| Age | Commit message (Collapse) | Author |
|---|
|
Merge cpufreq changes for 6.9-rc1:
- Enable preferred core support in the amd-pstate cpufreq driver (Meng
Li).
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li).
- Change default transition delay in cpufreq to 2ms (Qais Yousef).
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby).
- Allow intel_pstate to assign model-specific values to strings used in
the EPP sysfs interface and make it do so on Meteor Lake (Srinivas
Pandruvada).
- Remove references to 10ms minimum sampling rate from comments in the
cpufreq code (Pierre Gondois).
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar).
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef).
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar).
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois).
* pm-cpufreq: (28 commits)
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
cpufreq: intel_pstate: Allow model specific EPPs
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: intel_pstate: remove cpudata::prev_cummulative_iowait
cpufreq: Change default transition delay to 2ms
cpufreq: amd-pstate: Fix min_perf assignment in amd_pstate_adjust_perf()
Documentation: PM: amd-pstate: Fix section title underline
Documentation: introduce amd-pstate preferrd core mode kernel command line options
Documentation: amd-pstate: introduce amd-pstate preferred core
cpufreq: amd-pstate: Update amd-pstate preferred core ranking dynamically
ACPI: cpufreq: Add highest perf change notification
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.9 from Viresh Kumar:
"- General enhancements / cleanups to cpufreq drivers (tianyu2, Nícolas
F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- scmi: get transition delay from firmware (Pierre Gondois)."
* tag 'cpufreq-arm-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: mediatek-hw: Don't error out if supply is not found
Documentation: power: Use kcalloc() instead of kzalloc()
cpufreq: mediatek-hw: Wait for CPU supplies before probing
cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
cpufreq: imx6: use regmap to read ocotp register
|
|
KVM x86 misc changes for 6.9:
- Explicitly initialize a variety of on-stack variables in the emulator that
triggered KMSAN false positives (though in fairness in KMSAN, it's comically
difficult to see that the uninitialized memory is never truly consumed).
- Fix the deubgregs ABI for 32-bit KVM, and clean up code related to reading
DR6 and DR7.
- Rework the "force immediate exit" code so that vendor code ultimately
decides how and when to force the exit. This allows VMX to further optimize
handling preemption timer exits, and allows SVM to avoid sending a duplicate
IPI (SVM also has a need to force an exit).
- Fix a long-standing bug where kvm_has_noapic_vcpu could be left elevated if
vCPU creation ultimately failed, and add WARN to guard against similar bugs.
- Provide a dedicated arch hook for checking if a different vCPU was in-kernel
(for directed yield), and simplify the logic for checking if the currently
loaded vCPU is in-kernel.
- Misc cleanups and fixes.
|
|
The kernel CONFIG_UNWINDER_ORC option enables the ORC unwinder, which is
similar in concept to a DWARF unwinder. The difference is that the format
of the ORC data is much simpler than DWARF, which in turn allows the ORC
unwinder to be much simpler and faster.
The ORC data consists of unwind tables which are generated by objtool.
After analyzing all the code paths of a .o file, it determines information
about the stack state at each instruction address in the file and outputs
that information to the .orc_unwind and .orc_unwind_ip sections.
The per-object ORC sections are combined at link time and are sorted and
post-processed at boot time. The unwinder uses the resulting data to
correlate instruction addresses with their stack states at run time.
Most of the logic are similar with x86, in order to get ra info before ra
is saved into stack, add ra_reg and ra_offset into orc_entry. At the same
time, modify some arch-specific code to silence the objtool warnings.
Co-developed-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Co-developed-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
KVM async page fault changes for 6.9:
- Always flush the async page fault workqueue when a work item is being
removed, especially during vCPU destruction, to ensure that there are no
workers running in KVM code when all references to KVM-the-module are gone,
i.e. to prevent a use-after-free if kvm.ko is unloaded.
- Grab a reference to the VM's mm_struct in the async #PF worker itself instead
of gifting the worker a reference, e.g. so that there's no need to remember
to *conditionally* clean up after the worker.
|
|
Merge changes related to the runtime power management of devices for
6.9-rc1:
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus).
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat).
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin).
* pm-runtime:
Documentation: PM: Fix runtime_pm.rst markdown syntax
PM: runtime: add tracepoint for runtime_status changes
PM: runtime: Add pm_runtime_put_autosuspend() replacement
PM: runtime: Simplify pm_runtime_get_if_active() usage
|
|
Merge changes related to system-wide power management for 6.9-rc1:
- Fix and clean up system suspend statistics collection (Rafael
Wysocki).
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki).
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V).
- Fix PCI hibernation support description (Yiwei Lin).
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy).
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah).
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li).
