| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / miscdriver fixes from Greg KH:
"Here is a small set of char/misc and IIO driver fixes for 6.8-rc5.
Included in here are:
- lots of iio driver fixes for reported issues
- nvmem device naming fixup for reported problem
- interconnect driver fixes for reported issues
All of these have been in linux-next for a while with no reported the
issues (the nvmem patch was included in a different branch in
linux-next before sent to me for inclusion here)"
* tag 'char-misc-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
nvmem: include bit index in cell sysfs file name
iio: adc: ad4130: only set GPIO_CTRL if pin is unused
iio: adc: ad4130: zero-initialize clock init data
interconnect: qcom: x1e80100: Add missing ACV enable_mask
interconnect: qcom: sm8650: Use correct ACV enable_mask
iio: accel: bma400: Fix a compilation problem
iio: commom: st_sensors: ensure proper DMA alignment
iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
iio: move LIGHT_UVA and LIGHT_UVB to the end of iio_modifier
staging: iio: ad5933: fix type mismatch regression
iio: humidity: hdc3020: fix temperature offset
iio: adc: ad7091r8: Fix error code in ad7091r8_gpio_setup()
iio: adc: ad_sigma_delta: ensure proper DMA alignment
iio: imu: adis: ensure proper DMA alignment
iio: humidity: hdc3020: Add Makefile, Kconfig and MAINTAINERS entry
iio: imu: bno055: serdev requires REGMAP
iio: magnetometer: rm3100: add boundary check for the value read from RM3100_REG_TMRC
iio: pressure: bmp280: Add missing bmp085 to SPI id table
iio: core: fix memleak in iio_device_register_sysfs
interconnect: qcom: sm8550: Enable sync_state
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial fixes from Greg KH:
"Here are three small tty and serial driver fixes for 6.8-rc5:
- revert a 8250_pci1xxxx off-by-one change that was incorrect
- two changes to fix the transmit path of the mxs-auart driver,
fixing a regression in the 6.2 release
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: mxs-auart: fix tx
serial: core: introduce uart_port_tx_flags()
serial: 8250_pci1xxxx: partially revert off by one patch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are two small fixes for 6.8-rc5:
- thunderbolt to fix a reported issue on many platforms
- dwc3 driver revert of a commit that caused problems in -rc1
Both of these changes have been in linux-next for over a week with no
reported issues"
* tag 'usb-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: dwc3: Support EBC feature of DWC_usb31"
thunderbolt: Fix setting the CNS bit in ROUTER_CS_5
|
|
numa_fill_memblks() fills in the gaps in numa_meminfo memblks over a
physical address range. To do so, it first creates a list of existing
memblks that overlap that address range. The issue is that it is off
by one when comparing to the end of the address range, so memblks
that do not overlap are selected.
The impact of selecting a memblk that does not actually overlap is
that an existing memblk may be filled when the expected action is to
do nothing and return NUMA_NO_MEMBLK to the caller. The caller can
then add a new NUMA node and memblk.
Replace the broken open-coded search for address overlap with the
memblock helper memblock_addrs_overlap(). Update the kernel doc
and in code comments.
Suggested by: "Huang, Ying" <ying.huang@intel.com>
Fixes: 8f012db27c95 ("x86/numa: Introduce numa_fill_memblks()")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/10a3e6109c34c21a8dd4c513cf63df63481a2b07.1705085543.git.alison.schofield@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull block fixes from Jens Axboe:
"Just an nvme pull request via Keith:
- Fabrics connection error handling (Chaitanya)
- Use relaxed effects to reduce unnecessary queue freezes (Keith)"
* tag 'block-6.8-2024-02-16' of git://git.kernel.dk/linux:
nvmet: remove superfluous initialization
nvme: implement support for relaxed effects
nvme-fabrics: fix I/O connect error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix the #ifndef that didn't have the 'CONFIG_' prefix on
HAVE_DYNAMIC_FTRACE_WITH_REGS
The fix to have dynamic trampolines work with x86 broke arm64 as the
config used in the #ifdef was HAVE_DYNAMIC_FTRACE_WITH_REGS and not
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS which removed the fix that the
previous fix was to fix.
- Fix tracing_on state
The code to test if "tracing_on" is set incorrectly used
ring_buffer_record_is_on() which returns false if the ring buffer
isn't able to be written to.
But the ring buffer disable has several bits that disable it. One is
internal disabling which is used for resizing and other modifications
of the ring buffer. But the "tracing_on" user space visible flag
should only report if tracing is actually on and not internally
disabled, as this can cause confusion as writing "1" when it is
disabled will not enable it.
Instead use ring_buffer_record_is_set_on() which shows the user space
visible settings.
