| Age | Commit message (Collapse) | Author |
|---|
|
Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.
This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.
The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>
But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.
We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.
Cc: linux-gpio@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This converts the GPIO-based I2C-driver to using GPIO
descriptors instead of the old global numberspace-based
GPIO interface. We:
- Convert the driver to unconditionally grab two GPIOs
from the device by index 0 (SDA) and 1 (SCL) which
will work fine with device tree and descriptor tables.
The existing device trees will continue to work just
like before, but without any roundtrip through the
global numberspace.
- Brutally convert all boardfiles still passing global
GPIOs by registering descriptor tables associated with
the devices instead so this driver does not need to keep
supporting passing any GPIO numbers as platform data.
There is no stepwise approach as elegant as this, I
strongly prefer this big hammer over any antsteps for this
conversion. This way the old GPIO numbers go away and
NEVER COME BACK.
Special conversion for the different boards utilizing
I2C-GPIO:
- EP93xx (arch/arm/mach-ep93xx): pretty straight forward as
all boards were using the same two GPIO lines, just define
these two in a lookup table for "i2c-gpio" and register
these along with the device. None of them define any
other platform data so just pass NULL as platform data.
This platform selects GPIOLIB so all should be smooth.
The pins appear on a gpiochip for bank "G" as pins 1 (SDA)
and 0 (SCL).
- IXP4 (arch/arm/mach-ixp4): descriptor tables have to
be registered for each board separately. They all use
"IXP4XX_GPIO_CHIP" so it is pretty straight forward.
Most board define no other platform data than SCL/SDA
so they can drop the #include of <linux/i2c-gpio.h> and
assign NULL to platform data.
The "goramo_mlr" (Goramo Multilink Router) board is a bit
worrisome: it implements its own I2C bit-banging in the
board file, and optionally registers an I2C serial port,
but claims the same GPIO lines for itself in the board file.
This is not going to work: there will be competition for the
GPIO lines, so delete the optional extra I2C bus instead, no
I2C devices are registered on it anyway, there are just hints
that it may contain an EEPROM that may be accessed from
userspace. This needs to be fixed up properly by the serial
clock using I2C emulation so drop a note in the code.
- KS8695 board acs5k (arch/arm/mach-ks8695/board-acs5.c)
has some platform data in addition to the pins so it needs to
be kept around sans GPIO lines. Its GPIO chip is named
"KS8695" and the arch selects GPIOLIB.
- PXA boards (arch/arm/mach-pxa/*) use some of the platform
data so it needs to be preserved here. The viper board even
registers two GPIO I2Cs. The gpiochip is named "gpio-pxa" and
the arch selects GPIOLIB.
- SA1100 Simpad (arch/arm/mach-sa1100/simpad.c) defines a GPIO
I2C bus, and the arch selects GPIOLIB.
- Blackfin boards (arch/blackfin/bf533 etc) for these I assume
their I2C GPIOs refer to the local gpiochip defined in
arch/blackfin/kernel/bfin_gpio.c names "BFIN-GPIO".
The arch selects GPIOLIB. The boards get spiked with
IF_ENABLED(I2C_GPIO) but that is a side effect of it
being like that already (I would just have Kconfig select
I2C_GPIO and get rid of them all.) I also delete any
platform data set to 0 as it will get that value anyway
from static declartions of platform data.
- The MIPS selects GPIOLIB and the Alchemy machine is using
two local GPIO chips, one of them has a GPIO I2C. We need
to adjust the local offset from the global number space here.
The ATH79 has a proper GPIO driver in drivers/gpio/gpio-ath79.c
and AFAICT the chip is named "ath79-gpio" and the PB44
PCF857x expander spawns from this on GPIO 1 and 0. The latter
board only use the platform data to specify pins so it can be
cut altogether after this.
- The MFD Silicon Motion SM501 is a special case. It dynamically
spawns an I2C bus off the MFD using sm501_create_subdev().
We use an approach to dynamically create a machine descriptor
table and attach this to the "SM501-LOW" or "SM501-HIGH"
gpiochip. We use chip-local offsets to grab the right lines.
We can get rid of two local static inline helpers as part
of this refactoring.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Wu, Aaron <Aaron.Wu@analog.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is not a single user of the platform data header in
<linux/gpio-fan.h>. We can conclude that all current users are
probing from the device tree, so start simplifying the code by
pulling the header into the driver.
Convert "unsigned" to "unsigned int" in the process to make
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After finding out there are active users of this sensor I noticed:
- It has a single PXA27x board file using the platform data
- The platform data is only used to carry two GPIO pins, all other
fields are unused
- The driver does not use GPIO descriptors but the legacy GPIO
API
I saw we can swiftly fix this by:
- Killing off the platform data entirely
- Define a GPIO descriptor lookup table in the board file
- Use the standard devm_gpiod_get() to grab the GPIO descriptors
from either the device tree or the board file table.
This compiles, but needs testing.
Cc: arm@kernel.org
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Davide Hug <d@videhug.ch>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull networking fixes from David Miller:
1) Fix route leak in xfrm_bundle_create().
2) In mac80211, validate user rate mask before configuring it. From
Johannes Berg.
3) Properly enforce memory limits in fair queueing code, from Toke
Hoiland-Jorgensen.
4) Fix lockdep splat in inet_csk_route_req(), from Eric Dumazet.
