| Age | Commit message (Collapse) | Author |
|---|
|
Commit b58cc46c5f6b (rcu: Don't offload callbacks unless specifically
requested) failed to adjust the callback lists of the CPUs that are
known to be no-CBs CPUs only because they are also nohz_full= CPUs.
This failure can result in callbacks that are posted during early boot
getting stranded on nxtlist for CPUs whose no-CBs property becomes
apparent late, and there can also be spurious warnings about offline
CPUs posting callbacks.
This commit fixes these problems by adding an early-boot rcu_init_nohz()
that properly initializes the no-CBs CPUs.
Note that kernels built with CONFIG_RCU_NOCB_CPU_ALL=y or with
CONFIG_RCU_NOCB_CPU=n do not exhibit this bug. Neither do kernels
booted without the nohz_full= boot parameter.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Make use of the new match string preparsing to overhaul key identification
when searching for asymmetric keys. The following changes are made:
(1) Use the previously created asymmetric_key_id struct to hold the following
key IDs derived from the X.509 certificate or PKCS#7 message:
id: serial number + issuer
skid: subjKeyId + subject
authority: authKeyId + issuer
(2) Replace the hex fingerprint attached to key->type_data[1] with an
asymmetric_key_ids struct containing the id and the skid (if present).
(3) Make the asymmetric_type match data preparse select one of two searches:
(a) An iterative search for the key ID given if prefixed with "id:". The
prefix is expected to be followed by a hex string giving the ID to
search for. The criterion key ID is checked against all key IDs
recorded on the key.
(b) A direct search if the key ID is not prefixed with "id:". This will
look for an exact match on the key description.
(4) Make x509_request_asymmetric_key() take a key ID. This is then converted
into "id:<hex>" and passed into keyring_search() where match preparsing
will turn it back into a binary ID.
(5) X.509 certificate verification then takes the authority key ID and looks
up a key that matches it to find the public key for the certificate
signature.
(6) PKCS#7 certificate verification then takes the id key ID and looks up a
key that matches it to find the public key for the signed information
block signature.
Additional changes:
(1) Multiple subjKeyId and authKeyId values on an X.509 certificate cause the
cert to be rejected with -EBADMSG.
(2) The 'fingerprint' ID is gone. This was primarily intended to convey PGP
public key fingerprints. If PGP is supported in future, this should
generate a key ID that carries the fingerprint.
(3) Th ca_keyid= kernel command line option is now converted to a key ID and
used to match the authority key ID. Possibly this should only match the
actual authKeyId part and not the issuer as well.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
Implement the first step in using binary key IDs for asymmetric keys rather
than hex string keys.
The previously added match data preparsing will be able to convert hex
criterion strings into binary which can then be compared more rapidly.
Further, we actually want more then one ID string per public key. The problem
is that X.509 certs refer to other X.509 certs by matching Issuer + AuthKeyId
to Subject + SubjKeyId, but PKCS#7 messages match against X.509 Issuer +
SerialNumber.
This patch just provides facilities for a later patch to make use of.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
Make the key matching functions pointed to by key_match_data::cmp return bool
rather than int.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
A previous patch added a ->match_preparse() method to the key type. This is
allowed to override the function called by the iteration algorithm.
Therefore, we can just set a default that simply checks for an exact match of
the key description with the original criterion data and allow match_preparse
to override it as needed.
The key_type::match op is then redundant and can be removed, as can the
user_match() function.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
Remove key_type::def_lookup_type as it's no longer used. The information now
defaults to KEYRING_SEARCH_LOOKUP_DIRECT but may be overridden by
type->match_preparse().
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
Preparse the match data. This provides several advantages:
(1) The preparser can reject invalid criteria up front.
(2) The preparser can convert the criteria to binary data if necessary (the
asymmetric key type really wants to do binary comparison of the key IDs).
(3) The preparser can set the type of search to be performed. This means
that it's not then a one-off setting in the key type.
(4) The preparser can set an appropriate comparator function.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
Provide a function to convert a buffer of binary data into an unterminated
ascii hex string representation of that data.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
|
|
This patch introduces virtual endpoint address mapping. It separates
function logic form physical endpoint addresses making it more hardware
independent.
Following modifications changes user space API, so to enable them user
have to switch on the FUNCTIONFS_VIRTUAL_ADDR flag in descriptors.
Endpoints are now refered using virtual endpoint addresses chosen by
user in endpoint descpriptors. This applies to each context when endpoint
address can be used:
- when accessing endpoint files in FunctionFS filesystemi (in file name),
- in setup requests directed to specific endpoint (in wIndex field),
- in descriptors returned by FUNCTIONFS_ENDPOINT_DESC ioctl.
