| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This documents the possible MLO_PAUSE_* settings which can result from
different combinations of MAC_(A)SYM_PAUSE. Special note is paid to
settings which can result from user configuration (MLO_PAUSE_AN). The
autonegotiation results are more-or-less a direct consequence of IEEE
802.3 Table 28B-2.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To abstract the rmid counters into a helper that returns the number
of bytes counted, architecture specific per-rmid state is needed.
It needs to be possible to reset this hidden state, as the values
may outlive the life of an rmid, or the mount time of the filesystem.
mon_event_read() is called with first = true when an rmid is first
allocated in mkdir_mondata_subdir(). Add resctrl_arch_reset_rmid()
and call it from __mon_event_count()'s rr->first check.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-15-james.morse@arm.com
|
|
kmalloc's API family is critical for mm, with one nature that it will
round up the request size to a fixed one (mostly power of 2). Say
when user requests memory for '2^n + 1' bytes, actually 2^(n+1) bytes
could be allocated, so in worst case, there is around 50% memory
space waste.
The wastage is not a big issue for requests that get allocated/freed
quickly, but may cause problems with objects that have longer life
time.
We've met a kernel boot OOM panic (v5.10), and from the dumped slab
info:
[ 26.062145] kmalloc-2k 814056KB 814056KB
From debug we found there are huge number of 'struct iova_magazine',
whose size is 1032 bytes (1024 + 8), so each allocation will waste
1016 bytes. Though the issue was solved by giving the right (bigger)
size of RAM, it is still nice to optimize the size (either use a
kmalloc friendly size or create a dedicated slab for it).
And from lkml archive, there was another crash kernel OOM case [1]
back in 2019, which seems to be related with the similar slab waste
situation, as the log is similar:
[ 4.332648] iommu: Adding device 0000:20:02.0 to group 16
[ 4.338946] swapper/0 invoked oom-killer: gfp_mask=0x6040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null), order=0, oom_score_adj=0
...
[ 4.857565] kmalloc-2048 59164KB 59164KB
The crash kernel only has 256M memory, and 59M is pretty big here.
(Note: the related code has been changed and optimised in recent
kernel [2], these logs are just picked to demo the problem, also
a patch changing its size to 1024 bytes has been merged)
So add an way to track each kmalloc's memory waste info, and
leverage the existing SLUB debug framework (specifically
SLUB_STORE_USER) to show its call stack of original allocation,
so that user can evaluate the waste situation, identify some hot
spots and optimize accordingly, for a better utilization of memory.
The waste info is integrated into existing interface:
'/sys/kernel/debug/slab/kmalloc-xx/alloc_traces', one example of
'kmalloc-4k' after boot is:
126 ixgbe_alloc_q_vector+0xbe/0x830 [ixgbe] waste=233856/1856 age=280763/281414/282065 pid=1330 cpus=32 nodes=1
__kmem_cache_alloc_node+0x11f/0x4e0
__kmalloc_node+0x4e/0x140
ixgbe_alloc_q_vector+0xbe/0x830 [ixgbe]
ixgbe_init_interrupt_scheme+0x2ae/0xc90 [ixgbe]
ixgbe_probe+0x165f/0x1d20 [ixgbe]
local_pci_probe+0x78/0xc0
work_for_cpu_fn+0x26/0x40
...
which means in 'kmalloc-4k' slab, there are 126 requests of
2240 bytes which got a 4KB space (wasting 1856 bytes each
and 233856 bytes in total), from ixgbe_alloc_q_vector().
And when system starts some real workload like multiple docker
instances, there could are more severe waste.
[1]. https://lkml.org/lkml/2019/8/12/266
[2]. https://lore.kernel.org/lkml/2920df89-9975-5785-f79b-257d3052dfaf@huawei.com/
[Thanks Hyeonggon for pointing out several bugs about sorting/format]
[Thanks Vlastimil for suggesting way to reduce memory usage of
orig_size and keep it only for kmalloc objects]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
protection
Add ifc bits related to advanced steering operations (ASO) and general
object modify for macsec to use as part of offloading EPN and replay
protection features.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix ifc fields name to be consistent with the device spec document.
