| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit c510eff6beba ("fsnotify: destroy marks with
call_srcu instead of dedicated thread").
Eryu reported that he was seeing some OOM kills kick in when running a
testcase that adds and removes inotify marks on a file in a tight loop.
The above commit changed the code to use call_srcu to clean up the
marks. While that does (in principle) work, the srcu callback job is
limited to cleaning up entries in small batches and only once per jiffy.
It's easily possible to overwhelm that machinery with too many call_srcu
callbacks, and Eryu's reproduer did just that.
There's also another potential problem with using call_srcu here. While
you can obviously sleep while holding the srcu_read_lock, the callbacks
run under local_bh_disable, so you can't sleep there.
It's possible when putting the last reference to the fsnotify_mark that
we'll end up putting a chain of references including the fsnotify_group,
uid, and associated keys. While I don't see any obvious ways that that
could occurs, it's probably still best to avoid using call_srcu here
after all.
This patch reverts the above patch. A later patch will take a different
approach to eliminated the dedicated thread here.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reported-by: Eryu Guan <guaneryu@gmail.com>
Tested-by: Eryu Guan <guaneryu@gmail.com>
Cc: Jan Kara <jack@suse.com>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ilya reported following lockdep splat:
kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory
ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0: (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1: (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2: (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.
We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: ebb516af60e1 ("tcp/dccp: fix race at listener dismantle phase")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.
Fix this issue by checking and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Revert 811a4e6fce09 ("PCI: Add helpers to manage pci_dev->irq and
pci_dev->irq_managed").
This is part of reverting 991de2e59090 ("PCI, x86: Implement
pcibios_alloc_irq() and pcibios_free_irq()") to fix regressions it
introduced.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>
|
|
Remove the ftrace module notifier in favor of directly calling
ftrace_module_enable() and ftrace_release_mod() in the module loader.
Hard-coding the function calls directly in the module loader removes
dependence on the module notifier call chain and provides better
visibility and control over what gets called when, which is important
to kernel utilities such as livepatch.
This fixes a notifier ordering issue in which the ftrace module notifier
(and hence ftrace_module_enable()) for coming modules was being called
after klp_module_notify(), which caused livepatch modules to initialize
incorrectly. This patch removes dependence on the module notifier call
chain in favor of hard coding the corresponding function calls in the
module loader. This ensures that ftrace and livepatch code get called in
the correct order on patch module load and unload.
Fixes: 5156dca34a3e ("ftrace: Fix the race between ftrace and insmod")
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes from the past few weeks that should go into 4.5.
This contains:
- Overflow fix for sysfs discard show function from Alan.
- A stacking limit init fix for max_dev_sectors, so we don't end up
artificially capping some use cases. From Keith.
- Have blk-mq proper end unstarted requests on a dying queue, instead
of pushing that to the driver. From Keith.
- NVMe:
- Update to Kconfig description for NVME_SCSI, since it was
vague and having it on is important for some SUSE distros.
From Christoph.
- Set of fixes from Keith, around surprise removal. Also kills
the no-merge flag, so it supports merging.
- Set of fixes for lightnvm from Matias, Javier, and Wenwei.
- Fix null_blk oops when asked for lightnvm, but not available. From
Matias.
- Copy-to-user EINTR fix from Hannes, fixing a case where SG_IO fails
if interrupted by a signal.
- Two floppy fixes from Jiri, fixing signal handling and blocking
open.
- A use-after-free fix for O_DIRECT, from Mike Krinkin.
- A block module ref count fix from Roman Pen.
- An fs IO wait accounting fix for O_DSYNC from Stephane Gasparini.
- Smaller reallo fix for xen-blkfront from Bob Liu.
- Removal of an unused struct member in the deadline IO scheduler,
from Tahsin.
- Also from Tahsin, properly initialize inode struct members
associated with cgroup writeback, if enabled.