In endpoint file names the endpoint address number is formatted as
double-digit hexadecimal value ("ep%02x") which has few advantages -
it is easy to parse, allows to easly recognize endpoint direction basing
on its name (IN endpoint number starts with digit 8, and OUT with 0)
which can be useful for debugging purpose, and it makes easier to introduce
further features allowing to use each endpoint number in both directions
to have more endpoints available for function if hardware supports this
(for example we could have ep01 which is endpoint 1 with OUT direction,
and ep81 which is endpoint 1 with IN direction).
Physical endpoint address can be still obtained using ioctl named
FUNCTIONFS_ENDPOINT_REVMAP, but now it's not neccesary to handle
USB transactions properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Linux 3.17-rc5
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
Documentation/devicetree/bindings/usb/mxs-phy.txt
drivers/usb/phy/phy-mxs-usb.c
|
|
Currently, we call ioapic_service() immediately when we find the irq is still
active during eoi broadcast. But for real hardware, there's some delay between
the EOI writing and irq delivery. If we do not emulate this behavior, and
re-inject the interrupt immediately after the guest sends an EOI and re-enables
interrupts, a guest might spend all its time in the ISR if it has a broken
handler for a level-triggered interrupt.
Such livelock actually happens with Windows guests when resuming from
hibernation.
As there's no way to recognize the broken handle from new raised ones, this patch
delays an interrupt if 10.000 consecutive EOIs found that the interrupt was
still high. The guest can then make a little forward progress, until a proper
IRQ handler is set or until some detection routine in the guest (such as
Linux's note_interrupt()) recognizes the situation.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Zhang Haoyu <zhanghy@sangfor.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
power_supply.h requires to forward declare few structures. One of them is done
at the top of the file and other one just before it is used. Declare them
together for better readability.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Currently we genarate a queueing route if we have matching policies
but can not resolve the states and the sysctl xfrm_larval_drop is
disabled. Here we assume that dst_output() is called to kill the
queued packets. Unfortunately this assumption is not true in all
cases, so it is possible that these packets leave the system unwanted.
We fix this by generating queueing routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: a0073fe18e71 ("xfrm: Add a state resolution packet queue")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: 2774c131b1d ("xfrm: Handle blackhole route creation via afinfo.")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Recirc action allows a packet to reenter openvswitch processing.
currently openvswitch lookup flow for packet received and execute
set of actions on that packet, with help of recirc action we can
process/modify the packet and recirculate it back in openvswitch
for another pass.
OVS hash action calculates 5-tupple hash and set hash in flow-key
hash. This can be used along with recirculation for distributing
packets among different ports for bond devices.
For example:
OVS bonding can use following actions:
Match on: bond flow; Action: hash, recirc(id)
Match on: recirc-id == id and hash lower bits == a;
Action: output port_bond_a
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
|
|
Add gpt_3m clock for i.mx6qdl, as gpt can source clock
from OSC, some i.MX6 series SOCs has fixed divider of
8 for gpt clock, so here add a fix clk of gpt_3m.
i.MX6Q TO1.0 has no gpt_3m option, so force it to be
from ipg_per.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Each SSI has "ssi", "ssi_ipg" clocks, and they share same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This is the same change for imx6sx clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sx.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This is the same change for imx6sl clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The imx6q clock driver currently hard-codes all PLL clocks to source
from OSC24M without BYPASS support. The patch adds the missing lvds_in
clock which is mutually exclusive with lvds_gate, and implements BYPASS
and BYPASS_CLK_SRC selection for PLL clocks as per Figure 10-3. Primary
Clock Generation in IMX6DQRM, i.e. both BYPASS_CLK_SRC and BYPASS bits
are implemented as mux clocks, and ENABLE bit of PLL clocks is
implemented as a gate clock after BYPASS mux.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
ASRC has "asrc", "asrc_ipg", "asrc_mem" clocks, and they share
the same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
There are three clock for ESAI, esai_extal, esai_ipg, esai_mem. Rename
'esai' to 'esai_extal', 'esai_ahb' to 'esai_mem', and add 'esai_ipg'.
Make the clock for ESAI more clear and align them with imx6sx.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This commit adds PLL7 which is required for USBPHY1. It also adds
the USB PHY and USB Controller clocks and the gates to enable them.
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
|
|
As the Soekris net6501 and other e6xx based systems do not have
any ACPI implementation, HPET won't get enabled.
This patch enables HPET on such platforms.
[ 0.430149] pci 0000:00:01.0: Force enabled HPET at 0xfed00000
[ 0.644838] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Original patch by Peter Neubauer (http://www.mail-archive.com/soekris-tech@lists.soekris.com/msg06462.html)
slightly modified by Conrad Kostecki <ck@conrad-kostecki.de> and massaged
accoring to Thomas Gleixners <tglx@linutronix.de> by me.
