| Age | Commit message (Collapse) | Author |
|---|
|
This patch is to remove the typedef sctp_unrecognized_param_t, and
replace with struct sctp_unrecognized_param in the places where it's
using this typedef.
It is also to fix some indents in sctp_sf_do_unexpected_init() and
sctp_sf_do_5_1B_init().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to remove the typedef sctp_cookie_param_t, and
replace with struct sctp_cookie_param in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to remove the typedef sctp_initack_chunk_t, and
replace with struct sctp_initack_chunk in the places where it's
using this typedef.
It is also to use sizeof(variable) instead of sizeof(type).
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the device interrupts disabling and enabling as well as
cpuidle_pause() and cpuidle_resume() called during the "noirq"
stages of system suspend into separate functions to allow the
core suspend-to-idle code to be optimized (later).
The only functional difference this makes is that debug facilities
and diagnostic tools will not include the above operations into the
"noirq" device suspend/resume duration measurements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds support to calculate the time spent by the generic
power domains in on and various idle states.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This adds a new NETDEV_UDP_TUNNEL_DROP_INFO event, similar to
NETDEV_UDP_TUNNEL_PUSH_INFO, to signal to un-offload ports.
This also adds udp_tunnel_drop_rx_port(), which calls
ndo_udp_tunnel_del.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a new netdevice feature, so that the offloading of RX port for
UDP tunnels can be disabled by the administrator on some netdevices,
using the "rx-udp_tunnel-port-offload" feature in ethtool.
This feature is set for all devices that provide ndo_udp_tunnel_add.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sparse complains about wrong address space used in __acpi_map_table()
and in __acpi_unmap_table().
arch/x86/kernel/acpi/boot.c:127:29: warning: incorrect type in return expression (different address spaces)
arch/x86/kernel/acpi/boot.c:127:29: expected char *
arch/x86/kernel/acpi/boot.c:127:29: got void [noderef] <asn:2>*
arch/x86/kernel/acpi/boot.c:135:23: warning: incorrect type in argument 1 (different address spaces)
arch/x86/kernel/acpi/boot.c:135:23: expected void [noderef] <asn:2>*addr
arch/x86/kernel/acpi/boot.c:135:23: got char *map
Correct address space to be in align of type of returned and passed
parameter.
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Right now if a file includes acpi_numa.h and they don't happen to include
linux/numa.h before it, they get the following warning:
./include/acpi/acpi_numa.h:9:5: warning: "MAX_NUMNODES" is not defined [-Wundef]
#if MAX_NUMNODES > 256
^~~~~~~~~~~~
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Today sending a signal with rt_sigqueueinfo and receving it on
a signalfd does not work reliably. The issue is that reading
a signalfd instead of returning a siginfo returns a signalfd_siginfo and
the kernel must convert from one to the other.
The kernel does not currently have the code to deduce which union
members of struct siginfo are in use.
In this patchset I fix that by introducing a new function siginfo_layout
that can look at a siginfo and report which union member of struct
siginfo is in use. Before that I clean up how we populate struct
siginfo.
The siginfo structure has two key members si_signo and si_code. Some
si_codes are signal specific and for those it takes si_signo and si_code
to indicate the members of siginfo that are valid. The rest of the
si_code values are signal independent like SI_USER, SI_KERNEL, SI_QUEUE,
and SI_TIMER and only si_code is needed to indicate which members of
siginfo are valid.
At least that is how POSIX documents them, and how common sense would
indicate they should function. In practice we have been rather sloppy
about maintaining the ABI in linux and we have some exceptions. We have
a couple of buggy architectures that make SI_USER mean something
different when combined with SIGFPE or SIGTRAP. Worse we have
fcntl(F_SETSIG) which results in the si_codes POLL_IN, POLL_OUT,
POLL_MSG, POLL_ERR, POLL_PRI, POLL_HUP being sent with any arbitrary
signal, while the values are in a range that overlaps the signal
specific si_codes.
Thankfully the ambiguous cases with the POLL_NNN si_codes are for
things no sane persion would do that so we can rectify the situtation.
AKA no one cares so we won't cause a regression fixing it.