Fixes: 8385c51ff5bc ("net/mlx5: Introduce MACsec Connect-X offload hardware bits and structures")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The walk implementation of most qdisc class modules is basically the
same. That is, the values of count and skip are checked first. If
count is greater than or equal to skip, the registered fn function is
executed. Otherwise, increase the value of count. So we can reconstruct
them.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce cipher sizes descriptor. It helps reducing the amount of code
duplications and repeated switch/cases that assigns the proper sizes
according to the cipher type.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of fixes for fixes for the soc tree:
- A fix for the interrupt number on at91/lan966 ethernet PHYs
- A second round of fixes for NXP i.MX series, including a couple of
build issues, and board specific DT corrections on TQMa8MPQL,
imx8mp-venice-gw74xx and imx8mm-verdin for reliability and
partially broken functionality
- Several fixes for Rockchip SoCs, addressing a USB issue on
BPI-R2-Pro, wakeup on Gru-Bob and reliability of high-speed SD
cards, among other minor issues
- A fix for a long-running naming mistake that prevented the moxart
mmc driver from working at all
- Multiple Arm SCMI firmware fixes for hardening some corner cases"
* tag 'soc-fixes-6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
arm64: dts: imx8mp-venice-gw74xx: fix port/phy validation
ARM: dts: lan966x: Fix the interrupt number for internal PHYs
arm64: dts: imx8mp-venice-gw74xx: fix ksz9477 cpu port
arm64: dts: imx8mp-venice-gw74xx: fix CAN STBY polarity
dt-bindings: memory-controllers: fsl,imx8m-ddrc: drop Leonard Crestez
arm64: dts: tqma8mqml: Include phy-imx8-pcie.h header
arm64: defconfig: enable ARCH_NXP
arm64: dts: imx8mp-tqma8mpql-mba8mpxl: add missing pinctrl for RTC alarm
ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
arm64: dts: imx8mm-verdin: extend pmic voltages
arm64: dts: rockchip: Remove 'enable-active-low' from rk3566-quartz64-a
arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
arm64: dts: rockchip: fix property for usb2 phy supply on rk3568-evb1-v10
arm64: dts: rockchip: fix property for usb2 phy supply on rock-3a
arm64: dts: imx8ulp: add #reset-cells for pcc
arm64: dts: tqma8mpxl-ba8mpxl: Fix button GPIOs
arm64: dts: imx8mn: remove GPU power domain reset
arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
arm64: dts: imx8mm: Reverse CPLD_Dn GPIO label mapping on MX8Menlo
arm64: dts: rockchip: fix upper usb port on BPI-R2-Pro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wifi, netfilter and can.
A handful of awaited fixes here - revert of the FEC changes, bluetooth
fix, fixes for iwlwifi spew.
We added a warning in PHY/MDIO code which is triggering on a couple of
platforms in a false-positive-ish way. If we can't iron that out over
the week we'll drop it and re-add for 6.1.
I've added a new "follow up fixes" section for fixes to fixes in
6.0-rcs but it may actually give the false impression that those are
problematic or that more testing time would have caught them. So
likely a one time thing.
