locks held by systemd-udevd/2681:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
In this specific case, some error happened during device init,
causing IR to be disabled.
Let's fix it by adding a var that will tell when the device is
initialized. Any calls before that will return a -EINVAL.
That should prevent the race issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of copying exactly the same code on all USB devices,
add an ancillary routine that will create and fill the
struct media_device with the values imported from the USB
device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Don't let it be included twice, to avoid compiler issues.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
SCPI specification v1.1 adds support for energy sensors. This patch
adds support for the same.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
SCPI specification version 1.1 extended the sensor from 32-bit to 64-bit
values in order to accommodate new sensor class with 64-bit requirements
Since the SCPI driver sets the higher 32-bit for older protocol version
to zeros, there's no need to explicitly check the SCPI protocol version
and the backward compatibility is maintainted.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The concept here was a suggestion from Ingo. The implementation
horrors are all mine.
This allows get_user_pages(), get_user_pages_unlocked(), and
get_user_pages_locked() to be called with or without the
leading tsk/mm arguments. We will give a compile-time warning
about the old style being __deprecated and we will also
WARN_ON() if the non-remote version is used for a remote-style
access.
Doing this, folks will get nice warnings and will not break the
build. This should be nice for -next and will hopefully let
developers fix up their own code instead of maintainers needing
to do it at merge time.
The way we do this is hideous. It uses the __VA_ARGS__ macro
functionality to call different functions based on the number
of arguments passed to the macro.
There's an additional hack to ensure that our EXPORT_SYMBOL()
of the deprecated symbols doesn't trigger a warning.
We should be able to remove this mess as soon as -rc1 hits in
the release after this is merged.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Geliang Tang <geliangtang@163.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Leon Romanovsky <leon@leon.nu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Xie XiuQi <xiexiuqi@huawei.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210155.73222EE1@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For protection keys, we need to understand whether protections
should be enforced in software or not. In general, we enforce
protections when working on our own task, but not when on others.
We call these "current" and "remote" operations.
This patch introduces a new get_user_pages() variant:
get_user_pages_remote()
Which is a replacement for when get_user_pages() is called on
non-current tsk/mm.
We also introduce a new gup flag: FOLL_REMOTE which can be used
for the "__" gup variants to get this new behavior.
The uprobes is_trap_at_addr() location holds mmap_sem and
calls get_user_pages(current->mm) on an instruction address. This
makes it a pretty unique gup caller. Being an instruction access
and also really originating from the kernel (vs. the app), I opted
to consider this a 'remote' access where protection keys will not
be enforced.
Without protection keys, this patch should not change any behavior.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: jack@suse.cz
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210154.3F0E51EA@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Provide a stable basis for the pkeys patches, which touches various
x86 details.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that all known users have been converted to use state latencies,
we can remove the latency field in the generic_pm_domain structure.
Signed-off-by: Axel Haslam <ahaslam+renesas@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some hardware (eg. OMAP), has the ability to enter different low power
modes for a given power domain. This allows for more fine grained control
over the power state of the platform. As a typical example, some registers
of the hardware may be implemented with retention flip-flops and be able
to retain their state at lower voltages allowing for faster on/off
latencies and an increased window of opportunity to enter an intermediate
low power state other than "off"
When trying to set a power domain to off, the genpd governor will choose
the deepest state that will respect the qos constraints of all the devices
and sub-domains on the power domain. The state chosen by the governor is
saved in the "state_idx" field of the generic_pm_domain structure and
shall be used by the power_off and power_on callbacks to perform the
necessary actions to set the power domain into (and out of) the state
indicated by state_idx.
States must be declared in ascending order from shallowest to deepest,
deepest meaning the state which takes longer to enter and exit.
For platforms that don't declare any states, a single a single "off"
state is used. Once all platforms are converted to use the state array,
the legacy on/off latencies will be removed.