As part of fixing this I stop leaking the __SI_xxxx codes to userspace
and stop storing them in the high 16bits of si_code. Making the kernel
code fundamentally simpler. We have already confirmed that the one
application that would see this difference in kernel behavior CRIU won't
be affected by this change as it copies values verbatim from one kernel
interface to another.
v3:
- Corrected the patches so they bisect properly
v2:
- Benchmarked the code to confirm no performance changes are visible.
- Reworked the first couple of patches so that TRAP_FIXME and
FPE_FIXME are not exported to userspace.
- Rebased on top of the siginfo cleanup that came in v4.13-rc1
- Updated alpha to use both TRAP_FIXME and FPE_FIXME
Eric W. Biederman (7):
signal/alpha: Document a conflict with SI_USER for SIGTRAP
signal/ia64: Document a conflict with SI_USER with SIGFPE
signal/sparc: Document a conflict with SI_USER with SIGFPE
signal/mips: Document a conflict with SI_USER with SIGFPE
signal/testing: Don't look for __SI_FAULT in userspace
fcntl: Don't use ambiguous SIG_POLL si_codes
signal: Remove kernel interal si_code magic
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
struct siginfo is a union and the kernel since 2.4 has been hiding a union
tag in the high 16bits of si_code using the values:
__SI_KILL
__SI_TIMER
__SI_POLL
__SI_FAULT
__SI_CHLD
__SI_RT
__SI_MESGQ
__SI_SYS
While this looks plausible on the surface, in practice this situation has
not worked well.
- Injected positive signals are not copied to user space properly
unless they have these magic high bits set.
- Injected positive signals are not reported properly by signalfd
unless they have these magic high bits set.
- These kernel internal values leaked to userspace via ptrace_peek_siginfo
- It was possible to inject these kernel internal values and cause the
the kernel to misbehave.
- Kernel developers got confused and expected these kernel internal values
in userspace in kernel self tests.
- Kernel developers got confused and set si_code to __SI_FAULT which
is SI_USER in userspace which causes userspace to think an ordinary user
sent the signal and that it was not kernel generated.
- The values make it impossible to reorganize the code to transform
siginfo_copy_to_user into a plain copy_to_user. As si_code must
be massaged before being passed to userspace.
So remove these kernel internal si codes and make the kernel code simpler
and more maintainable.
To replace these kernel internal magic si_codes introduce the helper
function siginfo_layout, that takes a signal number and an si_code and
computes which union member of siginfo is being used. Have
siginfo_layout return an enumeration so that gcc will have enough
information to warn if a switch statement does not handle all of union
members.
A couple of architectures have a messed up ABI that defines signal
specific duplications of SI_USER which causes more special cases in
siginfo_layout than I would like. The good news is only problem
architectures pay the cost.
Update all of the code that used the previous magic __SI_ values to
use the new SIL_ values and to call siginfo_layout to get those
values. Escept where not all of the cases are handled remove the
defaults in the switch statements so that if a new case is missed in
the future the lack will show up at compile time.
Modify the code that copies siginfo si_code to userspace to just copy
the value and not cast si_code to a short first. The high bits are no
longer used to hold a magic union member.
Fixup the siginfo header files to stop including the __SI_ values in
their constants and for the headers that were missing it to properly
update the number of si_codes for each signal type.
The fixes to copy_siginfo_from_user32 implementations has the
interesting property that several of them perviously should never have
worked as the __SI_ values they depended up where kernel internal.
With that dependency gone those implementations should work much
better.
The idea of not passing the __SI_ values out to userspace and then
not reinserting them has been tested with criu and criu worked without
changes.
Ref: 2.4.0-test1
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
We have a weird and problematic intersection of features that when
they all come together result in ambiguous siginfo values, that
we can not support properly.
- Supporting fcntl(F_SETSIG,...) with arbitrary valid signals.
- Using positive values for POLL_IN, POLL_OUT, POLL_MSG, ..., etc
that imply they are signal specific si_codes and using the
aforementioned arbitrary signal to deliver them.
- Supporting injection of arbitrary siginfo values for debugging and
checkpoint/restore.
The result is that just looking at siginfo si_codes of 1 to 6 are
ambigious. It could either be a signal specific si_code or it could
be a generic si_code.
For most of the kernel this is a non-issue but for sending signals
with siginfo it is impossible to play back the kernel signals and
get the same result.
