| Age | Commit message (Collapse) | Author |
|---|
|
The Netronix embedded controller is a microcontroller found in some
e-book readers designed by the original design manufacturer Netronix,
Inc. It contains RTC, battery monitoring, system power management, and
PWM functionality.
This driver implements register access and version detection.
Third-party hardware documentation is available at:
https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller
The EC supports interrupts, but the driver doesn't make use of them so
far.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
ROHM BD9576 contains safety features like over/under voltage detection,
over curren detection and over temperature detection. Add the
configuration register information.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.
Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.
Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).
For above reason, do not consider missing IRQ as error.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add core support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In a system supporting MTE, the linear map must allow reading/writing
allocation tags by setting the memory type as Normal Tagged. Currently,
this is only handled for memory present at boot. Hotplugged memory uses
Normal non-Tagged memory.
Introduce pgprot_mhp() for hotplugged memory and use it in
add_memory_resource(). The arm64 code maps pgprot_mhp() to
pgprot_tagged().
Note that ZONE_DEVICE memory should not be mapped as Tagged and
therefore setting the memory type in arch_add_memory() is not feasible.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 0178dc761368 ("arm64: mte: Use Normal Tagged attributes for the linear map")
Reported-by: Patrick Daly <pdaly@codeaurora.org>
Tested-by: Patrick Daly <pdaly@codeaurora.org>
Link: https://lore.kernel.org/r/1614745263-27827-1-git-send-email-pdaly@codeaurora.org
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20210309122601.5543-1-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
seqcount_init() must be a macro in order to preserve the static
variable that is used for the lockdep key. Don't then wrap it in an
inline function, which destroys that.
Luckily there aren't many users of this function, but fix it before it
becomes a problem.
Fixes: 80793c3471d9 ("seqlock: Introduce seqcount_latch_t")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YEeFEbNUVkZaXDp4@hirez.programming.kicks-ass.net
|
|
Jakub reported that:
static struct net_device *rtl8139_init_board(struct pci_dev *pdev)
{
...
u64_stats_init(&tp->rx_stats.syncp);
u64_stats_init(&tp->tx_stats.syncp);
...
}
results in lockdep getting confused between the RX and TX stats lock.
This is because u64_stats_init() is an inline calling seqcount_init(),
which is a macro using a static variable to generate a lockdep class.
By wrapping that in an inline, we negate the effect of the macro and
fold the static key variable, hence the confusion.
Fix by also making u64_stats_init() a macro for the case where it
matters, leaving the other case an inline for argument validation
etc.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Debugged-by: "Ahmed S. Darwish" <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Erhard F." <erhard_f@mailbox.org>
Link: https://lkml.kernel.org/r/YEXicy6+9MksdLZh@hirez.programming.kicks-ass.net
|
|
i.MX21 support has been dropped, so remove such unused file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210304023220.2362407-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/c4d2e010ae2bf67cdfa0b55e6d1deb9339d9d3dc.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new function to convert bInterval into the time expressed
in 1us unit.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/25c8a09b055f716c1e5bf11fea72c3418f844482.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have 2 forward declarations of usb_bus_type, one in the system-wide
usb.h and the other in the "USB core only header file". This variable
is not exported from the USB core, so remove the declaration from usb.h
as it does not need to be there.
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20210226102356.716746-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apple SoCs are a distant descendant of Samsung designs and use yet
another variant of their UART style, with different interrupt handling.
In particular, this variant has the following differences with existing
ones:
* It includes a built-in interrupt controller with different registers,
using only a single platform IRQ
* Internal interrupt sources are treated as edge-triggered, even though
the IRQ output is level-triggered. This chiefly affects the TX IRQ
path: the driver can no longer rely on the TX buffer empty IRQ
immediately firing after TX is enabled, but instead must prime the
FIFO with data directly.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210304213902.83903-25-marcan@marcan.st
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that noone checks the return value, switch the return type of
tty_unregister_driver to void. We can do that as we always return zero.
Generally, drivers are not allowed to call tty_unregister_driver while
there are open devices.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-35-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is noone setting nci_uart_ops::recv_buf, so the default one
(nci_uart_default_recv_buf) is always used. So drop this hook, move
nci_uart_default_recv_buf before the use in nci_uart_tty_receive and
remove unused parameter flags.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
First, it is never checked. Second, use of it as a debugging aid is
at least questionable. With the current tools, I don't think anyone used
this kind of thing for debugging purposes for years.