- From Tejun, ensure that we keep the superblock pinned during cgroup
writeback"
* 'for-linus' of git://git.kernel.dk/linux-block: (25 commits)
blk: fix overflow in queue_discard_max_hw_show
writeback: initialize inode members that track writeback history
writeback: keep superblock pinned during cgroup writeback association switches
bio: return EINTR if copying to user space got interrupted
NVMe: Rate limit nvme IO warnings
NVMe: Poll device while still active during remove
NVMe: Requeue requests on suspended queues
NVMe: Allow request merges
NVMe: Fix io incapable return values
blk-mq: End unstarted requests on dying queue
block: Initialize max_dev_sectors to 0
null_blk: oops when initializing without lightnvm
block: fix module reference leak on put_disk() call for cgroups throttle
nvme: fix Kconfig description for BLK_DEV_NVME_SCSI
kernel/fs: fix I/O wait not accounted for RW O_DSYNC
floppy: refactor open() flags handling
lightnvm: allow to force mm initialization
lightnvm: check overflow and correct mlc pairs
lightnvm: fix request intersection locking in rrpc
lightnvm: warn if irqs are disabled in lock laddr
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This includes two fixes.
The first is something that has come up a few times and has been
worked out individually, but it's come up now enough that the problem
should be generic. Tracepoints are protected by RCU sched. There are
several tracepoints within core infrastructure like kfree(). If a
tracepoint is called when the CPU is going down, or when it's coming
up but has yet to be recognized by RCU, a RCU warning is triggered.
This is a true bug as that tracepoint is not protected by RCU.
Usually, this is taken care of by testing for cpu online as a
tracepoint condition. But as this is happening more often, moving it
from a individual tracepoint to a check in the tracepoint
infrastructure is more robust.
Note, there is now a duplicate of a cpu online test, because this
update does not remove the individual checks. But the overhead is
small enough that the removal can be done in another release.
The second change is strange linker breakage due to the branch
tracer's builtin_constant_p() check failing, and treating the
condition as a variable instead of a constant. Arnd Bergmann found
that this can be fixed by testing !!(cond) instead of just (cond)"
* tag 'trace-fixes-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix freak link error caused by branch tracer
tracepoints: Do not trace when cpu is offline
|
|
unreferenced object 0xffffc90000abf000 (size 16900):
comm "fsync02", pid 15765, jiffies 4297431627 (age 423.772s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 a0 c2 19 00 88 ff ff ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8174d54e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811b9b91>] __vmalloc_node_range+0x231/0x280
[<ffffffff811b9c2a>] __vmalloc+0x4a/0x50
[<ffffffffa02c9ec1>] ext_tree_prepare_commit+0x231/0x2e0 [blocklayoutdriver]
[<ffffffffa02c700e>] bl_prepare_layoutcommit+0xe/0x10 [blocklayoutdriver]
[<ffffffffa0596a6c>] pnfs_layoutcommit_inode+0x29c/0x330 [nfsv4]
[<ffffffffa0596b13>] pnfs_generic_sync+0x13/0x20 [nfsv4]
[<ffffffffa0585188>] nfs4_file_fsync+0x58/0x150 [nfsv4]
[<ffffffff81228e5b>] vfs_fsync_range+0x4b/0xb0
[<ffffffff81228f1d>] do_fsync+0x3d/0x70
[<ffffffff812291d0>] SyS_fsync+0x10/0x20
[<ffffffff81757def>] entry_SYSCALL_64_fastpath+0x12/0x76
[<ffffffffffffffff>] 0xffffffffffffffff
v2, add missing include header
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_0[0x1];
u8 srq_receive[0x1];
u8 reserved_1[0x1a];
};
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
struct mlx5_ifc_odp_per_transport_service_cap_bits {
u8 send[0x1];
u8 receive[0x1];
u8 write[0x1];
u8 read[0x1];
u8 reserved_at_4[0x1];
u8 srq_receive[0x1];
u8 reserved_at_6[0x1a];
};
This makes the conflicts much more rare and preserves the locality of
changes.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull IOMMU SVM fixes from David Woodhouse:
"Minor register size and interrupt acknowledgement fixes which only
showed up in testing on newer hardware, but mostly a fix to the MM
refcount handling to prevent a recursive refcount issue when mmap() is
used on the file descriptor associated with a bound PASID"
* tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu:
iommu/vt-d: Clear PPR bit to ensure we get more page request interrupts
iommu/vt-d: Fix 64-bit accesses to 32-bit DMAR_GSTS_REG
iommu/vt-d: Fix mm refcounting to hold mm_count not mm_users
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Prevent accidental deletion of EFI variables through efivarfs that
may brick machines. We use a whitelist of known-safe variables to
allow things like installing distributions to work out of the box, and
instead restrict vendor-specific variable deletion by making
non-whitelist variables immutable (Peter Jones)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Defining it as a connector was a bad idea. Remove it while it is
not too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Each function range is quite narrow and especially for connectors this
will pose a problem. Increase the function ranges while we still can and
move the connector range to the end so that range is practically limitless.