* pm-sleep: (21 commits)
PM: sleep: wakeirq: fix wake irq warning in system suspend
PM: suspend: Set mem_sleep_current during kernel command line setup
PM: hibernate: Don't ignore return from set_memory_ro()
PM: hibernate: Support to select compression algorithm
Documentation: PM: Fix PCI hibernation support description
PM: hibernate: Add support for LZ4 compression for hibernation
PM: hibernate: Move to crypto APIs for LZO compression
PM: hibernate: Rename lzo* to make it generic
PM: sleep: Call dpm_async_fn() directly in each suspend phase
PM: sleep: Move devices to new lists earlier in each suspend phase
PM: sleep: Move some assignments from under a lock
PM: sleep: stats: Log errors right after running suspend callbacks
PM: sleep: stats: Use locking in dpm_save_failed_dev()
PM: sleep: stats: Call dpm_save_failed_step() at most once per phase
PM: sleep: stats: Define suspend_stats next to the code using it
PM: sleep: stats: Use unsigned int for success and failure counters
PM: sleep: stats: Use an array of step failure counters
PM: sleep: stats: Use array of suspend step names
PM: sleep: Relocate two device PM core functions
PM: sleep: Simplify dpm_suspended_list walk in dpm_resume()
...
|
|
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for 6.9
- Infrastructure for building KVM's trap configuration based on the
architectural features (or lack thereof) advertised in the VM's ID
registers
- Support for mapping vfio-pci BARs as Normal-NC (vaguely similar to
x86's WC) at stage-2, improving the performance of interacting with
assigned devices that can tolerate it
- Conversion of KVM's representation of LPIs to an xarray, utilized to
address serialization some of the serialization on the LPI injection
path
- Support for _architectural_ VHE-only systems, advertised through the
absence of FEAT_E2H0 in the CPU's ID register
- Miscellaneous cleanups, fixes, and spelling corrections to KVM and
selftests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson into HEAD
LoongArch KVM changes for v6.9
* Set reserved bits as zero in CPUCFG.
* Start SW timer only when vcpu is blocking.
* Do not restart SW timer when it is expired.
* Remove unnecessary CSR register saving during enter guest.
|
|
Merge x86-specific ACPI changes, an ACPI backlight driver change, ACPI
APEI change and miscellaneous ACPI-related changes for 6.9-rc1:
- Add DELL0501 handling to acpi_quirk_skip_serdev_enumeration() and
make that function generic (Hans de Goede).
- Make the ACPI backlight code handle fetching EDID that is longer than
256 bytes (Mario Limonciello).
- Skip initialization of GHES_ASSIST structures for Machine Check
Architecture in APEI (Avadhut Naik).
- Convert several plaform drivers in the ACPI subsystem to using a
remove callback that returns void (Uwe Kleine-König).
- Drop the long-deprecated custom_method debugfs interface that is
problematic from the security standpoint (Rafael Wysocki).
- Use %pe in a couple of places in the ACPI code for easier error
decoding (Onkarnath).
* acpi-x86:
ACPI: x86: Add DELL0501 handling to acpi_quirk_skip_serdev_enumeration()
ACPI: x86: Move acpi_quirk_skip_serdev_enumeration() out of CONFIG_X86_ANDROID_TABLETS
* acpi-video:
ACPI: video: Handle fetching EDID that is longer than 256 bytes
* acpi-apei:
ACPI: APEI: Skip initialization of GHES_ASSIST structures for Machine Check Architecture
ACPI: APEI: GHES: Convert to platform remove callback returning void
* acpi-misc:
ACPI: pfr_update: Convert to platform remove callback returning void
ACPI: pfr_telemetry: Convert to platform remove callback returning void
ACPI: fan: Convert to platform remove callback returning void
ACPI: GED: Convert to platform remove callback returning void
ACPI: DPTF: Convert to platform remove callback returning void
ACPI: AGDI: Convert to platform remove callback returning void
ACPI: TAD: Convert to platform remove callback returning void
ACPI: Drop the custom_method debugfs interface
ACPI: use %pe for better readability of errors while printing
|
|
'acpi-thermal'
Merge ACPI tables parsing change, ACPI processor driver change, ACPI
device properties handling changes and an ACPI thermal code change for
6.9-rc1:
- Make the NFIT parsing code use acpi_evaluate_dsm_typed() (Andy
Shevchenko).
- Fix a memory leak in acpi_processor_power_exit() (Armin Wolf).
- Make it possible to quirk the CSI-2 and MIPI DisCo for Imaging
properties parsing and add a quirk for Dell XPS 9315 (Sakari Ailus).
- Prevent false-positive static checker warnings from triggering by
intializing some variables in the ACPI thermal code to zero (Colin
Ian King).
* acpi-tables:
ACPI: NFIT: Switch to use acpi_evaluate_dsm_typed()
* acpi-processor:
ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit()
* acpi-property:
ACPI: property: Polish ignoring bad data nodes
ACPI: property: Ignore bad graph port nodes on Dell XPS 9315
ACPI: utils: Make acpi_handle_path() not static
* acpi-thermal:
ACPI: thermal_lib: Initialize temp_decik to zero
|
|
Merge ACPI device enumeration and bus type changes, ACPI power
management changes and ACPI IRQ override handling quirks for 6.9-rc1:
- Rearrange Device Check and Bus Check notification handling in the
ACPI device hotplug code to make it get the "enabled" _STA bit into
account (Rafael Wysocki).
