| Age | Commit message (Collapse) | Author |
|---|
|
Currently quirks are only allowed for Slave devices. This patch
describes the need for two quirks at the Master level.
a) bus clash
The SoundWire specification allows a Slave device to report a bus clash
with the in-band interrupt mechanism when it detects a conflict while
driving a bitSlot it owns. This can be a symptom of an electrical conflict
or a programming error, and it's vital to detect reliably.
Unfortunately, on some platforms, bus clashes are randomly reported by
Slave devices after a bus reset, with an interrupt status set even before
the bus clash interrupt is enabled. These initial spurious interrupts are
not relevant and should optionally be filtered out, while leaving the
interrupt mechanism enabled to detect 'true' issues.
This patch suggests the addition of a Master level quirk to discard such
interrupts. The quirk should in theory have been added at the Slave level,
but since the problem was detected with different generations of Slave
devices it's hard to point to a specific IP. The problem might also be
board-dependent and hence dealing with a Master quirk is simpler.
b) parity
Additional tests on a new platform with the Maxim 98373 amplifier
showed a rare case where the parity interrupt is also thrown on
startup, at the same time as bus clashes. This issue only seems to
happen infrequently and was only observed during suspend-resume stress
tests while audio is streaming. We could make the problem go away by
adding a Slave-level quirk, but there is no evidence that the issue is
actually a Slave problem: the parity is provided by the Master, which
could also set an invalid parity in corner cases.
BugLink: https://github.com/thesofproject/linux/issues/2578
BugLink: https://github.com/thesofproject/linux/issues/2533
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302082720.12322-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Platform firmware may have incorrect _ADR values causing the driver
probes to fail. Add the override_ops, which when configured will allow
for quirks based on DMI etc to override the addr values.
Co-developed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302075105.11515-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The imx3 camera driver has been removed a long time ago, so get
rid of this unused header file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The imx27/imx25 camera driver has been removed a long time ago,
so get rid of this unused header file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The plane size needs to be PAGE_ALIGNED, so it is not possible to have
sizes bigger than MAX_INT - PAGE_SIZE.
We already check for overflows when that happen:
if (size < vb->planes[plane].length)
goto free;
But it is good to explicitly state our max allowed value, in order to
align with the driver expectations.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
According to Rec. ITU-T T.872 (06/2012) 6.5.3
APP14 segment is for color encoding, it contains a transform flag, which
may have values of 0, 1 and 2 and are interpreted as follows:
0 - CMYK for images that are encoded with four components
- RGB for images that are encoded with three components
1 - An image encoded with three components using YCbCr colour encoding.
2 - An image encoded with four components using YCCK colour encoding.
This is used in imx-jpeg decoder, to distinguish between
YUV444 and RGB24.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The added format is V4L2_PIX_FMT_YUV24, this is a packed
YUV 4:4:4 format, with 8 bits for each component, 24 bits
per sample.
This format is used by the i.MX 8QuadMax and i.MX 8DualXPlus/8QuadXPlus
JPEG encoder/decoder.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix these kernel-doc warnings:
include/media/davinci/vpbe_osd.h:77: warning: Enum value 'PIXFMT_YCBCRI' not described in enum 'osd_pix_format'
include/media/davinci/vpbe_osd.h:77: warning: Enum value 'PIXFMT_YCRCBI' not described in enum 'osd_pix_format'
include/media/davinci/vpbe_osd.h:77: warning: Excess enum value 'PIXFMT_YCrCbI' description in 'osd_pix_format'