[mchehab@osg.samsung.com: Rebased to apply at Linus tree]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In my randconfig tests, I came across a bug that involves several
components:
* gcc-4.9 through at least 5.3
* CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files
* CONFIG_PROFILE_ALL_BRANCHES overriding every if()
* The optimized implementation of do_div() that tries to
replace a library call with an division by multiplication
* code in drivers/media/dvb-frontends/zl10353.c doing
u32 adc_clock = 450560; /* 45.056 MHz */
if (state->config.adc_clock)
adc_clock = state->config.adc_clock;
do_div(value, adc_clock);
In this case, gcc fails to determine whether the divisor
in do_div() is __builtin_constant_p(). In particular, it
concludes that __builtin_constant_p(adc_clock) is false, while
__builtin_constant_p(!!adc_clock) is true.
That in turn throws off the logic in do_div() that also uses
__builtin_constant_p(), and instead of picking either the
constant- optimized division, and the code in ilog2() that uses
__builtin_constant_p() to figure out whether it knows the answer at
compile time. The result is a link error from failing to find
multiple symbols that should never have been called based on
the __builtin_constant_p():
dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN'
dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod'
ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined!
ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined!
This patch avoids the problem by changing __trace_if() to check
whether the condition is known at compile-time to be nonzero, rather
than checking whether it is actually a constant.
I see this one link error in roughly one out of 1600 randconfig builds
on ARM, and the patch fixes all known instances.
Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.de
Acked-by: Nicolas Pitre <nico@linaro.org>
Fixes: ab3c9c686e22 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y")
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The tracepoint infrastructure uses RCU sched protection to enable and
disable tracepoints safely. There are some instances where tracepoints are
used in infrastructure code (like kfree()) that get called after a CPU is
going offline, and perhaps when it is coming back online but hasn't been
registered yet.
This can probuce the following warning:
[ INFO: suspicious RCU usage. ]
4.4.0-00006-g0fe53e8-dirty #34 Tainted: G S
-------------------------------
include/trace/events/kmem.h:141 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU! rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/8/0.
stack backtrace:
CPU: 8 PID: 0 Comm: swapper/8 Tainted: G S 4.4.0-00006-g0fe53e8-dirty #34
Call Trace:
[c0000005b76c78d0] [c0000000008b9540] .dump_stack+0x98/0xd4 (unreliable)
[c0000005b76c7950] [c00000000010c898] .lockdep_rcu_suspicious+0x108/0x170
[c0000005b76c79e0] [c00000000029adc0] .kfree+0x390/0x440
[c0000005b76c7a80] [c000000000055f74] .destroy_context+0x44/0x100
[c0000005b76c7b00] [c0000000000934a0] .__mmdrop+0x60/0x150
[c0000005b76c7b90] [c0000000000e3ff0] .idle_task_exit+0x130/0x140
[c0000005b76c7c20] [c000000000075804] .pseries_mach_cpu_die+0x64/0x310
[c0000005b76c7cd0] [c000000000043e7c] .cpu_die+0x3c/0x60
[c0000005b76c7d40] [c0000000000188d8] .arch_cpu_idle_dead+0x28/0x40
[c0000005b76c7db0] [c000000000101e6c] .cpu_startup_entry+0x50c/0x560
[c0000005b76c7ed0] [c000000000043bd8] .start_secondary+0x328/0x360
[c0000005b76c7f90] [c000000000008a6c] start_secondary_prolog+0x10/0x14
This warning is not a false positive either. RCU is not protecting code that
is being executed while the CPU is offline.
Instead of playing "whack-a-mole(TM)" and adding conditional statements to
the tracepoints we find that are used in this instance, simply add a
cpu_online() test to the tracepoint code where the tracepoint will be
ignored if the CPU is offline.
Use of raw_smp_processor_id() is fine, as there should never be a case where
the tracepoint code goes from running on a CPU that is online and suddenly
gets migrated to a CPU that is offline.
