| Age | Commit message (Collapse) | Author |
|---|
|
The CRNG is faster, and we don't pretend to track entropy usage in the
CRNG any more.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Leonard Crestez observed the following phenomenon: when using
hard interrupt triggers (the DRDY line coming out of an ST
sensor) sometimes a new value would arrive while reading the
previous value, due to latencies in the system.
We discovered that the ST hardware as far as can be observed
is designed for level interrupts: the DRDY line will be held
asserted as long as there are new values coming. The interrupt
handler should be re-entered until we're out of values to
handle from the sensor.
If interrupts were handled as occurring on the edges (usually
low-to-high) new values could appear and the line be held
asserted after that, and these values would be missed, the
interrupt handler would also lock up as new data was
available, but as no new edges occurs on the DRDY signal,
nothing happens: the edge detector only detects edges.
To counter this, do the following:
- Accept interrupt lines to be flagged as level interrupts
using IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW. If the line
is marked like this (in the device tree node or ACPI
table or similar) it will be utilized as a level IRQ.
We mark the line with IRQF_ONESHOT and mask the IRQ
while processing a sample, then the top half will be
entered again if new values are available.
- If we are flagged as using edge interrupts with
IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING: remove
IRQF_ONESHOT so that the interrupt line is not
masked while running the thread part of the interrupt.
This way we will never miss an interrupt, then introduce
a loop that polls the data ready registers repeatedly
until no new samples are available, then exit the
interrupt handler. This way we know no new values are
available when the interrupt handler exits and
new (edge) interrupts will be triggered when data arrives.
Take some extra care to update the timestamp in the poll
loop if this happens. The timestamp will not be 100%
perfect, but it will at least be closer to the actual
events. Usually the extra poll loop will handle the new
samples, but once in a blue moon, we get a new IRQ
while exiting the loop, before returning from the
thread IRQ bottom half with IRQ_HANDLED. On these rare
occasions, the removal of IRQF_ONESHOT means the
interrupt will immediately fire again.
- If no interrupt type is indicated from the DT/ACPI,
choose IRQF_TRIGGER_RISING as default, as this is necessary
for legacy boards.
Tested successfully on the LIS331DL and L3G4200D by setting
sampling frequency to 400Hz/800Hz and stressing the system:
extra reads in the threaded interrupt handler occurs.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.
Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.
The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.
Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drm-next
The patchset contains a new helper in drm_fb_cma_helper.c for suspend/
resume when using cma backed framebuffers.
* 'for-next' of http://git.agner.ch/git/linux-drm-fsl-dcu:
drm/fsl-dcu: disable vblank events on CRTC disable
drm/fsl-dcu: implement suspend/resume using atomic helpers
drm/fsl-dcu: use clk helpers
drm/fsl-dcu: move layer initialization to plane file
drm/fsl-dcu: store layer registers in soc_data
drm/fb_cma_helper: add suspend helper
|
|
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
here's a batch of i915 fixes for 4.7.
* tag 'drm-intel-fixes-2016-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
|
|
adding suspend and resume funtionality for extcon-adc-jack
driver to configure system wake up for extcon events,
also adding support to enable/disable system wakeup
through flag wakeup_source based on platform requirement.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
On Freescale i.MX7D platform, all clocks operations, including
enable/disable, rate change and re-parent, requires its parent
clock enable. Current clock core can not support it well.
This patch introduce a new flag CLK_OPS_PARENT_ENABLE to handle this
special case in clock core that enable its parent clock firstly for
each operation and disable it later after operation complete.
The patch part 1 fixes the possible disabling clocks while its parent
is off during kernel booting phase in clk_disable_unused_subtree().
Before the completion of kernel booting, clock tree is still not built
completely, there may be a case that the child clock is on but its
parent is off which could be caused by either HW initial reset state
or bootloader initialization.
Taking bootloader as an example, we may enable all clocks in HW by default.
