| Age | Commit message (Collapse) | Author |
|---|
|
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current implementation of {netdev,napi}_alloc_frag(), it doesn't
have any align guarantee for the returned buffer address, But for some
hardwares they do require the DMA buffer to be aligned correctly,
so we would have to use some workarounds like below if the buffers
allocated by the {netdev,napi}_alloc_frag() are used by these hardwares
for DMA.
buf = napi_alloc_frag(really_needed_size + align);
buf = PTR_ALIGN(buf, align);
These codes seems ugly and would waste a lot of memories if the buffers
are used in a network driver for the TX/RX. We have added the align
support for the page_frag functions, so add the corresponding
{netdev,napi}_frag functions.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current implementation of page_frag_alloc(), it doesn't have
any align guarantee for the returned buffer address. But for some
hardwares they do require the DMA buffer to be aligned correctly,
so we would have to use some workarounds like below if the buffers
allocated by the page_frag_alloc() are used by these hardwares for
DMA.
buf = page_frag_alloc(really_needed_size + align);
buf = PTR_ALIGN(buf, align);
These codes seems ugly and would waste a lot of memories if the buffers
are used in a network driver for the TX/RX. So introduce
page_frag_alloc_align() to make sure that an aligned buffer address is
returned.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The USB "maximum-speed" property can now take the SSP signaling rate
generation and lane count with these new strings:
"super-speed-plus-gen2x2"
"super-speed-plus-gen2x1"
"super-speed-plus-gen1x2"
Introduce usb_get_maximum_ssp_rate() to parse for the corresponding
usb_ssp_rate enum. The original usb_get_maximum_speed() will return
USB_SPEED_SUPER_PLUS if it matches one of these new strings.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f8ed896313d8cd8e2d2b540fc82db92b3ddf8a47.1611106162.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The V4L2 temporary clock helper API, was introduced
in late 2012 and, as mentioned in the documentation,
meant to be replaced by the generic clock API,
once the generic clock framework became available
on all relevant architectures.
The generic clock API is a well-established API (since a few
years now). The last few media capture drivers and sensors
using v4l2-clk have been converted to the generic clock framework.
We can now remove the v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Now that most users of v4l2_async_notifier_add_subdev have been converted,
let's fix the documentation so it's more clear how the v4l2-async API
should be used.
Document functions that drivers should use, and their purpose.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The batman-adv source code was using the year of publication (to net-next)
as "last" year for the copyright statement. The whole source code mentioned
in the MAINTAINERS "BATMAN ADVANCED" section was handled as a single entity
regarding the publishing year.
This avoided having outdated (in sense of year information - not copyright
holder) publishing information inside several files. But since the simple
"update copyright year" commit (without other changes) in the file was not
well received in the upstream kernel, the option to not have a copyright
year (for initial and last publication) in the files are chosen instead.
More detailed information about the years can still be retrieved from the
SCM system.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Most -if not all- use-cases are expected to be covered by one of:
v4l2_async_notifier_add_fwnode_subdev,
v4l2_async_notifier_add_fwnode_remote_subdev or
v4l2_async_notifier_add_i2c_subdev.
We'd like to discourage drivers from using v4l2_async_notifier_add_subdev,
so rename it as __v4l2_async_notifier_add_subdev. This is
typically a good hint for drivers to avoid using the function.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are no users for vpif_display_config.asd_sizes
and vpif_display_config.asd members, which means the v4l2-async
subdevices aren't being defined anywhere.
Remove the v4l2-async, leaving only the synchronous setup.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Change v4l2_async_notifier_add_fwnode_remote_subdev semantics
so it allocates the struct v4l2_async_subdev pointer.
This makes the API consistent: the v4l2-async subdevice addition
functions have now a unified usage model. This model is simpler,
as it makes v4l2-async responsible for the allocation and release
of the subdevice descriptor, and no longer something the driver
has to worry about.
On the user side, the change makes the API simpler for the drivers
to use and less error-prone.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The last user for this type of match was the soc-camera/sh_mobile_csi2
driver, which was removed in v4.9. If the support is ever needed,
it can always be restored.