Strictly speaking when the si_code was changed from SI_SIGIO to
POLL_IN and friends between 2.2 and 2.4 this functionality was not
ambiguous, as only real time signals were supported. Before 2.4 was
released the kernel began supporting siginfo with non realtime signals
so they could give details of why the signal was sent.
The result is that if F_SETSIG is set to one of the signals with signal
specific si_codes then user space can not know why the signal was sent.
I grepped through a bunch of userspace programs using debian code
search to get a feel for how often people choose a signal that results
in an ambiguous si_code. I only found one program doing so and it was
using SIGCHLD to test the F_SETSIG functionality, and did not appear
to be a real world usage.
Therefore the ambiguity does not appears to be a real world problem in
practice. Remove the ambiguity while introducing the smallest chance
of breakage by changing the si_code to SI_SIGIO when signals with
signal specific si_codes are targeted.
Fixes: v2.3.40 -- Added support for queueing non-rt signals
Fixes: v2.3.21 -- Changed the si_code from SI_SIGIO
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Everything uses uuid_t now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add support to work with a RSS QP by using an indirection table object
upon QP creation. Other related QP verbs (e.g. modify/destroy/query) were
updated as well for that QP mode.
Notes:
- The RX hash properties are supplied as driver private data.
- The RSS QP port is used on the associated WQs in its indirection
table. Applying different ports during WQ life time is not allowed.
- The expected RSS QP flow is: create, modify(RST->INIT),
modify(RST->RTR), destroy.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
To enable RSS functionality the IB indirection table object (i.e.
ib_rwq_ind_table) should be used.
This patch implements the related verbs as of create and destroy an
indirection table.
In downstream patches the indirection table will be used as part of RSS
QP creation.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Support create/modify/destroy WQ related verbs.
The base IB object to enable RSS functionality is a WQ (i.e. ib_wq).
This patch implements the related WQ verbs as of create, modify and
destroy.
In downstream patches the WQ will be used as part of an indirection
table (i.e. ib_rwq_ind_table) to enable RSS QP creation.
Notes:
ConnectX-3 hardware requires consecutive WQNs list as receive descriptor
queues for the RSS QP. Hence, the driver manages consecutive ranges lists
per context which the user must respect.
Destroying the WQ does not return its WQN back to its range for
reusing. However, destroying all WQs from the same range releases the
range and in turn releases its WQNs for reusing.
Since the WQ object is not a natural object in the hardware, the driver
implements the WQ by the hardware QP.
As such, the WQ inherits its port from its RSS QP parent upon its
RST->INIT transition and by that time its state is applied to the
hardware.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Adding visibility of resource usage of QPs, CQs and counters used by
virtual functions. This feature will be used to give the PF administrator
more data while debugging VF status. Usage info was added to ALLOC_RES
command, to notify the PF if the resource which is being reserved or
allocated for the VF will be used by kernel driver or by user verbs.
Updated reservation and allocation functions of QP, CQ and counter with
additional usage parameter.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When inline-receive is enabled, the HCA may write received
data into the receive WQE.
Inline-receive is enabled by setting its matching bit in
the QP context and each single-packet message with payload
not exceeding the receive WQE size will be delivered to
the WQE.
The completion report will indicate that the payload was placed to the WQE.
It includes:
1) Return maximum supported size of inline-receive by the hardware
in query_device vendor's data part.
2) Enable the feature when requested by the vendor data input.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds below requester and responder side error counters,
which will be exposed by hardware counters interface and are supported
as part of query Q counters command extension.
+---------------------------+-------------------------------------+
| Name | Description |
|---------------------------+-------------------------------------|
|resp_local_length_error | Number of times responder detected |
| | local length errors |
|---------------------------+-------------------------------------|
|resp_cqe_error | Number of CQEs completed with error |
| | at responder |
|---------------------------+-------------------------------------|
|req_cqe_error | Number of CQEs completed with error |
| | at requester |
|---------------------------+-------------------------------------|
|req_remote_invalid_request | Number of times requester detected |
| | remote invalid request error |
|---------------------------+-------------------------------------|
|req_remote_access_error | Number of times requester detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_remote_access_error | Number of times responder detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at responder |
|---------------------------+-------------------------------------|
|req_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at requester |
+---------------------------+-------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92ce ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Report 'ipoib_enhanced_offloads' capabilities from
the core layer, it will be used in the next patch from this series.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Enable QP creation with a given source QP number, the created QP will
use the source QPN as its wire QP number.