- Modify acpi_processor_add() to skip processors with the "enabled"
_STA bit clear, as per the specification (Rafael Wysocki).
- Stop failing Device Check notification handling without a valid
reason (Rafael Wysocki).
- Defer enumeration of devices that depend on a device with an ACPI
device ID equalt to INTC10CF to address probe ordering issues on
some platforms (Wentong Wu).
- Constify acpi_bus_type (Ricardo Marliere).
- Make the ACPI-specific suspend-to-idle code take the Low-Power S0
Idle MSFT UUID into account on non-AMD systems (Rafael Wysocki).
- Add ACPI IRQ override quirks for some new platforms (Sergey
Kalinichev, Maxim Kudinov, Alexey Froloff, Sviatoslav Harasymchuk,
Nicolas Haye).
* acpi-scan:
ACPI: scan: Consolidate Device Check and Bus Check notification handling
ACPI: scan: Rework Device Check and Bus Check notification handling
ACPI: scan: Make acpi_processor_add() check the device enabled bit
ACPI: scan: Relocate acpi_bus_trim_one()
ACPI: scan: Fix device check notification handling
ACPI: scan: Defer enumeration of devices with a _DEP pointing to IVSC device
* acpi-bus:
ACPI: bus: make acpi_bus_type const
* acpi-pm:
ACPI: PM: s2idle: Enable Low-Power S0 Idle MSFT UUID for non-AMD systems
* acpi-resource:
ACPI: resource: Use IRQ override on Maibenben X565
ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
ACPI: resource: Do IRQ override on Lunnen Ground laptops
ACPI: resource: Add IRQ override quirk for ASUS ExpertBook B2502FBA
ACPI: resource: Skip IRQ override on ASUS ExpertBook B1502CVA
|
|
These helpers scatters or gathers a bitmap with the help of the mask
position bits parameter.
bitmap_scatter() does the following:
src: 0000000001011010
||||||
+------+|||||
| +----+||||
| |+----+|||
| || +-+||
| || | ||
mask: ...v..vv...v..vv
...0..11...0..10
dst: 0000001100000010
and bitmap_gather() performs this one:
mask: ...v..vv...v..vv
src: 0000001100000010
^ ^^ ^ 0
| || | 10
| || > 010
| |+--> 1010
| +--> 11010
+----> 011010
dst: 0000000000011010
bitmap_gather() can the seen as the reverse bitmap_scatter() operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/lkml/20230926052007.3917389-3-andriy.shevchenko@linux.intel.com/
Co-developed-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ethtool: ice: Support for RSS settings to GTP
Takeru Hayasaka enables RSS functionality for GTP packets on ice driver
with ethtool.
A user can include TEID and make RSS work for GTP-U over IPv4 by doing the
following:`ethtool -N ens3 rx-flow-hash gtpu4 sde`
In addition to gtpu(4|6), we now support gtpc(4|6),gtpc(4|6)t,gtpu(4|6)e,
gtpu(4|6)u, and gtpu(4|6)d.
gtpc(4|6): Used for GTP-C in IPv4 and IPv6, where the GTP header format does
not include a TEID.
gtpc(4|6)t: Used for GTP-C in IPv4 and IPv6, with a GTP header format that
includes a TEID.
gtpu(4|6): Used for GTP-U in both IPv4 and IPv6 scenarios.
gtpu(4|6)e: Used for GTP-U with extended headers in both IPv4 and IPv6.
gtpu(4|6)u: Used when the PSC (PDU session container) in the GTP-U extended
header includes Uplink, applicable to both IPv4 and IPv6.
gtpu(4|6)d: Used when the PSC in the GTP-U extended header includes Downlink,
for both IPv4 and IPv6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prep for 6.9 merge.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the declaration of functions defined in the OPP core to pm_opp.h.
These were added to cpufreq.h as it was the only user of the APIs, but
that was a mistake perhaps. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Let's extend the dev_pm_opp_data with a turbo variable, to allow users to
specify if it's a boost frequency for a dynamically added OPP.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add config_scsi_dev vops comment.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240301034610.24928-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the input_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240305-class_cleanup-input-v1-1-0c3d950c25db@marliere.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Introduce PF_MEMALLOC_* equivalents of some GFP_ flags:
PF_MEMALLOC_NORECLAIM -> GFP_NOWAIT
PF_MEMALLOC_NOWARN -> __GFP_NOWARN
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: linux-mm@kvack.org
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Our proliferation of memalloc_*_{save,restore} APIs is getting a bit
silly, this adds a generic version and converts the existing
save/restore functions to wrappers.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: linux-mm@kvack.org
Acked-by: Vlastimil Babka <vbabka@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Do not allow large strings (> 4096) as single write to trace_marker
The size of a string written into trace_marker was determined by the
size of the sub-buffer in the ring buffer. That size is dependent on
the PAGE_SIZE of the architecture as it can be mapped into user
space. But on PowerPC, where PAGE_SIZE is 64K, that made the limit of
the string of writing into trace_marker 64K.