[Sakari Ailus: Also drop DEVNAME from debug prints recently added.]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Previous patch in series that implements stack devices RX path implements
indirect table rules that match on tunnel VNI. After such rule is created
all tunnel traffic is recirculated to root table. However, recirculated
packet might not match on any rules installed in the table (for example,
when IP traffic follows ARP traffic). In that case packets appear on
representor of tunnel endpoint VF instead being redirected to the VF
itself.
Extend slow table with additional flow group that matches on reg_c0 (source
port value set by indirect tables implemented by previous patch in series)
and reg_c1 (special 0xFFF mark). When creating offloads fdb tables, install
one rule per VF vport to match on recirculated miss packets and redirect
them to appropriate VF vport. Modify indirect tables code to also rewrite
reg_c1 with special 0xFFF mark.
Implementation reuses reg_c1 tunnel id bits. This is safe to do because
recirculated packets are always matched before decapsulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Following patch in series uses reg_c1 in eswitch code. To use reg_c1
helpers in both TC and eswitch code, refactor existing helpers according to
similar use case of reg_c0 and move the functionality into eswitch.h.
Calculate reg mappings length from new defines to ensure that they are
always in sync and only need to be changed in single place.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When tunnel endpoint is on VF, driver still assumes that endpoint is on
uplink and incorrectly configures encap rule offload according to that
assumption. As a result, traffic is sent directly to the uplink and rules
installed on representor of tunnel endpoint VF are ignored.
Implement following changes to allow offloading tx traffic with tunnel
endpoint on VF:
- For tunneling flows perform route lookup on route and out devices pair.
If out device is uplink and route device is VF of same physical port, then
modify packet reg_c_0 metadata register (source port) with the value of VF
vport. Use eswitch vhca_id->vport mapping introduced in one of previous
patches in the series to obtain vport from route netdevice.
- Recirculate encapsulated packets to VF vport in order to apply any flow
rules installed on VF representor that match on encapsulated traffic.
Only enable support for this functionality when all following conditions
are true:
- Hardware advertises capability to preserve reg_c_0 value on packet
recirculation.
- Vport metadata matching is enabled.
- Termination tables are to be used by the flow.
Example TC rules for VF tunnel traffic:
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Needed to provide clocks for cameras.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210205110502.1850669-3-heiko@sntech.de
|
|
Needed by the mipi dphys.
The naming follows the clock names in the manual.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210205110502.1850669-1-heiko@sntech.de
|
|
Michael Kerrisk suggested that, from an API perspective, it is a bad
idea to share the PR_SYS_DISPATCH_ defines between the prctl operation
and the selector variable.
Therefore, define two new constants to be used by SUD's selector variable
and update the corresponding documentation and test cases.
While this changes the API syscall user dispatch has never been part of a
Linux release, it will show up for the first time in 5.11.
Suggested-by: Michael Kerrisk (man-pages) <mtk.manpages@gmail.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210205184321.2062251-1-krisman@collabora.com
|
|
Commit 299155244770 ("entry: Drop usage of TIF flags in the generic syscall
code") introduced a bug on architectures using the generic syscall entry
code, in which processes stopped by PTRACE_SYSCALL do not trap on syscall
return after receiving a TIF_SINGLESTEP.
The reason is that the meaning of TIF_SINGLESTEP flag is overloaded to
cause the trap after a system call is executed, but since the above commit,
the syscall call handler only checks for the SYSCALL_WORK flags on the exit
work.
Split the meaning of TIF_SINGLESTEP such that it only means single-step
mode, and create a new type of SYSCALL_WORK to request a trap immediately
after a syscall in single-step mode. In the current implementation, the
SYSCALL_WORK flag shadows the TIF_SINGLESTEP flag for simplicity.
Update x86 to flip this bit when a tracer enables single stepping.
Fixes: 299155244770 ("entry: Drop usage of TIF flags in the generic syscall code")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kyle Huey <me@kylehuey.com>
Link: https://lore.kernel.org/r/87h7mtc9pr.fsf_-_@collabora.com
|
|
Merge misc fixes from Andrew Morton:
"18 patches.
