| Age | Commit message (Collapse) | Author |
|---|
|
wiphy names were recently limited to 128 bytes by commit a7cfebcb7594
("cfg80211: limit wiphy names to 128 bytes"). As it turns out though,
this isn't sufficient because dev_vprintk_emit() needs the syslog header
string "SUBSYSTEM=ieee80211\0DEVICE=+ieee80211:$devname" to fit into 128
bytes. This triggered the "device/subsystem name too long" WARN when
the device name was >= 90 bytes. As before, this was reproduced by
syzbot by sending an HWSIM_CMD_NEW_RADIO command to the MAC80211_HWSIM
generic netlink family.
Fix it by further limiting wiphy names to 64 bytes.
Reported-by: syzbot+e64565577af34b3768dc@syzkaller.appspotmail.com
Fixes: a7cfebcb7594 ("cfg80211: limit wiphy names to 128 bytes")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Version 20180508.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Need to backmerge some nouveau fixes to reduce
the nouveau -next conflicts a lot.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The __dentry_open function was removed in
commit <2a027e7a18738>("fold __dentry_open() into its sole caller").
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.
For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch adds one more generic PHY mode to the phy_mode enum, to allow
configuring generic PHYs to the 2.5G SGMII mode by using the set_mode
callback.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.
I also merged wireless-drivers due to an iwlwifi patch dependency.
Major changes:
iwlwifi
* implement Traffic Condition Monitor and use it for scan, BT coex and
to detect when the AP doesn't support UAPSD properly
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload
qtnfmac
* DFS offload support
rsi
* roaming enhancements
* increase max supported aggregation subframes
* don't advertise 5 GHz support if the device doesn't support it
brcmfmac
* add support for BCM4366E chipset
* add support for bcm43364 wireless chipset
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create and export a new helper tcp_rack_skb_timeout and move tcp_is_rack
to prepare the final RTO change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous approach for the lost and retransmit bits was to
wipe the slate clean: zero all the lost and retransmit bits,
correspondingly zero the lost_out and retrans_out counters, and
then add back the lost bits (and correspondingly increment lost_out).
The new approach is to treat this very much like marking packets
lost in fast recovery. We don’t wipe the slate clean. We just say
that for all packets that were not yet marked sacked or lost, we now
mark them as lost in exactly the same way we do for fast recovery.
This fixes the lost retransmit accounting at RTO time and greatly
simplifies the RTO code by sharing much of the logic with Fast
Recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a rewrite of NewReno loss recovery implementation that is
simpler and standalone for readability and better performance by
using less states.
Note that NewReno refers to RFC6582 as a modification to the fast
recovery algorithm. It is used only if the connection does not
support SACK in Linux. It should not to be confused with the Reno
(AIMD) congestion control.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the classic DUPACK threshold rule
(#DupThresh) in RACK.
When the number of packets SACKed is greater or equal to the
threshold, RACK sets the reordering window to zero which would
immediately mark all the unsacked packets below the highest SACKed
sequence lost. Since this approach is known to not work well with
reordering, RACK only uses it if no reordering has been observed.
The DUPACK threshold rule is a particularly useful extension to the
fast recoveries triggered by RACK reordering timer. For example
data-center transfers where the RTT is much smaller than a timer
tick, or high RTT path where the default RTT/4 may take too long.
Note that this patch differs slightly from RFC6675. RFC6675
considers a packet lost when at least #DupThresh higher-sequence
packets are SACKed.
With RACK, for connections that have seen reordering, RACK
continues to use a dynamically-adaptive time-based reordering
window to detect losses. But for connections on which we have not
yet seen reordering, this patch considers a packet lost when at
least one higher sequence packet is SACKed and the total number
of SACKed packets is at least DupThresh. For example, suppose a
connection has not seen reordering, and sends 10 packets, and
packets 3, 5, 7 are SACKed. RFC6675 considers packets 1 and 2
lost. RACK considers packets 1, 2, 4, 6 lost.
There is some small risk of spurious retransmits here due to
reordering. However, this is mostly limited to the first flight of
a connection on which the sender receives SACKs from reordering.
And RFC 6675 and FACK loss detection have a similar risk on the
first flight with reordering (it's just that the risk of spurious
retransmits from reordering was slightly narrower for those older
algorithms due to the margin of 3*MSS).