Link: http://lkml.kernel.org/r/1455387773-4245-1-git-send-email-kda@linux-powerpc.org
Reported-by: Denis Kirjanov <kda@linux-powerpc.org>
Fixes: 97e1c18e8d17b ("tracing: Kernel Tracepoints")
Cc: stable@vger.kernel.org # v2.6.28+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
According to the VT-d specification we need to clear the PPR bit in
the Page Request Status register when handling page requests, or the
hardware won't generate any more interrupts.
This wasn't actually necessary on SKL/KBL (which may well be the
subject of a hardware erratum, although it's harmless enough). But
other implementations do appear to get it right, and we only ever get
one interrupt unless we clear the PPR bit.
Reported-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
|
|
With ppc64 we use the deposited pgtable_t to store the hash pte slot
information. We should not withdraw the deposited pgtable_t without
marking the pmd none. This ensure that low level hash fault handling
will skip this huge pte and we will handle them at upper levels.
Recent change to pmd splitting changed the above in order to handle the
race between pmd split and exit_mmap. The race is explained below.
Consider following race:
CPU0 CPU1
shrink_page_list()
add_to_swap()
split_huge_page_to_list()
__split_huge_pmd_locked()
pmdp_huge_clear_flush_notify()
// pmd_none() == true
exit_mmap()
unmap_vmas()
zap_pmd_range()
// no action on pmd since pmd_none() == true
pmd_populate()
As result the THP will not be freed. The leak is detected by check_mm():
BUG: Bad rss-counter state mm:ffff880058d2e580 idx:1 val:512
The above required us to not mark pmd none during a pmd split.
The fix for ppc is to clear the huge pte of _PAGE_USER, so that low
level fault handling code skip this pte. At higher level we do take ptl
lock. That should serialze us against the pmd split. Once the lock is
acquired we do check the pmd again using pmd_same. That should always
return false for us and hence we should retry the access. We do the
pmd_same check in all case after taking plt with
THP (do_huge_pmd_wp_page, do_huge_pmd_numa_page and
huge_pmd_set_accessed)
Also make sure we wait for irq disable section in other cpus to finish
before flipping a huge pte entry with a regular pmd entry. Code paths
like find_linux_pte_or_hugepte depend on irq disable to get
a stable pte_t pointer. A parallel thp split need to make sure we
don't convert a pmd pte to a regular pmd entry without waiting for the
irq disable section to finish.
Fixes: eef1b3ba053a ("thp: implement split_huge_pmd()")
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 4.5-rc4
that resolve some reported issues.
One of them got reverted as it wasn't correct based on testing, and
all have been in linux-next for a while"
* tag 'tty-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "8250: uniphier: allow modular build with 8250 console"
pty: make sure super_block is still valid in final /dev/tty close
pty: fix possible use after free of tty->driver_data
tty: Add support for PCIe WCH382 2S multi-IO card
serial/omap: mark wait_for_xmitr as __maybe_unused
serial: omap: Prevent DoS using unprivileged ioctl(TIOCSRS485)
8250: uniphier: allow modular build with 8250 console
tty: Drop krefs for interrupted tty lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix preventing a 32bit overflow in timespec/val to cputime
conversions on 32bit machines"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the long awaited series to address a set of bugs around
active I/O remote-port LUN_RESET, as well as properly handling this
same case with concurrent fabric driver session disconnect ->
reconnect.
Note this set of LUN_RESET bug-fixes has been surviving extended
testing on both v4.5-rc1 and v3.14.y code over the last weeks, and is
CC'ed for stable as it's something folks using multiple ESX connected
hosts with slow backends can certainly trigger.
The highlights also include:
- Fix WRITE_SAME/DISCARD emulation 4k sector conversion in
target/iblock (Mike Christie)
- Fix TMR abort interaction and AIO type TMR response in qla2xxx
target (Quinn Tran + Swapnil Nagle)
- Fix >= v3.17 stale descriptor pointer regression in qla2xxx target
(Quinn Tran)
- Fix >= v4.5-rc1 return regression with unmap_zeros_data_store new
configfs store handler (nab)
- Add CPU affinity flag + convert qla2xxx to use bit (Quinn + HCH +
Bart)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: use TARGET_SCF_USE_CPUID flag to indiate CPU Affinity
target/transport: add flag to indicate CPU Affinity is observed
target: Fix incorrect unmap_zeroes_data_store return
qla2xxx: Use ATIO type to send correct tmr response
qla2xxx: Fix stale pointer access.