Subsystems affected by this patch series: mm (hugetlb, compaction,
vmalloc, shmem, memblock, pagecache, kasan, and hugetlb), mailmap,
gcov, ubsan, and MAINTAINERS"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS/.mailmap: use my @kernel.org address
mm: hugetlb: fix missing put_page in gather_surplus_pages()
ubsan: implement __ubsan_handle_alignment_assumption
kasan: make addr_has_metadata() return true for valid addresses
kasan: add explicit preconditions to kasan_report()
mm/filemap: add missing mem_cgroup_uncharge() to __add_to_page_cache_locked()
mailmap: add entries for Manivannan Sadhasivam
mailmap: fix name/email for Viresh Kumar
memblock: do not start bottom-up allocations with kernel_end
mm: thp: fix MADV_REMOVE deadlock on shmem THP
init/gcov: allow CONFIG_CONSTRUCTORS on UML to fix module gcov
mm/vmalloc: separate put pages and flush VM flags
mm, compaction: move high_pfn to the for loop scope
mm: migrate: do not migrate HugeTLB page whose refcount is one
mm: hugetlb: remove VM_BUG_ON_PAGE from page_huge_active
mm: hugetlb: fix a race between isolating and freeing page
mm: hugetlb: fix a race between freeing and dissolving the page
mm: hugetlbfs: fix cannot migrate the fallocated HugeTLB page
|
|
Since commit a85a6c86c25b ("driver core: platform: Clarify that IRQ 0
is invalid"), having a linux-irq with number 0 will trigger a WARN()
when calling platform_get_irq*() to retrieve that linux-irq.
Since [devm_]irq_alloc_desc allocs a single irq and since irq 0 is not used
on some systems, it can return 0, triggering that WARN(). This happens
e.g. on Intel Bay Trail and Cherry Trail devices using the LPE audio engine
for HDMI audio:
0 is an invalid IRQ number
WARNING: CPU: 3 PID: 472 at drivers/base/platform.c:238 platform_get_irq_optional+0x108/0x180
Modules linked in: snd_hdmi_lpe_audio(+) ...
Call Trace:
platform_get_irq+0x17/0x30
hdmi_lpe_audio_probe+0x4a/0x6c0 [snd_hdmi_lpe_audio]
---[ end trace ceece38854223a0b ]---
Change the 'from' parameter passed to __[devm_]irq_alloc_descs() by the
[devm_]irq_alloc_desc macros from 0 to 1, so that these macros will no
longer return 0.
Fixes: a85a6c86c25b ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201221185647.226146-1-hdegoede@redhat.com
|
|
Patch series "kasan: Fix metadata detection for KASAN_HW_TAGS", v5.
With the introduction of KASAN_HW_TAGS, kasan_report() currently assumes
that every location in memory has valid metadata associated. This is
due to the fact that addr_has_metadata() returns always true.
As a consequence of this, an invalid address (e.g. NULL pointer
address) passed to kasan_report() when KASAN_HW_TAGS is enabled, leads
to a kernel panic.
Example below, based on arm64:
BUG: KASAN: invalid-access in 0x0
Read at addr 0000000000000000 by task swapper/0/1
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
...
Call trace:
mte_get_mem_tag+0x24/0x40
kasan_report+0x1a4/0x410
alsa_sound_last_init+0x8c/0xa4
do_one_initcall+0x50/0x1b0
kernel_init_freeable+0x1d4/0x23c
kernel_init+0x14/0x118
ret_from_fork+0x10/0x34
Code: d65f03c0 9000f021 f9428021 b6cfff61 (d9600000)
---[ end trace 377c8bb45bdd3a1a ]---
hrtimer: interrupt took 48694256 ns
note: swapper/0[1] exited with preempt_count 1
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
SMP: stopping secondary CPUs
Kernel Offset: 0x35abaf140000 from 0xffff800010000000
PHYS_OFFSET: 0x40000000
CPU features: 0x0a7e0152,61c0a030
Memory Limit: none
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
This series fixes the behavior of addr_has_metadata() that now returns
true only when the address is valid.
This patch (of 2):
With the introduction of KASAN_HW_TAGS, kasan_report() accesses the
metadata only when addr_has_metadata() succeeds.
Add a comment to make sure that the preconditions to the function are
explicitly clarified.
Link: https://lkml.kernel.org/r/20210126134409.47894-1-vincenzo.frascino@arm.com
Link: https://lkml.kernel.org/r/20210126134409.47894-2-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: "Paul E . McKenney" <paulmck@kernel.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When VM_MAP_PUT_PAGES was added, it was defined with the same value as
VM_FLUSH_RESET_PERMS. This doesn't seem like it will cause any big
functional problems other than some excess flushing for VM_MAP_PUT_PAGES
allocations.
