| Age | Commit message (Collapse) | Author |
|---|
|
Currently there is no callback for cpufreq drivers which is called once the
policy is ready to be used. There are some requirements where such a callback is
required.
One of them is registering a cooling device with the help of
of_cpufreq_cooling_register(). This routine tries to get 'struct cpufreq_policy'
for CPUs which isn't yet initialed at the time ->init() is called and so we face
issues while registering the cooling device.
Because we can't register cooling device from ->init(), we need a callback that
is called after the policy is ready to be used and hence we introduce ->ready()
callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Adding any new callback to 'struct cpufreq_driver' gives following checkpatch
warning:
WARNING: Unnecessary space before function pointer arguments
+ void (*ready) (struct cpufreq_policy *policy);
This is because we have been using a tab spacing between function pointer name
and its arguments and the new one tried to follow that.
Though we normally don't try to fix every checkpatch warning, specially around
formatting issues as that creates unnecessary noise over lists. But I thought we
better fix this so that new additions don't generate these warnings plus it
looks far better/symmetric now.
So, remove these tab spacing issues in 'struct cpufreq_driver' only + fix
alignment of all members.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into clk-next
Immutable branch between MFD, Regulator and Clk, due for v3.19
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
- clock phase setting capability for the rk3288 mmc clocks
- pll init to allow syncing to actual rate table values
- some more exported clocks
- fixes for some clocks (typos etc) all of them not yet used
in actual drivers
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/omap-gpmc
Pull "move omap gpmc to drivers finally" from Tony Lindgren:
We can finally move the GPMC code to live in drivers/memory for
further clean up work.
Note that we still have dependencies to the legacy booting for
omap3 board-*.c files for setting up the board specific memory
timings. For that we need the timing related things still exposed
in include/linux/omap-gpmc.h. This will all become private data
to the GPMC driver once the legacy booting support can be dropped.
* tag 'omap-for-v3.19/gpmc-move-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
|
|
The commit [7a2e9ddc: ALSA: usb-audio: Add native DSD support for
Denon/Marantz DACs] requires the new format definition that has
landed only in for-next branch.
|
|
Commit
853a33ce6932 irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
Introduced a series of warnings when building ARM multi_v7_defconfig:
include/linux/irqchip/arm-gic.h:109:53: warning: its scope is only this definition or declaration, which is probably not what you want
In file included from arch/arm/mach-ux500/pm.c:13:0:
include/linux/irqchip/arm-gic.h:109:53: warning: 'struct irq_domain' declared inside parameter list
int gicv2m_of_init(struct device_node *node, struct irq_domain *parent);
^
Fix this by adding the proper include.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
[ jac merged much more correct version from Marc into this patch ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/1417170975-1163-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Now, with the CLCD DT support available, there is no
more reason to keep the non-DT support for V2P-CA9.
Removed, together with "some" supporting code. It was
necessary to make PLAT_VERSATILE_SCHED_CLOCK optional
and selected by the machines still interested in it.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
|
|
This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Pull "The i.MX SoC update for 3.19" from Shawn Guo
- Update i.MX6 suspend code to check DDR instead of CPU type, as the
difference we need to handle is between LPDDR2 and DDR3, not SoCs.
- Set anatop properly for LPDDR2 in DSM mode
- Add support for new SoC LS1021A which integrates dual Cortex-A7
- Add ENET initialization for i.MX6SX platform
- Add cpufreq support for i.MX53 platform
- Add a SNVS based poweroff driver for i.MX6 platforms
- Use ARM Global Timer as clocksource on VF610
Note: the change set is built on top of tag imx-fixes-3.18-2 to resolve
a conflict on file arch/arm/mach-imx/clk-vf610.c.
* tag 'imx-soc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
ARM: imx: clk-vf610: get input clocks from assigned clocks
ARM: imx: Add Freescale LS1021A SMP support
ARM: imx: Add initial support for Freescale LS1021A
ARM: imx53: add cpufreq support
ARM: imx53: clk: add ARM clock
ARM: imx: add CPU clock type
ARM: imx5: add step clock, used when reprogramming PLL1
ARM: imx: add enet init for i.mx6sx
ARM: imx6sx: add imx6sx iomux-gpr field define
ARM: vf610: Add ARM Global Timer clocksource option
ARM: imx: add anatop settings for LPDDR2 when enter DSM mode
ARM: imx: replace cpu type check with ddr type check
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
|
|
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the regulatory settings change, some channels might become invalid.