One of the selftests looks at the size of the ring buffer sub-buffers
and writes that plus more into the trace_marker. The write will take
what it can and report back what it consumed so that the user space
application (like echo) will write the rest of the string. The string
is stored in the ring buffer and can be read via the "trace" or
"trace_pipe" files.
The reading of the ring buffer uses vsnprintf(), which uses a
precision "%.*s" to make sure it only reads what is stored in the
buffer, as a bug could cause the string to be non terminated.
With the combination of the precision change and the PAGE_SIZE of 64K
allowing huge strings to be added into the ring buffer, plus the test
that would actually stress that limit, a bug was reported that the
precision used was too big for "%.*s" as the string was close to 64K
in size and the max precision of vsnprintf is 32K.
Linus suggested not to have that precision as it could hide a bug if
the string was again stored without a nul byte.
Another issue that was brought up is that the trace_seq buffer is
also based on PAGE_SIZE even though it is not tied to the
architecture limit like the ring buffer sub-buffer is. Having it be
64K * 2 is simply just too big and wasting memory on systems with 64K
page sizes. It is now hardcoded to 8K which is what all other
architectures with 4K PAGE_SIZE has.
Finally, the write to trace_marker is now limited to 4K as there is
no reason to write larger strings into trace_marker.
- ring_buffer_wait() should not loop.
The ring_buffer_wait() does not have the full context (yet) on if it
should loop or not. Just exit the loop as soon as its woken up and
let the callers decide to loop or not (they already do, so it's a bit
redundant).
- Fix shortest_full field to be the smallest amount in the ring buffer
that a waiter is waiting for. The "shortest_full" field is updated
when a new waiter comes in and wants to wait for a smaller amount of
data in the ring buffer than other waiters. But after all waiters are
woken up, it's not reset, so if another waiter comes in wanting to
wait for more data, it will be woken up when the ring buffer has a
smaller amount from what the previous waiters were waiting for.
- The wake up all waiters on close is incorrectly called frome
.release() and not from .flush() so it will never wake up any waiters
as the .release() will not get called until all .read() calls are
finished. And the wakeup is for the waiters in those .read() calls.
* tag 'trace-ring-buffer-v6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Use .flush() call to wake up readers
ring-buffer: Fix resetting of shortest_full
ring-buffer: Fix waking up ring buffer readers
tracing: Limit trace_marker writes to just 4K
tracing: Limit trace_seq size to just 8K and not depend on architecture PAGE_SIZE
tracing: Remove precision vsnprintf() check from print event
|
|
Pull kvm fixes from Paolo Bonzini:
"KVM GUEST_MEMFD fixes for 6.8:
- Make KVM_MEM_GUEST_MEMFD mutually exclusive with KVM_MEM_READONLY
to avoid creating an inconsistent ABI (KVM_MEM_GUEST_MEMFD is not
writable from userspace, so there would be no way to write to a
read-only guest_memfd).
- Update documentation for KVM_SW_PROTECTED_VM to make it abundantly
clear that such VMs are purely for development and testing.
- Limit KVM_SW_PROTECTED_VM guests to the TDP MMU, as the long term
plan is to support confidential VMs with deterministic private
memory (SNP and TDX) only in the TDP MMU.
- Fix a bug in a GUEST_MEMFD dirty logging test that caused false
passes.
x86 fixes:
- Fix missing marking of a guest page as dirty when emulating an
atomic access.
- Check for mmu_notifier invalidation events before faulting in the
pfn, and before acquiring mmu_lock, to avoid unnecessary work and
lock contention with preemptible kernels (including
CONFIG_PREEMPT_DYNAMIC in non-preemptible mode).
- Disable AMD DebugSwap by default, it breaks VMSA signing and will
be re-enabled with a better VM creation API in 6.10.
- Do the cache flush of converted pages in svm_register_enc_region()
before dropping kvm->lock, to avoid a race with unregistering of
the same region and the consequent use-after-free issue"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
SEV: disable SEV-ES DebugSwap by default
KVM: x86/mmu: Retry fault before acquiring mmu_lock if mapping is changing
KVM: SVM: Flush pages under kvm->lock to fix UAF in svm_register_enc_region()
KVM: selftests: Add a testcase to verify GUEST_MEMFD and READONLY are exclusive
KVM: selftests: Create GUEST_MEMFD for relevant invalid flags testcases
KVM: x86/mmu: Restrict KVM_SW_PROTECTED_VM to the TDP MMU
KVM: x86: Update KVM_SW_PROTECTED_VM docs to make it clear they're a WIP
KVM: Make KVM_MEM_GUEST_MEMFD mutually exclusive with KVM_MEM_READONLY
KVM: x86: Mark target gfn of emulated atomic instruction as dirty
|
|
https://github.com/kvm-x86/linux into HEAD
KVM GUEST_MEMFD fixes for 6.8:
- Make KVM_MEM_GUEST_MEMFD mutually exclusive with KVM_MEM_READONLY to
avoid creating ABI that KVM can't sanely support.
