| Age | Commit message (Collapse) | Author |
|---|
|
percpu_ref will be restructured so that percpu/atomic mode switching
and reference killing are dedoupled. In preparation, add
PCPU_REF_DEAD and PCPU_REF_ATOMIC_DEAD which is OR of ATOMIC and DEAD.
For now, ATOMIC and DEAD are changed together and all PCPU_REF_ATOMIC
uses are converted to PCPU_REF_ATOMIC_DEAD without causing any
behavior changes.
percpu_ref_init() now specifies an explicit alignment when allocating
the percpu counters so that the pointer has enough unused low bits to
accomodate the flags. Note that one flag was fine as min alignment
for percpu memory is 2 bytes but two flags are already too many for
the natural alignment of unsigned longs on archs like cris and m68k.
v2: The original patch had BUILD_BUG_ON() which triggers if unsigned
long's alignment isn't enough to accomodate the flags, which
triggered on cris and m64k. percpu_ref_init() updated to specify
the required alignment explicitly. Reported by Fengguang.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
|
|
percpu_ref will be restructured so that percpu/atomic mode switching
and reference killing are dedoupled. In preparation, do the following
renames.
* percpu_ref->confirm_kill -> percpu_ref->confirm_switch
* __PERCPU_REF_DEAD -> __PERCPU_REF_ATOMIC
* __percpu_ref_alive() -> __ref_is_percpu()
This patch is pure rename and doesn't introduce any functional
changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
|
|
percpu_ref uses pcpu_ prefix for internal stuff and percpu_ for
externally visible ones. This is the same convention used in the
percpu allocator implementation. It works fine there but percpu_ref
doesn't have too much internal-only stuff and scattered usages of
pcpu_ prefix are confusing than helpful.
This patch replaces all pcpu_ prefixes with percpu_. This is pure
rename and there's no functional change. Note that PCPU_REF_DEAD is
renamed to __PERCPU_REF_DEAD to signify that the flag is internal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
|
|
* Some comments became stale. Updated.
* percpu_ref_tryget() unnecessarily initializes @ret. Removed.
* A blank line removed from percpu_ref_kill_rcu().
* Explicit function name in a WARN format string replaced with __func__.
* WARN_ON() in percpu_ref_reinit() converted to WARN_ON_ONCE().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
|
|
percpu_ref is gonna go through restructuring. Move
percpu_ref_reinit() after percpu_ref_kill_and_confirm(). This will
make later changes easier to follow and result in cleaner
organization.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
|
|
probe"
This reverts commit 0a30288da1aec914e158c2d7a3482a85f632750f, which
was a temporary fix for SCSI blk-mq stall issue. The following
patches will fix the issue properly by introducing atomic mode to
percpu_ref.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-block into for-3.18
This is to receive 0a30288da1ae ("blk-mq, percpu_ref: implement a
kludge for SCSI blk-mq stall during probe") which implements
__percpu_ref_kill_expedited() to work around SCSI blk-mq stall. The
commit reverted and patches to implement proper fix will be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
|
|
Pull one last block fix from Jens Axboe:
"We've had an issue with scsi-mq where probing takes forever. This was
bisected down to the percpu changes for blk_mq_queue_enter(), and the
fact we now suffer an RCU grace period when killing a queue. SCSI
creates and destroys tons of queues, so this let to 10s of seconds of
stalls at boot for some.
Tejun has a real fix for this, but it's too involved for 3.17. So
this is a temporary workaround to expedite the queue killing until we
can fold in the real fix for 3.18 when that merge window opens"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe
|
|
Pull crypto fixes from Herbert Xu:
"This fixes three issues:
- if ccp is loaded on a machine without ccp, it will incorrectly
activate causing all requests to fail. Fixed by preventing ccp
from loading if hardware isn't available.