On the top of that, e.g. serdev does not set this field of tty_ldisc_ops
at all.
So get rid of this legacy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While the driver is still marked as maintained in MAINTAINERS, Comtrol
does not really care about this ancient driver. They are still
manufacturing serial devices, but those are controlled only by
out-of-tree drivers.
Comtrol didn't answer my pings, so this driver is apparently
unmaintained. Aside from that, the driver was untouched for years, only
whole-tree changes happened during the past years. The driver needs much
more care, so drop it for now. If someone steps up to reintroduce it,
they need to clean it up first.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Isicom driver was orphaned by commit d86b3001a1a6 (MAINTAINERS:
orphan isicom) 10 years ago. Noone stepped up to take care of them and
to fix all the issues the driver has.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Cyclades driver was orphaned by commit d459883e6c54 (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.
On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The drivers were removed in a1f714b44e34 (tty: Remove redundant synclink
driver) and 3d608a591b2b (tty: Remove redundant synclinkmp driver).
So remove also the PCI ID entries.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
279dcf693ac7 ("virt: acrn: Introduce an interface for Service VM to
control vCPU") introduced {add,remove}_cpu() usage and it hit below
error with !CONFIG_SMP:
../drivers/virt/acrn/hsm.c: In function ‘remove_cpu_store’:
../drivers/virt/acrn/hsm.c:389:3: error: implicit declaration of function ‘remove_cpu’; [-Werror=implicit-function-declaration]
remove_cpu(cpu);
../drivers/virt/acrn/hsm.c:402:2: error: implicit declaration of function ‘add_cpu’; [-Werror=implicit-function-declaration]
add_cpu(cpu);
Add add_cpu() function prototypes with !CONFIG_SMP and remove_cpu() with
!CONFIG_HOTPLUG_CPU for such usage.
Fixes: 279dcf693ac7 ("virt: acrn: Introduce an interface for Service VM to control vCPU")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Qais Yousef <qais.yousef@arm.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Qais Yousef <qais.yousef@arm.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Shuo Liu <shuo.a.liu@intel.com>
Link: https://lore.kernel.org/r/20210221134339.57851-1-shuo.a.liu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to make it generic enough so other parts of the
kernel can also provide their own implementation of scale_freq_tick()
callback, which is called by the scheduler periodically to update the
per-cpu arch_freq_scale variable.
The implementations now need to provide 'struct scale_freq_data' for the
CPUs for which they have hardware counters available, and a callback
gets registered for each possible CPU in a per-cpu variable.
The arch specific (or ARM AMU) counters are updated to adapt to this and
they take the highest priority if they are available, i.e. they will be
used instead of CPPC based counters for example.
The special code to rebuild the sched domains, in case invariance status
change for the system, is moved out of arm64 specific code and is added
to arch_topology.c.
Note that this also defines SCALE_FREQ_SOURCE_CPUFREQ but doesn't use it
and it is added to show that cpufreq is also acts as source of
information for FIE and will be used by default if no other counters are
supported for a platform.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Tested-by: Ionela Voinescu <ionela.voinescu@arm.com>
Acked-by: Will Deacon <will@kernel.org> # for arm64
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Rename freq_scale to a less generic name, as it will get exported soon
for modules. Since x86 already names its own implementation of this as
arch_freq_scale, lets stick to that.
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add aldebaran in amdgpu_asic_name array and amdgpu_asic_type enum
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull networking fixes from David Miller:
1) Fix transmissions in dynamic SMPS mode in ath9k, from Felix Fietkau.
2) TX skb error handling fix in mt76 driver, also from Felix.
3) Fix BPF_FETCH atomic in x86 JIT, from Brendan Jackman.
4) Avoid double free of percpu pointers when freeing a cloned bpf prog.
From Cong Wang.
5) Use correct printf format for dma_addr_t in ath11k, from Geert
Uytterhoeven.
6) Fix resolve_btfids build with older toolchains, from Kun-Chuan
Hsieh.
7) Don't report truncated frames to mac80211 in mt76 driver, from
Lorenzop Bianconi.
8) Fix watcdog timeout on suspend/resume of stmmac, from Joakim Zhang.
9) mscc ocelot needs NET_DEVLINK selct in Kconfig, from Arnd Bergmann.
10) Fix sign comparison bug in TCP_ZEROCOPY_RECEIVE getsockopt(), from
Arjun Roy.
11) Ignore routes with deleted nexthop object in mlxsw, from Ido
Schimmel.