target/user: Fix cast from pointer to phys_addr_t
target: Drop legacy se_cmd->task_stop_comp + REQUEST_STOP usage
target: Fix race with SCF_SEND_DELAYED_TAS handling
target: Fix remote-port TMR ABORT + se_cmd fabric stop
target: Fix TAS handling for multi-session se_node_acls
target: Fix LUN_RESET active TMR descriptor handling
target: Fix LUN_RESET active I/O handling for ACK_KREF
qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM
qla2xxx: Fix warning reported by static checker
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
|
|
Merge fixes from Andrew Morton:
"10 fixes"
The lockdep hlist conversion is in the locking tree too, waiting for the
next merge window. Andrew thought it should go in now. I'll take it,
since it fixes a real problem and looks trivially correct (famous last
words).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/x86/Kconfig: CONFIG_X86_UV should depend on CONFIG_EFI
mm: fix pfn_t vs highmem
kernel/locking/lockdep.c: convert hash tables to hlists
mm,thp: fix spellos in describing __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
mm,thp: khugepaged: call pte flush at the time of collapse
mm/backing-dev.c: fix error path in wb_init()
mm, dax: check for pmd_none() after split_huge_pmd()
vsprintf: kptr_restrict is okay in IRQ when 2
mm: fix filemap.c kernel doc warning
ubsan: cosmetic fix to Kconfig text
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of seven fixes:
Two regressions in the new hisi_sas arm driver, a blacklist entry for
the marvell console which was causing a reset cascade without it, a
race fix in the WRITE_SAME/DISCARD routines, a retry fix for the rdac
driver, without which, it would prematurely return EIO and a couple of
fixes for the hyper-v storvsc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
block/sd: Return -EREMOTEIO when WRITE SAME and DISCARD are disabled
SCSI: Add Marvell Console to VPD blacklist
scsi_dh_rdac: always retry MODE SELECT on command lock violation
storvsc: Use the specified target ID in device lookup
storvsc: Install the storvsc specific timeout handler for FC devices
hisi_sas: fix v1 hw check for slot error
hisi_sas: add dependency for HAS_IOMEM
|
|
The pfn_t type uses an unsigned long to store a pfn + flags value. On a
64-bit platform the upper 12 bits of an unsigned long are never used for
storing the value of a pfn. However, this is not true on highmem
platforms, all 32-bits of a pfn value are used to address a 44-bit
physical address space. A pfn_t needs to store a 64-bit value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112211
Fixes: 01c8f1c44b83 ("mm, dax, gpu: convert vm_insert_mixed to pfn_t")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Stuart Foster <smf.linux@ntlworld.com>
Reported-by: Julian Margetson <runaway@candw.ms>
Tested-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Mike said:
: CONFIG_UBSAN_ALIGNMENT breaks x86-64 kernel with lockdep enabled, i. e
: kernel with CONFIG_UBSAN_ALIGNMENT fails to load without even any error
: message.
:
: The problem is that ubsan callbacks use spinlocks and might be called
: before lockdep is initialized. Particularly this line in the
: reserve_ebda_region function causes problem:
:
: lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
:
: If i put lockdep_init() before reserve_ebda_region call in
: x86_64_start_reservations kernel loads well.
Fix this ordering issue permanently: change lockdep so that it uses
hlists for the hash tables. Unlike a list_head, an hlist_head is in its
initialized state when it is all-zeroes, so lockdep is ready for
operation immediately upon boot - lockdep_init() need not have run.
The patch will also save some memory.
lockdep_init() and lockdep_initialized can be done away with now - a 4.6
patch has been prepared to do this.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Suggested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) Fix BPF handling of branch offset adjustmnets on backjumps, from
Daniel Borkmann.
2) Make sure selinux knows about SOCK_DESTROY netlink messages, from
Lorenzo Colitti.
3) Fix openvswitch tunnel mtu regression, from David Wragg.
4) Fix ICMP handling of TCP sockets in syn_recv state, from Eric
Dumazet.
5) Fix SCTP user hmacid byte ordering bug, from Xin Long.