[ Lina: Modified genpd state initialization and remove use of
save_state_latency_ns in genpd timing data ]
Suggested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Axel Haslam <ahaslam+renesas@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To fill the audio infoframe it is required to identify the
connection type as DP or HDMI. This patch adds an API which
parses ELD and returns the display type connected.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Introduction of a factor type and a variant containing a gate
to be able to also declare factor clocks in their correct
place in the clock tree instead of having to register factor
clocks in the init callback separately. And as always some more
clock-ids and non-regression fixes for mistakes introduced in
past kernel releases.
|
|
Add device managed APIs for regmap_add_irq_chip() and
regmap_del_irq_chip() so that it can be managed by
device framework for freeing it.
This helps on following:
1. Maintaining the sequence of resource allocation and deallocation
regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq)
On free path:
regmap_del_irq_chip(d);
and then removing the irq registration.
On this case, regmap irq is deleted before the irq is free.
This force to use normal irq registration.
By using devm apis, the sequence can be maintain properly:
devm_regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq);
and resource deallocation will be done in reverse order
by device framework.
2. No need to delete the regmap_irq_chip in error path or remove
callback and hence there is less code on this path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Topology will also create FE DAI links dynamically from the PCM
objects. These links will be removed when the component is removed
and its topology info is unloaded.
The component driver can implement link_load/unload ops for extra
intialization (e.g. error check) and destruction.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Topology will create FE DAIs dynamically from the PCM objects,
and register them to the component.
A PCM topoplogy object describes a FE DAI and DAI link. Later
patch will add FE DAI links as well.
Change tplg load ops for DAI:
- Only process a DAI.
- Pass the DAI driver pointer to the component driver for
extra initialization.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In my randconfig tests, I came across a bug that involves several
components:
* gcc-4.9 through at least 5.3
* CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files
* CONFIG_PROFILE_ALL_BRANCHES overriding every if()
* The optimized implementation of do_div() that tries to
replace a library call with an division by multiplication
* code in drivers/media/dvb-frontends/zl10353.c doing
u32 adc_clock = 450560; /* 45.056 MHz */
if (state->config.adc_clock)
adc_clock = state->config.adc_clock;
do_div(value, adc_clock);
In this case, gcc fails to determine whether the divisor
in do_div() is __builtin_constant_p(). In particular, it
concludes that __builtin_constant_p(adc_clock) is false, while
__builtin_constant_p(!!adc_clock) is true.
That in turn throws off the logic in do_div() that also uses
__builtin_constant_p(), and instead of picking either the
constant- optimized division, and the code in ilog2() that uses
__builtin_constant_p() to figure out whether it knows the answer at
compile time. The result is a link error from failing to find
multiple symbols that should never have been called based on
the __builtin_constant_p():
dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN'
dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod'
ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined!
ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined!
This patch avoids the problem by changing __trace_if() to check
whether the condition is known at compile-time to be nonzero, rather
than checking whether it is actually a constant.
I see this one link error in roughly one out of 1600 randconfig builds
on ARM, and the patch fixes all known instances.
Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.de
Acked-by: Nicolas Pitre <nico@linaro.org>
Fixes: ab3c9c686e22 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y")
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The tracepoint infrastructure uses RCU sched protection to enable and
disable tracepoints safely. There are some instances where tracepoints are
used in infrastructure code (like kfree()) that get called after a CPU is
going offline, and perhaps when it is coming back online but hasn't been
registered yet.