- Fix a false positive kmemleak on saved cmdlines
Now that the saved_cmdlines structure is allocated via alloc_page()
and not via kmalloc() it has become invisible to kmemleak. The
allocation done to one of its pointers was flagged as a dangling
allocation leak. Make kmemleak aware of this allocation and free.
- Fix synthetic event dynamic strings
An update that cleaned up the synthetic event code removed the return
value of trace_string(), and had it return zero instead of the
length, causing dynamic strings in the synthetic event to always have
zero size.
- Clean up documentation and header files for seq_buf
* tag 'trace-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
seq_buf: Fix kernel documentation
seq_buf: Don't use "proxy" headers
tracing/synthetic: Fix trace_string() return value
tracing: Inform kmemleak of saved_cmdlines allocation
tracing: Use ring_buffer_record_is_set_on() in tracer_tracing_is_on()
tracing: Fix HAVE_DYNAMIC_FTRACE_WITH_REGS ifdef
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of device-specific fixes. It became a bit bigger than
wished, but all look reasonably small and safe to apply.
- A few Cirrus Logic CS35L56 and CS42L43 driver fixes
- ASoC SOF fixes and workarounds
- Various ASoC Intel fixes
- Lots of HD-, USB-audio and AMD ACP quirks"
* tag 'sound-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (33 commits)
ALSA: usb-audio: More relaxed check of MIDI jack names
ALSA: hda/realtek: fix mute/micmute LED For HP mt645
ALSA: hda/realtek: cs35l41: Fix order and duplicates in quirks table
ALSA: hda/realtek: cs35l41: Fix device ID / model name
ALSA: hda/realtek: cs35l41: Add internal speaker support for ASUS UM3402 with missing DSD
ASoC: cs35l56: Workaround for ACPI with broken spk-id-gpios property
ALSA: hda: Add Lenovo Legion 7i gen7 sound quirk
ASoC: SOF: IPC3: fix message bounds on ipc ops
ASoC: SOF: ipc4-pcm: Workaround for crashed firmware on system suspend
ASoC: q6dsp: fix event handler prototype
ASoC: SOF: Intel: pci-lnl: Change the topology path to intel/sof-ipc4-tplg
ASoC: SOF: Intel: pci-tgl: Change the default paths and firmware names
ASoC: amd: yc: Fix non-functional mic on Lenovo 82UU
ASoC: rt5645: Add DMI quirk for inverted jack-detect on MeeGoPad T8
ASoC: rt5645: Make LattePanda board DMI match more precise
ASoC: SOF: amd: Fix locking in ACP IRQ handler
ASoC: rt5645: Fix deadlock in rt5645_jack_detect_work()
ASoC: Intel: cht_bsw_rt5645: Cleanup codec_name handling
ASoC: Intel: Boards: Fix NULL pointer deref in BYT/CHT boards
ASoC: cs35l56: Remove default from IRQ1_CFG register
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- add missing stubs for functions that are not built with GPIOLIB
disabled
* tag 'gpio-fixes-for-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: add gpio_device_get_label() stub for !GPIOLIB
gpiolib: add gpio_device_get_base() stub for !GPIOLIB
gpiolib: add gpiod_to_gpio_device() stub for !GPIOLIB
|
|
Before this change, generation of the list of MDB events to replay
would race against the creation of new group memberships, either from
the IGMP/MLD snooping logic or from user configuration.
While new memberships are immediately visible to walkers of
br->mdb_list, the notification of their existence to switchdev event
subscribers is deferred until a later point in time. So if a replay
list was generated during a time that overlapped with such a window,
it would also contain a replay of the not-yet-delivered event.
The driver would thus receive two copies of what the bridge internally
considered to be one single event. On destruction of the bridge, only
a single membership deletion event was therefore sent. As a
consequence of this, drivers which reference count memberships (at
least DSA), would be left with orphan groups in their hardware
database when the bridge was destroyed.
This is only an issue when replaying additions. While deletion events
may still be pending on the deferred queue, they will already have
been removed from br->mdb_list, so no duplicates can be generated in
that scenario.
To a user this meant that old group memberships, from a bridge in
which a port was previously attached, could be reanimated (in
hardware) when the port joined a new bridge, without the new bridge's
knowledge.
For example, on an mv88e6xxx system, create a snooping bridge and
immediately add a port to it:
root@infix-06-0b-00:~$ ip link add dev br0 up type bridge mcast_snooping 1 && \
> ip link set dev x3 up master br0
And then destroy the bridge:
root@infix-06-0b-00:~$ ip link del dev br0
root@infix-06-0b-00:~$ mvls atu
ADDRESS FID STATE Q F 0 1 2 3 4 5 6 7 8 9 a
DEV:0 Marvell 88E6393X
33:33:00:00:00:6a 1 static - - 0 . . . . . . . . . .