include/media/davinci/vpbe_osd.h:77: warning: Excess enum value 'PIXFMT_YCbCrI' description in 'osd_pix_format'
include/media/davinci/vpbe_osd.h:232: warning: expecting prototype for enum davinci_cursor_v_width. Prototype was for enum
osd_cursor_v_width instead
include/uapi/linux/uvcvideo.h:98: warning: Function parameter or member 'ns' not described in 'uvc_meta_buf'
include/uapi/linux/uvcvideo.h:98: warning: Function parameter or member 'sof' not described in 'uvc_meta_buf'
include/uapi/linux/uvcvideo.h:98: warning: Function parameter or member 'length' not described in 'uvc_meta_buf'
include/uapi/linux/uvcvideo.h:98: warning: Function parameter or member 'flags' not described in 'uvc_meta_buf'
include/uapi/linux/uvcvideo.h:98: warning: Function parameter or member 'buf' not described in 'uvc_meta_buf'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This fixes these kernel-doc warnings:
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI2C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_CVBS_VI4A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2A_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2B_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2C_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2A_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2B_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI2C_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI1C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3A' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3B' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_SVIDEO_VI4A_VI3C' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:70: warning: Enum value 'INPUT_INVALID' not described in enum 'tvp514x_input'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_10BIT_422_EMBEDDED_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_20BIT_422_SEPERATE_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_10BIT_422_SEPERATE_SYNC' not described in enum 'tvp514x_output'
include/media/i2c/tvp514x.h:82: warning: Enum value 'OUTPUT_INVALID' not described in enum 'tvp514x_output'
include/media/i2c/adv7343.h:38: warning: cannot understand function prototype: 'struct adv7343_power_mode '
include/media/i2c/s5k4ecgx.h:31: warning: expecting prototype for struct ss5k4ecgx_platform_data. Prototype was for struct
s5k4ecgx_platform_data instead
include/media/i2c/mt9t112.h:21: warning: cannot understand function prototype: 'struct mt9t112_platform_data '
include/media/i2c/noon010pc30.h:13: warning: Cannot understand * @clk_rate: the clock frequency in Hz
include/media/i2c/s5k6aa.h:45: warning: Function parameter or member 'bus_type' not described in 's5k6aa_platform_data'
include/media/i2c/tw9910.h:19: warning: cannot understand function prototype: 'enum tw9910_mpout_pin '
include/media/i2c/tw9910.h:36: warning: cannot understand function prototype: 'struct tw9910_video_info '
include/media/i2c/ov772x.h:53: warning: cannot understand function prototype: 'struct ov772x_camera_info '
include/media/i2c/s5c73m3.h:53: warning: Function parameter or member 'bus_type' not described in 's5c73m3_platform_data'
drivers/media/i2c/ccs/ccs-quirk.h:50: warning: Function parameter or member 'post_streamoff' not described in 'ccs_quirk'
drivers/media/i2c/ccs/ccs-quirk.h:50: warning: Function parameter or member 'flags' not described in 'ccs_quirk'
drivers/media/i2c/ccs/ccs-data.h:144: warning: expecting prototype for struct ccs_pdaf_pix_loc_block_desc. Prototype was for struct
ccs_pdaf_pix_loc_pixel_desc instead
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'token' not described in 'tvp514x_reg'
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'reg' not described in 'tvp514x_reg'
drivers/media/i2c/tvp514x_regs.h:272: warning: Function parameter or member 'val' not described in 'tvp514x_reg'
drivers/media/i2c/m5mols/m5mols.h:69: warning: Function parameter or member 'brightness' not described in 'm5mols_exif'
drivers/media/i2c/m5mols/m5mols.h:147: error: Cannot parse struct or union!