- not all IRQs were enabled for the qat driver, leading to potential
stalls when it is used
- disabled buggy AVX CTR implementation in aesni"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - disable "by8" AVX CTR optimization
crypto: ccp - Check for CCP before registering crypto algs
crypto: qat - Enable all 32 IRQs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For some last time fixes:
- a regression detected on Kernel 3.16 related to VBI Teletext
application breakage on drivers using videobuf2 (see
https://bugzilla.kernel.org/show_bug.cgi?id=84401). The bug was
noticed on saa7134 (migrated to VB2 on 3.16), but also affects
em28xx (migrated on 3.9 to VB2);
- two additional sanity checks at videobuf2;
- two fixups to restore proper VBI support at the em28xx driver;
- two Kernel oops fixups (at cx24123 and cx2341x drivers);
- a bug at adv7604 where an if was doing just the opposite as it
would be expected;
- some documentation fixups to match the behavior defined at the
Kernel"
* tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx-v4l: get rid of field "users" in struct em28xx_v4l2"
[media] em28xx: fix VBI handling logic
[media] DocBook media: improve the poll() documentation
[media] DocBook media: fix the poll() 'no QBUF' documentation
[media] vb2: fix VBI/poll regression
[media] cx2341x: fix kernel oops
[media] cx24123: fix kernel oops due to missing parent pointer
[media] adv7604: fix inverted condition
[media] media/radio: fix radio-miropcm20.c build with io.h header file
[media] vb2: fix plane index sanity check in vb2_plane_cookie()
[media] DocBook media: update version number and V4L2 changes
[media] DocBook media: fix fieldname in struct v4l2_subdev_selection
[media] vb2: fix vb2 state check when start_streaming fails
[media] videobuf2-core.h: fix comment
[media] videobuf2-core: add comments before the WARN_ON
[media] videobuf2-dma-sg: fix for wrong GFP mask to sg_alloc_table_from_pages
|
|
blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze. percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period. This means that draining a blk-mq
takes measureable wallclock time. One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.
Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs. This means that SCSI probing may take more than ten seconds
when scsi-mq is used.
This will be properly fixed by implementing a mechanism to keep
q->mq_usage_counter in atomic mode till genhd registration; however,
that involves rather big updates to percpu_ref which is difficult to
apply late in the devel cycle (v3.17-rc6 at the moment). As a
stop-gap measure till the proper fix can be implemented in the next
cycle, this patch introduces __percpu_ref_kill_expedited() and makes
blk_mq_freeze_queue() use it. This is heavy-handed but should work
for testing the experimental SCSI blk-mq implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fda981 ("blk-mq: use percpu_ref for mq usage count")
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch prepares for changing the max14577 charger driver to allow
configuring battery-dependent settings from DTS.
The patch moves from regulator driver to MFD core driver and exports:
- function for calculating register value for charger's current;
- table of limits for chargers (MAX14577, MAX77836).
Previously they were used only by the max14577 regulator driver. In next
patch the charger driver will use them as well. Exporting them will
reduce unnecessary code duplication.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The Keystone Navigator DMA driver sets up the dma channels and flows for
the QMSS(Queue Manager SubSystem) who triggers the actual data movements
across clients using destination queues. Every client modules like
NETCP(Network Coprocessor), SRIO(Serial Rapid IO) and CRYPTO
Engines has its own instance of packet dma hardware. QMSS has also
an internal packet DMA module which is used as an infrastructure
DMA with zero copy.
Initially this driver was proposed as DMA engine driver but since the
hardware is not typical DMA engine and hence doesn't comply with typical
DMA engine driver needs, that approach was naked. Link to that
discussion -
https://lkml.org/lkml/2014/3/18/340
As aligned, now we pair the Navigator DMA with its companion Navigator
QMSS subsystem driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of
the main hardware sub system which forms the backbone of the Keystone
Multi-core Navigator. QMSS consist of queue managers, packed-data structure
processors(PDSP), linking RAM, descriptor pools and infrastructure
Packet DMA.
The Queue Manager is a hardware module that is responsible for accelerating
management of the packet queues. Packets are queued/de-queued by writing or
reading descriptor address to a particular memory mapped location. The PDSPs
perform QMSS related functions like accumulation, QoS, or event management.