33:33:ff:87:e4:3f 1 static - - 0 . . . . . . . . . .
ff:ff:ff:ff:ff:ff 1 static - - 0 1 2 3 4 5 6 7 8 9 a
root@infix-06-0b-00:~$
The two IPv6 groups remain in the hardware database because the
port (x3) is notified of the host's membership twice: once via the
original event and once via a replay. Since only a single delete
notification is sent, the count remains at 1 when the bridge is
destroyed.
Then add the same port (or another port belonging to the same hardware
domain) to a new bridge, this time with snooping disabled:
root@infix-06-0b-00:~$ ip link add dev br1 up type bridge mcast_snooping 0 && \
> ip link set dev x3 up master br1
All multicast, including the two IPv6 groups from br0, should now be
flooded, according to the policy of br1. But instead the old
memberships are still active in the hardware database, causing the
switch to only forward traffic to those groups towards the CPU (port
0).
Eliminate the race in two steps:
1. Grab the write-side lock of the MDB while generating the replay
list.
This prevents new memberships from showing up while we are generating
the replay list. But it leaves the scenario in which a deferred event
was already generated, but not delivered, before we grabbed the
lock. Therefore:
2. Make sure that no deferred version of a replay event is already
enqueued to the switchdev deferred queue, before adding it to the
replay list, when replaying additions.
Fixes: 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stanislaw Gruszka says:
====================
thermal/netlink/intel_hfi: Enable HFI feature only when required
The patchset introduces a new genetlink family bind/unbind callbacks
and thermal/netlink notifications, which allow drivers to send netlink
multicast events based on the presence of actual user-space consumers.
This functionality optimizes resource usage by allowing disabling
of features when not needed.
v1: https://lore.kernel.org/linux-pm/20240131120535.933424-1-stanislaw.gruszka@linux.intel.com//
v2: https://lore.kernel.org/linux-pm/20240206133605.1518373-1-stanislaw.gruszka@linux.intel.com/
v3: https://lore.kernel.org/linux-pm/20240209120625.1775017-1-stanislaw.gruszka@linux.intel.com/
====================
Link: https://lore.kernel.org/r/20240212161615.161935-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add genetlink family bind()/unbind() callbacks when adding/removing
multicast group to/from netlink client socket via setsockopt() or
bind() syscall.
They can be used to track if consumers of netlink multicast messages
emerge or disappear. Thus, a client implementing callbacks, can now
send events only when there are active consumers, preventing unnecessary
work when none exist.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240212161615.161935-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c92a6b5d6335 ("scsi: core: Query VPD size before getting full
page") removed the logic which checks whether a VPD page is present on
the supported pages list before asking for the page itself. That was
done because SPC helpfully states "The Supported VPD Pages VPD page
list may or may not include all the VPD pages that are able to be
returned by the device server". Testing had revealed a few devices
that supported some of the 0xBn pages but didn't actually list them in
page 0.
Julian Sikorski bisected a problem with his drive resetting during
discovery to the commit above. As it turns out, this particular drive
firmware will crash if we attempt to fetch page 0xB9.
Various approaches were attempted to work around this. In the end,
reinstating the logic that consults VPD page 0 before fetching any
other page was the path of least resistance. A firmware update for the
devices which originally compelled us to remove the check has since
been released.
Link: https://lore.kernel.org/r/20240214221411.2888112-1-martin.petersen@oracle.com
Fixes: c92a6b5d6335 ("scsi: core: Query VPD size before getting full page")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Reviewed-by: Lee Duncan <lee.duncan@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from can, wireless and netfilter.