And during kernel booting time, the parent clock could be disabled in its
driver probe due to calling clk_prepare_enable and clk_disable_unprepare.
Because it's child clock is only enabled in HW while its SW usecount
in clock tree is still 0, so clk_disable of parent clock will gate
the parent clock in both HW and SW usecount ultimately. Then there will
be a child clock is still on in HW but its parent is already off.
Later in clk_disable_unused(), this clock disable accessing while its
parent off will cause system hang due to the limitation of HW which
must require its parent on.
This patch simply enables the parent clock first before disabling
if flag CLK_OPS_PARENT_ENABLE is set in clk_disable_unused_subtree().
This is a simple solution and only affects booting time.
After kernel booting up the clock tree is already created, there will
be no case that child is off but its parent is off.
So no need do this checking for normal clk_disable() later.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
Placeholder for the rk3399 watchdog pclk, some newly exported
rk3228 clockids and a small fix for the not yet used spdif to
displayport clock on the rk3399.
* tag 'v4.8-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix incorrect rk3399 spdif-DPTX divider bits
clk: rockchip: export rk3228 MAC clocks
clk: rockchip: rename rk3228 sclk_macphy_50m to sclk_mac_extclk
clk: rockchip: export rk3228 audio clocks
clk: rockchip: include rk3228 downstream muxes into fractional dividers
clk: rockchip: fix incorrect rk3228 clock registers
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
clk: rockchip: add a dummy clock for the watchdog pclk on rk3399
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
Pull tegra clk driver updates from Thierry Reding:
Fixes and enhancements mostly for Tegra210 clocks that allow DSI and
HDMI to work on Tegra X1. There's also a refactoring, including fixes,
the USB PLL.
* tag 'tegra-for-4.8-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Initialize UTMI PLL when enabling PLLU
clk: tegra: Micro-optimize Tegra210 clock setup
clk: tegra: Make sor_safe the parent of dpaux and dpaux1
clk: tegra: Mark timer clock as critical
clk: tegra: Enable sor1 and sor1_src on Tegra210
clk: tegra: Squash sor1 safe/brick/src into a single mux
clk: tegra: Disable spread spectrum on pll_d2
clk: tegra: Fixup post dividers on Tegra210
|
|
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c4f "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
power_supply_get_property() should ideally return -EAGAIN if it is
called while the power_supply is being registered. There was no way
previously to determine if use_cnt == 0 meant that the power_supply
wasn't fully registered yet, or if it had already been unregistered.
Add a new boolean to the power_supply struct to simply show if
registration is completed. Lastly, modify the check in
power_supply_show_property() to also ignore -EAGAIN when so it
doesn't complain about not returning the property.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4bf ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a BPF_MAP_TYPE_CGROUP_ARRAY and its bpf_map_ops's implementations.
To update an element, the caller is expected to obtain a cgroup2 backed
fd by open(cgroup2_dir) and then update the array with that fd.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper function to get a cgroup2 from a fd. It will be
stored in a bpf array (BPF_MAP_TYPE_CGROUP_ARRAY) which will
be introduced in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're always tracing IPv4 or IPv6 addresses, so we can save a lot
of space on the ringbuffer by allocating the correct sockaddr size.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Fixes: 83a712e0afef "sunrpc: add some tracepoints around ..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Similar to commit 9b368814b336 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jann Horn reported following analysis that could potentially result
in a very hard to trigger (if not impossible) UAF race, to quote his
event timeline:
- Set up a process with threads T1, T2 and T3
- Let T1 set up a socket filter F1 that invokes another filter F2
through a BPF map [tail call]
- Let T1 trigger the socket filter via a unix domain socket write,
don't wait for completion
- Let T2 call PERF_EVENT_IOC_SET_BPF with F2, don't wait for completion
- Now T2 should be behind bpf_prog_get(), but before bpf_prog_put()
- Let T3 close the file descriptor for F2, dropping the reference
count of F2 to 2
- At this point, T1 should have looked up F2 from the map, but not
finished executing it
- Let T3 remove F2 from the BPF map, dropping the reference count of
F2 to 1
- Now T2 should call bpf_prog_put() (wrong BPF program type), dropping
the reference count of F2 to 0 and scheduling bpf_prog_free_deferred()
via schedule_work()
- At this point, the BPF program could be freed
- BPF execution is still running in a freed BPF program
While at PERF_EVENT_IOC_SET_BPF time it's only guaranteed that the perf
event fd we're doing the syscall on doesn't disappear from underneath us
for whole syscall time, it may not be the case for the bpf fd used as
an argument only after we did the put. It needs to be a valid fd pointing
to a BPF program at the time of the call to make the bpf_prog_get() and
while T2 gets preempted, F2 must have dropped reference to 1 on the other
CPU. The fput() from the close() in T3 should also add additionally delay
to the reference drop via exit_task_work() when bpf_prog_release() gets
called as well as scheduling bpf_prog_free_deferred().