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN0' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN1' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN2' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN3' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN4' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN5' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN6' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_AIN7' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_HDMI' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TTL' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TXA' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_TXB' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:65: warning: Enum value 'ADV748X_PORT_MAX' not described in enum 'adv748x_ports'
drivers/media/i2c/adv748x/adv748x.h:199: warning: Function parameter or member 'i2c_clients' not described in 'adv748x_state'
drivers/media/i2c/adv748x/adv748x.h:199: warning: Function parameter or member 'regmap' not described in 'adv748x_state'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This patch fixes the following kernel-doc warnings:
include/uapi/linux/videodev2.h:996: warning: Function parameter or member 'm' not described in 'v4l2_plane'
include/uapi/linux/videodev2.h:996: warning: Function parameter or member 'reserved' not described in 'v4l2_plane'
include/uapi/linux/videodev2.h:1057: warning: Function parameter or member 'm' not described in 'v4l2_buffer'
include/uapi/linux/videodev2.h:1057: warning: Function parameter or member 'reserved2' not described in 'v4l2_buffer'
include/uapi/linux/videodev2.h:1057: warning: Function parameter or member 'reserved' not described in 'v4l2_buffer'
include/uapi/linux/videodev2.h:1068: warning: Function parameter or member 'tv' not described in 'v4l2_timeval_to_ns'
include/uapi/linux/videodev2.h:1068: warning: Excess function parameter 'ts' description in 'v4l2_timeval_to_ns'
include/uapi/linux/videodev2.h:1138: warning: Function parameter or member 'reserved' not described in 'v4l2_exportbuffer'
include/uapi/linux/videodev2.h:2237: warning: Function parameter or member 'reserved' not described in 'v4l2_plane_pix_format'
include/uapi/linux/videodev2.h:2270: warning: Function parameter or member 'hsv_enc' not described in 'v4l2_pix_format_mplane'
include/uapi/linux/videodev2.h:2270: warning: Function parameter or member 'reserved' not described in 'v4l2_pix_format_mplane'
include/uapi/linux/videodev2.h:2281: warning: Function parameter or member 'reserved' not described in 'v4l2_sdr_format'
include/uapi/linux/videodev2.h:2315: warning: Function parameter or member 'fmt' not described in 'v4l2_format'
include/uapi/linux/v4l2-subdev.h:53: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_format'
include/uapi/linux/v4l2-subdev.h:66: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_crop'
include/uapi/linux/v4l2-subdev.h:89: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_mbus_code_enum'
include/uapi/linux/v4l2-subdev.h:108: warning: Function parameter or member 'min_width' not described in 'v4l2_subdev_frame_size_enum'
include/uapi/linux/v4l2-subdev.h:108: warning: Function parameter or member 'max_width' not described in 'v4l2_subdev_frame_size_enum'
include/uapi/linux/v4l2-subdev.h:108: warning: Function parameter or member 'min_height' not described in 'v4l2_subdev_frame_size_enum'
include/uapi/linux/v4l2-subdev.h:108: warning: Function parameter or member 'max_height' not described in 'v4l2_subdev_frame_size_enum'
include/uapi/linux/v4l2-subdev.h:108: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_frame_size_enum'
include/uapi/linux/v4l2-subdev.h:119: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_frame_interval'
include/uapi/linux/v4l2-subdev.h:140: warning: Function parameter or member 'reserved' not described in 'v4l2_subdev_frame_interval_enum'
include/uapi/linux/cec.h:406: warning: Function parameter or member 'raw' not described in 'cec_connector_info'
include/uapi/linux/cec.h:470: warning: Function parameter or member 'flags' not described in 'cec_event'
include/media/v4l2-h264.h:82: warning: Function parameter or member 'reflist' not described in 'v4l2_h264_build_p_ref_list'
include/media/v4l2-h264.h:82: warning: expecting prototype for v4l2_h264_build_b_ref_lists(). Prototype was for v4l2_h264_build_p_ref_list()
instead
include/media/cec.h:50: warning: Function parameter or member 'lock' not described in 'cec_devnode'
include/media/v4l2-jpeg.h:122: warning: Function parameter or member 'num_dht' not described in 'v4l2_jpeg_header'
include/media/v4l2-jpeg.h:122: warning: Function parameter or member 'num_dqt' not described in 'v4l2_jpeg_header'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix following warnings:
./scripts/kernel-doc --none include/uapi/linux/v4l2-controls.h
include/uapi/linux/v4l2-controls.h:1727: warning: bad line:
include/uapi/linux/v4l2-controls.h:1853: warning: expecting prototype for struct v4l2_vp8_frame. Prototype was for struct v4l2_ctrl_vp8_frame instead
include/uapi/linux/v4l2-controls.h:1853: warning: Function parameter or member 'segment' not described in 'v4l2_ctrl_vp8_frame'
include/uapi/linux/v4l2-controls.h:1853: warning: Function parameter or member 'entropy' not described in 'v4l2_ctrl_vp8_frame'
include/uapi/linux/v4l2-controls.h:1853: warning: Function parameter or member 'coder_state' not described in 'v4l2_ctrl_vp8_frame'
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Until now, the VP8 V4L2 API was not exported as a public API,
and only defined in a private media header (media/vp8-ctrls.h).
