| Age | Commit message (Collapse) | Author |
|---|
|
In Samsung devices, the method used to compensate for temperature,
age, load etc is by way of VBAT to Ri tables, which correlates the
battery voltage under load (VBAT) to an internal resistance (Ri).
Using this Ri and a measurement of the current out of the battery
(IBAT) the open circuit voltage (OCV) can be calculated as:
OCV = VBAT - (Ri * IBAT)
The details are described in comments to struct
power_supply_battery_info in the commit.
Since not all batteries supply this VBAT-to-Ri data, the fallback
method to use the temperature-to-Ri lookup table can also be used
as a fallback.
Add two helper functions to check if we have the tables needed for
using power_supply_vbat2ri() or power_supply_temp2resist_simple()
respectively, so capacity estimation code can choose which one
to employ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Battery Type Indicator (BTI) resistor is a resistor mounted
between a special terminal on the battery and ground. By sending
a fixed current (such as 7mA) through this resistor and measuring
the voltage over it, the resistance can be determined, and this
verifies the battery type.
Typical side view of the battery:
o o o
GND BTI +3.8V
Typical example of the electrical layout:
+3.8 V BTI
| |
| + |
_______ [ ] 7kOhm
___ |
| |
| |
GND GND
By verifying this resistance before attempting to charge the
battery we add an additional level of security.
In some systems this is used for plug-and-play of batteries with
different capacity. In other cases, this is merely used to verify
that the right type of battery is connected, if several batteries
have the same physical shape and can be plugged into the same
slot. Sometimes this is just a surplus security mechanism.
Nokia and Samsung among many other vendors are known to use these
BTI resistors.
Add the BTI properties to struct power_supply_battery_info and
switch the AB8500 charger code over to using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The AB8500 code is using a special current and voltage setting
when the battery is in "alert mode", i.e. when it is starting
to go outside normal operating conditions so it is too
cold or too hot. This makes sense as a way for the charging
algorithm to deal with hostile environments.
Add the needed members to the struct power_supply_battery_info,
and switch the AB8500 charging code over to using this.
Reviewed-by: Matti Vaittineen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Maintenance charging is the phase of keeping up the charge
after the battery has charged fully using CC/CV charging.
This can be done in many successive phases and is usually
done with a slightly lower constant voltage than CV, and
a slightly lower allowed current.
Add an array of maintenance charging points each with a
current, voltage and safety timer, and add helper functions
to use these. Migrate the AB8500 code over.
This is used in several Samsung products using the AB8500
and these batteries and their complete parameters will
be added later as full examples, but the default battery
in the AB8500 code serves as a reasonable example so far.
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_drm_dev_alloc() can't allocate structures that embed a structure
which then again embeds drm_device. Workaround this by adding a
driver_private pointer to struct mipi_dbi_dev which the driver can use for
its additional state.
v3:
- Add documentation
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-5-noralf@tronnes.org
|
|
Add a function to get a drm_display_mode from a panel-timing
device tree subnode.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-4-noralf@tronnes.org
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the driver core fix in here as well for future changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the char-misc fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Nobody checks the return codes, so make them return void. Indeed, if the
LLDD cannot send an event, nothing much can be done in the LLDD about it.
Also remove prototype for sas_notify_phy_event() in sas_internal.h, which
should not be there.
Link: https://lore.kernel.org/r/1645786656-221630-2-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use flexible-array members in struct fc_fdmi_attr_entry and fs_fdmi_attrs
instead of one-element arrays, and refactor the code accordingly.
Also, this helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
https://github.com/KSPP/linux/issues/79
https://github.com/ClangBuiltLinux/linux/issues/1590
Link: https://lore.kernel.org/r/20220214223903.GA859464@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
pwm[1-*]_auto_channels_temp is documented as an official
hwmon sysfs attribute, yet there is no support for it in
the new with_info-API. Fix that.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220224061210.16452-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull dma-mapping fix from Christoph Hellwig:
- fix a swiotlb info leak (Halil Pasic)
* tag 'dma-mapping-5.17-1' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix info leak with DMA_FROM_DEVICE
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields. Wrap the target region
in struct_group(). This additionally fixes a theoretical misalignment
of the copy (since the size of "buf" changes between 64-bit and 32-bit,
but this is likely never built for 64-bit).