Disconnect interfaces acting on these channels, after giving userspace
code a grace period to leave them.
This mode is currently opt-in, and not all interface operating modes are
supported for regulatory-enforcement checks. A wiphy that wishes to use
the new enforcement code must specify an appropriate regulatory flag,
and all its supported interface modes must be supported by the checking
code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
[fix some indentation, typos]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The Target responds to the ATR_REQ with the ATR_RES. Configure the General
Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP
magic number, followed by some LLC Parameters TLVs described in section
4.5 of [LLCP].
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Changes:
* Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF.
* Store the General Bytes of ATR_REQ.
* Signal that Target mode is activated in case of an activation in NFC-DEP.
* Update the NCI state accordingly.
* Use the various constants defined in nfc.h.
* Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the
Activation Parameters for both Poll and Listen mode contain all the bytes of
ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL].
In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are
numbered starting from Byte 1.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled.
Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When an NFC-DEP Initiator times out when waiting for
a DEP_RES from the Target, its supposed to send an
ATN to the Target. The Target should respond to the
ATN with a similar ATN PDU and the Initiator can then
resend the last non-ATN PDU that it sent. No more
than 'N(retry,atn)' are to be send where
2 <= 'N(retry,atn)' <= 5. If the Initiator had just
sent a NACK PDU when the timeout occurred, it is to
continue sending NACKs until 'N(retry,nack)' NACKs
have been send. This is described in section
14.12.5.6 of the NFC-DEP Digital Protocol Spec.
The digital layer's NFC-DEP code doesn't implement
this so add that support.
The value chosen for 'N(retry,atn)' is 2.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When an NFC-DEP Target receives a NACK PDU with
a PNI equal to 1 less than the current PNI, it
is supposed to re-send the last PDU. This is
implied in section 14.12.5.4 of the NFC Digital
Protocol Spec.
The digital layer's NFC-DEP code doesn't implement
Target-side NACK handing so add it. The last PDU
that was sent is saved in the 'nfc_digital_dev'
structure's 'saved_skb' member. The skb will have
an additional reference taken to ensure that the skb
isn't freed when the driver performs a kfree_skb()
on the skb. The length of the skb/PDU is also saved
so the length can be restored when re-sending the PDU
in the skb (the driver will perform an skb_pull() so
an skb_push() needs to be done to restore the skb's
data pointer/length).
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When an NFC-DEP Initiator receives a frame with
an incorrect CRC or with a parity error, and the
frame is at least 4 bytes long, its supposed to
send a NACK to the Target. The Initiator can
send up to 'N(retry,nack)' consecutive NACKs
where 2 <= 'N(retry,nack)' <= 5. When the limit
is exceeded, a PROTOCOL EXCEPTION is raised.
Any other type of transmission error is to be
ignored and the Initiator should continue
waiting for a new frame. This is described
in section 14.12.5.4 of the NFC Digital Protocol
Spec.
The digital layer's NFC-DEP code doesn't implement
any of this so add it. This support diverges from
the spec in two significant ways:
a) NACKs will be sent for ANY error reported by the
driver except a timeout. This is done because
there is currently no way for the digital layer
to distinguish a CRC or parity error from any
other type of error reported by the driver.
b) All other errors will cause a PROTOCOL EXCEPTION
even frames with CRC errors that are less than 4
bytes.
The value chosen for 'N(retry,nack)' is 2.
Targets do not send NACK PDUs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the NFC-DEP code is given a packet to send
that is larger than the peer's maximum payload,
its supposed to set the 'MI' bit in the 'I' PDU's
Protocol Frame Byte (PFB). Setting this bit
indicates that NFC-DEP chaining is to occur.
When NFC-DEP chaining is progress, sender 'I' PDUs
are acknowledged with 'ACK' PDUs until the last 'I'
PDU in the chain (which has the 'MI' bit cleared)
is responded to with a normal 'I' PDU. This can
occur while in Initiator mode or in Target mode.