12) Need to undo tcp early demux lookup sometimes in nf_nat, from
Florian Westphal.
13) Fix gro aggregation for udp encaps with zero csum, from Daniel
Borkmann.
14) Make sure to always use imp*_ndo_send when necessaey, from Jason A.
Donenfeld.
15) Fix TRSCER masks in sh_eth driver from Sergey Shtylyov.
16) prevent overly huge skb allocationsd in qrtr, from Pavel Skripkin.
17) Prevent rx ring copnsumer index loss of sync in enetc, from Vladimir
Oltean.
18) Make sure textsearch copntrol block is large enough, from Wilem de
Bruijn.
19) Revert MAC changes to r8152 leading to instability, from Hates Wang.
20) Advance iov in 9p even for empty reads, from Jissheng Zhang.
21) Double hook unregister in nftables, from PabloNeira Ayuso.
22) Fix memleak in ixgbe, fropm Dinghao Liu.
23) Avoid dups in pkt scheduler class dumps, from Maximilian Heyne.
24) Various mptcp fixes from Florian Westphal, Paolo Abeni, and Geliang
Tang.
25) Fix DOI refcount bugs in cipso, from Paul Moore.
26) One too many irqsave in ibmvnic, from Junlin Yang.
27) Fix infinite loop with MPLS gso segmenting via virtio_net, from
Balazs Nemeth.
* git://git.kernel.org:/pub/scm/linux/kernel/git/netdev/net: (164 commits)
s390/qeth: fix notification for pending buffers during teardown
s390/qeth: schedule TX NAPI on QAOB completion
s390/qeth: improve completion of pending TX buffers
s390/qeth: fix memory leak after failed TX Buffer allocation
net: avoid infinite loop in mpls_gso_segment when mpls_hlen == 0
net: check if protocol extracted by virtio_net_hdr_set_proto is correct
net: dsa: xrs700x: check if partner is same as port in hsr join
net: lapbether: Remove netif_start_queue / netif_stop_queue
atm: idt77252: fix null-ptr-dereference
atm: uPD98402: fix incorrect allocation
atm: fix a typo in the struct description
net: qrtr: fix error return code of qrtr_sendmsg()
mptcp: fix length of ADD_ADDR with port sub-option
net: bonding: fix error return code of bond_neigh_init()
net: enetc: allow hardware timestamping on TX queues with tc-etf enabled
net: enetc: set MAC RX FIFO to recommended value
net: davicom: Use platform_get_irq_optional()
net: davicom: Fix regulator not turned off on driver removal
net: davicom: Fix regulator not turned off on failed probe
net: dsa: fix switchdev objects on bridge master mistakenly being applied on ports
...
|
|
For gso packets, virtio_net_hdr_set_proto sets the protocol (if it isn't
set) based on the type in the virtio net hdr, but the skb could contain
anything since it could come from packet_snd through a raw socket. If
there is a mismatch between what virtio_net_hdr_set_proto sets and
the actual protocol, then the skb could be handled incorrectly later
on.
An example where this poses an issue is with the subsequent call to
skb_flow_dissect_flow_keys_basic which relies on skb->protocol being set
correctly. A specially crafted packet could fool
skb_flow_dissect_flow_keys_basic preventing EINVAL to be returned.
Avoid blindly trusting the information provided by the virtio net header
by checking that the protocol in the packet actually matches the
protocol set by virtio_net_hdr_set_proto. Note that since the protocol
is only checked if skb->dev implements header_ops->parse_protocol,
packets from devices without the implementation are not checked at this
stage.
Fixes: 9274124f023b ("net: stricter validation of untrusted gso packets")
Signed-off-by: Balazs Nemeth <bnemeth@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For kuprobe and tracepoint bpf programs, kernel calls
trace_call_bpf() which calls BPF_PROG_RUN_ARRAY_CHECK()
to run the program array. Currently, BPF_PROG_RUN_ARRAY_CHECK()
also calls bpf_cgroup_storage_set() to set percpu
cgroup local storage with NULL value. This is
due to Commit 394e40a29788 ("bpf: extend bpf_prog_array to store
pointers to the cgroup storage") which modified
__BPF_PROG_RUN_ARRAY() to call bpf_cgroup_storage_set()
and this macro is also used by BPF_PROG_RUN_ARRAY_CHECK().
kuprobe and tracepoint programs are not allowed to call
bpf_get_local_storage() helper hence does not
access percpu cgroup local storage. Let us
change BPF_PROG_RUN_ARRAY_CHECK() not to
modify percpu cgroup local storage.