Current release - regressions:
- af_unix: fix task hung while purging oob_skb in GC
- pds_core: do not try to run health-thread in VF path
Current release - new code bugs:
- sched: act_mirred: don't zero blockid when net device is being
deleted
Previous releases - regressions:
- netfilter:
- nat: restore default DNAT behavior
- nf_tables: fix bidirectional offload, broken when unidirectional
offload support was added
- openvswitch: limit the number of recursions from action sets
- eth: i40e: do not allow untrusted VF to remove administratively set
MAC address
Previous releases - always broken:
- tls: fix races and bugs in use of async crypto
- mptcp: prevent data races on some of the main socket fields, fix
races in fastopen handling
- dpll: fix possible deadlock during netlink dump operation
- dsa: lan966x: fix crash when adding interface under a lag when some
of the ports are disabled
- can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
Misc:
- a handful of fixes and reliability improvements for selftests
- fix sysfs documentation missing net/ in paths
- finish the work of squashing the missing MODULE_DESCRIPTION()
warnings in networking"
* tag 'net-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
net: fill in MODULE_DESCRIPTION()s for missing arcnet
net: fill in MODULE_DESCRIPTION()s for mdio_devres
net: fill in MODULE_DESCRIPTION()s for ppp
net: fill in MODULE_DESCRIPTION()s for fddik/skfp
net: fill in MODULE_DESCRIPTION()s for plip
net: fill in MODULE_DESCRIPTION()s for ieee802154/fakelb
net: fill in MODULE_DESCRIPTION()s for xen-netback
net: ravb: Count packets instead of descriptors in GbEth RX path
pppoe: Fix memory leak in pppoe_sendmsg()
net: sctp: fix skb leak in sctp_inq_free()
net: bcmasp: Handle RX buffer allocation failure
net-timestamp: make sk_tskey more predictable in error path
selftests: tls: increase the wait in poll_partial_rec_async
ice: Add check for lport extraction to LAG init
netfilter: nf_tables: fix bidirectional offload regression
netfilter: nat: restore default DNAT behavior
netfilter: nft_set_pipapo: fix missing : in kdoc
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
can: netlink: Fix TDCO calculation using the old data bittiming
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Fixes and simple cleanups:
- use a proper flexible array instead of a one-element array in order
to avoid array-bounds sanitizer errors
- add NULL pointer checks after allocating memory
- use memdup_array_user() instead of open-coding it
- fix a rare race condition in Xen event channel allocation code
- make struct bus_type instances const
- make kerneldoc inline comments match reality"
* tag 'for-linus-6.8a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: close evtchn after mapping cleanup
xen/gntalloc: Replace UAPI 1-element array
xen: balloon: make balloon_subsys const
xen: pcpu: make xen_pcpu_subsys const
xen/privcmd: Use memdup_array_user() in alloc_ioreq()
x86/xen: Add some null pointer checking to smp.c
xen/xenbus: document will_handle argument for xenbus_watch_path()
|
|
In commit 4356e9f841f7 ("work around gcc bugs with 'asm goto' with
outputs") I did the gcc workaround unconditionally, because the cause of
the bad code generation wasn't entirely clear.
In the meantime, Jakub Jelinek debugged the issue, and has come up with
a fix in gcc [2], which also got backported to the still maintained
branches of gcc-11, gcc-12 and gcc-13.
Note that while the fix technically wasn't in the original gcc-14
branch, Jakub says:
"while it is true that no GCC 14 snapshots until today (or whenever the
fix will be committed) have the fix, for GCC trunk it is up to the
distros to use the latest snapshot if they use it at all and would
allow better testing of the kernel code without the workaround, so
that if there are other issues they won't be discovered years later.
Most userland code doesn't actually use asm goto with outputs..."
so we will consider gcc-14 to be fixed - if somebody is using gcc
snapshots of the gcc-14 before the fix, they should upgrade.
Note that while the bug goes back to gcc-11, in practice other gcc
changes seem to have effectively hidden it since gcc-12.1 as per a
bisect by Jakub. So even a gcc-14 snapshot without the fix likely
doesn't show actual problems.
Also, make the default 'asm_goto_output()' macro mark the asm as
volatile by hand, because of an unrelated gcc issue [1] where it doesn't
match the documented behavior ("asm goto is always volatile").
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=103979 [1]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=113921 [2]
Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/
Requested-by: Jakub Jelinek <jakub@redhat.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Andrew Pinski <quic_apinski@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are plenty of issues with the kernel documentation here:
- misspelled word "sequence"
- different style of returned value descriptions
- missed Return sections
- unaligned style of ASCII / NUL-terminated / etc
- wrong function references
Fix all these.
Link: https://lkml.kernel.org/r/20240215152506.598340-1-andriy.shevchenko@linux.intel.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Link: https://lkml.kernel.org/r/20240215142255.400264-1-andriy.shevchenko@linux.intel.com
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
In RFC 8981, REGEN_ADVANCE cannot be less than 2 seconds, and the RFC
does not permit the creation of temporary addresses with lifetimes
shorter than that:
> When processing a Router Advertisement with a
> Prefix Information option carrying a prefix for the purposes of
> address autoconfiguration (i.e., the A bit is set), the host MUST
> perform the following steps:
> 5. A temporary address is created only if this calculated preferred
> lifetime is greater than REGEN_ADVANCE time units.
However, some users want to change their IPv6 address as frequently as
possible regardless of the RFC's arbitrary minimum lifetime. For the
benefit of those users, add a regen_min_advance sysctl parameter that
can be set to below or above 2 seconds.