FWIW, I think this code is totally broken on 64-bit (which appears to
not be a "real" build configuration): it would either always fail (with
an uninitialized data->buf_size) or would cause corruption in userspace
due to the copy_to_user() in the call path against an uninitialized
data->buf value:
omap3isp_stat_request_statistics_time32(...)
struct omap3isp_stat_data data64;
...
omap3isp_stat_request_statistics(stat, &data64);
int omap3isp_stat_request_statistics(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
buf = isp_stat_buf_get(stat, data);
static struct ispstat_buffer *isp_stat_buf_get(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
if (buf->buf_size > data->buf_size) {
...
return ERR_PTR(-EINVAL);
}
...
rval = copy_to_user(data->buf,
buf->virt_addr,
buf->buf_size);
Regardless, additionally initialize data64 to be zero-filled to avoid
undefined behavior.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: linux-media@vger.kernel.org
Fixes: 378e3f81cb56 ("media: omap3isp: support 64-bit version of omap3isp_stat_data")
Cc: stable@vger.kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/lkml/20211215220505.GB21862@embeddedor
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This is a preparatory change required for the addition of temperature
sensing front ends.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In preparation for the addition of kunit tests, expose the logic
responsible for combining channel scales.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-2-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_8021q_bridge_tx_fwd_offload_vid is no longer used just for
bridge TX forwarding offload, it is the private VLAN reserved for
VLAN-unaware bridging in a way that is compatible with FDB isolation.
So just rename it dsa_tag_8021q_bridge_vid.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the old Shared VLAN Learning mode of operation that tag_8021q
previously used for forwarding, we needed to have distinct concepts for
an RX and a TX VLAN.
An RX VLAN could be installed on all ports that were members of a given
bridge, so that autonomous forwarding could still work, while a TX VLAN
was dedicated for precise packet steering, so it just contained the CPU
port and one egress port.
Now that tag_8021q uses Independent VLAN Learning and imprecise RX/TX
all over, those lines have been blurred and we no longer have the need
to do precise TX towards a port that is in a bridge. As for standalone
ports, it is fine to use the same VLAN ID for both RX and TX.
This patch changes the tag_8021q format by shifting the VLAN range it
reserves, and halving it. Previously, our DIR bits were encoding the
VLAN direction (RX/TX) and were set to either 1 or 2. This meant that
tag_8021q reserved 2K VLANs, or 50% of the available range.
Change the DIR bits to a hardcoded value of 3 now, which makes tag_8021q
reserve only 1K VLANs, and a different range now (the last 1K). This is
done so that we leave the old format in place in case we need to return
to it.
In terms of code, the vid_is_dsa_8021q_rxvlan and vid_is_dsa_8021q_txvlan
functions go away. Any vid_is_dsa_8021q is both a TX and an RX VLAN, and
they are no longer distinct. For example, felix which did different
things for different VLAN types, now needs to handle the RX and the TX
logic for the same VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105 switch can't populate the PORT field of the tag_8021q header
when sending a frame to the CPU with a non-zero VBID.
Similar to dsa_find_designated_bridge_port_by_vid() which performs
imprecise RX for VLAN-aware bridges, let's introduce a helper in
tag_8021q for performing imprecise RX based on the VLAN that it has
allocated for a VLAN-unaware bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce migration IFC related stuff to enable migration commands.
Link: https://lore.kernel.org/all/20220224142024.147653-7-yishaih@nvidia.com
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Expose an API to get the mlx5 core device from a given VF PCI device if
mlx5_core is its driver.
Upon the get API we stay with the intf_state_mutex locked to make sure
that the device can't be gone/unloaded till the caller will complete
its job over the device, this expects to be for a short period of time
for any flow that the lock is taken.
Upon the put API we unlock the intf_state_mutex.
The use case for those APIs is the migration flow of a VF over VFIO PCI.