Linking RAM registers are used to link the descriptors which are stored in
descriptor RAM. Descriptor RAM is configurable as internal or external memory.
The QMSS driver manages the PDSP setups, linking RAM regions,
queue pool management (allocation, push, pop and notify) and descriptor
pool management. The specifics on the device tree bindings for
QMSS can be found in:
Documentation/devicetree/bindings/soc/keystone-navigator-qmss.txt
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
This patch restructures the memory controller (IMC) uncore PMU support
for client SNB/IVB/HSW processors. The main change is that it can now
cope with more than one PCI device ID per processor model. There are
many flavors of memory controllers for each processor. They have
different PCI device ID, yet they behave the same w.r.t. the memory
controller PMU that we are interested in.
The patch now supports two distinct memory controllers for IVB
processors: one for mobile, one for desktop.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140917090616.GA11281@quad
Cc: ak@linux.intel.com
Cc: kan.liang@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Prepare for adding support for MAX77836 charger to the max14577 charger
driver by adding necessary new defines and prefixes to existing ones.
The MAX77836 uses slightly different values for ChgTyp field of STATUS2
register. On the MAX14577 value of 0x6 is reserved and 0x7 dead battery.
On the MAX77836 the opposite:
- 0x6 means special charger,
- 0x7 is reserved.
Regardless of these differences use one common enum
max14577_muic_charger_type.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Currently, the APIC access page is pinned by KVM for the entire life
of the guest. We want to make it migratable in order to make memory
hot-unplug available for machines that run KVM.
This patch prepares to handle this in generic code, through a new
request bit (that will be set by the MMU notifier) and a new hook
that is called whenever the request bit is processed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
it non-static
Different architectures need different requests, and in fact we
will use this function in architecture-specific code later. This
will be outside kvm_main.c, so make it non-static and rename it to
kvm_make_all_cpus_request().
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
1. We were calling clear_flush_young_notify in unmap_one, but we are
within an mmu notifier invalidate range scope. The spte exists no more
(due to range_start) and the accessed bit info has already been
propagated (due to kvm_pfn_set_accessed). Simply call
clear_flush_young.
2. We clear_flush_young on a primary MMU PMD, but this may be mapped
as a collection of PTEs by the secondary MMU (e.g. during log-dirty).
This required expanding the interface of the clear_flush_young mmu
notifier, so a lot of code has been trivially touched.
3. In the absence of shadow_accessed_mask (e.g. EPT A bit), we emulate
the access bit by blowing the spte. This requires proper synchronizing
with MMU notifier consumers, like every other removal of spte's does.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Callbacks don't have to do extra computation to learn what the caller
(lvm_handle_hva_range()) knows very well. Useful for
debugging/tracing/printk/future.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When KVM handles a tdp fault it uses FOLL_NOWAIT. If the guest memory
has been swapped out or is behind a filemap, this will trigger async
readahead and return immediately. The rationale is that KVM will kick
back the guest with an "async page fault" and allow for some other
guest process to take over.
If async PFs are enabled the fault is retried asap from an async
workqueue. If not, it's retried immediately in the same code path. In
either case the retry will not relinquish the mmap semaphore and will
block on the IO. This is a bad thing, as other mmap semaphore users
now stall as a function of swap or filemap latency.
This patch ensures both the regular and async PF path re-enter the
fault allowing for the mmap semaphore to be relinquished in the case
of IO wait.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The core specification defines valid values for the
HCI_Reject_Synchronous_Connection_Request command to be 0x0D-0x0F. So
far the code has been using HCI_ERROR_REMOTE_USER_TERM (0x13) which is
not a valid value and is therefore being rejected by some controllers:
> HCI Event: Connect Request (0x04) plen 10
bdaddr 40:6F:2A:6A:E5:E0 class 0x000000 type eSCO
< HCI Command: Reject Synchronous Connection (0x01|0x002a) plen 7
bdaddr 40:6F:2A:6A:E5:E0 reason 0x13
Reason: Remote User Terminated Connection
> HCI Event: Command Status (0x0f) plen 4
Reject Synchronous Connection (0x01|0x002a) status 0x12 ncmd 1
Error: Invalid HCI Command Parameters
This patch introduces a new define for a value from the valid range
(0x0d == Connection Rejected Due To Limited Resources) and uses it
instead for rejecting incoming connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add support for a extended PL022 which has an extra register for controlling up
to five chip select signals. This controller is found on the AXM5516 SoC.