Follow up fixes:
- nf_tables_addchain: fix nft_counters_enabled underflow
- ebtables: fix memory leak when blob is malformed
- nf_ct_ftp: fix deadlock when nat rewrite is needed
Current release - regressions:
- Revert "fec: Restart PPS after link state change" and the related
"net: fec: Use a spinlock to guard `fep->ptp_clk_on`"
- Bluetooth: fix HCIGETDEVINFO regression
- wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2
- mptcp: fix fwd memory accounting on coalesce
- rwlock removal fall out:
- ipmr: always call ip{,6}_mr_forward() from RCU read-side
critical section
- ipv6: fix crash when IPv6 is administratively disabled
- tcp: read multiple skbs in tcp_read_skb()
- mdio_bus_phy_resume state warning fallout:
- eth: ravb: fix PHY state warning splat during system resume
- eth: sh_eth: fix PHY state warning splat during system resume
Current release - new code bugs:
- wifi: iwlwifi: don't spam logs with NSS>2 messages
- eth: mtk_eth_soc: enable XDP support just for MT7986 SoC
Previous releases - regressions:
- bonding: fix NULL deref in bond_rr_gen_slave_id
- wifi: iwlwifi: mark IWLMEI as broken
Previous releases - always broken:
- nf_conntrack helpers:
- irc: tighten matching on DCC message
- sip: fix ct_sip_walk_headers
- osf: fix possible bogus match in nf_osf_find()
- ipvlan: fix out-of-bound bugs caused by unset skb->mac_header
- core: fix flow symmetric hash
- bonding, team: unsync device addresses on ndo_stop
- phy: micrel: fix shared interrupt on LAN8814"
* tag 'net-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
selftests: forwarding: add shebang for sch_red.sh
bnxt: prevent skb UAF after handing over to PTP worker
net: marvell: Fix refcounting bugs in prestera_port_sfp_bind()
net: sched: fix possible refcount leak in tc_new_tfilter()
net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
udp: Use WARN_ON_ONCE() in udp_read_skb()
selftests: bonding: cause oops in bond_rr_gen_slave_id
bonding: fix NULL deref in bond_rr_gen_slave_id
net: phy: micrel: fix shared interrupt on LAN8814
net/smc: Stop the CLC flow if no link to map buffers on
ice: Fix ice_xdp_xmit() when XDP TX queue number is not sufficient
net: atlantic: fix potential memory leak in aq_ndev_close()
can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported
can: gs_usb: gs_can_open(): fix race dev->can.state condition
can: flexcan: flexcan_mailbox_read() fix return value for drop = true
net: sh_eth: Fix PHY state warning splat during system resume
net: ravb: Fix PHY state warning splat during system resume
netfilter: nf_ct_ftp: fix deadlock when nat rewrite is needed
netfilter: ebtables: fix memory leak when blob is malformed
netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
...
|
|
- Misc fixes and improvements to the R-Car DU driver
- Synopsys DW HDMI bridge DT bindings update
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YxkL+tRI8uXDCvj9@pendragon.ideasonboard.com
|
|
update_mba_bw() calculates a new control value for the MBA resource
based on the user provided mbps_val and the current measured
bandwidth. Some control values need remapping by delay_bw_map().
It does this by calling wrmsrl() directly. This needs splitting
up to be done by an architecture specific helper, so that the
remainder can eventually be moved to /fs/.
Add resctrl_arch_update_one() to apply one configuration value
to the provided resource and domain. This avoids the staging
and cross-calling that is only needed with changes made by
user-space. delay_bw_map() moves to be part of the arch code,
to maintain the 'percentage control' view of MBA resources
in resctrl.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-12-james.morse@arm.com
|
|
To support resctrl's MBA software controller, the architecture must provide
a second configuration array to hold the mbps_val[] from user-space.
This complicates the interface between the architecture specific code and
the filesystem portions of resctrl that will move to /fs/, to allow
multiple architectures to support resctrl.
Make the filesystem parts of resctrl create an array for the mba_sc
values. The software controller can be changed to use this, allowing
the architecture code to only consider the values configured in hardware.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-9-james.morse@arm.com
|
|
The flag for need_wakeup is not set for xsks with `XDP_SHARED_UMEM`
flag and of different queue ids and/or devices. They should inherit
the flag from the first socket buffer pool since no flags can be
specified once `XDP_SHARED_UMEM` is specified.
Fixes: b5aea28dca134 ("xsk: Add shared umem support between queue ids")
Signed-off-by: Jalal Mostafa <jalal.a.mostapha@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220921135701.10199-1-jalal.a.mostapha@gmail.com
|
|
Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set
If the IRQ hasn't been set up yet, the UART will have zeroes in its MSI
address/data registers. Disabling the IRQ at the interrupt controller
won't stop the UART from performing a DMA write to the address programmed
in its MSI address register (zero) when it wants to signal an interrupt.