In that case the VF doesn't ride on mlx5_core, because the device is
driving *two* different PCI devices, the PF owned by mlx5_core and the
VF owned by the vfio driver.
The mlx5_core of the PF is accessed only during the narrow window of the
VF's ioctl that requires its services.
This allows the PF driver to be more independent of the VF driver, so
long as it doesn't reset the FW.
Link: https://lore.kernel.org/all/20220224142024.147653-6-yishaih@nvidia.com
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
There are some cases where a SR-IOV VF driver will need to reach into and
interact with the PF driver. This requires accessing the drvdata of the PF.
Provide a function pci_iov_get_pf_drvdata() to return this PF drvdata in a
safe way. Normally accessing a drvdata of a foreign struct device would be
done using the device_lock() to protect against device driver
probe()/remove() races.
However, due to the design of pci_enable_sriov() this will result in a
ABBA deadlock on the device_lock as the PF's device_lock is held during PF
sriov_configure() while calling pci_enable_sriov() which in turn holds the
VF's device_lock while calling VF probe(), and similarly for remove.
This means the VF driver can never obtain the PF's device_lock.
Instead use the implicit locking created by pci_enable/disable_sriov(). A
VF driver can access its PF drvdata only while its own driver is attached,
and the PF driver can control access to its own drvdata based on when it
calls pci_enable/disable_sriov().
To use this API the PF driver will setup the PF drvdata in the probe()
function. pci_enable_sriov() is only called from sriov_configure() which
cannot happen until probe() completes, ensuring no VF races with drvdata
setup.
For removal, the PF driver must call pci_disable_sriov() in its remove
function before destroying any of the drvdata. This ensures that all VF
drivers are unbound before returning, fencing concurrent access to the
drvdata.
The introduction of a new function to do this access makes clear the
special locking scheme and the documents the requirements on the PF/VF
drivers using this.
Link: https://lore.kernel.org/all/20220224142024.147653-5-yishaih@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The PCI core uses the VF index internally, often called the vf_id,
during the setup of the VF, eg pci_iov_add_virtfn().
This index is needed for device drivers that implement live migration
for their internal operations that configure/control their VFs.
Specifically, mlx5_vfio_pci driver that is introduced in coming patches
from this series needs it and not the bus/device/function which is
exposed today.
Add pci_iov_vf_id() which computes the vf_id by reversing the math that
was used to create the bus/device/function.
Link: https://lore.kernel.org/all/20220224142024.147653-2-yishaih@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- rtla (Real-Time Linux Analysis tool):
- fix typo in man page
- Update API -e to -E before it is released
- Error message fix and memory leak fix
- Partially uninline trace event soft disable to shrink text
- Fix function graph start up test
- Have triggers affect the trace instance they are in and not top level
- Have osnoise sleep in the units it says it uses
- Remove unused ftrace stub function
- Remove event probe redundant info from event in the buffer
- Fix group ownership setting in tracefs
- Ensure trace buffer is minimum size to prevent crashes
* tag 'trace-v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rtla/osnoise: Fix error message when failing to enable trace instance
rtla/osnoise: Free params at the exit
rtla/hist: Make -E the short version of --entries
tracing: Fix selftest config check for function graph start up test
tracefs: Set the group ownership in apply_options() not parse_options()
tracing/osnoise: Make osnoise_main to sleep for microseconds
ftrace: Remove unused ftrace_startup_enable() stub
tracing: Ensure trace buffer is at least 4096 bytes large
tracing: Uninline trace_trigger_soft_disabled() partly
eprobes: Remove redundant event type information
tracing: Have traceon and traceoff trigger honor the instance
tracing: Dump stacktrace trigger to the corresponding instance
rtla: Fix systme -> system typo on man page
|
|
Replace kfree_skb() used in __neigh_event_send() with
kfree_skb_reason(). Following drop reasons are added:
SKB_DROP_REASON_NEIGH_FAILED
SKB_DROP_REASON_NEIGH_QUEUEFULL
SKB_DROP_REASON_NEIGH_DEAD
The first two reasons above should be the hot path that skb drops
in neighbour subsystem.