The reason for this was a concern about the API not complete
and ready to support VP8 decoding hardware accelerators.
After reviewing the VP8 specification in detail, and now
that the API is able to support Cedrus and Hantro G1,
we can consider this ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Before we move the VP8 controls to a stable public header,
rename this macro so it's clearly V4L2-specific.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Move the VP8 stateless control types out of staging,
and re-number it to avoid any confusion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Since we are ready to stabilize the VP8 stateless API,
move the parsed VP8 pixel format.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In preparation for making the interface public,
document all the structures.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Rename to struct v4l2_vp8_loop_filter, which is closer to the
VP8 syntax. This change is only cosmetics, but since this API
is exposed to userspace, it's worth the trouble to get it consistent.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
It doesn't seem to add any clarity to have a "header" suffix in controls,
struct names and flags.
Since this just makes names too long without any benefit, just drop it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a control to enable inserting of AUD NALU into encoded
bitstream.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Make display delay and display delay enable MFC controls standard v4l
controls. This will allow reuse of the controls for other decoder
drivers. Also the new proposed controls are now codec agnostic because
they could be used for any codec.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
We need the usb/thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A sequence counter write section must be serialized or its internal
state can get corrupted. A plain seqcount_t does not contain the
information of which lock must be held to guaranteee write side
serialization.
For xfrm_state_hash_generation, use seqcount_spinlock_t instead of plain
seqcount_t. This allows to associate the spinlock used for write
serialization with the sequence counter. It thus enables lockdep to
verify that the write serialization lock is indeed held before entering
the sequence counter write section.
If lockdep is disabled, this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
A sequence counter write section must be serialized or its internal
state can get corrupted. The "xfrm_state_hash_generation" seqcount is
global, but its write serialization lock (net->xfrm.xfrm_state_lock) is
instantiated per network namespace. The write protection is thus
insufficient.
To provide full protection, localize the sequence counter per network
namespace instead. This should be safe as both the seqcount read and
write sections access data exclusively within the network namespace. It
also lays the foundation for transforming "xfrm_state_hash_generation"
data type from seqcount_t to seqcount_LOCKNAME_t in further commits.
Fixes: b65e3d7be06f ("xfrm: state: add sequence count to detect hash resizes")
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The Frequency Invariance Engine (FIE) is providing a frequency scaling
correction factor that helps achieve more accurate load-tracking.
Normally, this scaling factor can be obtained directly with the help of
the cpufreq drivers as they know the exact frequency the hardware is
running at. But that isn't the case for CPPC cpufreq driver.
Another way of obtaining that is using the arch specific counter
support, which is already present in kernel, but that hardware is
optional for platforms.
This patch updates the CPPC driver to register itself with the topology
core to provide its own implementation (cppc_scale_freq_tick()) of
topology_scale_freq_tick() which gets called by the scheduler on every
tick. Note that the arch specific counters have higher priority than
CPPC counters, if available, though the CPPC driver doesn't need to have
any special handling for that.
On an invocation of cppc_scale_freq_tick(), we schedule an irq work
(since we reach here from hard-irq context), which then schedules a
normal work item and cppc_scale_freq_workfn() updates the per_cpu
arch_freq_scale variable based on the counter updates since the last
tick.
To allow platforms to disable this CPPC counter-based frequency
invariance support, this is all done under CONFIG_ACPI_CPPC_CPUFREQ_FIE,
which is enabled by default.
This also exports sched_setattr_nocheck() as the CPPC driver can be
built as a module.
Cc: linux-acpi@vger.kernel.org
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Tested-by: Ionela Voinescu <ionela.voinescu@arm.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Fix ~36 single-word typos in the IRQ, irqchip and irqdomain code comments.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix 3 single-word typos in the generic syscall entry code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix ~16 single-word typos in locking code comments.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix ~42 single-word typos in scheduler code comments.
We have accumulated a few fun ones over the years. :-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: linux-kernel@vger.kernel.org
|
|
Conflicts:
arch/x86/kernel/kprobes/ftrace.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add support for TI BQ78Z100, I2C interface gas gauge.