Also the minimum reordering window is reduced from 1 msec to 0
to recover quicker on short RTT transfers. Therefore RACK is more
aggressive in marking packets lost during recovery to reduce the
reordering window timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
scatterlist code expects virt_to_page() to work, which fails with
CONFIG_VMAP_STACK=y.
Fixes: c46234ebb4d1e ("tls: RX path for ktls")
Signed-off-by: Matt Mullins <mmullins@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fixes from Paolo Bonzini:
- ARM/ARM64 locking fixes
- x86 fixes: PCID, UMIP, locking
- improved support for recent Windows version that have a 2048 Hz APIC
timer
- rename KVM_HINTS_DEDICATED CPUID bit to KVM_HINTS_REALTIME
- better behaved selftests
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: rename KVM_HINTS_DEDICATED to KVM_HINTS_REALTIME
KVM: arm/arm64: VGIC/ITS save/restore: protect kvm_read_guest() calls
KVM: arm/arm64: VGIC/ITS: protect kvm_read_guest() calls with SRCU lock
KVM: arm/arm64: VGIC/ITS: Promote irq_lock() in update_affinity
KVM: arm/arm64: Properly protect VGIC locks from IRQs
KVM: X86: Lower the default timer frequency limit to 200us
KVM: vmx: update sec exec controls for UMIP iff emulating UMIP
kvm: x86: Suppress CR3_PCID_INVD bit only when PCIDs are enabled
KVM: selftests: exit with 0 status code when tests cannot be run
KVM: hyperv: idr_find needs RCU protection
x86: Delay skip of emulated hypercall instruction
KVM: Extend MAX_IRQ_ROUTES to 4096 for all archs
|
|
After the previous patch, for NOLOCK qdiscs, q->seqlock is
always held when the dequeue() is invoked, we can drop
any additional locking to protect such operation.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that we can use lockdep on it.
The newly introduced sequence lock has the same scope of busylock,
so it shares the same lockdep annotation, but it's only used for
NOLOCK qdiscs.
With this changeset we acquire such lock in the control path around
flushing operation (qdisc reset), to allow more NOLOCK qdisc perf
improvement in the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call ACPI cache parsing routines from base cacheinfo code if ACPI
is enabled. Also stub out cache_setup_acpi and acpi_find_last_cache_level
so that individual architectures can enable ACPI topology parsing.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
ACPI 6.2 adds a new table, which describes how processing units
are related to each other in tree like fashion. Caches are
also sprinkled throughout the tree and describe the properties
of the caches in relation to other caches and processing units.
Add the code to parse the cache hierarchy and report the total
number of levels of cache for a given core using
acpi_find_last_cache_level() as well as fill out the individual
cores cache information with cache_setup_acpi() once the
cpu_cacheinfo structure has been populated by the arch specific
code.
An additional patch later in the set adds the ability to report
peers in the topology using find_acpi_cpu_topology()
to report a unique ID for each processing unit at a given level
in the tree. These unique id's can then be used to match related
processing units which exist as threads, within a given
package, etc.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Rename and change the type of of_node to indicate
it is a generic pointer which is generally only used
for comparison purposes. In a later patch we will put
an ACPI/PPTT token pointer in fw_token so that
the code which builds the shared cpu masks can be reused.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Vijaya Kumar K <vkilari@codeaurora.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
proc_pid_cmdline_read() and environ_read() directly access the target
process' VM to retrieve the command line and environment. If this
process remaps these areas onto a file via mmap(), the requesting
process may experience various issues such as extra delays if the
underlying device is slow to respond.
Let's simply refuse to access file-backed areas in these functions.
For this we add a new FOLL_ANON gup flag that is passed to all calls
to access_remote_vm(). The code already takes care of such failures
(including unmapped areas). Accesses via /proc/pid/mem were not
changed though.
This was assigned CVE-2018-1120.
Note for stable backports: the patch may apply to kernels prior to 4.11
but silently miss one location; it must be checked that no call to
access_remote_vm() keeps zero as the last argument.
Reported-by: Qualys Security Advisory <qsa@qualys.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added content_type property to drm_connector_state
in order to properly handle external HDMI TV content-type setting.
v2:
* Moved helper function which attaches content type property
to the drm core, as was suggested.
Removed redundant connector state initialization.
v3:
* Removed caps in drm_content_type_enum_list.