- Update documentation for KVM_SW_PROTECTED_VM to make it abundantly
clear that such VMs are purely a development and testing vehicle, and
come with zero guarantees.
- Limit KVM_SW_PROTECTED_VM guests to the TDP MMU, as the long term plan
is to support confidential VMs with deterministic private memory (SNP
and TDX) only in the TDP MMU.
- Fix a bug in a GUEST_MEMFD negative test that resulted in false passes
when verifying that KVM_MEM_GUEST_MEMFD memslots can't be dirty logged.
|
|
In production we have been hitting the following warning consistently
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 17 PID: 1800359 at lib/refcount.c:28 refcount_warn_saturate+0x9c/0xe0
Workqueue: nfsiod nfs_direct_write_schedule_work [nfs]
RIP: 0010:refcount_warn_saturate+0x9c/0xe0
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0x9f/0x130
? refcount_warn_saturate+0x9c/0xe0
? report_bug+0xcc/0x150
? handle_bug+0x3d/0x70
? exc_invalid_op+0x16/0x40
? asm_exc_invalid_op+0x16/0x20
? refcount_warn_saturate+0x9c/0xe0
nfs_direct_write_schedule_work+0x237/0x250 [nfs]
process_one_work+0x12f/0x4a0
worker_thread+0x14e/0x3b0
? ZSTD_getCParams_internal+0x220/0x220
kthread+0xdc/0x120
? __btf_name_valid+0xa0/0xa0
ret_from_fork+0x1f/0x30
This is because we're completing the nfs_direct_request twice in a row.
The source of this is when we have our commit requests to submit, we
process them and send them off, and then in the completion path for the
commit requests we have
if (nfs_commit_end(cinfo.mds))
nfs_direct_write_complete(dreq);
However since we're submitting asynchronous requests we sometimes have
one that completes before we submit the next one, so we end up calling
complete on the nfs_direct_request twice.
The only other place we use nfs_generic_commit_list() is in
__nfs_commit_inode, which wraps this call in a
nfs_commit_begin();
nfs_commit_end();
Which is a common pattern for this style of completion handling, one
that is also repeated in the direct code with get_dreq()/put_dreq()
calls around where we process events as well as in the completion paths.
Fix this by using the same pattern for the commit requests.
Before with my 200 node rocksdb stress running this warning would pop
every 10ish minutes. With my patch the stress test has been running for
several hours without popping.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
We want to be able to have our rpc stats handled in a per network
namespace manner, so add an option to rpc_create_args to specify a
different rpc_stats struct instead of using the one on the rpc_program.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Nothing uses this, and thank goodness, as the syntax looks horrid.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Add a tracepoint to track when the client sends EXCHANGE_ID to test
a new transport for session trunking.
nfs4_detect_session_trunking() tests for trunking and returns
EINVAL if trunking can't be done, add EINVAL mapping to
show_nfs4_status() in tracepoints.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
To allow event log info access after boot, EFI boot stub extracts
the event log information and installs it in an EFI configuration
table. Currently, EFI boot stub only supports installation of event
log only for TPM 1.2 and TPM 2.0 protocols. Extend the same support
for CC protocol. Since CC platform also uses TCG2 format, reuse TPM2
support code as much as possible.
Link: https://uefi.org/specs/UEFI/2.10/38_Confidential_Computing.html#efi-cc-measurement-protocol [1]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lkml.kernel.org/r/0229a87e-fb19-4dad-99fc-4afd7ed4099a%40collabora.com
[ardb: Split out final events table handling to avoid version confusion]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
If the virtual firmware implements TPM support, TCG2 protocol will be
used for kernel measurements and event logging support. But in CC
environment, not all platforms support or enable the TPM feature. UEFI
specification [1] exposes protocol and interfaces used for kernel
measurements in CC platforms without TPM support.
More details about the EFI CC measurements and logging can be found
in [1].
Link: https://uefi.org/specs/UEFI/2.10/38_Confidential_Computing.html#efi-cc-measurement-protocol [1]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[ardb: Drop code changes, keep typedefs and #define's only]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The LINUX_EFI_ GUID identifiers are only intended to be used to refer to
GUIDs that are part of the Linux implementation, and are not considered
external ABI. (Famous last words).