The UARTs (in Ice Lake-D) implement PCI 2.1 style MSI without masking
capability, so there is no way to mask the interrupt at the source PCI
function level, except disabling the MSI capability entirely, but that
would cause it to fall back to INTx# assertion, and the PCI specification
prohibits disabling the MSI capability as a way to mask a function's
interrupt service request.
The MSI address register is zeroed by the hangup as the irq is freed.
The interrupt is signalled during serial8250_do_startup() performing a
THRE test that temporarily toggles THRI in IER. The THRE test currently
occurs before UART's irq (and MSI address) is properly set up.
Refactor serial8250_do_startup() such that irq is set up before the
THRE test. The current irq setup code is intermixed with the timer
setup code. As THRE test must be performed prior to the timer setup,
extract it into own function and call it only after the THRE test.
The ->setup_timer() needs to be part of the struct uart_8250_ops in
order to not create circular dependency between 8250 and 8250_base
modules.
Fixes: 40b36daad0ac ("[PATCH] 8250 UART backup timer")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Lennert Buytenhek <buytenh@arista.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922070005.2965-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use BIT_ULL rather than encoding bits explicitly where applicable with
UART port flags. This makes a (__force upf_t) cast redundant, but keep
it for visual consistency with the flags defined in terms of userspace
macros.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209210007030.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A SERIAL_8250_16550A_VARIANTS configuration option has been recently
defined that lets one request the 8250 driver not to probe for 16550A
device features so as to reduce the driver's device startup time in
virtual machines.
Some actual hardware devices require these features to have been fully
determined however for their driver to work correctly, so define a flag
to let drivers request full 16550A feature probing on a device-by-device
basis if required regardless of the SERIAL_8250_16550A_VARIANTS option
setting chosen.
Fixes: dc56ecb81a0a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable@vger.kernel.org # v5.6+
Reported-by: Anders Blomdell <anders.blomdell@control.lth.se>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209202357520.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to Greg, in the context of magic numbers as defined in
magic-number.rst, "the tty layer should not need this and I'll gladly
take patches"
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Ref: https://lore.kernel.org/linux-doc/YyMlovoskUcHLEb7@kroah.com/
Link: https://lore.kernel.org/r/723478a270a3858f27843cbec621df4d5d44efcc.1663288066.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to Greg, in the context of magic numbers as defined in
magic-number.rst, "the tty layer should not need this and I'll gladly
take patches"
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Ref: https://lore.kernel.org/linux-doc/YyMlovoskUcHLEb7@kroah.com/
Link: https://lore.kernel.org/r/476d024cd6b04160a5de381ea2b9856b60088cbd.1663288066.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The uvc_format_desc, GUID defines and the uvc_format_by_guid helper is
also useful for the uvc gadget stack. This patch moves them to a common
header.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The functions uvc_simplify_fraction and uvc_fraction_to_interval are
generic helpers which are also useful for other v4l2 drivers. This patch
moves them to v4l2-common.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Because domains are exposed to user-space via resctrl, the filesystem
must update its state when CPU hotplug callbacks are triggered.
Some of this work is common to any architecture that would support
resctrl, but the work is tied up with the architecture code to
free the memory.
Move the monitor subdir removal and the cancelling of the mbm/limbo
works into a new resctrl_offline_domain() call. These bits are not
specific to the architecture. Grouping them in one function allows
that code to be moved to /fs/ and re-used by another architecture.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-6-james.morse@arm.com
|
|
Because domains are exposed to user-space via resctrl, the filesystem
must update its state when CPU hotplug callbacks are triggered.
Some of this work is common to any architecture that would support
resctrl, but the work is tied up with the architecture code to
allocate the memory.
Move domain_setup_mon_state(), the monitor subdir creation call and the
mbm/limbo workers into a new resctrl_online_domain() call. These bits
are not specific to the architecture. Grouping them in one function
allows that code to be moved to /fs/ and re-used by another architecture.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-4-james.morse@arm.com
|
|
Other than pcie bus, introduce support for axi bus to mtk wed driver.