Link: https://datatracker.ietf.org/doc/html/rfc8981
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since commit d492cc2573a0 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the mdio_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-mdio-v1-1-f9e799da7fda@marliere.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Even if that's the same as IEEE80211_MAX_SSID_LEN, we really
should just use IEEE80211_MAX_MESH_ID_LEN for mesh, rather
than having the BUILD_BUG_ON()s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- Fix for broken ipv6 checksums
- Fix handling of exceptions in delay slots
* tag 'mips-fixes_6.8_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mm/memory: Use exception ip to search exception tables
MIPS: Clear Cause.BD in instruction_pointer_set
ptrace: Introduce exception_ip arch hook
MIPS: Add 'memory' clobber to csum_ipv6_magic() inline assembler
|
|
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
IIO: 1st set of fixes for the 6.8 cycle
Usual mixed bag of issues introduced this cycle and fixes for long term
issues that have been identified recently + one case where I messed up
a merge resolution and dropped the build file changes.
Most important is the userspace ABI fix for the iio_modifier enum
where we accidentally added new entries in the middle rather than at
the end.
IIO Core
- Close a memory leak in an error path.
- Move LIGHT_UVA and LIGHT_UVB definitions to end of the iio_modifier
enum to avoid breaking older userspace. (not yet in a released kernel
thankfully).
adi,adis
- Fix a DMA buffer alignment issue that was missing in series that fixed
these across IIO.
adi,ad-sigma-delta
- Fix a DMA buffer alignment issue that was missing in series that fixed
these across IIO.
adi,ad4130
- Zero init remaining fields of clock init data.
- Only set GPIO control bits on pins that aren't in use for anything else.
adi,ad5933
- Fix an old bug due to type mismatch. This is a rare device so good to
get some new test coverage.
adi,ad7091r
- Use right variable for an error return code.
bosch,bma400
- Add missing CONFIG_REGMAP_I2C dependency.
bosch,bmp280:
- Add missing bmp085 ID to the SPI table to avoid mismatch with the
of_device_id table.
hid-sensors:
- Avoid returning an error for timestamp read back that succeeds.
pni,rm3100
- Check value read from RM31000_REG_TMRC register is valid before using
it. Hardening to avoid a real world issue seen on some faulty hardware.
st,st-sensors
- Fix a DMA buffer alignment issue that was missing in series that fixed
these across IIO.
ti,hdc3020
- Add missing Kconfig and Makefile entrees accidentally dropped when patches
were applied.
- Fix wrong temperature offset (negated)
* tag 'iio-fixes-for-6.8a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ad4130: only set GPIO_CTRL if pin is unused
iio: adc: ad4130: zero-initialize clock init data
iio: accel: bma400: Fix a compilation problem
iio: commom: st_sensors: ensure proper DMA alignment
iio: hid-sensor-als: Return 0 for HID_USAGE_SENSOR_TIME_TIMESTAMP
iio: move LIGHT_UVA and LIGHT_UVB to the end of iio_modifier
staging: iio: ad5933: fix type mismatch regression
iio: humidity: hdc3020: fix temperature offset
iio: adc: ad7091r8: Fix error code in ad7091r8_gpio_setup()
iio: adc: ad_sigma_delta: ensure proper DMA alignment
iio: imu: adis: ensure proper DMA alignment
iio: humidity: hdc3020: Add Makefile, Kconfig and MAINTAINERS entry
iio: imu: bno055: serdev requires REGMAP
iio: magnetometer: rm3100: add boundary check for the value read from RM3100_REG_TMRC
iio: pressure: bmp280: Add missing bmp085 to SPI id table
iio: core: fix memleak in iio_device_register_sysfs
|
|
dev_base_lock is not needed anymore, all remaining users also hold RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_base_lock is going away, add netdev_set_operstate() helper
so that hsr does not have to know core internals.
Remove dev_base_lock acquisition from rfc2863_policy()
v3: use an "unsigned int" for dev->operstate,
so that try_cmpxchg() can work on all arches.
( https://lore.kernel.org/oe-kbuild-all/202402081918.OLyGaea3-lkp@intel.com/ )
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepares things so that dev->reg_state reads can be lockless,
by adding WRITE_ONCE() on write side.
READ_ONCE()/WRITE_ONCE() do not support bitfields.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an ioctl for getting and setting epoll_params. User programs can use
this ioctl to get and set the busy poll usec time, packet budget, and
prefer busy poll params for a specific epoll context.
Parameters are limited:
- busy_poll_usecs is limited to <= s32_max
- busy_poll_budget is limited to <= NAPI_POLL_WEIGHT by unprivileged
users (!capable(CAP_NET_ADMIN))
- prefer_busy_poll must be 0 or 1
- __pad must be 0
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-6.9-20240213
this is a pull request of 23 patches for net-next/master.