GUIDs that already have a symbolic name in the spec should use that
name, to avoid confusion between firmware components. So use the
official name EFI_TCG2_FINAL_EVENTS_TABLE_GUID for the TCG2 'final
events' configuration table.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Multi-PF netdev (Socket Direct)
This series adds support for combining multiple devices (PFs) of the
same port under one netdev instance. Passing traffic through different
devices belonging to different NUMA sockets saves cross-numa traffic and
allows apps running on the same netdev from different numas to still
feel a sense of proximity to the device and achieve improved
performance.
We achieve this by grouping PFs together, and creating the netdev only
once all group members are probed. Symmetrically, we destroy the netdev
once any of the PFs is removed.
The channels are distributed between all devices, a proper configuration
would utilize the correct close numa when working on a certain app/cpu.
We pick one device to be a primary (leader), and it fills a special
role. The other devices (secondaries) are disconnected from the network
in the chip level (set to silent mode). All RX/TX traffic is steered
through the primary to/from the secondaries.
Currently, we limit the support to PFs only, and up to two devices
(sockets).
* tag 'mlx5-socket-direct-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
Documentation: networking: Add description for multi-pf netdev
net/mlx5: Enable SD feature
net/mlx5e: Block TLS device offload on combined SD netdev
net/mlx5e: Support per-mdev queue counter
net/mlx5e: Support cross-vhca RSS
net/mlx5e: Let channels be SD-aware
net/mlx5e: Create EN core HW resources for all secondary devices
net/mlx5e: Create single netdev per SD group
net/mlx5: SD, Add debugfs
net/mlx5: SD, Add informative prints in kernel log
net/mlx5: SD, Implement steering for primary and secondaries
net/mlx5: SD, Implement devcom communication and primary election
net/mlx5: SD, Implement basic query and instantiation
net/mlx5: SD, Introduce SD lib
net/mlx5: Add MPIR bit in mcam_access_reg
====================
Link: https://lore.kernel.org/r/20240307084229.500776-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- hci_conn: Only do ACL connections sequentially
- hci_core: Cancel request on command timeout
- Remove CONFIG_BT_HS
- btrtl: Add the support for RTL8852BT/RTL8852BE-VT
- btusb: Add support Mediatek MT7920
- btusb: Add new VID/PID 13d3/3602 for MT7925
- Add new quirk for broken read key length on ATS2851
* tag 'for-net-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (52 commits)
Bluetooth: hci_sync: Fix UAF in hci_acl_create_conn_sync
Bluetooth: Fix eir name length
Bluetooth: ISO: Align broadcast sync_timeout with connection timeout
Bluetooth: Add new quirk for broken read key length on ATS2851
Bluetooth: mgmt: remove NULL check in add_ext_adv_params_complete()
Bluetooth: mgmt: remove NULL check in mgmt_set_connectable_complete()
Bluetooth: btusb: Add support Mediatek MT7920
Bluetooth: btmtk: Add MODULE_FIRMWARE() for MT7922
Bluetooth: btnxpuart: Fix btnxpuart_close
Bluetooth: ISO: Clean up returns values in iso_connect_ind()
Bluetooth: fix use-after-free in accessing skb after sending it
Bluetooth: af_bluetooth: Fix deadlock
Bluetooth: bnep: Fix out-of-bound access
Bluetooth: btusb: Fix memory leak
Bluetooth: msft: Fix memory leak
Bluetooth: hci_core: Fix possible buffer overflow
Bluetooth: btrtl: fix out of bounds memory access
Bluetooth: hci_h5: Add ability to allocate memory for private data
Bluetooth: hci_sync: Fix overwriting request callback
Bluetooth: hci_sync: Use QoS to determine which PHY to scan
...
====================
Link: https://lore.kernel.org/r/20240308181056.120547-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2024-03-07
Various cross tree patches for ieee802154v drivers and a resource leak
fix for ieee802154 llsec.
Andy Shevchenko changed GPIO header usage for at86rf230 and mcr20a to
only include needed headers.
Bo Liu converted the at86rf230, mcr20a and mrf24j40 driver regmap
support to use the maple tree register cache.
Fedor Pchelkin fixed a resource leak in the llsec key deletion path.
Ricardo B. Marliere made wpan_phy_class const.
Tejun Heo removed WQ_UNBOUND from a workqueue call in ca8210.
* tag 'ieee802154-for-net-next-2024-03-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan-next:
ieee802154: cfg802154: make wpan_phy_class constant
ieee802154: mcr20a: Remove unused of_gpio.h
ieee802154: at86rf230: Replace of_gpio.h by proper one
mac802154: fix llsec key resources release in mac802154_llsec_key_del
ieee802154: ca8210: Drop spurious WQ_UNBOUND from alloc_ordered_workqueue() call
net: ieee802154: mrf24j40: convert to use maple tree register cache
net: ieee802154: mcr20a: convert to use maple tree register cache
net: ieee802154: at86rf230: convert to use maple tree register cache
====================
Link: https://lore.kernel.org/r/20240307195105.292085-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both AER and DPC RP PIO provide TLP Header Log registers (PCIe r6.1 secs
7.8.4 & 7.9.14) to convey error diagnostics but the struct is named after
AER as the struct aer_header_log_regs. Also, not all places that handle TLP
Header Log use the struct and the struct members are named individually.