It provides a fully integrated safety protection
and authentication for 1 to 2-series cell Li-Ion and
Li-Polymer battery packs.
The patch was tested with BQ78Z100 equipment.
CASE I: Discharging:
POWER_SUPPLY_NAME=bq78z100-0
POWER_SUPPLY_STATUS=Discharging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=3386000
POWER_SUPPLY_CURRENT_NOW=-5000
POWER_SUPPLY_CAPACITY=27
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=269
POWER_SUPPLY_TIME_TO_EMPTY_NOW=1249920
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=6494000
POWER_SUPPLY_CHARGE_NOW=1736000
POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000
POWER_SUPPLY_CYCLE_COUNT=1
POWER_SUPPLY_POWER_AVG=-20000
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
CASE II : No discharging current:
POWER_SUPPLY_NAME=bq78z100-0
POWER_SUPPLY_STATUS=Not charging
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_VOLTAGE_NOW=3386000
POWER_SUPPLY_CURRENT_NOW=0
POWER_SUPPLY_CAPACITY=27
POWER_SUPPLY_CAPACITY_LEVEL=Normal
POWER_SUPPLY_TEMP=270
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CHARGE_FULL=6494000
POWER_SUPPLY_CHARGE_NOW=1734000
POWER_SUPPLY_CHARGE_FULL_DESIGN=6000000
POWER_SUPPLY_CYCLE_COUNT=1
POWER_SUPPLY_POWER_AVG=0
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_MANUFACTURER=Texas Instruments
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt driver fixes from Greg KH:
"Here are some small Thunderbolt and USB driver fixes for some reported
issues:
- thunderbolt fixes for minor problems
- typec fixes for power issues
- usb-storage quirk addition
- usbip bugfix
- dwc3 bugfix when stopping transfers
- cdnsp bugfix for isoc transfers
- gadget use-after-free fix
All have been in linux-next this week with no reported issues"
* tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy
usb: dwc3: gadget: Prevent EP queuing while stopping transfers
usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-
usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct
usb-storage: Add quirk to defeat Kindle's automatic unload
usb: gadget: configfs: Fix KASAN use-after-free
usbip: Fix incorrect double assignment to udc->ud.tcp_rx
usb: cdnsp: Fixes incorrect value in ISOC TRB
thunderbolt: Increase runtime PM reference count on DP tunnel discovery
thunderbolt: Initialize HopID IDAs in tb_switch_alloc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
- Get static calls & modules right. Hopefully.
- WW mutex fixes
* tag 'locking-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
static_call: Fix static_call_update() sanity check
static_call: Align static_call_is_init() patching condition
static_call: Fix static_call_set_init()
locking/ww_mutex: Fix acquire/release imbalance in ww_acquire_init()/ww_acquire_fini()
locking/ww_mutex: Simplify use_ww_ctx & ww_ctx handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
- another missing RT_PROP table related fix, to ensure that the
efivarfs pseudo filesystem fails gracefully if variable services
are unsupported
- use the correct alignment for literal EFI GUIDs
- fix a use after unmap issue in the memreserve code
* tag 'efi-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: use 32-bit alignment for efi_guid_t literals
firmware/efi: Fix a use after bug in efi_mem_reserve_persistent
efivars: respect EFI_UNSUPPORTED return from firmware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"The freshest pile of shiny x86 fixes for 5.12:
- Add the arch-specific mapping between physical and logical CPUs to
fix devicetree-node lookups
- Restore the IRQ2 ignore logic
- Fix get_nr_restart_syscall() to return the correct restart syscall
number. Split in a 4-patches set to avoid kABI breakage when
backporting to dead kernels"
* tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/of: Fix CPU devicetree-node lookups
x86/ioapic: Ignore IRQ2 again
x86: Introduce restart_block->arch_data to remove TS_COMPAT_RESTART
x86: Introduce TS_COMPAT_RESTART to fix get_nr_restart_syscall()
x86: Move TS_COMPAT back to asm/thread_info.h
kernel, fs: Introduce and use set_restart_fn() and arch_set_restart_data()
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2021-03-20
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 3 day(s) which contain
a total of 8 files changed, 155 insertions(+), 12 deletions(-).