Redefine VM_MAP_PUT_PAGES to have its own value. Also, rearrange things
so flags are less likely to be missed in the future.
Link: https://lkml.kernel.org/r/20210122233706.9304-1-rick.p.edgecombe@intel.com
Fixes: b944afc9d64d ("mm: add a VM_MAP_PUT_PAGES flag for vmap")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Axtens <dja@axtens.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a new hugetlb page is allocated during fallocate it will not be
marked as active (set_page_huge_active) which will result in a later
isolate_huge_page failure when the page migration code would like to
move that page. Such a failure would be unexpected and wrong.
Only export set_page_huge_active, just leave clear_page_huge_active as
static. Because there are no external users.
Link: https://lkml.kernel.org/r/20210115124942.46403-3-songmuchun@bytedance.com
Fixes: 70c3547e36f5 (hugetlbfs: add hugetlbfs_fallocate())
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Fix a possible NULL-ptr dereference in dev_iommu_priv_get() which is
too easy to accidentially trigger from IOMMU drivers.
In the current case the AMD IOMMU driver triggered it on some machines
in the IO-page-fault path, so fix it once and for all"
* tag 'iommu-fixes-v5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Check dev->iommu in dev_iommu_priv_get() before dereferencing it
|
|
Pull drm fixes from Dave Airlie:
"Fixes for rc7, bit bigger than I'd like at this stage, but most of the
i915 stuff and some amdgpu is destined for staging and I'd rather not
hold it up, the i915 changes also pulled in a few precusor code
movement patches to make things cleaner, but nothing seems that
horrible, and I've checked over all of it.
Otherwise there is a nouveau dma-api warning regression, and a ttm
page allocation warning fix, and some fixes for a bridge chip,
ttm:
- fix huge page warning regression
i915:
- Skip vswing programming for TBT
- Power up combo PHY lanes for HDMI
- Fix double YUV range correction on HDR planes
- Fix the MST PBN divider calculation
- Fix LTTPR vswing/pre-emp setting in non-transparent mode
- Move the breadcrumb to the signaler if completed upon cancel
- Close race between enable_breadcrumbs and cancel_breadcrumbs
- Drop lru bumping on display unpinning
amdgpu:
- Fix retry in gem create
- Vangogh fixes
- Fix for display from shared buffers
- Various display fixes
amdkfd:
- Fix regression in buffer free
nouveau:
- fix DMA API warning regression
drm/bridge/lontium-lt9611uxc:
- EDID fixes
- Don't handle hotplug events in IRQ handler"
* tag 'drm-fixes-2021-02-05-1' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/nouveau: fix dma syncing warning with debugging on.
drm/amd/display: Decrement refcount of dc_sink before reassignment
drm/amd/display: Free atomic state after drm_atomic_commit
drm/amd/display: Fix dc_sink kref count in emulated_link_detect
drm/amd/display: Release DSC before acquiring
drm/amd/display: Revert "Fix EDID parsing after resume from suspend"
drm/amd/display: Add more Clock Sources to DCN2.1
drm/amd/display: reuse current context instead of recreating one
drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVAL
drm/amdgpu: enable freesync for A+A configs
drm/amd/pm: fill in the data member of v2 gpu metrics table for vangogh
drm/amdgpu/gfx10: update CGTS_TCC_DISABLE and CGTS_USER_TCC_DISABLE register offsets for VGH
drm/amdkfd: fix null pointer panic while free buffer in kfd
drm/amdgpu: fix the issue that retry constantly once the buffer is oversize
drm/i915/dp: Fix LTTPR vswing/pre-emp setting in non-transparent mode
drm/i915/dp: Move intel_dp_set_signal_levels() to intel_dp_link_training.c
drm/i915: Fix the MST PBN divider calculation
drm/dp/mst: Export drm_dp_get_vc_payload_bw()
drm/i915/gem: Drop lru bumping on display unpinning
drm/i915/gt: Close race between enable_breadcrumbs and cancel_breadcrumbs
...
|
|
The commit e7bbb7acabf4 ("dmaengine: add peripheral configuration")
adds peripheral configuration for dma_slave_config.