After some discussion it turned out that HDMI Spec 1.4
was wrongly assuming that IT Content(itc) bit doesn't affect
Content type states, however itc bit needs to be manupulated
as well. In order to not expose additional property for itc,
for sake of simplicity it was decided to bind those together
in same "content type" property.
v4:
* Added it_content checking in intel_digital_connector_atomic_check.
Fixed documentation for new content type enum.
v5:
* Moved patch revision's description to commit messages.
v6:
* Minor naming fix for the content type enumeration string.
v7:
* Fix parameter name for documentation and parameter alignment
in order not to get warning. Added Content Type description to
new HDMI connector properties section.
v8:
* Thrown away unneeded numbers from HDMI content-type property
description. Switch to strings desription instead of plain
definitions.
v9:
* Moved away hdmi specific content-type enum from
drm_connector_state. Content type property should probably not
be bound to any specific connector interface in
drm_connector_state.
Same probably should be done to hdmi_picture_aspect_ration enum
which is also contained in drm_connector_state. Added special
helper function to get derive hdmi specific relevant infoframe
fields.
v10:
* Added usage description to HDMI properties kernel doc.
v11:
* Created centralized function for filling HDMI AVI infoframe, based
on correspondent DRM property value.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180515135928.31092-2-stanislav.lisovskiy@intel.com
[vsyrjala: clean up checkpatch multiple blank lines warnings]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Minor fixes detected with "scripts/checkpatch.pl --strict"
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180515203736.9224-1-philippe.cornu@st.com
|
|
Add vega20 to amd_asic_type enum and amdgpu_asic_name[].
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
|
|
There are no platform_data users anymore. Move the structs into the
driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
KEEP more tables, and add the function/data section wildcard to more
section selections.
This is a little ad-hoc at the moment, but kernel code should be moved
to consistently use .text..x (note: double dots) for explicit sections
and all references to it in the linker script can be made with
TEXT_MAIN, and similarly for other sections.
For now, let's see if major architectures move to enabling this option
then we can do some refactoring passes. Otherwise if it remains unused
or superseded by LTO, this may not be required.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Now that VMLINUX_SYMBOL() is no-op, clean up the linker script.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
|
|
CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX was selected by BLACKFIN, METAG.
They were removed by commit 4ba66a976072 ("arch: remove blackfin port"),
commit bb6fb6dfcc17 ("metag: Remove arch/metag/"), respectively.
No more architecture enables CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX.
Clean up the export.h headers. I am keeping VMLINUX_SYMBOL() and
VMLINUX_SYMBOL_STR() because they are widely used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
|
|
This patch creates new attributes to accept a map as argument and
then perform the lookup with the generated hash accordingly.
Both current hash functions are supported: Jenkins and Symmetric Hash.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Stephen Rothwell says:
today's linux-next build (x86_64 allmodconfig) produced this warning:
./usr/include/linux/netfilter/nf_osf.h:25: found __[us]{8,16,32,64} type without #include <linux/types.h>
Fix that up and also move kernel-private struct out of uapi (it was not
exposed in any released kernel version).
tested via allmodconfig build + make headers_check.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: bfb15f2a95cb ("netfilter: extract Passive OS fingerprint infrastructure from xt_osf")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Commit 318a19718261 (device property: refactor built-in properties
support) went way too far and brought a union aliasing. Partially
revert it here to get rid of union aliasing.
Note, all Apple properties are considered as u8 arrays. To get a value
of any of them the caller must use device_property_read_u8_array().
What's union aliasing?
~~~~~~~~~~~~~~~~~~~~~~
The C99 standard in section 6.2.5 paragraph 20 defines union type as
"an overlapping nonempty set of member objects". It also states in
section 6.7.2.1 paragraph 14 that "the value of at most one of the
members can be stored in a union object at any time'.
Union aliasing is a type punning mechanism using union members to store
as one type and read back as another.
Why it's not good?
~~~~~~~~~~~~~~~~~~
Section 6.2.6.1 paragraph 6 says that a union object may not be a trap
representation, although its member objects may be.
Meanwhile annex J.1 says that "the value of a union member other than
the last one stored into" is unspecified [removed in C11].
In TC3, a footnote is added which specifies that accessing a member of a
union other than the last one stored causes "the object representation"
to be re-interpreted in the new type and specifically refers to this as
"type punning". This conflicts to some degree with Annex J.1.