The main changes are:
1) Use correct nops in fexit trampoline, from Stanislav.
2) Fix BTF dump, from Jean-Philippe.
3) Fix umd memory leak, from Zqiang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull io_uring fixes from Jens Axboe:
"Quieter week this time, which was both expected and desired. About
half of the below is fixes for this release, the other half are just
fixes in general. In detail:
- Fix the freezing of IO threads, by making the freezer not send them
fake signals. Make them freezable by default.
- Like we did for personalities, move the buffer IDR to xarray. Kills
some code and avoids a use-after-free on teardown.
- SQPOLL cleanups and fixes (Pavel)
- Fix linked timeout race (Pavel)
- Fix potential completion post use-after-free (Pavel)
- Cleanup and move internal structures outside of general kernel view
(Stefan)
- Use MSG_SIGNAL for send/recv from io_uring (Stefan)"
* tag 'io_uring-5.12-2021-03-19' of git://git.kernel.dk/linux-block:
io_uring: don't leak creds on SQO attach error
io_uring: use typesafe pointers in io_uring_task
io_uring: remove structures from include/linux/io_uring.h
io_uring: imply MSG_NOSIGNAL for send[msg]()/recv[msg]() calls
io_uring: fix sqpoll cancellation via task_work
io_uring: add generic callback_head helpers
io_uring: fix concurrent parking
io_uring: halt SQO submission on ctx exit
io_uring: replace sqd rw_semaphore with mutex
io_uring: fix complete_post use ctx after free
io_uring: fix ->flags races by linked timeouts
io_uring: convert io_buffer_idr to XArray
io_uring: allow IO worker threads to be frozen
kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing
|
|
The syzbot reported a memleak as follows:
BUG: memory leak
unreferenced object 0xffff888101b41d00 (size 120):
comm "kworker/u4:0", pid 8, jiffies 4294944270 (age 12.780s)
backtrace:
[<ffffffff8125dc56>] alloc_pid+0x66/0x560
[<ffffffff81226405>] copy_process+0x1465/0x25e0
[<ffffffff81227943>] kernel_clone+0xf3/0x670
[<ffffffff812281a1>] kernel_thread+0x61/0x80
[<ffffffff81253464>] call_usermodehelper_exec_work
[<ffffffff81253464>] call_usermodehelper_exec_work+0xc4/0x120
[<ffffffff812591c9>] process_one_work+0x2c9/0x600
[<ffffffff81259ab9>] worker_thread+0x59/0x5d0
[<ffffffff812611c8>] kthread+0x178/0x1b0
[<ffffffff8100227f>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff888110ef5c00 (size 232):
comm "kworker/u4:0", pid 8414, jiffies 4294944270 (age 12.780s)
backtrace:
[<ffffffff8154a0cf>] kmem_cache_zalloc
[<ffffffff8154a0cf>] __alloc_file+0x1f/0xf0
[<ffffffff8154a809>] alloc_empty_file+0x69/0x120
[<ffffffff8154a8f3>] alloc_file+0x33/0x1b0
[<ffffffff8154ab22>] alloc_file_pseudo+0xb2/0x140
[<ffffffff81559218>] create_pipe_files+0x138/0x2e0
[<ffffffff8126c793>] umd_setup+0x33/0x220
[<ffffffff81253574>] call_usermodehelper_exec_async+0xb4/0x1b0
[<ffffffff8100227f>] ret_from_fork+0x1f/0x30
After the UMD process exits, the pipe_to_umh/pipe_from_umh and
tgid need to be released.
Fixes: d71fa5c9763c ("bpf: Add kernel module with user mode driver that populates bpffs.")
Reported-by: syzbot+44908bb56d2bfe56b28e@syzkaller.appspotmail.com
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210317030915.2865-1-qiang.zhang@windriver.com
|
|
s/recalcultion/recalculation/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull workqueue tracing fix from Steven Rostedt:
"Fix workqueue trace event unsafe string reference
After adding a verifier to test all strings printed in trace events to
make sure they either point to a string on the ring buffer, or to read
only core kernel memory, it triggered on a workqueue trace event. The
trace event workqueue_queue_work references the allocated name of the
workqueue in the output. If the workqueue is freed before the trace is
read, then the trace will dereference freed memory.