This configuration is useful for some audio peripherals, for
example, the peripheral supports multi fifos, we can
let the DMA know which fifos are selected. So also add
this configuration for snd_dmaengine_dai_dma_data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1612509985-11063-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently mlx5 driver caches port GID table length for 2 ports. It is
also cached by IB core as port immutable data.
When mlx5 representor ports are present, which are usually more than 2,
invalid access to port_caps array can happen while validating the GID
table length which is only for 2 ports.
To avoid this, take help of the IB cores port immutable data by exposing
an API to read the port immutable fields.
Remove mlx5 driver's internal cache, thereby reduce code and data.
Link: https://lore.kernel.org/r/20210203130133.4057329-5-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
mlx5_port_caps are RDMA specific capabilities. These are not used by the
mlx5_core_device at all. Move them to mlx5_ib_dev where it is used and
reduce the scope of it to multiple drivers.
Link: https://lore.kernel.org/r/20210203130133.4057329-2-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
|
|
The Global Block Unlock command has different names depending
on the manufacturer, but always the same command value: 0x98.
Macronix's MX25U12835F names it Gang Block Unlock, Winbond's
W25Q128FV names it Global Block Unlock and Microchip's
SST26VF064B names it Global Block Protection Unlock.
Used in the Individual Block Protection mode, which is mutually
exclusive with the Block Protection mode (BP0-3).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210121110546.382633-1-tudor.ambarus@microchip.com
|
|
An erroneous or malicious host could send multiple rescind messages for
a same channel. In vmbus_onoffer_rescind(), the guest maps the channel
ID to obtain a pointer to the channel object and it eventually releases
such object and associated data. The host could time rescind messages
and lead to an use-after-free. Add a new flag to the channel structure
to make sure that only one instance of vmbus_onoffer_rescind() can get
the reference to the channel object.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20201209070827.29335-6-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest in the host-to-guest ring buffer. Ensure that
invalid values cannot cause indexing off the end of the icversion_data
array in vmbus_prep_negotiate_resp().
Signed-off-by: Andres Beltran <lkmlabelt@gmail.com>
Co-developed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20201109100704.9152-1-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Pointers to ring-buffer packets sent by Hyper-V are used within the
guest VM. Hyper-V can send packets with erroneous values or modify
packet fields after they are processed by the guest. To defend
against these scenarios, return a copy of the incoming VMBus packet
after validating its length and offset fields in hv_pkt_iter_first().
In this way, the packet can no longer be modified by the host.
Signed-off-by: Andres Beltran <lkmlabelt@gmail.com>
Co-developed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20201208045311.10244-1-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
At the moment the function device_del() is calling
device_remove_properties() unconditionally. That will result into the
reference count of the software node attached to the device being
decremented, and in most cases it will hit 0 at that point. So in
practice device_del() will unregister the software node attached to
the device, even if that was not the intention of the caller. Right
now software nodes can not be reused or shared because of that.
So device_del() can not unregister the software nodes unconditionally
like that. Unfortunately some of the users of device_add_properties()
are now relying on this behaviour. Because of that, and also in
general, we do need a function that can offer similar behaviour where
the lifetime of the software node is bound to the lifetime of the
device. But it just has to be a separate function so the behaviour is
optional. We can not remove the device_remove_properties() call from
device_del() before we have that new function, and before we have
replaced device_add_properties() calls with it in all the places that
require that behaviour.
This adds function device_create_managed_software_node() that can be
used for exactly that purpose. Software nodes created with it are
declared "managed", and separate handling for those nodes is added to
the software node code. The reference count of the "managed" nodes is
decremented when the device they are attached to is removed. This will
not affect the other nodes that are not declared "managed".
The function device_create_managed_software_node() has also one
additional feature that device_add_properties() does not have. It
allows the software nodes created with it to be part of a node
hierarchy by taking also an optional parent node as parameter.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210204141711.53775-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'tag-ib-usb-typec-chrome-platform-cros-ec-typec-clear-pd-discovery-events-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux into usb-next
Benson writes:
clear-pd-discovery-events
This pair of patches fixes an issue where cros_ec_typec creates stale
cable nodes on detach because of uncleared pd discovery status events.