Axi bus is used to connect mt7986-wmac soc chip available on mt7986
device.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce Wireless Etherne Dispatcher support on transmission side
for mt7986 chipset
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
mon_enabled and mon_capable are always set as a pair by
rdt_get_mon_l3_config().
There is no point having two values.
Merge them together.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-3-james.morse@arm.com
|
|
rdt_resources_all[] used to have extra entries for L2CODE/L2DATA.
These were hidden from resctrl by the alloc_enabled value.
Now that the L2/L2CODE/L2DATA resources have been merged together,
alloc_enabled doesn't mean anything, it always has the same value as
alloc_capable which indicates allocation is supported by this resource.
Remove alloc_enabled and its helpers.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220902154829.30399-2-james.morse@arm.com
|
|
Per discussion on the alsa-devel mailing list [1], the legacy PIN to PCM
device mapping is obsolete nowadays. The maximum number of the simultaneously
usable PCM devices is equal to the HDMI codec converters.
Remove the extra PCM devices (beyond the detected converters) and force
the use of the dynamic PCM device allocation. The legacy code is removed.
I believe that all HDMI codecs have the jack sensing feature. Move the check
to the codec probe function and print a warning, if a codec without this
feature is detected.
[1] https://lore.kernel.org/alsa-devel/2f37e0b2-1e82-8c0b-2bbd-1e5038d6ecc6@perex.cz/
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220922084017.25925-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The member documentation comment lines for struct counter_comp extend
past the 80-characters column boundary due to extra identation at the
start of each section. This patch realigns the comment block within the
80-characters boundary by removing these superfluous indents.
Reviewed-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20220902120839.4260-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/8294b04153c33602e9c3dd21ac90c1e99bd0fdaf.1663844776.git.william.gray@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As PAGE_SIZE is unsigned long, -1 > PAGE_SIZE when NR_CPUS <= 3.
This leads to very large file sizes:
topology$ ls -l
total 0
-r--r--r-- 1 root root 18446744073709551615 Sep 5 11:59 core_cpus
-r--r--r-- 1 root root 4096 Sep 5 11:59 core_cpus_list
-r--r--r-- 1 root root 4096 Sep 5 10:58 core_id
-r--r--r-- 1 root root 18446744073709551615 Sep 5 10:10 core_siblings
-r--r--r-- 1 root root 4096 Sep 5 11:59 core_siblings_list
-r--r--r-- 1 root root 18446744073709551615 Sep 5 11:59 die_cpus
-r--r--r-- 1 root root 4096 Sep 5 11:59 die_cpus_list
-r--r--r-- 1 root root 4096 Sep 5 11:59 die_id
-r--r--r-- 1 root root 18446744073709551615 Sep 5 11:59 package_cpus
-r--r--r-- 1 root root 4096 Sep 5 11:59 package_cpus_list
-r--r--r-- 1 root root 4096 Sep 5 10:58 physical_package_id
-r--r--r-- 1 root root 18446744073709551615 Sep 5 10:10 thread_siblings
-r--r--r-- 1 root root 4096 Sep 5 11:59 thread_siblings_list
Adjust the inequality to catch the case when NR_CPUS is configured
to a small value.
Fixes: 7ee951acd31a ("drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: stable@vger.kernel.org
Cc: feng xiangjun <fengxj325@gmail.com>
Reported-by: feng xiangjun <fengxj325@gmail.com>
Signed-off-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Link: https://lore.kernel.org/r/20220906203542.1796629-1-pauld@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, SMC uses smc->sk.sk_{rcv|snd}buf to create buffers for
send buffer and RMB. And the values of buffer size are from tcp_{w|r}mem
in clcsock.
The buffer size from TCP socket doesn't fit SMC well. Generally, buffers
are usually larger than TCP for SMC-R/-D to get higher performance, for
they are different underlay devices and paths.
So this patch unbinds buffer size from TCP, and introduces two sysctl
knobs to tune them independently. Also, these knobs are per net
namespace and work for containers.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
SMC-R tests the viability of link by sending out TEST_LINK LLC
messages over RoCE fabric when connections on link have been
idle for a time longer than keepalive interval (testlink time).