Unfortunately the PrimeCell identification registers are identical to a
standard ARM PL022. To work around this, the peripheral ID must be overridden
in the device tree using the "arm,primecell-periphid" property with the value
0x000b6022.
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
No caller or macro uses the return value so make all
the functions return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
- Add devm_kasprintf()/kvasprintf(), introduced by commit
75f2a4ead5d5890ada9c2663a70fb58613c0d9f2 ("devres: Add
devm_kasprintf and devm_kvasprintf API"), to
Documentation/driver-model/devres.txt,
- Improve kernel doc: the string is not an existing formatted string,
but is formatted into the newly-allocated buffer,
- Add a __printf() annotation to devm_kasprintf(), so the compiler
will verify the format string argument types.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Properly pack the data for file copy functionality. Patch based on
investigation done by Matej Muzila <mmuzila@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: <qge@redhat.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the ccp is built as a built-in module, then ccp-crypto (whether
built as a module or a built-in module) will be able to load and
it will register its crypto algorithms. If the system does not have
a CCP this will result in -ENODEV being returned whenever a command
is attempted to be queued by the registered crypto algorithms.
Add an API, ccp_present(), that checks for the presence of a CCP
on the system. The ccp-crypto module can use this to determine if it
should register it's crypto alogorithms.
Cc: stable@vger.kernel.org
Reported-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Updated email address of co-author.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Calling strncpy with a maximum size argument of 32 bytes on destination
array kim_gdata->dev_name of size 32 bytes might leave the destination
string unterminated.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There was not any kind of protection against carrier driver removal.
In this way, device driver can 'get' the carrier driver when it is
using it.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many devices run firmware and/or complex hardware, and most of that
can have bugs. When it misbehaves, however, it is often much harder
to debug than software running on the host.
Introduce a "device coredump" mechanism to allow dumping internal
device/firmware state through a generalized mechanism. As devices
are different and information needed can vary accordingly, this
doesn't prescribe a file format - it just provides mechanism to
get data to be able to capture it in a generalized way (e.g. in
distributions.)
The dumped data will be readable in sysfs in the virtual device's
data file under /sys/class/devcoredump/devcd*/. Writing to it will
free the data and remove the device, as does a 5-minute timeout.
Note that generalized capturing of such data may result in privacy
issues, so users generally need to be involved. In order to allow
certain users/system integrators/... to disable the feature at all,
introduce a Kconfig option to override the drivers that would like
to have the feature.