The first patch is by Nicolas Maier and targets the CAN Broadcast
Manager (bcm), it adds message flags to distinguish between own local
and remote traffic.
Oliver Hartkopp contributes a patch for the CAN ISOTP protocol that
adds dynamic flow control parameters.
Stefan Mätje's patch series add support for the esd PCIe/402 CAN
interface family.
Markus Schneider-Pargmann contributes 14 patches for the m_can to
optimize for the SPI attached tcan4x5x controller.
A patch by Vincent Mailhol replaces Wolfgang Grandegger by Vincent
Mailhol as the CAN drivers Co-Maintainer.
Jimmy Assarsson's patch add support for the Kvaser M.2 PCIe 4xCAN
adapter.
A patch by Daniil Dulov removed a redundant NULL check in the softing
driver.
Oliver Hartkopp contributes a patch to add CANXL virtual CAN network
identifier support.
A patch by myself removes Naga Sureshkumar Relli as the maintainer of
the xilinx_can driver, as their email bounces.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rely on skb_pp_cow_data utility routine and remove duplicated code.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/029cc14cce41cb242ee7efdcf32acc81f1ce4e9f.1707729884.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similar to native xdp, do not always linearize the skb in
netif_receive_generic_xdp routine but create a non-linear xdp_buff to be
processed by the eBPF program. This allow to add multi-buffer support
for xdp running in generic mode.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/1044d6412b1c3e95b40d34993fd5f37cd2f319fd.1707729884.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netif_receive_generic_xdp
Rely on skb pointer reference instead of the skb pointer in do_xdp_generic
and netif_receive_generic_xdp routine signatures.
This is a preliminary patch to add multi-buff support for xdp running in
generic mode where we will need to reallocate the skb to avoid
linearization and we will need to make it visible to do_xdp_generic()
caller.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c09415b1f48c8620ef4d76deed35050a7bddf7c2.1707729884.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce generic percpu page_pools allocator.
Moreover add page_pool_create_percpu() and cpuid filed in page_pool struct
in order to recycle the page in the page_pool "hot" cache if
napi_pp_put_page() is running on the same cpu.
This is a preliminary patch to add xdp multi-buff support for xdp running
in generic mode.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Toke Hoiland-Jorgensen <toke@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/80bc4285228b6f4220cd03de1999d86e46e3fcbd.1707729884.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return result of btf_get_prog_ctx_type() is never used and callers only
check NULL vs non-NULL case to determine if given type matches expected
PTR_TO_CTX type. So rename function to `btf_is_prog_ctx_type()` and
return a simple true/false. We'll use this simpler interface to handle
kprobe program type's special typedef case in the next patch.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240212233221.2575350-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Originally, this patch removed a redundant check in
BPF_CGROUP_RUN_PROG_INET_EGRESS, as the check was already being done in
the function it called, __cgroup_bpf_run_filter_skb. For v2, it was
reccomended that I remove the check from __cgroup_bpf_run_filter_skb,
and add the checks to the other macro that calls that function,
BPF_CGROUP_RUN_PROG_INET_INGRESS.
To sum it up, checking that the socket exists and that it is a full
socket is now part of both macros BPF_CGROUP_RUN_PROG_INET_EGRESS and
BPF_CGROUP_RUN_PROG_INET_INGRESS, and it is no longer part of the
function they call, __cgroup_bpf_run_filter_skb.
v3->v4: Fixed weird merge conflict.
v2->v3: Sent to bpf-next instead of generic patch
v1->v2: Addressed feedback about where check should be removed.
Signed-off-by: Oliver Crumrine <ozlinuxc@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/7lv62yiyvmj5a7eozv2iznglpkydkdfancgmbhiptrgvgan5sy@3fl3onchgdz3
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Collect argument information from the type information of stub functions to
mark arguments of BPF struct_ops programs with PTR_MAYBE_NULL if they are
nullable. A nullable argument is annotated by suffixing "__nullable" at
the argument name of stub function.
For nullable arguments, this patch sets a struct bpf_ctx_arg_aux to label
their reg_type with PTR_TO_BTF_ID | PTR_TRUSTED | PTR_MAYBE_NULL. This
makes the verifier to check programs and ensure that they properly check
the pointer. The programs should check if the pointer is null before
accessing the pointed memory.