This can probuce the following warning:
[ INFO: suspicious RCU usage. ]
4.4.0-00006-g0fe53e8-dirty #34 Tainted: G S
-------------------------------
include/trace/events/kmem.h:141 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU! rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/8/0.
stack backtrace:
CPU: 8 PID: 0 Comm: swapper/8 Tainted: G S 4.4.0-00006-g0fe53e8-dirty #34
Call Trace:
[c0000005b76c78d0] [c0000000008b9540] .dump_stack+0x98/0xd4 (unreliable)
[c0000005b76c7950] [c00000000010c898] .lockdep_rcu_suspicious+0x108/0x170
[c0000005b76c79e0] [c00000000029adc0] .kfree+0x390/0x440
[c0000005b76c7a80] [c000000000055f74] .destroy_context+0x44/0x100
[c0000005b76c7b00] [c0000000000934a0] .__mmdrop+0x60/0x150
[c0000005b76c7b90] [c0000000000e3ff0] .idle_task_exit+0x130/0x140
[c0000005b76c7c20] [c000000000075804] .pseries_mach_cpu_die+0x64/0x310
[c0000005b76c7cd0] [c000000000043e7c] .cpu_die+0x3c/0x60
[c0000005b76c7d40] [c0000000000188d8] .arch_cpu_idle_dead+0x28/0x40
[c0000005b76c7db0] [c000000000101e6c] .cpu_startup_entry+0x50c/0x560
[c0000005b76c7ed0] [c000000000043bd8] .start_secondary+0x328/0x360
[c0000005b76c7f90] [c000000000008a6c] start_secondary_prolog+0x10/0x14
This warning is not a false positive either. RCU is not protecting code that
is being executed while the CPU is offline.
Instead of playing "whack-a-mole(TM)" and adding conditional statements to
the tracepoints we find that are used in this instance, simply add a
cpu_online() test to the tracepoint code where the tracepoint will be
ignored if the CPU is offline.
Use of raw_smp_processor_id() is fine, as there should never be a case where
the tracepoint code goes from running on a CPU that is online and suddenly
gets migrated to a CPU that is offline.
Link: http://lkml.kernel.org/r/1455387773-4245-1-git-send-email-kda@linux-powerpc.org
Reported-by: Denis Kirjanov <kda@linux-powerpc.org>
Fixes: 97e1c18e8d17b ("tracing: Kernel Tracepoints")
Cc: stable@vger.kernel.org # v2.6.28+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
According to the VT-d specification we need to clear the PPR bit in
the Page Request Status register when handling page requests, or the
hardware won't generate any more interrupts.
This wasn't actually necessary on SKL/KBL (which may well be the
subject of a hardware erratum, although it's harmless enough). But
other implementations do appear to get it right, and we only ever get
one interrupt unless we clear the PPR bit.
Reported-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
|
|
With ppc64 we use the deposited pgtable_t to store the hash pte slot
information. We should not withdraw the deposited pgtable_t without
marking the pmd none. This ensure that low level hash fault handling
will skip this huge pte and we will handle them at upper levels.
Recent change to pmd splitting changed the above in order to handle the
race between pmd split and exit_mmap. The race is explained below.
Consider following race:
CPU0 CPU1
shrink_page_list()
add_to_swap()
split_huge_page_to_list()
__split_huge_pmd_locked()
pmdp_huge_clear_flush_notify()
// pmd_none() == true
exit_mmap()
unmap_vmas()
zap_pmd_range()
// no action on pmd since pmd_none() == true
pmd_populate()
As result the THP will not be freed. The leak is detected by check_mm():
BUG: Bad rss-counter state mm:ffff880058d2e580 idx:1 val:512
The above required us to not mark pmd none during a pmd split.
The fix for ppc is to clear the huge pte of _PAGE_USER, so that low
level fault handling code skip this pte. At higher level we do take ptl
lock. That should serialze us against the pmd split. Once the lock is
acquired we do check the pmd again using pmd_same. That should always
return false for us and hence we should retry the access. We do the
pmd_same check in all case after taking plt with
THP (do_huge_pmd_wp_page, do_huge_pmd_numa_page and
huge_pmd_set_accessed)
Also make sure we wait for irq disable section in other cpus to finish
before flipping a huge pte entry with a regular pmd entry. Code paths
like find_linux_pte_or_hugepte depend on irq disable to get
a stable pte_t pointer. A parallel thp split need to make sure we
don't convert a pmd pte to a regular pmd entry without waiting for the
irq disable section to finish.