6) Fix recursive locking in ipv6 addrconf, from Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices
geneve: Relax MTU constraints
vxlan: Relax MTU constraints
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
of: of_mdio: Add marvell, 88e1145 to whitelist of PHY compatibilities.
selinux: nlmsgtab: add SOCK_DESTROY to the netlink mapping tables
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
ipv6: fix a lockdep splat
unix: correctly track in-flight fds in sending process user_struct
update be2net maintainers' email addresses
dwc_eth_qos: Reset hardware before PHY start
ipv6: addrconf: Fix recursive spin lock call
|
|
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269b ("qla2xxx: Add selective command queuing")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
- PORTS_IMPL workaround for very early ahci controllers is misbehaving
on new systems. Disabled on recent ahci versions.
- Old-style PIO state machine had a horrible locking problem. Don't
know how we've been getting away this far. Fixed.
- Other device specific updates.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Intel DNV device IDs SATA
libata: fix sff host state machine locking while polling
libata-sff: use WARN instead of BUG on illegal host state machine state
libata: disable forced PORTS_IMPL for >= AHCI 1.3
libata: blacklist a Viking flash model for MWDMA corruption
drivers: ata: wake port before DMA stop for ALPM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- The destruction path of cgroup objects are asynchronous and
multi-staged and some of them ended up destroying parents before
children leading to failures in cpu and memory controllers. Ensure
that parents are always destroyed after children.
- cpuset mm node migration was performed synchronously while holding
threadgroup and cgroup mutexes and the recent threadgroup locking
update resulted in a possible deadlock. The migration is best effort
and shouldn't have been performed under those locks to begin with.
Made asynchronous.
- Minor documentation fix.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Documentation: cgroup: Fix 'cgroup-legacy' -> 'cgroup-v1'
cgroup: make sure a parent css isn't freed before its children
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Workqueue fixes for v4.5-rc3.
- Remove a spurious triggering of flush dependency warning.
- Officially break local execution guarantee of unbound work items
and add a debug feature to flush out usages which depend on it.
- Work around CPU -> NODE mapping becoming invalid on CPU offline.
The branch is young but pushing out early as stable kernels are being
affected"
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
workqueue: implement "workqueue.debug_force_rr_cpu" debug feature
workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: skip flush dependency checks for legacy workqueues
|
|
"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.
These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.
We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
|
|
All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.
Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
|
|
This adds ucs2_utf8size(), which tells us how big our ucs2 string is in
bytes, and ucs2_as_utf8, which translates from ucs2 to utf8..
Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
|
|
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Fix for async_probe module param added in 4.3 (clearly not widely used
yet), and a much more interesting kallsyms race which has been around
approximately forever. This fix is more invasive, and will require
some care in backporting, but I hated all the bandaids I could think
of, so...
There are some more coming, which are only for breakages introduced
this cycle (livepatch), but wanted these in now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modules: fix longstanding /proc/kallsyms vs module insertion race.
module: wrapper for symbol name.
modules: fix modparam async_probe request
|
|
Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.
This is of course incorrect.
A specific list of ICMP messages should be able to drop a SYN_RECV.
For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
See http: //www.infradead.org/rpr.html
X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org
Content-Transfer-Encoding: 8bit
Mime-Version: 1.0
We support OFFSET_MAX just fine, so don't round down below it. Also
switch to using min_t to make the helper more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 433c92379d9c ("NFS: Clean up nfs_size_to_loff_t()")
Cc: stable@vger.kernel.org # 2.6.23+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets")
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Considering current pty code and multiple devpts instances, it's possible
to umount a devpts file system while a program still has /dev/tty opened
pointing to a previosuly closed pty pair in that instance. In the case all
ptmx and pts/N files are closed, umount can be done. If the program closes
/dev/tty after umount is done, devpts_kill_index will use now an invalid
super_block, which was already destroyed in the umount operation after
running ->kill_sb. This is another "use after free" type of issue, but now
related to the allocated super_block instance.
To avoid the problem (warning at ida_remove and potential crashes) for
this specific case, I added two functions in devpts which grabs additional
references to the super_block, which pty code now uses so it makes sure
the super block structure is still valid until pty shutdown is done.
