| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Support for the power-domains on rk3368 and a fix for
a wrong handling of for_each_available_child_of_node.
* tag 'v4.6-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: power-domain: fix err handle while probing
soc: rockchip: power-domain: Modify power domain driver for rk3368
dt-bindings: modify document of Rockchip power domains
dt-bindings: add power-domain header for RK3368 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt
Highlights:
-----------
- Add DMA controller node to stm32f429 MCU
- Add pinctrl & gpio nodes to stm32f429 MCU
- Remap stm32429-eval board SD-Ram to 0x0 for performance boost
* tag 'stm32-dt-for-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
ARM: dts: stm32f429: Boost perfs by remapping SDRAM Bank 1 to 0x0
ARM: dts: Add leds support to STM32F429 boards
ARM: dts: Add USART1 pin config to STM32F429 boards
ARM: dts: Add pinctrl node to STM32F429
includes: dt-bindings: Add STM32F429 pinctrl DT bindings
ARM: dts: Add STM32 DMA support for STM32F429 MCU
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The fix in 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes: 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.")
Fixes: c6c33454072f ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for DCBNL IEEE get/set max rate.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add access functions to set and query a physical port PFC
(Priority Flow Control) parameters.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the device physical port access functions are implemented in the
port.c file.
We just extract the exposure of these functions from driver.h into a
dedicated header file called port.h.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This exposes the firmware's implementation of EFI_RNG_PROTOCOL via a new
function efi_get_random_bytes().
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
ACPICA commit 181f56605a771e0b91e24b0648d2565ca70bea20
This is used as a purely infomation message, without module name
and line number information. Therefore, these arguments are
not needed and they are unnecessary overhead.
Arguments are removed.
ACPICA BZ 872.
Link: https://github.com/acpica/acpica/commit/181f5660
Link: https://bugs.acpica.org/show_bug.cgi?id=872
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
No more users for it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Helper for finding the type based on name. Useful if the
type needs to be determined based on device property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[modify rfkill_types array and BUILD_BUG_ON to not cause errors]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
I noticed the comment label 'wait_event' was wrong.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1456234768-24933-1-git-send-email-shorne@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Today, the supplicant will add the RRM capabilities
Information Element in the association request only if
Quiet period is supported (NL80211_FEATURE_QUIET).
Quiet is one of many RRM features, and there are other RRM
features that are not related to Quiet (e.g. neighbor
report). Therefore, requiring Quiet to enable RRM is too
restrictive.
Some of the features, like neighbor report, can be
supported by user space without any help from the kernel.
Hence adding the RRM capabilities IE to association request
should be the sole user space's decision.
Removing the RRM dependency on Quiet in the driver solves
this problem, but using an old driver with a user space
tool that would not require Quiet feature would be
problematic: the user space would add NL80211_ATTR_USE_RRM
in the association request even if the kernel doesn't
advertize NL80211_FEATURE_QUIET and the association would
be denied by the kernel.
This solution adds a global RRM capability, that tells user
space that it can request RRM capabilities IE publishment
without any specific feature support in the kernel.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Provide an interface to the lower level driver to set the VHT
MU-MIMO data. This is needed for example when there is an update
of the group data during low power state, where the management
frame will not be passed to the host at all.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the PNs of all the tx keys are now tracked in the public
part of the key struct (with atomic counter), we no longer
need these functions.
dvm and vt665{5,6} are currently the only users of these functions,
so update them accordingly.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).
Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.
Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.
The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.
Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If any frames are dropped that are part of a BA session, the reorder
buffer will "indefinitely" (until the timeout) wait for them to come
in (or a BAR moving the window) and won't release frames after them.
This means it isn't possible to filter frames within a BA session in
firmware.
Introduce an API function that allows such filtering. Calling this
function will move the BA window forward to the new SSN, and allows
marking frames after the SSN as having been filtered, so any future
reordering activity will release frames while skipping the holes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow drivers to make more educated
decisions whether to defer transmission or not.
Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.
It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers/devices without their own rate control algorithm can get the
information what rates they should use from either the radiotap header of
injected frames or from the rate control algorithm. But the parsing of the
legacy rate information from the radiotap header was removed in commit
e6a9854b05c1 ("mac80211/drivers: rewrite the rate control API").
The removal of this feature heavily reduced the usefulness of frame
injection when wanting to simulate specific transmission behavior. Having
rate parsing together with MCS rates and retry support allows a fine
grained selection of the tx behavior of injected frames for these kind of
tests.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a note to userspace on the effect of RFKILL_OP_CHANGE_ALL also
updating the default state for hotplugged devices.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
[reword a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When suspended while polling is paused, polling will erroneously
resume at resume time. Fix this by tracking pause and suspend in
separate state variable and adding the necessary checks.
Clarify the documentation on this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make the addr parameter const in SET_IEEE80211_PERM_ADDR() to save
clients from having to cast away a const qualifier.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.
In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers offload some frames internally (e.g.
AddBa). Reporting such frames to mac80211 would
only confuse MLME. However it would be useful to
be able to pass such frames to monitor interfaces
for sniffing purposes, e.g. when running AP +
monitor.
To do that allow drivers to tell mac80211 whether
a given frame should be:
- processed but not delivered to any monitor vif
- not processed but delievered to monitor vifs
only
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enable driver to manage the reordering logic itself.
This is needed for example for the iwlwifi driver that
will support hardware assisted reordering.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Andreas Irestål <andire@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because there are neither uses nor intended uses for the
rcu_user_hooks_switch() function that was orginally intended
for nohz use, this commit removes it.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
SRCU uses per-CPU variables, and DEFINE_STATIC_SRCU() uses a static
per-CPU variable. However, per-CPU variables have significant
restrictions, for example, names of per-CPU variables must be globally
unique, even if declared static. These restrictions carry over to
DEFINE_STATIC_SRCU(), and this commit therefore documents these
restrictions.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
|
|
irq_common_data::state_use_accessors is not designed for public use.
Therefore make it private so that people who write code accessing it
directly will get blamed by sparse. Also #undef the macro
__irqd_to_state after used in header files, so that the macro can't be
misused.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
In C programming language, we don't have a easy way to privatize a
member of a structure. However in kernel, sometimes there is a need to
privatize a member in case of potential bugs or misuses.
Fortunately, the noderef attribute of sparse is a way to privatize a
member, as by defining a member as noderef, the address-of operator on
the member will produce a noderef pointer to that member, and if anyone
wants to dereference that kind of pointers to read or modify the member,
sparse will yell.
Based on this, __private modifier and related operation ACCESS_PRIVATE()
are introduced, which could help detect undesigned public uses of
private members of structs. Here is an example of sparse's output if it
detect an undersigned public use:
| kernel/rcu/tree.c:4453:25: warning: incorrect type in argument 1 (different modifiers)
| kernel/rcu/tree.c:4453:25: expected struct raw_spinlock [usertype] *lock
| kernel/rcu/tree.c:4453:25: got struct raw_spinlock [noderef] *<noident>
Also, this patch improves compiler.h a little bit by adding comments for
"#else" and "#endif".
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
If a device needs to be rescanned the device_handler might need
to be rechecked, too.
So add a 'rescan' callback to the device handler and call it
upon scsi_rescan_device(). The rescan callback will be invoked
from the Unit Attention handling of ASC/ASCQ 3F 03
(INQUIRY DATA HAS CHANGED).
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new blacklist flag BLIST_SYNC_ALUA to instruct the
alua device handler to use synchronous command submission
for ALUA commands.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The port group needs to be a separate structure as several
LUNs might belong to the same group.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The hpsa driver uses this function to cleanup inquiry data. Our new pqi
driver will also use this function. This function was copied into both
drivers.
This patch exports sanitize_inquiry_string so the hpsa and the pqi
drivers can use this function directly.