The implementer of a struct_ops type should annotate the arguments that can
be null. The implementer should define a stub function (empty) as a
placeholder for each defined operator. The name of a stub function should
be in the pattern "<st_op_type>__<operator name>". For example, for
test_maybe_null of struct bpf_testmod_ops, it's stub function name should
be "bpf_testmod_ops__test_maybe_null". You mark an argument nullable by
suffixing the argument name with "__nullable" at the stub function.
Since we already has stub functions for kCFI, we just reuse these stub
functions with the naming convention mentioned earlier. These stub
functions with the naming convention is only required if there are nullable
arguments to annotate. For functions having not nullable arguments, stub
functions are not necessary for the purpose of this patch.
This patch will prepare a list of struct bpf_ctx_arg_aux, aka arg_info, for
each member field of a struct_ops type. "arg_info" will be assigned to
"prog->aux->ctx_arg_info" of BPF struct_ops programs in
check_struct_ops_btf_id() so that it can be used by btf_ctx_access() later
to set reg_type properly for the verifier.
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240209023750.1153905-4-thinker.li@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Move __kfunc_param_match_suffix() to btf.c and rename it as
btf_param_match_suffix(). It can be reused by bpf_struct_ops later.
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240209023750.1153905-3-thinker.li@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Enable the providers to use types defined in a module instead of in the
kernel (btf_vmlinux).
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240209023750.1153905-2-thinker.li@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Currently tracing is supposed not to allow for bpf_spin_{lock,unlock}()
helper calls. This is to prevent deadlock for the following cases:
- there is a prog (prog-A) calling bpf_spin_{lock,unlock}().
- there is a tracing program (prog-B), e.g., fentry, attached
to bpf_spin_lock() and/or bpf_spin_unlock().
- prog-B calls bpf_spin_{lock,unlock}().
For such a case, when prog-A calls bpf_spin_{lock,unlock}(),
a deadlock will happen.
The related source codes are below in kernel/bpf/helpers.c:
notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
notrace is supposed to prevent fentry prog from attaching to
bpf_spin_{lock,unlock}().
But actually this is not the case and fentry prog can successfully
attached to bpf_spin_lock(). Siddharth Chintamaneni reported
the issue in [1]. The following is the macro definition for
above BPF_CALL_1:
#define BPF_CALL_x(x, name, ...) \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)) \
{ \
return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
} \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
#define BPF_CALL_1(name, ...) BPF_CALL_x(1, name, __VA_ARGS__)
The notrace attribute is actually applied to the static always_inline function
____bpf_spin_{lock,unlock}(). The actual callback function
bpf_spin_{lock,unlock}() is not marked with notrace, hence
allowing fentry prog to attach to two helpers, and this
may cause the above mentioned deadlock. Siddharth Chintamaneni
actually has a reproducer in [2].
To fix the issue, a new macro NOTRACE_BPF_CALL_1 is introduced which
will add notrace attribute to the original function instead of
the hidden always_inline function and this fixed the problem.
[1] https://lore.kernel.org/bpf/CAE5sdEigPnoGrzN8WU7Tx-h-iFuMZgW06qp0KHWtpvoXxf1OAQ@mail.gmail.com/
[2] https://lore.kernel.org/bpf/CAE5sdEg6yUc_Jz50AnUXEEUh6O73yQ1Z6NV2srJnef0ZrQkZew@mail.gmail.com/
Fixes: d83525ca62cf ("bpf: introduce bpf_spin_lock")
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240207070102.335167-1-yonghong.song@linux.dev
|
|
NVM Express TP4167 provides a way for controllers to report a relaxed
execution constraint. Specifically, it notifies of exclusivity for IO
vs. admin commands instead of grouping these together. If set, then we
don't need to freeze IO in order to execute that admin command. The
freezing distrupts IO processes, so it's nice to avoid that if the
controller tells us it's not necessary.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
CAN XL data frames contain an 8-bit virtual CAN network identifier (VCID).
A VCID value of zero represents an 'untagged' CAN XL frame.
To receive and send these optional VCIDs via CAN_RAW sockets a new socket
option CAN_RAW_XL_VCID_OPTS is introduced to define/access VCID content:
- tx: set the outgoing VCID value by the kernel (one fixed 8-bit value)
- tx: pass through VCID values from the user space (e.g. for traffic replay)
- rx: apply VCID receive filter (value/mask) to be passed to the user space
With the 'tx pass through' option CAN_RAW_XL_VCID_TX_PASS all valid VCID
values can be sent, e.g. to replay full qualified CAN XL traffic.
The VCID value provided for the CAN_RAW_XL_VCID_TX_SET option will
override the VCID value in the struct canxl_frame.prio defined for
CAN_RAW_XL_VCID_TX_PASS when both flags are set.