That said, it makes nevertheless sense to move the BPF prog destruction
generally after RCU grace period to guarantee that such scenario above,
but also others as recently fixed in ceb56070359b ("bpf, perf: delay release
of BPF prog after grace period") with regards to tail calls won't happen.
Integrating bpf_prog_free_deferred() directly into the RCU callback is
not allowed since the invocation might happen from either softirq or
process context, so we're not permitted to block. Reviewing all bpf_prog_put()
invocations from eBPF side (note, cBPF -> eBPF progs don't use this for
their destruction) with call_rcu() look good to me.
Since we don't know whether at the time of attaching the program, we're
already part of a tail call map, we need to use RCU variant. However, due
to this, there won't be severely more stress on the RCU callback queue:
situations with above bpf_prog_get() and bpf_prog_put() combo in practice
normally won't lead to releases, but even if they would, enough effort/
cycles have to be put into loading a BPF program into the kernel already.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are cases where it is desired to see if a proposed placement
is compatible with a buffer object before calling ttm_bo_validate().
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
---
This is the first of a 3-patch series to fix a black screen
issue observed on Ubuntu 16.04 server.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues"
* tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: don't free bandwidth_mutex too early
USB: EHCI: declare hostpc register as zero-length array
phy-sun4i-usb: Fix irq free conditions to match request conditions
phy: bcm-ns-usb2: checking the wrong variable
phy-sun4i-usb: fix missing __iomem *
phy: phy-sun4i-usb: Fix optional gpios failing probe
phy: rockchip-dp: fix return value check in rockchip_dp_phy_probe()
phy: rcar-gen3-usb2: fix unexpected repeat interrupts of VBUS change
usb: common: otg-fsm: add license to usb-otg-fsm
|
|
Every implementation of RSA that we have naturally generates
output with leading zeroes. The one and only user of RSA,
pkcs1pad wants to have those leading zeroes in place, in fact
because they are currently absent it has to write those zeroes
itself.
So we shouldn't be stripping leading zeroes in the first place.
In fact this patch makes rsa-generic produce output with fixed
length so that pkcs1pad does not need to do any extra work.
This patch also changes DH to use the new interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds the helper crypto_inst_setname because the current
helper crypto_alloc_instance2 is no longer useful given that we
now look up the algorithm after we allocate the instance object.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
We can use simpel utils asoc_simple_card_parse_daifmt().
Let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are code duplications of a masked ethernet address comparison here
so make it a separate function instead.
Miscellanea:
o Neaten alignment of FWINV macro uses to make it clearer for the reader
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pooled EU is a bxt only feature and kernel changes are already merged. This
feature is not yet exposed to userspace as the support was not yet
available. Beignet team expressed interest and added patches to use this.