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace kfree_skb() which is used in the packet egress path of IP layer
with kfree_skb_reason(). Functions that are involved include:
__ip_queue_xmit()
ip_finish_output()
ip_mc_finish_output()
ip6_output()
ip6_finish_output()
ip6_finish_output2()
Following new drop reasons are introduced:
SKB_DROP_REASON_IP_OUTNOROUTES
SKB_DROP_REASON_BPF_CGROUP_EGRESS
SKB_DROP_REASON_IPV6DISABLED
SKB_DROP_REASON_NEIGH_CREATEFAIL
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's handy to have an ldisc number free for out-of-tree testing. This
way, a new ldisc can be developed on any running system, without having
to recompile the kernel just to define a new number.
This is the highest number (and also the last one) available under the
old numbering scheme, so let's reserve it before it's too late.
From now on, every new ldisc upstreamed will have to increment NR_LDISCS
in lockstep with its addition to the table in tty.h.
Signed-off-by: Max Staudt <max@enpas.org>
Link: https://lore.kernel.org/r/20220211141036.6403-1-max@enpas.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Sunplus SoC UART Driver.
SP7021 UART block contains 5 UARTs.
There are UART0~4 that supported in SP7021, the features list as below.
Support Full-duplex communication.
Support data packet length configurable.
Support stop bit number configurable.
Support force break condition.
Support baud rate configurable.
Support error detection and report.
Support RXD Noise Rejection Vote configurable.
UART0 pinout only support TX/RX two pins.
UART1 to UART4 pinout support TX/RX/CTS/RTS four pins.
Normally UART0 used for kernel console, also can be used for normal uart.
Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port.
UART driver probe will create path named "/dev/ttySUPx".
https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch kills t_handle_lock transaction spinlock completely from
jbd2.
To explain the reasoning, currently there were three sites at which
this spinlock was used.
1. jbd2_journal_wait_updates()
a. Based on careful code review it can be seen that, we don't need this
lock here. This is since we wait for any currently ongoing updates
based on a atomic variable t_updates. And we anyway don't take any
t_handle_lock while in stop_this_handle().
i.e.
write_lock(&journal->j_state_lock()
jbd2_journal_wait_updates() stop_this_handle()
while (atomic_read(txn->t_updates) { |
DEFINE_WAIT(wait); |
prepare_to_wait(); |
if (atomic_read(txn->t_updates) if (atomic_dec_and_test(txn->t_updates))
write_unlock(&journal->j_state_lock);
schedule(); wake_up()
write_lock(&journal->j_state_lock);
finish_wait();
}
txn->t_state = T_COMMIT
write_unlock(&journal->j_state_lock);
b. Also note that between atomic_inc(&txn->t_updates) in
start_this_handle() and jbd2_journal_wait_updates(), the
synchronization happens via read_lock(journal->j_state_lock) in
start_this_handle();
2. jbd2_journal_extend()
a. jbd2_journal_extend() is called with the handle of each process from
task_struct. So no lock required in updating member fields of handle_t
b. For member fields of h_transaction, all updates happens only via
atomic APIs (which is also within read_lock()).
So, no need of this transaction spinlock.
3. update_t_max_wait()
Based on Jan suggestion, this can be carefully removed using atomic
cmpxchg API.
Note that there can be several processes which are waiting for a new
transaction to be allocated and started. For doing this only one
process will succeed in taking write_lock() and allocating a new txn.
After that all of the process will be updating the t_max_wait (max
transaction wait time). This can be done via below method w/o taking
any locks using atomic cmpxchg.
For more details refer [1]
new = get_new_val();
old = READ_ONCE(ptr->max_val);
while (old < new)
old = cmpxchg(&ptr->max_val, old, new);
[1]: https://lwn.net/Articles/849237/
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/d89e599658b4a1f3893a48c6feded200073037fc.1644992076.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The elements of the table are never modified in clk-mux.c. To make this
clear to clock drivers, declare the parameter as const u32 *table.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20220205103613.1216218-4-j.neuschaefer@gmx.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Now that we have more fine grained attribute revalidation, let's just
get rid of NFS_INO_REVAL_PAGECACHE.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
In 4.1+, the server is allowed to set a flag
NFS4_RESULT_PRESERVE_UNLINKED in reply to the OPEN, that tells
the client that it does not need to do a silly rename of an
opened file when it's being removed.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix the throttle IRQ handling during cpufreq initialization on
Qualcomm platforms (Bjorn Andersson)"
* tag 'pm-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
|
|
NFS is one of the last two users of the deprecated ->readpages aop.