To create such a QP, root privileges (i.e. CAP_NET_RAW) are required
from the user application.
This comes as a pre-patch for downstream patches in this series to
allow user space applications to accelerate traffic which is typically
handled by IPoIB ULP.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Enable QP creation with a given source QP number.
The created QP will use the source QPN as its wire QP number.
This comes as a pre-patch for downstream patches in this series to
allow user space applications to accelerate traffic which is typically
handled by IPoIB ULP.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
RoCEv2 Annex states that for RoCEv2 over IPv4, the corresponding
IPv4 address is encoded into the GID according to the following rule:
GID= :ffff:<IPv4 address>
Remove the 0xff0e prefix for RoCEv2 packets with IPv4 and leave it
zeroed and change rdma_is_multicast_addr() to consider the new logic.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When delay drop timeout is expired, the firmware raises
general notification event of DELAY_DROP_TIMEOUT subtype.
In addition the feature is disable so the driver have to
reactivate the timeout.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support to SET_DELAY_DROP command.
This command will be used in downstream patches for delay packet drop.
The timeout value should be indicated by delay_drop_timeout field.
Packet processing will be delayed till timeout value passed or until
more WQEs are posted.
Setting this value to 0 disables the feature.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Work queue which is created with IB_WQ_FLAGS_DELAY_DROP won't
cause packet drops when there aren't receive WQEs, but will wait until
posting of receive WQEs or for some period of time that the device
was configured with.
It includes:
* Add a new creation flag to enable delay drop functionality in a WQ.
* A new capability was introduced - IB_RAW_PACKET_CAP_DELAY_DROP, which
is the device's ability to delay packet drops when there aren't receive
WQEs.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When a user sets port_guid, node_guid or policy of an IB virtual
function, save this information in "struct mlx5_vf_context".
This information will be restored later when pci_resume is called.
To make sure this works, one can use aer-inject to generate PCI
errors on mlx5 devices and verify if relevant fields are restored
after PCI resume.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support for raw ethernet local loopback firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Logic of retrieving netdev speed from net_device and translating it to
IB speed is implemented in rxe, in usnic and in bnxt drivers.
Define new function which merges all.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Christian Benvenuti <benve@cisco.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
|
|
This is helpful for 'nft monitor' to track which process caused a given
change to the ruleset.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
These chain counters are only used by the iptables-compat tool, that
allow users to use the x_tables extensions from the existing nf_tables
framework. This patch makes nf_tables by ~5% for the general usecase,
ie. native nft users, where no chain counters are used at all.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Generic header defines xlate_dev_kmem_ptr().
Reuse it from generic header and remove in x86 code.
Move a description to the generic header as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Baolin Wang <baolin.wang@spreadtrum.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-i2c@vger.kernel.org
Cc: wsa@the-dreams.de
Link: http://lkml.kernel.org/r/20170630170934.83028-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Generic header defines memset_io, memcpy_fromio(). and memcpy_toio().
Reuse them from generic header and remove in x86 code.
Move the descriptions to the generic header as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Baolin Wang <baolin.wang@spreadtrum.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-i2c@vger.kernel.org
Cc: wsa@the-dreams.de
Link: http://lkml.kernel.org/r/20170630170934.83028-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
|
|
We want the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the char/misc driver fixes in here as well to handle future
changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When setting up the Xenstore watch for the memory target size the new
watch will fire at once. Don't try to reach the configured target size
by onlining new memory in this case, as the current memory size will
be smaller in almost all cases due to e.g. BIOS reserved pages.
Onlining new memory will lead to more problems e.g. undesired conflicts
with NVMe devices meant to be operated as block devices.
Instead remember the difference between target size and current size
when the watch fires for the first time and apply it to any further
size changes, too.
In order to avoid races between balloon.c and xen-balloon.c init calls
do the xen-balloon.c initialization from balloon.c.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The messages printed by tk_debug_account_sleep_time() are basically
useful for system sleep debugging, so print them only when the other
debug messages from the core suspend/hibernate code are enabled.