For now, this provides two ways of dumping data:
1) with a vmalloc'ed area, that is then given to the subsystem
and freed after retrieval or timeout
2) with a generalized reader/free function method
We could/should add more options, e.g. a list of pages, since the
vmalloc area is very limited on some architectures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the BIT macro instead of "open coding" bit fields. This makes it
easier to actually see that the bits are not conflicting/overlapping.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v3.18 merge window" from Tony Lindgren:
Changes for .dts files for omaps for v3.18 merge window:
- Updates for gta04 to add gta04a3 model
- Add support for Tehnexion TAO3530 boards
- Regulator names for beaglebone
- Pinctrl related updates for omap5, dra7 and am437
- Model name fix for sbc-t54
- Enable mailbox for various omaps
* tag 'dt-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (291 commits)
ARM: dts: OMAP2+: Add sub mailboxes device node information
ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable
ARM: dts: OMAP5 / DRA7: switch over to interrupts-extended property for UART
ARM: dts: AM437x: switch to compatible pinctrl
ARM: dts: DRA7: switch to compatible pinctrl
ARM: dts: OMAP5: switch to compatible pinctrl
ARM: dts: am335x-boneblack: Add names for remaining regulators
ARM: dts: sbc-t54: fix model property
ARM: dts: omap5.dtsi: add DSS RFBI node
ARM: dts: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based)
ARM: dts: omap3: Add Technexion Thunder support (TAO3530 SOM based)
ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
ARM: OMAP2+: tao3530: Add pdata-quirk for the mmc2 internal clock
ARM: OMAP2+: board-generic: add support for AM57xx family
ARM: dts: dra72-evm: Add tps65917 PMIC node
ARM: dts: dra72-evm: Enable I2C1 node
Linux 3.17-rc3
unicore32: Fix build error
vexpress/spc: fix a build warning on array bounds
spi: sh-msiof: Fix transmit-only DMA transfers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC related changes for omaps for v3.18 merge window:
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
ARM: dts: OMAP3+: Add PRM interrupt
ARM: omap: Remove stray ARCH_HAS_OPP references
ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
ARM: AM437x: use pdata quirks for pinctrl information
ARM: DRA7: use pdata quirks for pinctrl information
ARM: OMAP5: use pdata quirks for pinctrl information
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
...
|
|
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List)
for USB OTG & EH certification and other vendor specific requirements.
The platform who needs TPL feature should set this flag at usb host
controller driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Alpha EV4/EV5 cpus can corrupt adjacent byte and short data because
those cpus use RMW to store byte and short data. Thus, concurrent adjacent
byte stores could become corrupted, if serialized by a different lock.
tty_struct uses different locks to protect certain fields within the
structure, and thus is vulnerable to byte stores which are not atomic.
Merge the ->ctrl_status byte and packet mode bit, both protected by the
->ctrl_lock, into an unsigned long.
The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes required to store the bitfield.
In turn, this would allow Alpha EV4/EV5 cpus to corrupt adjacent byte
or short storage (because those cpus use RMW to store byte and short data).
gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64, and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to fix the Alpha non-atomic storage problem).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Relocate the file-scope function, send_prio_char(), as a global
helper tty_send_xchar(). Remove the global declarations for
tty_write_lock()/tty_write_unlock(), as these are file-scope only now.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use newly-introduced tty->flow_lock to serialize updates to
tty->flow_stopped (via tcflow()) and with concurrent tty flow
control changes from other sources.
Merge the storage for ->stopped and ->flow_stopped, now that both
flags are serialized by ->flow_lock.
The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes necessary to store the bitfield.
In turn, this would allow Alpha EV4 and EV5 cpus to corrupt adjacent
byte storage because those cpus use RMW to store byte and short data.
gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64 and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to workaround the Alpha non-atomic byte/short storage problem).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without serialization, the flow control state can become inverted
wrt. the actual hardware state. For example,
CPU 0 | CPU 1
stop_tty() |
lock ctrl_lock |
tty->stopped = 1 |
unlock ctrl_lock |
| start_tty()
| lock ctrl_lock
| tty->stopped = 0
| unlock ctrl_lock
| driver->start()
driver->stop() |
In this case, the flow control state now indicates the tty has
been started, but the actual hardware state has actually been stopped.
Introduce tty->flow_lock spinlock to serialize tty flow control changes.
Split out unlocked __start_tty()/__stop_tty() flavors for use by
ioctl(TCXONC) in follow-on patch.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The stopped, hw_stopped, flow_stopped and packet bits are smp-unsafe
and interrupt-unsafe. For example,
CPU 0 | CPU 1
|
tty->flow_stopped = 1 | tty->hw_stopped = 0
One of these updates will be corrupted, as the bitwise operation
on the bitfield is non-atomic.
Ensure each flag has a separate memory location, so concurrent
updates do not corrupt orthogonal states. Because DEC Alpha EV4 and EV5
cpus (from 1995) perform RMW on smaller-than-machine-word storage,
"separate memory location" must be int instead of byte.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.
Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