Since we now have a user and patches to use them, expose them from the
kernel side as well.
v2: fix compile error
[1] https://lists.freedesktop.org/archives/beignet/2016-June/007698.html
[2] https://lists.freedesktop.org/archives/beignet/2016-June/007699.html
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Tim Gore <tim.gore@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467369782-25992-1-git-send-email-arun.siluvery@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get fw response.
Add delayed callback timeout work before posting the command to fw.
In case of real fw command completion we will cancel the delayed work.
In case of fw command timeout the callback timeout handler will be
called and it will simulate fw completion with timeout error.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.
KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c
Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.
Fixes: 815117adaf5b ("bonding: use ether_addr_equal_unaligned for bond addr compare")
Fixes: bb54e58929f3 ("bonding: Verify RX LACPDU has proper dest mac-addr")
Fixes: 885a136c52a8 ("bonding: use compare_ether_addr_64bits() in ALB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to queue tx packets in sk_receive_queue, this is less
efficient since it requires spinlocks to synchronize between producer
and consumer.
This patch tries to address this by:
- switch from sk_receive_queue to a skb_array, and resize it when
tx_queue_len was changed.
- introduce a new proto_ops peek_len which was used for peeking the
skb length.
- implement a tun version of peek_len for vhost_net to use and convert
vhost_net to use peek_len if possible.
Pktgen test shows about 15.3% improvement on guest receiving pps for small
buffers:
Before: ~1300000pps
After : ~1500000pps
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new event - NETDEV_CHANGE_TX_QUEUE_LEN, this
will be triggered when tx_queue_len. It could be used by net device
who want to do some processing at that time. An example is tun who may
want to resize tx array when tx_queue_len is changed.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes, we need support resizing multiple queues at once. This is
because it was not easy to recover to recover from a partial failure
of multiple queues resizing.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes, we need zero length ring. But current code will crash since
we don't do any check before accessing the ring. This patch fixes this.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the functions from context_tracking.h directly.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into work.misc
|
|
|
|
Update posix_acl_valid to verify that an acl is within a user namespace.
Update the callers of posix_acl_valid to pass in an appropriate
user namespace. For posix_acl_xattr_set and v9fs_xattr_set_acl pass in
inode->i_sb->s_user_ns to posix_acl_valid. For md_unpack_acl pass in
&init_user_ns as no inode or superblock is in sight.
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Refuse to admit any user namespace has a mapping of the INVALID_UID
and the INVALID_GID when !CONFIG_USER_NS.
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
* clk-hw-unregister-fixed-rate:
clk: fixed-rate: add clk_hw_unregister_fixed_rate()
|
|
This will be used to migrate to the clk_hw APIs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Chris Worley reports:
RIP: 0010:[<ffffffffa0245f80>] [<ffffffffa0245f80>] rpc_new_client+0x2a0/0x2e0 [sunrpc]
RSP: 0018:ffff880158f6f548 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880234f8bc00 RCX: 000000000000ea60