Update the trace event to use the __string(), __assign_str(), and
__get_str() helpers to handle such cases"
* tag 'trace-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
workqueue/tracing: Copy workqueue name to buffer in trace event
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/urgent
Pull EFI fixes from Ard Biesheuvel:
"- another missing RT_PROP table related fix, to ensure that the efivarfs
pseudo filesystem fails gracefully if variable services are unsupported
- use the correct alignment for literal EFI GUIDs
- fix a use after unmap issue in the memreserve code"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The current DEFINE_WW_MUTEX() macro fails to properly set up the lockdep
key of the ww_mutexes causing potential circular locking dependency
splat. Though it is possible to add more macro magic to make it work,
but the result is rather ugly.
Since locktorture was the only user of DEFINE_WW_MUTEX() and the
previous commit has just removed its use. It is easier to just remove
the macro to force future users of ww_mutexes to use ww_mutex_init()
for initialization.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210318172814.4400-4-longman@redhat.com
|
|
We are applying further, lower-prio fixes on top of two ww_mutex fixes in locking/urgent.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 494c704f9af0 ("efi: Use 32-bit alignment for efi_guid_t") updated
the type definition of efi_guid_t to ensure that it always appears
sufficiently aligned (the UEFI spec is ambiguous about this, but given
the fact that its EFI_GUID type is defined in terms of a struct carrying
a uint32_t, the natural alignment is definitely >= 32 bits).
However, we missed the EFI_GUID() macro which is used to instantiate
efi_guid_t literals: that macro is still based on the guid_t type,
which does not have a minimum alignment at all. This results in warnings
such as
In file included from drivers/firmware/efi/mokvar-table.c:35:
include/linux/efi.h:1093:34: warning: passing 1-byte aligned argument to
4-byte aligned parameter 2 of 'get_var' may result in an unaligned pointer
access [-Walign-mismatch]
status = get_var(L"SecureBoot", &EFI_GLOBAL_VARIABLE_GUID, NULL, &size,
^
include/linux/efi.h:1101:24: warning: passing 1-byte aligned argument to
4-byte aligned parameter 2 of 'get_var' may result in an unaligned pointer
access [-Walign-mismatch]
get_var(L"SetupMode", &EFI_GLOBAL_VARIABLE_GUID, NULL, &size, &setupmode);
The distinction only matters on CPUs that do not support misaligned loads
fully, but 32-bit ARM's load-multiple instructions fall into that category,
and these are likely to be emitted by the compiler that built the firmware
for loading word-aligned 128-bit GUIDs from memory
So re-implement the initializer in terms of our own efi_guid_t type, so that
the alignment becomes a property of the literal's type.
Fixes: 494c704f9af0 ("efi: Use 32-bit alignment for efi_guid_t")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/1327
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Several patches to testore use of memory barriers instead of RCU to
ensure consistent access to ruleset, from Mark Tomlinson.
2) Fix dump of expectation via ctnetlink, from Florian Westphal.
3) GRE helper works for IPv6, from Ludovic Senecaux.
4) Set error on unsupported flowtable flags.
5) Use delayed instead of deferrable workqueue in the flowtable,
from Yinjun Zhang.
6) Fix spurious EEXIST in case of add-after-delete flowtable in
the same batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes pull, pretty small set of fixes, a couple of i915 and
amdgpu, one ttm, one nouveau and one omap. Probably smaller than usual
for this time, so we'll see if something pops up next week or if this
will continue to stay small.