The issue is observed when I tried to debug [1] where
percpu data is overwritten due to
preempt_disable -> migration_disable
change. This patch does not completely fix the above issue,
which will be addressed separately, e.g., multiple cgroup
prog runs may preempt each other. But it does fix
any potential issue caused by tracing program
overwriting percpu cgroup storage:
- in a busy system, a tracing program is to run between
bpf_cgroup_storage_set() and the cgroup prog run.
- a kprobe program is triggered by a helper in cgroup prog
before bpf_get_local_storage() is called.
[1] https://lore.kernel.org/bpf/CAKH8qBuXCfUz=w8L+Fj74OaUpbosO29niYwTki7e3Ag044_aww@mail.gmail.com/T
Fixes: 394e40a29788 ("bpf: extend bpf_prog_array to store pointers to the cgroup storage")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Roman Gushchin <guro@fb.com>
Link: https://lore.kernel.org/bpf/20210309185028.3763817-1-yhs@fb.com
|
|
Add pinctrl macros for AM64 SoC. These macro definitions are similar to
that of previous platforms, but adding new definitions to avoid any
naming confusions in the soc dts files.
Unlike what checkpatch insists, we do not need parentheses enclosing
the values for this macro as we do intend it to generate two separate
values as has been done for other similar platforms.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210226144257.5470-3-d-gerlach@ti.com
|
|
Fix build error when CONFIG_POWER_SUPPLY is not enabled.
The build error occurs in mips (cavium_octeon_defconfig).
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_remove':
drivers/usb/dwc3/core.c:1657: undefined reference to `power_supply_put'
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_get_properties':
drivers/usb/dwc3/core.c:1270: undefined reference to `power_supply_get_by_name'
mips-linux-gnu-ld: drivers/usb/dwc3/core.o: in function `dwc3_probe':
drivers/usb/dwc3/core.c:1632: undefined reference to `power_supply_put'
Fixes: 59fa3def35de ("usb: dwc3: add a power supply for current control")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Ray Chi <raychi@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Document all of the DRM_CAP_* defines.
v2 (Pekka):
- Describe what the bit depth is
- Expand on preferred dumb buffer memory access patterns
- Explain what a PRIME buffer is
- Mention DRM_IOCTL_PRIME_FD_TO_HANDLE and DRM_IOCTL_PRIME_HANDLE_TO_FD
- Explicitly reference CLOCK_REALTIME and CLOCK_MONOTONIC
- Make it clear DRM_CAP_CRTC_IN_VBLANK_EVENT applies to both DRM_EVENT_VBLANK
and DRM_EVENT_FLIP_COMPLETE
v3 (Daniel):
- Specify kernel versions for caps that don't depend on drivers
- Make it clear dumb buffers caps are only about dumb buffers
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210308123421.747836-1-contact@emersion.fr
|
|
Currently the default behavior is to manually having the devfreq
backend to register themselves as a devfreq cooling device.
Instead of adding the code in the drivers for the thermal cooling
device registering, let's provide a flag in the devfreq's profile to
tell the common devfreq code to register the newly created devfreq as
a cooling device.
Suggested-by: Chanwoo Choi <cwchoi00@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
phy_data means private PHY data not date
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds missing license and/or copyright headers for KCSAN source files.
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The mem_dump_obj() functionality adds a few hundred bytes, which is a
small price to pay. Except on kernels built with CONFIG_PRINTK=n, in
which mem_dump_obj() messages will be suppressed. This commit therefore
makes mem_dump_obj() be a static inline empty function on kernels built
with CONFIG_PRINTK=n and excludes all of its support functions as well.
This avoids kernel bloat on systems that cannot use mem_dump_obj().
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <linux-mm@kvack.org>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
After commit 5130b8fd0690 ("rcu: Introduce kfree_rcu() single-argument macro"),
kernel-doc now emits two warnings:
./include/linux/rcupdate.h:884: warning: Excess function parameter 'ptr' description in 'kfree_rcu'
./include/linux/rcupdate.h:884: warning: Excess function parameter 'rhf' description in 'kfree_rcu'
This commit added some macro magic in order to call two different versions
of kfree_rcu(), the first having just one argument and the second having
two arguments. That makes it difficult to document the kfree_rcu() arguments
in the docboook header.