While it's working in Linux with GCC, the use of union members to do
type punning is not clear area in the C standard and might lead to
unspecified behaviour.
More information is available in this [1] blog post.
[1]: https://davmac.wordpress.com/2010/02/26/c99-revisited/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Stoney SoC provides oscout clock. This clock can support 25Mhz and
48Mhz of frequency.
The clock is available for general system use.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a parameter (in the form of a structure to ease future API
extensions) to the VSP atomic flush handler to pass CRC source
configuration, and pass the CRC value to the completion callback.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The structure is used in the API that the VSP1 driver exposes to the DU
driver. Documenting it is thus important.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d48461deacc57c07ed86d9915e5aa4b3539
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Add new structure "coupling_desc" to regulator_dev, which contains
pointers to all coupled regulators including the owner of the structure,
number of coupled regulators and counter of currently resolved
regulators.
Add of_functions to parse all data needed in regulator coupling.
Provide method to check DTS data consistency. Check if each coupled
regulator's max_spread is equal and if their lists of regulators match.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setting voltage, enabling/disabling regulators requires operations on
all regulators related with the regulator being changed. Therefore,
all of them should be locked for the whole operation. With the current
locking implementation, adding additional dependency (regulators
coupling) causes deadlocks in some cases.
Introduce a possibility to attempt to lock a mutex multiple times
by the same task without waiting on a mutex. This should handle all
reasonable coupling-supplying combinations, especially when two coupled
regulators share common supplies. The only situation that should be
forbidden is simultaneous coupling and supplying between a pair of
regulators.
The idea is based on clk core.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
We have augmented the GPIO core to look up the regulator special
GPIO "wlf,ldoena" in commit 6a537d48461d
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 289ca025ee1d ("ALSA: Use priority list for managing device
list") changed the way to register/disconnect/free devices via a
single priority list. This helped to make behavior consistent, but it
also changed a slight behavior change: namely, the control device is
registered earlier than others, while it was supposed to be the very
last one.
I've put SNDRV_DEV_CONTROL in the current position as the release of
ctl elements often conflict with the private ctl elements some PCM or
other components may create, which often leads to a double-free.
But, the order of register and disconnect should be indeed fixed as
expected in the early days: the control device gets registered at
last, and disconnected at first.
This patch changes the priority list order to move SNDRV_DEV_CONTROL
as the last guy to assure the register / disconnect order. Meanwhile,
for keeping the messy resource release order, manually treat the
control and lowlevel devices as last freed one.
Additional note:
The lowlevel device is the device where a card driver creates at
probe. And, we still keep the release order control -> lowlevel, as
there might be link from a control element back to a lowlevel object.
Fixes: 289ca025ee1d ("ALSA: Use priority list for managing device list")
Reported-by: Tzung-Bi Shih <tzungbi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Regulators attached via RPMh on Qualcomm sdm845 apparently are
write-only. Specifically you can send a request for a certain voltage
but you can't read back to see what voltage you've requested. What
this means is that at bootup we have absolutely no idea what voltage
we could be at.
As discussed in the patches to try to support the RPMh regulators [1],
the fact that regulators are write-only means that its driver's
get_voltage_sel() should return an error code if it's called before
any calls to set_voltage_sel(). This causes problems in
machine_constraints_voltage() when trying to apply the constraints.
A proposed fix was to come up with an error code that could be
returned by get_voltage_sel() which would cause the regulator
framework to simply try setting the voltage with the current
constraints.
In this patch I propose the error code -ENOTRECOVERABLE. In errno.h
this error is described as "State not recoverable". Though the error
code was originally intended "for robust mutexes", the description of
the error code seems to apply here because we can't read the state of
the regulator. Also note that the only existing user of this error
code in the regulator framework is tps65090-regulator.c which returns
this error code from the enable() call (not get_voltage() or
get_voltage_sel()), so there should be no existing regulators that
might accidentally get the new behavior. (Side note is that tps65090
seems to interpret this error code to mean an error that you can't
recover from rather than some data that can't be recovered).
[1] https://patchwork.kernel.org/patch/10340897/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch reports the device's capbilities to offload
encapsulated MPLS tunnel protocols to user-space:
- Capability to offload MPLS over GRE.
- Capability to offload MPLS over UDP.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