Generalize the struct name and members, and use it consistently where TLP
Header Log is being handled so that a pcie_read_tlp_log() helper can be
easily added.
Link: https://lore.kernel.org/r/20240206135717.8565-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: drop ixgbe changes for now, tidy whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Similar to skb_unref(), add skb_data_unref() to save an expensive
atomic operation (and cache line dirtying) when last reference
on shinfo->dataref is released.
I saw this opportunity on hosts with RAW sockets accidentally
bound to UDP protocol, forcing an skb_clone() on all received packets.
These RAW sockets had their receive queue full, so all clone
packets were immediately dropped.
When UDP recvmsg() consumes later the original skb, skb_release_data()
is hitting atomic_sub_return() quite badly, because skb->clone
has been set permanently.
Note that this patch helps TCP TX performance, because
TCP stack also use (fast) clones.
This means that at least one of the two packets (the main skb or
its clone) will no longer have to perform this atomic operation
in skb_release_data().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240307123446.2302230-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When enabling CONFIG_OF on a platform where 'of_root' is not populated
by firmware, we end up without a root node. In order to apply overlays
and create subnodes of the root node, we need one. Create this root node
by unflattening an empty builtin dtb.
If firmware provides a flattened device tree (FDT) then the FDT is
unflattened via setup_arch(). Otherwise, the call to
unflatten(_and_copy)?_device_tree() will create an empty root node.
We make of_have_populated_dt() return true only if the DTB was loaded by
firmware so that existing callers don't change behavior after this
patch. The call in the of platform code is removed because it prevents
overlays from creating platform devices when the empty root node is
used.
[sboyd@kernel.org: Update of_have_populated_dt() to treat this empty dtb
as not populated. Drop setup_of() initcall]
Signed-off-by: Frank Rowand <frowand.list@gmail.com>
Link: https://lore.kernel.org/r/20230317053415.2254616-2-frowand.list@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240217010557.2381548-3-sboyd@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
* tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (125 commits)
wifi: rtw89: wow: move release offload packet earlier for WoWLAN mode
wifi: rtw89: wow: set security engine options for 802.11ax chips only
wifi: rtw89: update suspend/resume for different generation
wifi: rtw89: wow: update config mac function with different generation
wifi: rtw89: update DMA function with different generation
wifi: rtw89: wow: update WoWLAN status register for different generation
wifi: rtw89: wow: update WoWLAN reason register for different chips
wifi: brcm80211: handle pmk_op allocation failure
wifi: rtw89: coex: Add coexistence policy to decrease WiFi packet CRC-ERR
wifi: rtw89: coex: When Bluetooth not available don't set power/gain
wifi: rtw89: coex: add return value to ensure H2C command is success or not
wifi: rtw89: coex: Reorder H2C command index to align with firmware
wifi: rtw89: coex: add BTC ctrl_info version 7 and related logic
wifi: rtw89: coex: add init_info H2C command format version 7
wifi: rtw89: 8922a: add coexistence helpers of SW grant
wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt
wifi: cw1200: restore endian swapping
wifi: wlcore: sdio: Rate limit wl12xx_sdio_raw_{read,write}() failures warns
wifi: rtlwifi: Remove rtl_intf_ops.read_efuse_byte
wifi: rtw88: 8821c: Fix false alarm count
...
====================
Link: https://lore.kernel.org/r/20240308100429.B8EA2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CS35L54 and CS35L57 are Boosted Smart Amplifiers. The CS35L54 has
I2C/SPI control and I2S/TDM audio. The CS35L57 also has SoundWire
control and audio.
The hardware differences between L54, L56 and L57 do not affect the
driver control interface so they can all be handled by the same driver.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240308135900.603192-2-rf@opensource.cirrus.com>
|
|
We only use the flag for this purpose, so rename it accordingly. This
further prevents various other use cases of it, keeping it clean and
consistent. Then we can also check it in one spot, when it's being
attempted recycled, and remove some dead code in io_kbuf_recycle_ring().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the rtc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240305-class_cleanup-abelloni-v1-1-944c026137c8@marliere.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add netlink support for reading NH group hardware stats.
Stats collection is done through a new notifier,
NEXTHOP_EVENT_HW_STATS_REPORT_DELTA. Drivers that implement HW counters for
a given NH group are thereby asked to collect the stats and report back to
core by calling nh_grp_hw_stats_report_delta(). This is similar to what
netdevice L3 stats do.
Besides exposing number of packets that passed in the HW datapath, also
include information on whether any driver actually realizes the counters.