But using tcp_keepalive_time as testlink time maybe not quite
suitable because it is default no less than two hours[1], which
is too long for single link to find peer dead. The active host
will still use peer-dead link (QP) sending messages, and can't
find out until get IB_WC_RETRY_EXC_ERR error CQEs, which takes
more time than TEST_LINK timeout (SMC_LLC_WAIT_TIME) normally.
So this patch introduces a independent sysctl for SMC-R to set
link keepalive time, in order to detect link down in time. The
default value is 30 seconds.
[1] https://www.rfc-editor.org/rfc/rfc1122#page-101
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In inter-subnet cases, when inbound/outbound PRs are available,
outbound_PR.dlid is used as the requestor's datapath DLID and
inbound_PR.dlid is used as the responder's DLID. The inbound_PR.dlid
is passed to responder side with the "ConnectReq.Primary_Local_Port_LID"
field. With this solution the PERMISSIVE_LID is no longer used in
Primary Local LID field.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/b3f6cac685bce9dde37c610be82e2c19d9e51d9e.1662631201.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Support receiving inbound and outbound IB path records (along with GMP
PathRecord) from user-space service through the RDMA netlink channel.
The LIDs in these 3 PRs can be used in this way:
1. GMP PR: used as the standard local/remote LIDs;
2. DLID of outbound PR: Used as the "dlid" field for outbound traffic;
3. DLID of inbound PR: Used as the "dlid" field for outbound traffic in
responder side.
This is aimed to support adaptive routing. With current IB routing
solution when a packet goes out it's assigned with a fixed DLID per
target, meaning a fixed router will be used.
The LIDs in inbound/outbound path records can be used to identify group
of routers that allow communication with another subnet's entity. With
them packets from an inter-subnet connection may travel through any
router in the set to reach the target.
As confirmed with Jason, when sending a netlink request, kernel uses
LS_RESOLVE_PATH_USE_ALL so that the service knows kernel supports
multiple PRs.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/2fa2b6c93c4c16c8915bac3cfc4f27be1d60519d.1662631201.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
This fields means the total number of primary and alternative paths,
i.e.,:
0 - No primary nor alternate path is available;
1 - Only primary path is available;
2 - Both primary and alternate path are available.
Rename it to avoid confusion as with follow patches primary path will
support multiple path records.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/cbe424de63a56207870d70c5edce7c68e45f429e.1662631201.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
request_queues are a block layer implementation detail that should not
leak into file systems. Change the fscrypt inline crypto code to
retrieve block devices instead of request_queues from the file system.
As part of that, clean up the interaction with multi-device file systems
by returning both the number of devices and the actual device array in a
single method call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ebiggers: bug fixes and minor tweaks]
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220901193208.138056-4-ebiggers@kernel.org
|
|
The approach of fs/crypto/ internally managing the fscrypt_master_key
structs as the payloads of "struct key" objects contained in a
"struct key" keyring has outlived its usefulness. The original idea was
to simplify the code by reusing code from the keyrings subsystem.
However, several issues have arisen that can't easily be resolved:
- When a master key struct is destroyed, blk_crypto_evict_key() must be
called on any per-mode keys embedded in it. (This started being the
case when inline encryption support was added.) Yet, the keyrings
subsystem can arbitrarily delay the destruction of keys, even past the
time the filesystem was unmounted. Therefore, currently there is no
easy way to call blk_crypto_evict_key() when a master key is
destroyed. Currently, this is worked around by holding an extra
reference to the filesystem's request_queue(s). But it was overlooked
that the request_queue reference is *not* guaranteed to pin the
corresponding blk_crypto_profile too; for device-mapper devices that
support inline crypto, it doesn't. This can cause a use-after-free.
- When the last inode that was using an incompletely-removed master key
is evicted, the master key removal is completed by removing the key
struct from the keyring. Currently this is done via key_invalidate().
Yet, key_invalidate() takes the key semaphore. This can deadlock when
called from the shrinker, since in fscrypt_ioctl_add_key(), memory is
allocated with GFP_KERNEL under the same semaphore.