Summary:
ttm:
- Make ttm_bo_unpin() not wraparound on too many unpins
omap:
- Fix coccicheck warning in omap
amdgpu:
- DCN 3.0 gamma fixes
- DCN 2.1 corrupt screen fix
i915:
- Workaround async flip + VT-d frame corruption on HSW/BDW
- Fix NMI watchdog crash due to uninitialized OA buffer use on gen12+
nouveau:
- workaround oops with bo syncing"
* tag 'drm-fixes-2021-03-19' of git://anongit.freedesktop.org/drm/drm:
nouveau: Skip unvailable ttm page entries
drm/amd/display: Remove MPC gamut remap logic for DCN30
drm/amd/display: Correct algorithm for reversed gamma
drm/omap: dsi: fix unsigned expression compared with zero
i915/perf: Start hrtimer only if sampling the OA buffer
drm/i915: Workaround async flip + VT-d corruption on HSW/BDW
drm/amd/display: Copy over soc values before bounding box creation
drm/ttm: make ttm_bo_unpin more defensive
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.12-rc4:
- Make ttm_bo_unpin() not wraparound on too many unpins.
- Fix coccicheck warning in omap.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a0e13bbb-6ba6-ff24-4db8-0e02e605de18@linux.intel.com
|
|
Pull VFIO fixes from Alex Williamson:
- Fix 32-bit issue with new unmap-all flag (Steve Sistare)
- Various Kconfig changes for better coverage (Jason Gunthorpe)
- Fix to batch pinning support (Daniel Jordan)
* tag 'vfio-v5.12-rc4' of git://github.com/awilliam/linux-vfio:
vfio/type1: fix vaddr_get_pfns() return in vfio_pin_page_external()
vfio: Depend on MMU
ARM: amba: Allow some ARM_AMBA users to compile with COMPILE_TEST
vfio-platform: Add COMPILE_TEST to VFIO_PLATFORM
vfio: IOMMU_API should be selected
vfio/type1: fix unmap all on ILP32
|
|
Pull virtio fixes from Michael Tsirkin:
"Some fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: set v->config_ctx to NULL if eventfd_ctx_fdget() fails
vhost-vdpa: fix use-after-free of v->config_ctx
vhost: Fix vhost_vq_reset()
vhost_vdpa: fix the missing irq_bypass_unregister_producer() invocation
vdpa_sim: Skip typecasting from void*
virtio: remove export for virtio_config_{enable, disable}
virtio-mmio: Use to_virtio_mmio_device() to simply code
vdpa: set the virtqueue num during register
|
|
The trace event "workqueue_queue_work" references an unsafe string in
dereferencing the name of the workqueue. As the name is allocated, it
could later be freed, and the pointer to that string could stay on the
tracing buffer. If the trace buffer is read after the string is freed, it
will reference an unsafe pointer.
I added a new verifier to make sure that all strings referenced in the
output of the trace buffer is safe to read and this triggered on the
workqueue_queue_work trace event:
workqueue_queue_work: work struct=00000000b2b235c7 function=gc_worker workqueue=(0xffff888100051160:events_power_efficient)[UNSAFE-MEMORY] req_cpu=256 cpu=1
workqueue_queue_work: work struct=00000000c344caec function=flush_to_ldisc workqueue=(0xffff888100054d60:events_unbound)[UNSAFE-MEMORY] req_cpu=256 cpu=4294967295
workqueue_queue_work: work struct=00000000b2b235c7 function=gc_worker workqueue=(0xffff888100051160:events_power_efficient)[UNSAFE-MEMORY] req_cpu=256 cpu=1
workqueue_queue_work: work struct=000000000b238b3f function=vmstat_update workqueue=(0xffff8881000c3760:mm_percpu_wq)[UNSAFE-MEMORY] req_cpu=1 cpu=1
Also, if this event is read via a user space application like perf or
trace-cmd, the name would only be an address and useless information:
workqueue_queue_work: work struct=0xffff953f80b4b918 function=disk_events_workfn workqueue=ffff953f8005d378 req_cpu=8192 cpu=5
Cc: Zqiang <qiang.zhang@windriver.com>
Cc: Tejun Heo <tj@kernel.org>
Fixes: 7bf9c4a88e3e3 ("workqueue: tracing the name of the workqueue instead of it's address")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Clean up COMMAND_RECONFIG_FLAG_PARTIAL flag by resetting it to 0, which
aligns with the firmware settings.
Fixes: 36847f9e3e56 ("firmware: stratix10-svc: correct reconfig flag and timeout values")
Signed-off-by: Richard Gong <richard.gong@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
|