Fixes: eef1b3ba053a ("thp: implement split_huge_pmd()")
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds power supply types for USB chargers defined in
the USB Type-C Specification 1.1 and in the
USB Power Delivery Specification Revision 2.0 V1.1.
The following are added :
POWER_SUPPLY_TYPE_USB_TYPE_C, /* Type C Port */
POWER_SUPPLY_TYPE_USB_PD, /* Power Delivery Port */
POWER_SUPPLY_TYPE_USB_PD_DRP, /* PD Dual Role Port */
Signed-off-by: Benson Leung <bleung@chromium.org>
[tomeu: remove the mention to Type C from the comments]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Implement an 'ti,external-control' option for when the charger
shouldn't be configured by the host.
Signed-off-by: Jonathan Tinkham <sctincman@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add a new interface for userspace to preallocate memory that can be
used with usbfs. This gives two primary benefits:
- Zerocopy; data no longer needs to be copied between the userspace
and the kernel, but can instead be read directly by the driver from
userspace's buffers. This works for all kinds of transfers (even if
nonsensical for control and interrupt transfers); isochronous also
no longer need to memset() the buffer to zero to avoid leaking kernel data.
- Once the buffers are allocated, USB transfers can no longer fail due to
memory fragmentation; previously, long-running programs could run into
problems finding a large enough contiguous memory chunk, especially on
embedded systems or at high rates.
Memory is allocated by using mmap() against the usbfs file descriptor,
and similarly deallocated by munmap(). Once memory has been allocated,
using it as pointers to a bulk or isochronous operation means you will
automatically get zerocopy behavior. Note that this also means you cannot
modify outgoing data until the transfer is complete. The same holds for
data on the same cache lines as incoming data; DMA modifying them at the
same time could lead to your changes being overwritten.
There's a new capability USBDEVFS_CAP_MMAP that userspace can query to see
if the running kernel supports this functionality, if just trying mmap() is
not acceptable.
Largely based on a patch by Markus Rechberger with some updates. The original
patch can be found at:
http://sundtek.de/support/devio_mmap_v0.4.diff
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.1 devices that support precision time measurement have an
additional PTM cabaility descriptor as part of the full BOS descriptor
Look for this descriptor while parsing the BOS descriptor, and store it in
struct usb_hub_bos if it exists.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.1 devices can return a new SuperSpeedPlus isoc endpoint companion
descriptor for a isochronous endpoint that requires more than 48K bytes
per Service Interval.
The new descriptor immediately follows the old USB 3.0 SuperSpeed Endpoint
Companion and will provide a new BytesPerInterval value.
It is parsed and stored in struct usb_host_endpoint with the other endpoint
related descriptors, and should be used by USB3.1 capable hosts to reserve
bus time in the schedule.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB3.1 specifies a SuperSpeedPlus Isoc endpoint companion descriptor
which is returned as part of the devices complete configuration
descriptor.
It contains number of bytes per service interval which is needed when
reserving bus time in the schedule for transfers over 48K bytes per
service interval.
If bmAttributes bit 7 is set in the old SuperSpeed Endpoint Companion
descriptor, it will be ollowed by the new SuperSpeedPlus Isoc Endpoint
Companion descriptor.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here, and this resolves a merge error in tty_io.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 4.5-rc4
that resolve some reported issues.
One of them got reverted as it wasn't correct based on testing, and
all have been in linux-next for a while"
* tag 'tty-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "8250: uniphier: allow modular build with 8250 console"
pty: make sure super_block is still valid in final /dev/tty close
pty: fix possible use after free of tty->driver_data
tty: Add support for PCIe WCH382 2S multi-IO card
serial/omap: mark wait_for_xmitr as __maybe_unused
serial: omap: Prevent DoS using unprivileged ioctl(TIOCSRS485)
8250: uniphier: allow modular build with 8250 console
tty: Drop krefs for interrupted tty lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix preventing a 32bit overflow in timespec/val to cputime
conversions on 32bit machines"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
|
|
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the long awaited series to address a set of bugs around
active I/O remote-port LUN_RESET, as well as properly handling this
same case with concurrent fabric driver session disconnect ->
reconnect.