RDX: 0000000000074cc0 RSI: 000000000000ea60 RDI: ffff880234f8bcf0
RBP: ffff880158f6f588 R08: 000000000001ac80 R09: ffff880237003300
R10: ffff880201171000 R11: ffffea0000d75200 R12: ffffffffa03afc60
R13: ffff880230c18800 R14: 0000000000000000 R15: ffff880158f6f680
FS: 00007f0e32673740(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000234886000 CR4: 00000000001406e0
Stack:
ffffffffa047a680 0000000000000000 ffff880158f6f598 ffff880158f6f680
ffff880158f6f680 ffff880234d11d00 ffff88023357f800 ffff880158f6f7d0
ffff880158f6f5b8 ffffffffa024660a ffff880158f6f5b8 ffffffffa02492ec
Call Trace:
[<ffffffffa024660a>] rpc_create_xprt+0x1a/0xb0 [sunrpc]
[<ffffffffa02492ec>] ? xprt_create_transport+0x13c/0x240 [sunrpc]
[<ffffffffa0246766>] rpc_create+0xc6/0x1a0 [sunrpc]
[<ffffffffa038e695>] nfs_create_rpc_client+0xf5/0x140 [nfs]
[<ffffffffa038f31a>] nfs_init_client+0x3a/0xd0 [nfs]
[<ffffffffa038f22f>] nfs_get_client+0x25f/0x310 [nfs]
[<ffffffffa025cef8>] ? rpc_ntop+0xe8/0x100 [sunrpc]
[<ffffffffa047512c>] nfs3_set_ds_client+0xcc/0x100 [nfsv3]
[<ffffffffa041fa10>] nfs4_pnfs_ds_connect+0x120/0x400 [nfsv4]
[<ffffffffa03d41c7>] nfs4_ff_layout_prepare_ds+0xe7/0x330 [nfs_layout_flexfiles]
[<ffffffffa03d1b1b>] ff_layout_pg_init_write+0xcb/0x280 [nfs_layout_flexfiles]
[<ffffffffa03a14dc>] __nfs_pageio_add_request+0x12c/0x490 [nfs]
[<ffffffffa03a1fa2>] nfs_pageio_add_request+0xc2/0x2a0 [nfs]
[<ffffffffa03a0365>] ? nfs_pageio_init+0x75/0x120 [nfs]
[<ffffffffa03a5b50>] nfs_do_writepage+0x120/0x270 [nfs]
[<ffffffffa03a5d31>] nfs_writepage_locked+0x61/0xc0 [nfs]
[<ffffffff813d4115>] ? __percpu_counter_add+0x55/0x70
[<ffffffffa03a6a9f>] nfs_wb_single_page+0xef/0x1c0 [nfs]
[<ffffffff811ca4a3>] ? __dec_zone_page_state+0x33/0x40
[<ffffffffa0395b21>] nfs_launder_page+0x41/0x90 [nfs]
[<ffffffff811baba0>] invalidate_inode_pages2_range+0x340/0x3a0
[<ffffffff811bac17>] invalidate_inode_pages2+0x17/0x20
[<ffffffffa039960e>] nfs_release+0x9e/0xb0 [nfs]
[<ffffffffa0399570>] ? nfs_open+0x60/0x60 [nfs]
[<ffffffffa0394dad>] nfs_file_release+0x3d/0x60 [nfs]
[<ffffffff81226e6c>] __fput+0xdc/0x1e0
[<ffffffff81226fbe>] ____fput+0xe/0x10
[<ffffffff810bf2e4>] task_work_run+0xc4/0xe0
[<ffffffff810a4188>] do_exit+0x2e8/0xb30
[<ffffffff8102471c>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff811464e6>] ? __audit_syscall_exit+0x1e6/0x280
[<ffffffff810a4a5f>] do_group_exit+0x3f/0xa0
[<ffffffff810a4ad4>] SyS_exit_group+0x14/0x20
[<ffffffff8179b76e>] system_call_fastpath+0x12/0x71
Which seems to be due to a call to utsname() when in a task exit context
in order to determine the hostname to set in rpc_new_client().
In reality, what we want here is not the hostname of the current task, but
the hostname that was used to set up the metadata server.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
* clk-hi6220-rtc:
clk: hi6220: Add RTC clock for pl031
|
|
Adds clk support for the pl031 RTC on hi6220
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[jstultz: Forward ported, tweaked commit description]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: VMX instructions: fix segment checks when L1 is in long mode.
KVM: LAPIC: cap __delay at lapic_timer_advance_ns
KVM: x86: move nsec_to_cycles from x86.c to x86.h
pvclock: Get rid of __pvclock_read_cycles in function pvclock_read_flags
pvclock: Cleanup to remove function pvclock_get_nsec_offset
pvclock: Add CPU barriers to get correct version value
KVM: arm/arm64: Stop leaking vcpu pid references
arm64: KVM: fix build with CONFIG_ARM_PMU disabled
|