* tag 'tag-ib-usb-typec-chrome-platform-cros-ec-typec-clear-pd-discovery-events-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_typec: Clear Type C disc events
platform/chrome: cros_ec: Import Type C control command
|
|
When iteratively computing a checksum with csum_block_add, track the
offset "pos" to correctly rotate in csum_block_add when offset is odd.
The open coded implementation of skb_copy_and_csum_datagram did this.
With the switch to __skb_datagram_iter calling csum_and_copy_to_iter,
pos was reinitialized to 0 on each call.
Bring back the pos by passing it along with the csum to the callback.
Changes v1->v2
- pass csum value, instead of csump pointer (Alexander Duyck)
Link: https://lore.kernel.org/netdev/20210128152353.GB27281@optiplex/
Fixes: 950fcaecd5cc ("datagram: consolidate datagram copy to iter helpers")
Reported-by: Oliver Graute <oliver.graute@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210203192952.1849843-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following compilation warnings:
net/netfilter/ipvs/ip_vs_proto_tcp.c:147:1: warning: no previous prototype for 'tcp_snat_handler' [-Wmissing-prototypes]
147 | tcp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
| ^~~~~~~~~~~~~~~~
net/netfilter/ipvs/ip_vs_proto_udp.c:136:1: warning: no previous prototype for 'udp_snat_handler' [-Wmissing-prototypes]
136 | udp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
| ^~~~~~~~~~~~~~~~
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fir the following compilation warnings:
1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
| ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
| ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following compilation warning:
net/ipv6/udp.c:1031:30: warning: no previous prototype for 'udp_v6_early_demux' [-Wmissing-prototypes]
1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~~~
net/ipv6/udp.c:1072:29: warning: no previous prototype for 'udpv6_rcv' [-Wmissing-prototypes]
1072 | INDIRECT_CALLABLE_SCOPE int udpv6_rcv(struct sk_buff *skb)
| ^~~~~~~~~
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The W=1 compilation of allmodconfig generates the following warning:
net/ipv6/icmp.c:448:6: warning: no previous prototype for 'icmp6_send' [-Wmissing-prototypes]
448 | void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
| ^~~~~~~~~~
Fix it by providing function declaration for builds with ipv6 as a module.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().
This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().
v1->v2:
- add udp_encap_disable() and export it.
v2->v3:
- add the change for rxrpc and bareudp into one patch, as Alex
suggested.
v3->v4:
- move rxrpc part to another patch.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A bunch of drivers test the page before reusing/recycling for two
common conditions:
- if a page was allocated under memory pressure (pfmemalloc page);
- if a page was allocated at a distant memory node (to exclude
slowdowns).
Introduce a new common inline for doing this, with likely() already
folded inside to make driver code a bit simpler.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function doesn't write anything to the page struct itself,
so this argument can be const.
Misc: align second argument to the brace while at it.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function only tests for page->index, so its argument should be
const.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a static function is annotated with INDIRECT_CALLABLE_SCOPE and
CONFIG_RETPOLINE is set, the static keyword is removed. Sometimes the
function needs to be exported but EXPORT_SYMBOL can't be used because if
CONFIG_RETPOLINE is not set, we will attempt to export a static symbol.
This patch introduces a new indirect call wrapper:
EXPORT_INDIRECT_CALLABLE. This basically does EXPORT_SYMBOL when
CONFIG_RETPOLINE is set, but does nothing when it's not.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Often userspace won't request the extack information, or they don't log it
because of log level or so, and even when they do, sometimes it's not
enough to know exactly what caused the error.
Netlink extack is the standard way of reporting erros with descriptive
error messages. With a trace point on it, we then can know exactly where
the error happened, regardless of userspace app. Also, we can even see if
the err msg was overwritten.
The wrapper do_trace_netlink_extack() is because trace points shouldn't be
called from .h files, as trace points are not that small, and the function
call to do_trace_netlink_extack() on the macros is not protected by
tracepoint_enabled() because the macros are called from modules, and this
would require exporting some trace structs. As this is error path, it's
better to export just the wrapper instead.
v2: removed leftover tracepoint declaration
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/4546b63e67b2989789d146498b13cc09e1fdc543.1612403190.git.marcelo.leitner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.12
1. Decouple Mediatek DRM sub driver
2. Share mtk mutex driver for both DRM and MDP
3. Add support for SoC MT8183
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204151750.7550-1-chunkuang.hu@kernel.org
|