The core can tell based on whether it got any _report_delta() reports from
the drivers. This allows enabling the statistics at the group at any time,
with drivers opting into supporting them. This is also in line with what
netdevice L3 stats are doing.
So as not to waste time and space, tie the collection and reporting of HW
stats with a new op flag, NHA_OP_FLAG_DUMP_HW_STATS.
Co-developed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Kees Cook <keescook@chromium.org> # For the __counted_by bits
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink support for enabling collection of HW statistics on nexthop
groups.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add hw_stats field to several notifier structures to communicate to the
drivers that HW statistics should be configured for nexthops within a given
group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink support for reading NH group stats.
This data is only for statistics of the traffic in the SW datapath. HW
nexthop group statistics will be added in the following patches.
Emission of the stats is keyed to a new op_stats flag to avoid cluttering
the netlink message with stats if the user doesn't need them:
NHA_OP_FLAG_DUMP_STATS.
Co-developed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add nexthop group entry stats to count the number of packets forwarded
via each nexthop in the group. The stats will be exposed to user space
for better data path observability in the next patch.
The per-CPU stats pointer is placed at the beginning of 'struct
nh_grp_entry', so that all the fields accessed for the data path reside
on the same cache line:
struct nh_grp_entry {
struct nexthop * nh; /* 0 8 */
struct nh_grp_entry_stats * stats; /* 8 8 */
u8 weight; /* 16 1 */
/* XXX 7 bytes hole, try to pack */
union {
struct {
atomic_t upper_bound; /* 24 4 */
} hthr; /* 24 4 */
struct {
struct list_head uw_nh_entry; /* 24 16 */
u16 count_buckets; /* 40 2 */
u16 wants_buckets; /* 42 2 */
} res; /* 24 24 */
}; /* 24 24 */
struct list_head nh_list; /* 48 16 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct nexthop * nh_parent; /* 64 8 */
/* size: 72, cachelines: 2, members: 6 */
/* sum members: 65, holes: 1, sum holes: 7 */
/* last cacheline: 8 bytes */
};
Co-developed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to add per-nexthop statistics, but still not increase netlink
message size for consumers that do not care about them, there needs to be a
toggle through which the user indicates their desire to get the statistics.
To that end, add a new attribute, NHA_OP_FLAGS. The idea is to be able to
use the attribute for carrying of arbitrary operation-specific flags, i.e.
not make it specific for get / dump.
Add the new attribute to get and dump policies, but do not actually allow
any flags yet -- those will come later as the flags themselves are defined.
Add the necessary parsing code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is useful to expose skb addr and sock addr to user in tracepoint
tcp_probe, so that we can get more information while monitoring
receiving of tcp data, by ebpf or other ways.
For example, we need to identify a packet by seq and end_seq when
calculate transmit latency between layer 2 and layer 4 by ebpf, but which is
not available in tcp_probe, so we can only use kprobe hooking
tcp_rcv_established to get them. But we can use tcp_probe directly if skb
addr and sock addr are available, which is more efficient.
Signed-off-by: fuyuanli <fuyuanli@didiglobal.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
softnet_data->time_squeeze is sometimes used as a proxy for
host overload or indication of scheduling problems. In practice
this statistic is very noisy and has hard to grasp units -
e.g. is 10 squeezes a second to be expected, or high?
Delaying network (NAPI) processing leads to drops on NIC queues
but also RTT bloat, impacting pacing and CA decisions.
Stalls are a little hard to detect on the Rx side, because
there may simply have not been any packets received in given
period of time. Packet timestamps help a little bit, but
again we don't know if packets are stale because we're
not keeping up or because someone (*cough* cgroups)
disabled IRQs for a long time.
We can, however, use Tx as a proxy for Rx stalls. Most drivers
use combined Rx+Tx NAPIs so if Tx gets starved so will Rx.
On the Tx side we know exactly when packets get queued,
and completed, so there is no uncertainty.
This patch adds stall checks to BQL. Why BQL? Because
it's a convenient place to add such checks, already
called by most drivers, and it has copious free space
in its structures (this patch adds no extra cache
references or dirtying to the fast path).
The algorithm takes one parameter - max delay AKA stall
threshold and increments a counter whenever NAPI got delayed
for at least that amount of time. It also records the length
of the longest stall.
To be precise every time NAPI has not polled for at least
stall thrs we check if there were any Tx packets queued
between last NAPI run and now - stall_thrs/2.
Unlike the classic Tx watchdog this mechanism does not
ignore stalls caused by Tx being disabled, or loss of link.
I don't think the check is worth the complexity, and
stall is a stall, whether due to host overload, flow
control, link down... doesn't matter much to the application.
We have been running this detector in production at Meta
for 2 years, with the threshold of 8ms. It's the lowest
value where false positives become rare. There's still
a constant stream of reported stalls (especially without
the ksoftirqd deferral patches reverted), those who like
their stall metrics to be 0 may prefer higher value.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