Sender NFC-DEP chaining is currently not implemented
in the digital layer so add that support. Unfortunately,
since sending a frame may require writing the CRC to the
end of the data, the relevant data part of the original
skb must be copied for each intermediate frame.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The maximum payload for NFC-DEP exchanges (i.e., the
number of bytes between SoD and EoD) is negotiated
using the ATR_REQ, ATR_RES, and PSL_REQ commands.
The valid maximum lengths are 64, 128, 192, and 254
bytes.
Currently, NFC-DEP code assumes that both sides are
always using 254 byte maximums and ignores attempts
by the peer to change it. Instead, implement the
negotiation code, enforce the local maximum when
receiving data from the peer, and don't send payloads
that exceed the remote's maximum. The default local
maximum is 254 bytes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When in Target mode, the Initiator specifies whether
subsequent DEP_REQ and DEP_RES frames will include
a DID byte by the value passed in the ATR_REQ. If
the DID value in the ATR_REQ is '0' then no DID
byte will be included. If the DID value is between
'1' and '14' then a DID byte containing the same
value must be included in subsequent DEP_REQ and
DEP_RES frames. Any other DID value is invalid.
This is specified in sections 14.8.1.2 and 14.8.2.2
of the NFC Digital Protocol Spec.
Checking the DID value (if it should be there at all),
is not currently supported by the digital layer's
NFC-DEP code. Add this support by remembering the
DID value in the ATR_REQ, checking the DID value of
received DEP_REQ frames (if it should be there at all),
and including the remembered DID value in DEP_RES
frames when appropriate.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Those values (__NR_seccomp_*) are used solely in secure_computing()
to identify mode 1 system calls. If compat system calls have different
syscall numbers, asm/seccomp.h may override them.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This regeset is intended to be used to get and set a system call number
while tracing.
There was some discussion about possible approaches to do so:
(1) modify x8 register with ptrace(PTRACE_SETREGSET) indirectly,
and update regs->syscallno later on in syscall_trace_enter(), or
(2) define a dedicated regset for this purpose as on s390, or
(3) support ptrace(PTRACE_SET_SYSCALL) as on arch/arm
Thinking of the fact that user_pt_regs doesn't expose 'syscallno' to
tracer as well as that secure_computing() expects a changed syscall number,
especially case of -1, to be visible before this function returns in
syscall_trace_enter(), (1) doesn't work well.
We will take (2) since it looks much cleaner.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
|
|
These clocks represent the physical clocks (including phases) and they will
later be used for clock phase tuning.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This exposes the clock that comes out of the i2s block which generally
goes to the audio codec.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
[removed CLK_SET_RATE_PARENT from original patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Version 20141107.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This macro is intended to simplify the constuction of _PLD buffers.
NOTE: Prototype only, subject to change before this macro is
added to the ACPI specification. David E. Box.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a new directory heirarchy under the debugfs sunrpc/ directory:
sunrpc/
rpc_xprt/
<xprt id>/
Within that directory, we can put files that give info about the
xprts. We do have the (minor) problem that there is no succinct,
unique identifier for rpc_xprts. So we generate them synthetically
with a static atomic_t counter.
For now, this directory just holds an "info" file, but we may add
other files to it in the future.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
It's possible to get a dump of the RPC task queue by writing a value to
/proc/sys/sunrpc/rpc_debug. If you write any value to that file, you get
a dump of the RPC client task list into the log buffer. This is a rather
inconvenient interface however, and makes it hard to get immediate info
about the task queue.
Add a new directory hierarchy under debugfs:
sunrpc/
rpc_clnt/
<clientid>/
Within each clientid directory we create a new "tasks" file that will
dump info similar to what shows up in the log buffer, but with a few
small differences -- we avoid printing raw kernel addresses in favor of
symbolic names and the XID is also displayed.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
|
|
The task_collector mode (or "latency_injector", (C) Dan Willians) is an
optional I/O path in libsas that queues up scsi commands instead of
directly sending it to the hardware. It generall increases latencies
to in the optiomal case slightly reduce mmio traffic to the hardware.
Only the obsolete aic94xx driver and the mvsas driver allowed to use
it without recompiling the kernel, and most drivers didn't support it
at all.