This conversion looks straightforward, but I have only compile-tested
it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
On a powerpc32 build with CONFIG_CC_OPTIMISE_FOR_SIZE, the inline
keyword is not honored and trace_trigger_soft_disabled() appears
approx 50 times in vmlinux.
Adding -Winline to the build, the following message appears:
./include/linux/trace_events.h:712:1: error: inlining failed in call to 'trace_trigger_soft_disabled': call is unlikely and code size would grow [-Werror=inline]
That function is rather big for an inlined function:
c003df60 <trace_trigger_soft_disabled>:
c003df60: 94 21 ff f0 stwu r1,-16(r1)
c003df64: 7c 08 02 a6 mflr r0
c003df68: 90 01 00 14 stw r0,20(r1)
c003df6c: bf c1 00 08 stmw r30,8(r1)
c003df70: 83 e3 00 24 lwz r31,36(r3)
c003df74: 73 e9 01 00 andi. r9,r31,256
c003df78: 41 82 00 10 beq c003df88 <trace_trigger_soft_disabled+0x28>
c003df7c: 38 60 00 00 li r3,0
c003df80: 39 61 00 10 addi r11,r1,16
c003df84: 4b fd 60 ac b c0014030 <_rest32gpr_30_x>
c003df88: 73 e9 00 80 andi. r9,r31,128
c003df8c: 7c 7e 1b 78 mr r30,r3
c003df90: 41 a2 00 14 beq c003dfa4 <trace_trigger_soft_disabled+0x44>
c003df94: 38 c0 00 00 li r6,0
c003df98: 38 a0 00 00 li r5,0
c003df9c: 38 80 00 00 li r4,0
c003dfa0: 48 05 c5 f1 bl c009a590 <event_triggers_call>
c003dfa4: 73 e9 00 40 andi. r9,r31,64
c003dfa8: 40 82 00 28 bne c003dfd0 <trace_trigger_soft_disabled+0x70>
c003dfac: 73 ff 02 00 andi. r31,r31,512
c003dfb0: 41 82 ff cc beq c003df7c <trace_trigger_soft_disabled+0x1c>
c003dfb4: 80 01 00 14 lwz r0,20(r1)
c003dfb8: 83 e1 00 0c lwz r31,12(r1)
c003dfbc: 7f c3 f3 78 mr r3,r30
c003dfc0: 83 c1 00 08 lwz r30,8(r1)
c003dfc4: 7c 08 03 a6 mtlr r0
c003dfc8: 38 21 00 10 addi r1,r1,16
c003dfcc: 48 05 6f 6c b c0094f38 <trace_event_ignore_this_pid>
c003dfd0: 38 60 00 01 li r3,1
c003dfd4: 4b ff ff ac b c003df80 <trace_trigger_soft_disabled+0x20>
However it is located in a hot path so inlining it is important.
But forcing inlining of the entire function by using __always_inline
leads to increasing the text size by approx 20 kbytes.
Instead, split the fonction in two parts, one part with the likely
fast path, flagged __always_inline, and a second part out of line.
With this change, on a powerpc32 with CONFIG_CC_OPTIMISE_FOR_SIZE
vmlinux text increases by only 1,4 kbytes, which is partly
compensated by a decrease of vmlinux data by 7 kbytes.
On ppc64_defconfig which has CONFIG_CC_OPTIMISE_FOR_SPEED, this
change reduces vmlinux text by more than 30 kbytes.
Link: https://lkml.kernel.org/r/69ce0986a52d026d381d612801d978aa4f977460.1644563295.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Some functions to create properties (drm_plane_create_zpos_property or
drm_plane_create_color_properties for example) will ask for a range of
acceptable value and an initial one.