Note this set of LUN_RESET bug-fixes has been surviving extended
testing on both v4.5-rc1 and v3.14.y code over the last weeks, and is
CC'ed for stable as it's something folks using multiple ESX connected
hosts with slow backends can certainly trigger.
The highlights also include:
- Fix WRITE_SAME/DISCARD emulation 4k sector conversion in
target/iblock (Mike Christie)
- Fix TMR abort interaction and AIO type TMR response in qla2xxx
target (Quinn Tran + Swapnil Nagle)
- Fix >= v3.17 stale descriptor pointer regression in qla2xxx target
(Quinn Tran)
- Fix >= v4.5-rc1 return regression with unmap_zeros_data_store new
configfs store handler (nab)
- Add CPU affinity flag + convert qla2xxx to use bit (Quinn + HCH +
Bart)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: use TARGET_SCF_USE_CPUID flag to indiate CPU Affinity
target/transport: add flag to indicate CPU Affinity is observed
target: Fix incorrect unmap_zeroes_data_store return
qla2xxx: Use ATIO type to send correct tmr response
qla2xxx: Fix stale pointer access.
target/user: Fix cast from pointer to phys_addr_t
target: Drop legacy se_cmd->task_stop_comp + REQUEST_STOP usage
target: Fix race with SCF_SEND_DELAYED_TAS handling
target: Fix remote-port TMR ABORT + se_cmd fabric stop
target: Fix TAS handling for multi-session se_node_acls
target: Fix LUN_RESET active TMR descriptor handling
target: Fix LUN_RESET active I/O handling for ACK_KREF
qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM
qla2xxx: Fix warning reported by static checker
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
|
|
Export fetch_or() that's implemented and used internally by the
scheduler. We are going to use it for NO_HZ so make it generally
available.
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
Conflicts:
kernel/locking/lockdep.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Merge fixes from Andrew Morton:
"10 fixes"
The lockdep hlist conversion is in the locking tree too, waiting for the
next merge window. Andrew thought it should go in now. I'll take it,
since it fixes a real problem and looks trivially correct (famous last
words).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/x86/Kconfig: CONFIG_X86_UV should depend on CONFIG_EFI
mm: fix pfn_t vs highmem
kernel/locking/lockdep.c: convert hash tables to hlists
mm,thp: fix spellos in describing __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
mm,thp: khugepaged: call pte flush at the time of collapse
mm/backing-dev.c: fix error path in wb_init()
mm, dax: check for pmd_none() after split_huge_pmd()
vsprintf: kptr_restrict is okay in IRQ when 2
mm: fix filemap.c kernel doc warning
ubsan: cosmetic fix to Kconfig text
|
|
As of commit 876fe76d793d03077eb61ba3afab4a383f46c554
"mtd: maps: physmap: Add reference counter to set_vpp()"
the comment in the header file is incorrect and misleading.