Suggested-by: Conrad Kostecki <ck@conrad-kostecki.de>
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@lsexperts.de>
Cc: Peter Neubauer <pneubauer@bluerwhite.org>
Link: http://lkml.kernel.org/r/5412D3A5.2030909@lsexperts.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The synchronization protocol is not compatible with heterogeneous pools, so
we need to verify that we're not turning both on at the same time.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The assumption that dest af is equal to service af is now unreliable, so we
must specify it manually so as not to copy just the first 4 bytes of a v6
address or doing an illegal read of 16 butes on a v6 address.
We "lie" in two places: for synchronization (which we will explicitly
disallow from happening when we have heterogeneous pools) and for black
hole addresses where there's no real dest.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
We need to remove the assumption that virtual address family is the same as
real address family in order to support heterogeneous services (that is,
services with v4 vips and v6 backends or the opposite).
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
This is necessary to support heterogeneous pools. For example, if you have
an ipv6 addressed network, you'll want to be able to forward ipv4 traffic
into it.
This patch enforces that destination address family is the same as service
family, as none of the forwarding mechanisms support anything else.
For the old setsockopt mechanism, we simply set the dest address family to
AF_INET as we do with the service.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
|
|
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a use_cmd_list flag in struct Scsi_Host to request keeping track of
all outstanding commands per device.
Default behaviour is not to keep track of cmd_list per sdev, as this may
introduce lock contention. (overhead is more on multi-node NUMA.), and
only enable it on the two drivers that need it.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Please try the fix below, looks like the commit broke TCQ for all drivers
using block-level tagging.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Do not send zero valued skbinfo extensions to userspace at listing.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
Skbinfo extension provides mapping of metainformation with lookup in the ipset tables.
This patch defines the flags, the constants, the functions and the structures
for the data type independent support of the extension.
Note the firewall mark stores in the kernel structures as two 32bit values,
but transfered through netlink as one 64bit value.
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
|
|
Revert parts of f244d8b623da ("ACPIPHP / radeon / nouveau: Fix VGA
switcheroo problem related to hotplug").
A previous commit 5493b31f0b55 ("PCI: Add pci_ignore_hotplug() to ignore
hotplug events for a device") added equivalent functionality implemented in
a different way for both acpiphp and pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Rajat Jain <rajatxjain@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull crypto fixes from Herbert Xu:
"This fixes the newly added drbg generator so that it actually works on
32-bit machines. Previously the code was only tested on 64-bit and on
32-bit it overflowed and simply doesn't work"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: drbg - remove check for uninitialized DRBG handle
crypto: drbg - backport "fix maximum value checks on 32 bit systems"
|
|
Rewrite VXpocket and VX222 drivers to use the new PCM nonatomic ops.
The former irq tasklet is replaced with a threaded irq handler, and
the tasklet for the PCM delayed start is simply merged into the normal
PCM trigger, as well as the replacement of spinlock with mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Here's the updated topic/core-stuff pull request with the two patches
already merged into drm-fixes dropped.
* tag 'topic/core-stuff-2014-09-15' of git://anongit.freedesktop.org/drm-intel:
drm: Drop modeset locking from crtc init function
drm/i915/hdmi: Enable pipe pixel replication for SD interlaced modes
drm/edid: Reduce horizontal timings for pixel replicated modes
drm: Include task->name and master status in debugfs clients info
drm/gem: Fix kerneldoc typo
drm: use c99 initializers in structures
drm: fix drm_modeset_lock.h kernel-doc notation
|
|
In preparation for DT support where panel timings will be described by a
DRM-agnostic video mode, replace the struct drm_mode_modeinfo instance
in the panel platform data with a struct videomode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Bluetooth core already does processing of the HCI command header
and puts it together before sending it to the driver. It is not really
efficient for the driver to look at the HCI command header again in
case it has to make certain decisions about certain commands. To make
this easier, just provide the opcode as part of the SKB control buffer
information. The extra information about the opcode is optional and
only provided for HCI commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This fixes a merge conflict in lustre, and we want the other fixes that
went into 3.17-rc5 as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The performance regression that Josef Bacik reported in the pathname
lookup (see commit 99d263d4c5b2 "vfs: fix bad hashing of dentries") made
me look at performance stability of the dcache code, just to verify that
the problem was actually fixed. That turned up a few other problems in
this area.
There are a few cases where we exit RCU lookup mode and go to the slow
serializing case when we shouldn't, Al has fixed those and they'll come
in with the next VFS pull.
But my performance verification also shows that link_path_walk() turns
out to have a very unfortunate 32-bit store of the length and hash of
the name we look up, followed by a 64-bit read of the combined hash_len
field. That screws up the processor store to load forwarding, causing
an unnecessary hickup in this critical routine.
It's caused by the ugly calling convention for the "hash_name()"
function, and easily fixed by just making hash_name() fill in the whole
'struct qstr' rather than passing it a pointer to just the hash value.
With that, the profile for this function looks much smoother.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