This initial value is then stored in the values array for that property.
Let's provide an helper to access this property.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-7-maxime@cerno.tech
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung clock controller changes for v5.18
Add support for Tesla FSD SoC clock controller within Samsung Exynos SoC
clock controller drivers. The Tesla FSD's clock controller is similar
to Samsung Exynos one, so entire driver structure can be re-used.
* tag 'samsung-clk-fsd-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: fix missing Tesla FSD dependency on Exynos
clk: samsung: fsd: Add cam_csi block clock information
clk: samsung: fsd: Add cmu_mfc block clock information
clk: samsung: fsd: Add cmu_imem block clock information
clk: samsung: fsd: Add cmu_fsys1 clock information
clk: samsung: fsd: Add cmu_fsys0 clock information
clk: samsung: fsd: Add cmu_peric block clock information
clk: samsung: fsd: Add initial clock support
dt-bindings: clock: Document FSD CMU bindings
dt-bindings: clock: Add bindings definitions for FSD CMU blocks
Link: https://lore.kernel.org/r/20220204154112.133723-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
|
|
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
|
|
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
Arm SCMI firmware interface updates for v5.18
Few main additions include:
- Support for OPTEE based SCMI transport to enable using SCMI service
provided by OPTEE on some platforms
- Support for atomic SCMI transports which enables few SCMI transactions
to be completed in atomic context. This involves other refactoring work
associated with it. It also marks SMC and OPTEE as atomic transport as
the commands are completed once the return.
- Support for polling mode in SCMI VirtIO transport in order to support
atomic operations
- Support for atomic clock operations based on availability of atomic
capability in the underlying SCMI transport
Other changes involves some trace and log enhancements and miscellaneous
bug fixes.
* tag 'scmi-updates-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: (28 commits)
clk: scmi: Support atomic clock enable/disable API
firmware: arm_scmi: Add support for clock_enable_latency
firmware: arm_scmi: Add atomic support to clock protocol
firmware: arm_scmi: Support optional system wide atomic-threshold-us
dt-bindings: firmware: arm,scmi: Add atomic-threshold-us optional property
firmware: arm_scmi: Add atomic mode support to virtio transport
firmware: arm_scmi: Review virtio free_list handling
firmware: arm_scmi: Add a virtio channel refcount
firmware: arm_scmi: Disable ftrace for Clang Thumb2 builds
firmware: arm_scmi: Add new parameter to mark_txdone
firmware: arm_scmi: Add atomic mode support to smc transport
firmware: arm_scmi: Add support for atomic transports
firmware: arm_scmi: Make optee support sync_cmds_completed_on_ret
firmware: arm_scmi: Make smc support sync_cmds_completed_on_ret
firmware: arm_scmi: Add sync_cmds_completed_on_ret transport flag
firmware: arm_scmi: Make smc transport use common completions
firmware: arm_scmi: Add configurable polling mode for transports
firmware: arm_scmi: Use new trace event scmi_xfer_response_wait
include: trace: Add new scmi_xfer_response_wait event
firmware: arm_scmi: Refactor message response path
...
Link: https://lore.kernel.org/r/20220222201742.3338589-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.18:
- Drop LS1021A device check from soc-imx driver as it's unneeded since
commit commit 4ebd29f91629 ("soc: imx: Register SoC device only on
i.MX boards").
- Add support for power domains provided by the VPU blk-ctrl on the
i.MX8MQ.
- Add resource owner management API which will be used to check whether
M4 is under control of Linux.
- Add VPU MU resources support into SCU power domain driver.
- Support DT overlay for WEIM bus driver with OF reconfiguration
notifier handler.
* tag 'imx-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
bus: imx-weim: add DT overlay support for WEIM bus
firmware: imx: scu-pd: imx8q: add vpu mu resources
firmware: imx: add get resource owner api
soc: imx: imx8m-blk-ctrl: add i.MX8MQ VPU blk-ctrl
dt-bindings: power: imx8mq: add defines for VPU blk-ctrl domains
soc: imx: Remove Layerscape check
Link: https://lore.kernel.org/r/20220222075226.160187-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