In order to make clearer that this macro accepts optional arguments,
this commit uses macro concatenation so that this macro changes from:
#define kfree_rcu kvfree_rcu
to:
#define kfree_rcu(ptr, rhf...) kvfree_rcu(ptr, ## rhf)
That not only helps kernel-doc understand the macro arguments, but also
provides a better C definition that makes clearer that the first argument
is mandatory and the second one is optional.
Fixes: 5130b8fd0690 ("rcu: Introduce kfree_rcu() single-argument macro")
Tested-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The hlist_nulls_for_each_entry_rcu() docbook header references the
atomic_ops.rst file, which was removed in commit f0400a77ebdc ("atomic:
Delete obsolete documentation"). This commit therefore substitutes a
section in memory-barriers.txt discussing the use of barrier() in loops.
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
The FIB lookup example[1] show how the IP-header field tot_len
(iph->tot_len) is used as input to perform the MTU check.
This patch extend the BPF-helper bpf_check_mtu() with the same ability
to provide the length as user parameter input, via mtu_len parameter.
This still needs to be done before the bpf_check_mtu() helper API
becomes frozen.
[1] samples/bpf/xdp_fwd_kern.c
Fixes: 34b2021cc616 ("bpf: Add BPF-helper for MTU checking")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161521555850.3515614.6533850861569774444.stgit@firesoul
|
|
There's no need to keep around a dentry pointer to a simple file that
debugfs itself can look up when we need to remove it from the system.
So simplify the code by deleting the variable and cleaning up the logic
around the debugfs file.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/YCvYV53ZdzQSWY6w@kroah.com
|
|
The functions defined in "arch/powerpc/kexec/ima.c" handle setting up
and freeing the resources required to carry over the IMA measurement
list from the current kernel to the next kernel across kexec system call.
These functions do not have architecture specific code, but are
currently limited to powerpc.
Move remove_ima_buffer() and setup_ima_buffer() calls into
of_kexec_alloc_and_setup_fdt() defined in "drivers/of/kexec.c".
Move the remaining architecture independent functions from
"arch/powerpc/kexec/ima.c" to "drivers/of/kexec.c".
Delete "arch/powerpc/kexec/ima.c" and "arch/powerpc/include/asm/ima.h".
Remove references to the deleted files and functions in powerpc and
in ima.
Co-developed-by: Prakhar Srivastava <prsriva@linux.microsoft.com>
Signed-off-by: Prakhar Srivastava <prsriva@linux.microsoft.com>
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Tested-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210221174930.27324-11-nramas@linux.microsoft.com
|
|
The fields ima_buffer_addr and ima_buffer_size in "struct kimage_arch"
for powerpc are used to carry forward the IMA measurement list across
kexec system call. These fields are not architecture specific, but are
currently limited to powerpc.
arch_ima_add_kexec_buffer() defined in "arch/powerpc/kexec/ima.c"
sets ima_buffer_addr and ima_buffer_size for the kexec system call.
This function does not have architecture specific code, but is
currently limited to powerpc.
Move ima_buffer_addr and ima_buffer_size to "struct kimage".
Set ima_buffer_addr and ima_buffer_size in ima_add_kexec_buffer()
in security/integrity/ima/ima_kexec.c.
Co-developed-by: Prakhar Srivastava <prsriva@linux.microsoft.com>
Signed-off-by: Prakhar Srivastava <prsriva@linux.microsoft.com>
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Suggested-by: Will Deacon <will@kernel.org>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210221174930.27324-9-nramas@linux.microsoft.com
|
|
Both arm64 and powerpc do essentially the same FDT /chosen setup for
kexec. The differences are either omissions that arm64 should have
or additional properties that will be ignored. The setup code can be
combined and shared by both powerpc and arm64.
The differences relative to the arm64 version:
- If /chosen doesn't exist, it will be created (should never happen).
- Any old dtb and initrd reserved memory will be released.
- The new initrd and elfcorehdr are marked reserved.
- "linux,booted-from-kexec" is set.
The differences relative to the powerpc version:
- "kaslr-seed" and "rng-seed" may be set.
- "linux,elfcorehdr" is set.
- Any existing "linux,usable-memory-range" is removed.
Combine the code for setting up the /chosen node in the FDT and updating
the memory reservation for kexec, for powerpc and arm64, in
of_kexec_alloc_and_setup_fdt() and move it to "drivers/of/kexec.c".