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
iscsi_port_speed and iscsi_port_speed_names have new entries for
25Gbps and 40Gbps link speeds.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The original format of these commands from the "NVDIMM DSM Interface
Example" [1] are superseded by the ACPI 6.1 definition of the "NVDIMM Root
Device _DSMs" [2].
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
[2]: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
"9.20.7 NVDIMM Root Device _DSMs"
Changes include:
1/ New 'restart' fields in ars_status, unfortunately these are
implemented in the middle of the existing definition so this change
is not backwards compatible. The expectation is that shipping
platforms will only ever support the ACPI 6.1 definition.
2/ New status values for ars_start ('busy') and ars_status ('overflow').
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Stable bugfixes:
- Fix nfs_size_to_loff_t
- NFSv4: Fix a dentry leak on alias use
Other bugfixes:
- Don't schedule a layoutreturn if the layout segment can be freed
immediately.
- Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
- rpcrdma_bc_receive_call() should init rq_private_buf.len
- fix stateid handling for the NFS v4.2 operations
- pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
- fix panic in gss_pipe_downcall() in fips mode
- Fix a race between layoutget and pnfs_destroy_layout
- Fix a race between layoutget and bulk recalls"
* tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.x/pnfs: Fix a race between layoutget and bulk recalls
NFSv4.x/pnfs: Fix a race between layoutget and pnfs_destroy_layout
auth_gss: fix panic in gss_pipe_downcall() in fips mode
pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
nfs4: fix stateid handling for the NFS v4.2 operations
NFSv4: Fix a dentry leak on alias use
xprtrdma: rpcrdma_bc_receive_call() should init rq_private_buf.len
pNFS: Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
pNFS: Fix pnfs_mark_matching_lsegs_return()
nfs: fix nfs_size_to_loff_t
|
|
Some DSA drivers may or may not support multiple software bridges on top
of an hardware switch.
It is more convenient for them to access the bridge's net_device for
finer configuration.
Removing the need to craft and access a bitmask also simplifies the
code.
This patch changes the signature of bridge related functions, update DSA
drivers, and removes dsa_slave_br_port_mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduce support for IPHC stateful address compression. It
will offer the context table via one debugfs entry.
This debugfs has and directory for each cid entry for the context table.
Inside each cid directory there exists the following files:
- "active": If the entry is added or deleted. The context table is
original a list implementation, this flag will indicate if the
context is part of list or not.
- "prefix": The ipv6 prefix.
- "prefix_length": The prefix length for the prefix.
- "compression": The compression flag according RFC6775.
This part should be moved into sysfs after some testing time.
Also the debugfs entry contains a "show" file which is a pretty-printout
for the current context table information.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
I got report about that sometimes the WARN_ON occurs there which should
never happen. I came to the conclusion that the mac header is there but
inside the headroom of skb. The skb->len information doesn't contain the
information about the headroom length and skb->len is lesser than two.
We check now if the skb_mac_header pointer is set and the room between
mac header pointer and tail pointer.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add support for LED triggers to the Bluetooth subsystem and add kernel
config symbol BT_LEDS for it.
For now one trigger for indicating "HCI is powered up" is supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
|
|
This fixes "MPWM" -> "WPWM" typo in 3 *ISP_MWPM clock definitions.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Right now, media_device_pci_init and media_device_usb_init does
media_device allocation internaly. That preents its usage when
the media_device struct is embedded on some other structure.
Move memory allocation outside it, to make it more generic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Those ancillary functions could be called even when compiled
without V4L2 support, as warned by ktest build robot:
All errors (new ones prefixed by >>):
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/dvb-usb/dvb-usb.ko] undefined!
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/dvb-usb-v2/dvb_usb_v2.ko] undefined!
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/au0828/au0828.ko] undefined!
Also, there's nothing there that are specific to V4L2. So, move
those ancillary functions to MC core.
No functional changes. Just function rename.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