While at it, make it clear that the messages from
tk_debug_account_sleep_time() are about timekeeping suspend
duration, because in general timekeeping may be suspeded and
resumed for multiple times during one system suspend-resume cycle.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
huge at all, a revert of a patch that turned out to break things, a
fix up for a new tty ioctl we added in 4.13-rc1 to get the uapi
definition correct, and a few minor serial driver fixes for reported
issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix TIOCGPTPEER ioctl definition
tty: hide unused pty_get_peer function
tty: serial: lpuart: Fix the logic for detecting the 32-bit type UART
serial: imx: Prevent TX buffer PIO write when a DMA has been started
Revert "serial: imx-serial - move DMA buffer configuration to DT"
serial: sh-sci: Uninitialized variables in sysfs files
serial: st-asc: Potential error pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.13-rc2.
The usual batch, gadget fixes for reported issues, as well as xhci
fixes, and a small random collection of other fixes for reported
issues.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
xhci: fix memleak in xhci_run()
usb: xhci: fix spinlock recursion for USB2 test mode
xhci: fix 20000ms port resume timeout
usb: xhci: Issue stop EP command only when the EP state is running
xhci: Bad Ethernet performance plugged in ASM1042A host
xhci: Fix NULL pointer dereference when cleaning up streams for removed host
usb: renesas_usbhs: gadget: disable all eps when the driver stops
usb: renesas_usbhs: fix usbhsc_resume() for !USBHSF_RUNTIME_PWCTRL
usb: gadget: udc: renesas_usb3: protect usb3_ep->started in usb3_start_pipen()
usb: gadget: udc: renesas_usb3: fix zlp transfer by the dmac
usb: gadget: udc: renesas_usb3: fix free size in renesas_usb3_dma_free_prd()
usb: gadget: f_uac2: endianness fixes.
usb: gadget: f_uac1: endianness fixes.
include: usb: audio: specify exact endiannes of descriptors
usb: gadget: udc: start_udc() can be static
usb: dwc2: gadget: On USB RESET reset device address to zero
usb: storage: return on error to avoid a null pointer dereference
usb: typec: include linux/device.h in ucsi.h
USB: cdc-acm: add device-id for quirky printer
usb: dwc3: gadget: only unmap requests from DMA if mapped
...
|
|
This merges the bind_unbind driver core feature into the
driver-core-next branch. bind_unbind is a branch so that others can
pull and work off of it safely.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many drivers create additional driver-specific device attributes when
binding to the device, and providing managed version of
device_create_group() will simplify unbinding and error handling in probe
path for such drivers.
Without managed version driver writers either have to mix manual and
managed resources, which is prone to errors, or open-code this function by
providing a wrapper to device_add_group() and use it with devm_add_action()
or devm_add_action_or_reset().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have helpers that work with NULL terminated array of groups, but many
drivers only create a single supplemental group, and do not want to declare
a group array. Let's provide them with helpers working with a single group.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many drivers create additional driver-specific device attributes when
binding to the device. To avoid them calling SYSFS API directly, let's
export these helpers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are certain touch controllers that may come up in either normal
(application) or boot mode, depending on whether firmware/configuration is
corrupted when they are powered on. In boot mode the kernel does not create
input device instance (because it does not necessarily know the
characteristics of the input device in question).
Another number of controllers does not store firmware in a non-volatile
memory, and they similarly need to have firmware loaded before input device
instance is created. There are also other types of devices with similar
behavior.
There is a desire to be able to trigger firmware loading via udev, but it
has to happen only when driver is bound to a physical device (i2c or spi).
These udev actions can not use ADD events, as those happen too early, so we
are introducing BIND and UNBIND events that are emitted at the right
moment.
Also, many drivers create additional driver-specific device attributes
when binding to the device, to provide userspace with additional controls.
The new events allow userspace to adjust these driver-specific attributes
without worrying that they are not there yet.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Debug messages from the system suspend/hibernation infrastructure can
fill up the entire kernel log buffer in some cases and anyway they
are only useful for debugging. They depend on CONFIG_PM_DEBUG, but
that is set as a rule as some generally useful diagnostic facilities
depend on it too.
For this reason, avoid printing those messages by default, but make
it possible to turn them on as needed with the help of a new sysfs
attribute under /sys/power/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