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210221174930.27324-6-nramas@linux.microsoft.com
|
|
ELF related fields elf_headers, elf_headers_sz, and elf_load_addr are
defined in architecture specific 'struct kimage_arch' for x86, powerpc,
and arm64. The name of these fields are different in these
architectures that makes it hard to have a common code for setting up
the device tree for kexec system call.
Move the ELF fields to 'struct kimage' defined in include/linux/kexec.h
so common code can use it.
Suggested-by: Rob Herring <robh@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210221174930.27324-2-nramas@linux.microsoft.com
|
|
Quite a few users of ACPI objects want to log a warning message if
the evaluation fails which is a repeating pattern, so introduce a
helper function for that purpose and convert some code where it is
open-coded to using it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
STIMER0 interrupts are most naturally modeled as per-cpu IRQs. But
because x86/x64 doesn't have per-cpu IRQs, the core STIMER0 interrupt
handling machinery is done in code under arch/x86 and Linux IRQs are
not used. Adding support for ARM64 means adding equivalent code
using per-cpu IRQs under arch/arm64.
A better model is to treat per-cpu IRQs as the normal path (which it is
for modern architectures), and the x86/x64 path as the exception. Do this
by incorporating standard Linux per-cpu IRQ allocation into the main
SITMER0 driver code, and bypass it in the x86/x64 exception case. For
x86/x64, special case code is retained under arch/x86, but no STIMER0
interrupt handling code is needed under arch/arm64.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1614721102-2241-11-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
VMbus interrupts are most naturally modelled as per-cpu IRQs. But
because x86/x64 doesn't have per-cpu IRQs, the core VMbus interrupt
handling machinery is done in code under arch/x86 and Linux IRQs are
not used. Adding support for ARM64 means adding equivalent code
using per-cpu IRQs under arch/arm64.
A better model is to treat per-cpu IRQs as the normal path (which it is
for modern architectures), and the x86/x64 path as the exception. Do this
by incorporating standard Linux per-cpu IRQ allocation into the main VMbus
driver, and bypassing it in the x86/x64 exception case. For x86/x64,
special case code is retained under arch/x86, but no VMbus interrupt
handling code is needed under arch/arm64.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/1614721102-2241-7-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
With the new Hyper-V MSR set function, hyperv_report_panic_msg() can be
architecture neutral, so move it out from under arch/x86 and merge into
hv_kmsg_dump(). This move also avoids needing a separate implementation
under arch/arm64.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/1614721102-2241-5-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Current code defines a separate get and set macro for each Hyper-V
synthetic MSR used by the VMbus driver. Furthermore, the get macro
can't be converted to a standard function because the second argument
is modified in place, which is somewhat bad form.
Redo this by providing a single get and a single set function that
take a parameter specifying the MSR to be operated on. Fixup usage
of the get function. Calling locations are no more complex than before,
but the code under arch/x86 and the upcoming code under arch/arm64
is significantly simplified.
Also standardize the names of Hyper-V synthetic MSRs that are
architecture neutral. But keep the old x86-specific names as aliases
that can be removed later when all references (particularly in KVM
code) have been cleaned up in a separate patch series.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/1614721102-2241-4-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
The definition of enum hv_message_type includes arch neutral and
x86/x64-specific values. Ideally there would be a way to put the
arch neutral values in an arch neutral module, and the arch
specific values in an arch specific module. But C doesn't provide
a way to extend enum types. As a compromise, move the entire
definition into an arch neutral module, to avoid duplicating the
arch neutral values for x86/x64 and for ARM64.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/1614721102-2241-3-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
The Hyper-V page allocator functions are implemented in an architecture
neutral way. Move them into the architecture neutral VMbus module so
a separate implementation for ARM64 is not needed.
No functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/1614721102-2241-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Drop the definitions of the following symbols:
ACPI_SBS_COMPONENT
ACPI_FAN_COMPONENT
ACPI_CONTAINER_COMPONENT
ACPI_MEMORY_DEVICE_COMPONENT
that are not used in a meaningful way any more and update the ACPI
debug documentation to avoid confusing users by making the impression
that the ACPICA debug can be used for anything other than ACPICA
itself, which is incorrect.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
|
|
Replace the only ACPI_EXCEPTION() instance in sysfs.c with a
pr_warn() call, drop the _COMPONENT and ACPI_MODULE_NAME()
definitions that are not used any more and drop the
ACPI_SYSTEM_COMPONENT definition that would not be used any
more in a meaningful way after the above changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
|