- More generally, the fact that the keyrings subsystem can arbitrarily
delay the destruction of keys (via garbage collection delay, or via
random processes getting temporary key references) is undesirable, as
it means we can't strictly guarantee that all secrets are ever wiped.
- Doing the master key lookups via the keyrings subsystem results in the
key_permission LSM hook being called. fscrypt doesn't want this, as
all access control for encrypted files is designed to happen via the
files themselves, like any other files. The workaround which SELinux
users are using is to change their SELinux policy to grant key search
access to all domains. This works, but it is an odd extra step that
shouldn't really have to be done.
The fix for all these issues is to change the implementation to what I
should have done originally: don't use the keyrings subsystem to keep
track of the filesystem's fscrypt_master_key structs. Instead, just
store them in a regular kernel data structure, and rework the reference
counting, locking, and lifetime accordingly. Retain support for
RCU-mode key lookups by using a hash table. Replace fscrypt_sb_free()
with fscrypt_sb_delete(), which releases the keys synchronously and runs
a bit earlier during unmount, so that block devices are still available.
A side effect of this patch is that neither the master keys themselves
nor the filesystem keyrings will be listed in /proc/keys anymore.
("Master key users" and the master key users keyrings will still be
listed.) However, this was mostly an implementation detail, and it was
intended just for debugging purposes. I don't know of anyone using it.
This patch does *not* change how "master key users" (->mk_users) works;
that still uses the keyrings subsystem. That is still needed for key
quotas, and changing that isn't necessary to solve the issues listed
above. If we decide to change that too, it would be a separate patch.
I've marked this as fixing the original commit that added the fscrypt
keyring, but as noted above the most important issue that this patch
fixes wasn't introduced until the addition of inline encryption support.
Fixes: 22d94f493bfb ("fscrypt: add FS_IOC_ADD_ENCRYPTION_KEY ioctl")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220901193208.138056-2-ebiggers@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
netfilter patches for net-next
Remove GPL license copypastry in uapi files, those have SPDX tags.
From Christophe Jaillet.
Remove unused variable in rpfilter, from Guillaume Nault.
Rework gc resched delay computation in conntrack, from Antoine Tenart.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: rpfilter: Remove unused variable 'ret'.
headers: Remove some left-over license text in include/uapi/linux/netfilter/
netfilter: conntrack: revisit the gc initial rescheduling bias
netfilter: conntrack: fix the gc rescheduling delay
====================
Link: https://lore.kernel.org/r/20220921095000.29569-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Added by:
commit e5cf1baf92cb ("act_mirred: use TC_ACT_REINSERT when possible")
but no longer useful.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20220919130627.3551233-1-jhs@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We got report from sysbot [1] about warnings that were caused by
bpf program attached to contention_begin raw tracepoint triggering
the same tracepoint by using bpf_trace_printk helper that takes
trace_printk_lock lock.
Call Trace:
<TASK>
? trace_event_raw_event_bpf_trace_printk+0x5f/0x90
bpf_trace_printk+0x2b/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
bpf_trace_printk+0x3f/0xe0
bpf_prog_a9aec6167c091eef_prog+0x1f/0x24
bpf_trace_run2+0x26/0x90
native_queued_spin_lock_slowpath+0x1c6/0x2b0
_raw_spin_lock_irqsave+0x44/0x50
__unfreeze_partials+0x5b/0x160
...
The can be reproduced by attaching bpf program as raw tracepoint on
contention_begin tracepoint. The bpf prog calls bpf_trace_printk
helper. Then by running perf bench the spin lock code is forced to
take slow path and call contention_begin tracepoint.
Fixing this by skipping execution of the bpf program if it's
already running, Using bpf prog 'active' field, which is being
currently used by trampoline programs for the same reason.
Moving bpf_prog_inc_misses_counter to syscall.c because
trampoline.c is compiled in just for CONFIG_BPF_JIT option.
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Reported-by: syzbot+2251879aa068ad9c960d@syzkaller.appspotmail.com
[1] https://lore.kernel.org/bpf/YxhFe3EwqchC%2FfYf@krava/T/#t
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220916071914.7156-1-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