With a rx_vcid_mask of zero all possible VCID values (0x00 - 0xFF) are
passed to the user space when the CAN_RAW_XL_VCID_RX_FILTER flag is set.
Without this flag only untagged CAN XL frames (VCID = 0x00) are delivered
to the user space (default).
The 8-bit VCID is stored inside the CAN XL prio element (only in CAN XL
frames!) to not interfere with other CAN content or the CAN filters
provided by the CAN_RAW sockets and kernel infrastruture.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20240212213550.18516-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add empty stub of gpio_device_get_label() when GPIOLIB is not enabled.
Cc: <stable@vger.kernel.org>
Fixes: d1f7728259ef ("gpiolib: provide gpio_device_get_label()")
Suggested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add empty stub of gpio_device_get_base() when GPIOLIB is not enabled.
Cc: <stable@vger.kernel.org>
Fixes: 8c85a102fc4e ("gpiolib: provide gpio_device_get_base()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add empty stub of gpiod_to_gpio_device() when GPIOLIB is not enabled.
Cc: <stable@vger.kernel.org>
Fixes: 370232d096e3 ("gpiolib: provide gpiod_to_gpio_device()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Without changing the structure size (since it is UAPI), add a proper
flexible array member, and reference it in the kernel so that it will
not be trip the array-bounds sanitizer[1].
Link: https://github.com/KSPP/linux/issues/113 [1]
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: xen-devel@lists.xenproject.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240206170320.work.437-kees@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Set scope automatically in ip_route_output_ports() (using the socket
SOCK_LOCALROUTE flag). This way, callers don't have to overload the
tos with the RTO_ONLINK flag, like RT_CONN_FLAGS() does.
For callers that don't pass a struct sock, this doesn't change anything
as the scope is still set to RT_SCOPE_UNIVERSE when sk is NULL.
Callers that passed a struct sock and used RT_CONN_FLAGS(sk) or
RT_CONN_FLAGS_TOS(sk, tos) for the tos are modified to use
ip_sock_tos(sk) and RT_TOS(tos) respectively, as overloading tos with
the RTO_ONLINK flag now becomes unnecessary.
In drivers/net/amt.c, all ip_route_output_ports() calls use a 0 tos
parameter, ignoring the SOCK_LOCALROUTE flag of the socket. But the sk
parameter is a kernel socket, which doesn't have any configuration path
for setting SOCK_LOCALROUTE anyway. Therefore, ip_route_output_ports()
will continue to initialise scope with RT_SCOPE_UNIVERSE and amt.c
doesn't need to be modified.
Also, remove RT_CONN_FLAGS() and RT_CONN_FLAGS_TOS() from route.h as
these macros are now unused.
The objective is to eventually remove RTO_ONLINK entirely to allow
converting ->flowi4_tos to dscp_t. This will ensure proper isolation
between the DSCP and ECN bits, thus minimising the risk of introducing
bugs where TOS values interfere with ECN.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/dacfd2ab40685e20959ab7b53c427595ba229e7d.1707496938.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On architectures with delay slot, architecture level instruction
pointer (or program counter) in pt_regs may differ from where
exception was triggered.
Introduce exception_ip hook to invoke architecture code and determine
actual instruction pointer to the exception.
Link: https://lore.kernel.org/lkml/00d1b813-c55f-4365-8d81-d70258e10b16@app.fastmail.com/
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add to cfg80211_wowlan_wakeup another wakeup reason -
unprot_deauth_disassoc.
To be set to true if the woke up was due to an
unprotected deauth or disassoc frame in MFP.
In that case report WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.a3d739850d03.I8f52a21c4f36d1af1f8068bed79e2f9cbf8289ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a report reason for waking up due to an unprotected
deauth/disassoc when MFP is used.
If setting wowlan to wake on disconnection, and an unprotected
deatuh/disassoc arrived (in MFP), some drivers might want to
report wakeup due to unprotected deauth/disassoc, rather than
dissassociation. Add support for that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.8dc9ad531a17.I7f8e926adf927f762e11aaa3458f6354665c7fc5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the hardware supports a disabled channel, it may in
some cases be possible to use monitor mode (without any
transmit) on it when it's otherwise disabled. Add a new
channel flag IEEE80211_CHAN_CAN_MONITOR that makes it
possible for a driver to indicate such a thing.
Make it per channel so drivers could have a choice with
it, perhaps it's only possible on some channels, perhaps
some channels are not supported at all, but still there
and marked disabled.
In _nl80211_parse_chandef() simplify the code and check
only for an unknown channel, _cfg80211_chandef_usable()
will later check for IEEE80211_CHAN_DISABLED anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.87fad3a21a09.I9116b2fdc2e2c9fd59a9273a64db7fcb41fc0328@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