I also moved the additional inode references to the same functions, which
also covered similar case with inode being freed before /dev/tty final
close/shutdown.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Cc: stable@vger.kernel.org # 2.6.29+
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With CMD_T_FABRIC_STOP + se_cmd->cmd_wait_set usage in place,
go ahead and drop left-over CMD_T_REQUEST_STOP checks in
target_complete_cmd() and unused target_stop_cmd().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Merge fixes from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
m32r: fix build failure due to SMP and MMU
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"We have a few wire protocol compatibility fixes, ports of a few recent
CRUSH mapping changes, and a couple error path fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: MOSDOpReply v7 encoding
libceph: advertise support for TUNABLES5
crush: decode and initialize chooseleaf_stable
crush: add chooseleaf_stable tunable
crush: ensure take bucket value is valid
crush: ensure bucket id is valid before indexing buckets array
ceph: fix snap context leak in error path
ceph: checking for IS_ERR instead of NULL
|
|
Pull drm fixes from Dave Airlie:
"Fixes all over the place:
- amdkfd: two static checker fixes
- mst: a bunch of static checker and spec/hw interaction fixes
- amdgpu: fix Iceland hw properly, and some fiji bugs, along with
some write-combining fixes.
- exynos: some regression fixes
- adv7511: fix some EDID reading issues"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (38 commits)
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: change MST detection scheme
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/mst: Add range check for max_payloads during init
drm/mst: Don't ignore the MST PBN self-test result
drm: fix missing reference counting decrease
drm/amdgpu: disable uvd and vce clockgating on Fiji
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: load MEC ucode manually on iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu/gfx7: enable cp inst/reg error interrupts
drm/amdgpu/gfx8: enable cp inst/reg error interrupts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are: a fix for a recently introduced false-positive warnings
about PM domain pointers being changed inappropriately (harmless but
annoying), an MCH size workaround quirk for one more platform, a
compiler warning fix (generic power domains framework), an ACPI LPSS
(Intel SoCs) driver fixup and a cleanup of the ACPI CPPC core code.
Specifics:
- PM core fix to avoid false-positive warnings generated when the
pm_domain field is cleared for a device that appears to be bound to
a driver (Rafael Wysocki).
- New MCH size workaround quirk for Intel Haswell-ULT (Josh Boyer).
- Fix for an "unused function" compiler warning in the generic power
domains framework (Ulf Hansson).
- Fixup for the ACPI driver for Intel SoCs (acpi-lpss) to set the PM
domain pointer of a device properly in one place that was
overlooked by a recent PM core update (Andy Shevchenko).
- Removal of a redundant function declaration in the ACPI CPPC core
code (Timur Tabi)"
* tag 'pm+acpi-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Avoid false-positive warnings in dev_pm_domain_set()
PM / Domains: Silence compiler warning for an unused function
ACPI / CPPC: remove redundant mbox_send_message() declaration
ACPI / LPSS: set PM domain via helper setter
PNP: Add Haswell-ULT to Intel MCH size workaround
|
|
Helper radix_tree_iter_retry() resets next_index to the current index.
In following radix_tree_next_slot current chunk size becomes zero. This
isn't checked and it tries to dereference null pointer in slot.
Tagged iterator is fine because retry happens only at slot 0 where tag
bitmask in iter->tags is filled with single bit.
Fixes: 46437f9a554f ("radix-tree: fix race in gang lookup")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Jeremiah Mahler <jmmahler@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sequence vma_lock_anon_vma() - vma_unlock_anon_vma() isn't safe if
anon_vma appeared between lock and unlock. We have to check anon_vma
first or call anon_vma_prepare() to be sure that it's here. There are
only few users of these legacy helpers. Let's get rid of them.
This patch fixes anon_vma lock imbalance in validate_mm(). Write lock
isn't required here, read lock is enough.
And reorders expand_downwards/expand_upwards: security_mmap_addr() and
wrapping-around check don't have to be under anon vma lock.
Link: https://lkml.kernel.org/r/CACT4Y+Y908EjM2z=706dv4rV6dWtxTLK9nFg9_7DhRMLppBo2g@mail.gmail.com
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 944d9fec8d7a ("hugetlb: add support for gigantic page allocation
at runtime") has added the runtime gigantic page allocation via
alloc_contig_range(), making this support available only when CONFIG_CMA
is enabled. Because it doesn't depend on MIGRATE_CMA pageblocks and the
associated infrastructure, it is possible with few simple adjustments to
require only CONFIG_MEMORY_ISOLATION instead of full CONFIG_CMA.
After this patch, alloc_contig_range() and related functions are
available and used for gigantic pages with just CONFIG_MEMORY_ISOLATION
enabled. Note CONFIG_CMA selects CONFIG_MEMORY_ISOLATION. This allows
supporting runtime gigantic pages without the CMA-specific checks in
page allocator fastpaths.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.
It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.
Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.
Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
|