Fix it up.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Parsons <lost.distance@yahoo.com>
Fixes: 876fe76d793d ("mtd: maps: physmap: Add reference counter to set_vpp()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of seven fixes:
Two regressions in the new hisi_sas arm driver, a blacklist entry for
the marvell console which was causing a reset cascade without it, a
race fix in the WRITE_SAME/DISCARD routines, a retry fix for the rdac
driver, without which, it would prematurely return EIO and a couple of
fixes for the hyper-v storvsc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
block/sd: Return -EREMOTEIO when WRITE SAME and DISCARD are disabled
SCSI: Add Marvell Console to VPD blacklist
scsi_dh_rdac: always retry MODE SELECT on command lock violation
storvsc: Use the specified target ID in device lookup
storvsc: Install the storvsc specific timeout handler for FC devices
hisi_sas: fix v1 hw check for slot error
hisi_sas: add dependency for HAS_IOMEM
|
|
The userspace might need some sort of cache coherency management e.g. when CPU
and GPU domains are being accessed through dma-buf at the same time. To
circumvent this problem there are begin/end coherency markers, that forward
directly to existing dma-buf device drivers vfunc hooks. Userspace can make use
of those markers through the DMA_BUF_IOCTL_SYNC ioctl. The sequence would be
used like following:
- mmap dma-buf fd
- for each drawing/upload cycle in CPU 1. SYNC_START ioctl, 2. read/write
to mmap area 3. SYNC_END ioctl. This can be repeated as often as you
want (with the new data being consumed by the GPU or say scanout device)
- munmap once you don't need the buffer any more
v2 (Tiago): Fix header file type names (u64 -> __u64)
v3 (Tiago): Add documentation. Use enum dma_buf_sync_flags to the begin/end
dma-buf functions. Check for overflows in start/length.
v4 (Tiago): use 2d regions for sync.
v5 (Tiago): forget about 2d regions (v4); use _IOW in DMA_BUF_IOCTL_SYNC and
remove range information from struct dma_buf_sync.
v6 (Tiago): use __u64 structured padded flags instead enum. Adjust
documentation about the recommendation on using sync ioctls.
v7 (Tiago): Alex' nit on flags definition and being even more wording in the
doc about sync usage.
v9 (Tiago): remove useless is_dma_buf_file check. Fix sync.flags conditionals
and its mask order check. Add <linux/types.h> include in dma-buf.h.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Tiago Vignatti <tiago.vignatti@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455228291-29640-1-git-send-email-tiago.vignatti@intel.com
|
|
Backmerge to get at the new encoder_mask support in atomic helpers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This module is heavily based on i2c-dev. Once loaded, it provides one
dev node per DP AUX channel, named drm_dp_auxN, where N is an integer.
It's possible to know which connector owns this aux channel by looking
at the respective sysfs /sys/class/drm_aux_dev/drm_dp_auxN/connector, if
the connector device pointer was correctly set in the aux helper struct.
Two main operations are provided on the registers read and write. The
address of the register to be read or written is given using lseek. The
seek position is updated upon read or write.
v2:
- lseek is used to select the register to read/write
- read/write are used instead of ioctl
- no blocking_notifier is used, just a direct callback
v3:
- use drm_dp_aux_dev prefix for public functions
- chardev is named drm_dp_auxN
- read/write don't allocate a buffer anymore, and transfer up to 16 bytes a
time
- remove notifier list from the implementation
- option on menuconfig is now a boolean
- add inline stub functions to avoid breakage when this option is disabled
v4:
- fix build system changes - actually disable this module when not selected.
v5:
- Use kref to avoid device closing while still in use
- Don't use list, use an idr for storing aux_dev
- Remove "connector" attribute
- set aux.dev to the connector drm_connector device, instead of
drm_device
v6:
- Use atomic_t for usage count
- Use a mutex instead of spinlock for idr lock
- Destroy chardev immediately on unregister
- other minor suggestions from Ville
v7:
- style fixes
- error handling fixes
v8:
- more error handling fixes
v9:
- remove module_init and module_exit, and add drm_dp_aux_dev_init/exit
to drm_kms_helper_init/exit.
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453417821-2811-3-git-send-email-rafael.antognolli@intel.com
|
|
The module_init and module_exit functions will start here, and call the
subsequent init's and exit's.
v10:
- Keep __init on drm_fb_helper init function.
- Move MODULE_* macros to the common file.
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453417821-2811-2-git-send-email-rafael.antognolli@intel.com
|