Remove the giant blob of code to allow better optimizations for scsi-mq
in the future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add helper macros to iterate the current, or incoming set of planes
attached to a crtc. These helpers are only available for drivers
converted to use atomic-helpers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Squash in fixup from Rob to move the planemask iterator to
drm_crtc.h and document it. That one is needed by the atomic ioctl so
can't be in a helper library.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Chasing plane->state->crtc of planes that are *not* part of the same
atomic update is racy, making it incredibly awkward (or impossible) to
do something simple like iterate over all planes and figure out which
ones are attached to a crtc.
Solve this by adding a bitmask of currently attached planes in the
crtc-state.
Note that the transitional helpers do not maintain the plane_mask. But
they only support the legacy ioctls, which have sufficient brute-force
locking around plane updates that they can continue to loop over all
planes to see what is attached to a crtc the old way.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet:
- Drop comments about locking in set_crtc_for_plane since they're a
bit misleading - we already should hold lock for the current crtc.
- Also WARN_ON if get_state on the old crtc fails since that should
have been done already.
- Squash in fixup to check get_plane_state return value, reported by
Dan Carpenter and acked by Rob Clark.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This resolves linking problems with CONFIG_IPV6=n:
net/built-in.o: In function `redirect_tg6':
xt_REDIRECT.c:(.text+0x6d021): undefined reference to `nf_nat_redirect_ipv6'
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch exports the functions nft_reject_iphdr_validate and
nft_reject_ip6hdr_validate to use it in follow up patches.
These functions check if the IPv4/IPv6 header is correct.
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
add a __nfct_init_offset annotation member to struct nf_conn to make
it clear which members are covered by the memset when the conntrack
is allocated.
This avoids zeroing timer_list and ct_net; both are already inited
explicitly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OMAP mailbox driver and its existing clients (remoteproc
for OMAP4+) are adapted to use the generic mailbox framework.
The main changes for the adaptation are:
- The tasklet used for Tx is replaced with the state machine from
the generic mailbox framework. The workqueue used for processing
the received messages stays intact for minimizing the effects on
the OMAP mailbox clients.
- The existing exported client API, omap_mbox_get, omap_mbox_put and
omap_mbox_send_msg are deleted, as the framework provides equivalent
functionality. A OMAP-specific omap_mbox_request_channel is added
though to support non-DT way of requesting mailboxes.
- The OMAP mailbox driver is integrated with the mailbox framework
through the proper implementations of mbox_chan_ops, except for
.last_tx_done and .peek_data. The OMAP mailbox driver does not need
these ops, as it is completely interrupt driven.
- The OMAP mailbox driver uses a custom of_xlate controller ops that
allows phandles for the pargs specifier instead of indexing to avoid
any channel registration order dependencies.
- The new framework does not support multiple clients operating on a
single channel, so the reference counting logic is simplified.
- The remoteproc driver (current client) is adapted to use the new API.
The notifier callbacks used within this client is replaced with the
regular callbacks from the newer framework.
- The exported OMAP mailbox API are limited to omap_mbox_save_ctx,
omap_mbox_restore_ctx, omap_mbox_enable_irq & omap_mbox_disable_irq,
with the signature modified to take in the new mbox_chan handle instead
of the OMAP specific omap_mbox handle. The first 2 will be removed when
the OMAP mailbox driver is adapted to runtime_pm. The other exported
API omap_mbox_request_channel will be removed once existing legacy
users are converted to DT.
Signed-off-by: Suman Anna <s-anna@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
If the mailbox controller expects the payload is in place before
initiating the transmit, then it's impossible to reuse the list
maintained by core mailbox code currently. Maintaining another list
for sending the message in the controller seems totally unnecessary
as core mailbox library already provides that feature.
This patch introduces tx_prepare callback in mbox_client which
can be used by the core mailbox library before initiating the
transaction through mbox->ops->send_data. The client driver can
implement this callback to ensure the payload is copied to the
shared memory.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add the equivalents to pr_<level>_once.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a helper function that simplifies adding a
so-called single_open sequence file for device drivers. The
calling device driver needs to provide a read function and
a device pointer. The field struct seq_file::private will
reference the device pointer upon call to the read function
so the driver can obtain his data from it and do its task
of providing the file content using seq_printf() calls and
alike. Using this helper function also gets rid of the need
to specify file operations per debugfs file.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These members of the driver structure are not present.
Remove them from the kernel-doc.
Cc: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