5) Fix TSO header allocation and management in mvpp2 driver, from Yan
Markman.
6) Don't take socket lock in BH handler in strparser code, from Tom
Herbert.
7) Don't show sockets from other namespaces in AF_UNIX code, from
Andrei Vagin.
8) Fix double free in error path of tap_open(), from Girish Moodalbail.
9) Fix TX map failure path in igb and ixgbe, from Jean-Philippe Brucker
and Alexander Duyck.
10) Fix DCB mode programming in stmmac driver, from Jose Abreu.
11) Fix err_count handling in various tunnels (ipip, ip6_gre). From Xin
Long.
12) Properly align SKB head before building SKB in tuntap, from Jason
Wang.
13) Avoid matching qdiscs with a zero handle during lookups, from Cong
Wang.
14) Fix various endianness bugs in sctp, from Xin Long.
15) Fix tc filter callback races and add selftests which trigger the
problem, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
selftests: Introduce a new test case to tc testsuite
selftests: Introduce a new script to generate tc batch file
net_sched: fix call_rcu() race on act_sample module removal
net_sched: add rtnl assertion to tcf_exts_destroy()
net_sched: use tcf_queue_work() in tcindex filter
net_sched: use tcf_queue_work() in rsvp filter
net_sched: use tcf_queue_work() in route filter
net_sched: use tcf_queue_work() in u32 filter
net_sched: use tcf_queue_work() in matchall filter
net_sched: use tcf_queue_work() in fw filter
net_sched: use tcf_queue_work() in flower filter
net_sched: use tcf_queue_work() in flow filter
net_sched: use tcf_queue_work() in cgroup filter
net_sched: use tcf_queue_work() in bpf filter
net_sched: use tcf_queue_work() in basic filter
net_sched: introduce a workqueue for RCU callbacks of tc filter
sctp: fix some type cast warnings introduced since very beginning
sctp: fix a type cast warnings that causes a_rwnd gets the wrong value
sctp: fix some type cast warnings introduced by transport rhashtable
sctp: fix some type cast warnings introduced by stream reconf
...
|
|
This patch introduces a dedicated workqueue for tc filters
so that each tc filter's RCU callback could defer their
action destroy work to this workqueue. The helper
tcf_queue_work() is introduced for them to use.
Because we hold RTNL lock when calling tcf_block_put(), we
can not simply flush works inside it, therefore we have to
defer it again to this workqueue and make sure all flying RCU
callbacks have already queued their work before this one, in
other words, to ensure this is the last one to execute to
prevent any use-after-free.
On the other hand, this makes tcf_block_put() ugly and
harder to understand. Since David and Eric strongly dislike
adding synchronize_rcu(), this is probably the only
solution that could make everyone happy.
Please also see the code comments below.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch increases the connection timeout for LE connections that are
triggered by the advertising report to 4 seconds.
It has been observed that devices equipped with wifi+bt combo SoC fail
to create a connection with BLE devices due to their coexistence issues.
Increasing this timeout gives them enough time to complete the
connection with success.
Signed-off-by: Konrad Zapałowicz <konrad.zapalowicz@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is very similar to the Macvlan VEPA mode, however, there is some
difference. IPvlan uses the mac-address of the lower device, so the VEPA
mode has implications of ICMP-redirects for packets destined for its
immediate neighbors sharing same master since the packets will have same
source and dest mac. The external switch/router will send redirect msg.
Having said that, this will be useful tool in terms of debugging
since IPvlan will not switch packets within its slaves and rely completely
on the external entity as intended in 802.1Qbg.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPvlan has always operated in bridge mode. However there are scenarios
where each slave should be able to talk through the master device but
not necessarily across each other. Think of an environment where each
of a namespace is a private and independant customer. In this scenario
the machine which is hosting these namespaces neither want to tell who
their neighbor is nor the individual namespaces care to talk to neighbor
on short-circuited network path.
This patch implements the mode that is very similar to the 'private' mode
in macvlan where individual slaves can send and receive traffic through
the master device, just that they can not talk among slave devices.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian when coding stream
reconf patches.
Since commit c0d8bab6ae51 ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.
Fixes: c0d8bab6ae51 ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cached routes should only be created by the system when receiving pmtu
discovery or ip redirect msg. Users should not be allowed to create
cached routes.
Furthermore, after the patch series to move cached routes into exception
table, user added cached routes will trigger the following warning in
fib6_add():
WARNING: CPU: 0 PID: 2985 at net/ipv6/ip6_fib.c:1137
fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 2985 Comm: syzkaller320388 Not tainted 4.14.0-rc3+ #74
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x417 kernel/panic.c:181
__warn+0x1c4/0x1d9 kernel/panic.c:542
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
RSP: 0018:ffff8801cf09f6a0 EFLAGS: 00010297
RAX: ffff8801ce45e340 RBX: 1ffff10039e13eec RCX: ffff8801d749c814
RDX: 0000000000000000 RSI: ffff8801d749c700 RDI: ffff8801d749c780
RBP: ffff8801cf09fa08 R08: 0000000000000000 R09: ffff8801cf09f360
R10: ffff8801cf09f2d8 R11: 1ffff10039c8befb R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d749c700 R15: ffffffff860655c0
__ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1011
ip6_route_add+0x148/0x1a0 net/ipv6/route.c:2782
ipv6_route_ioctl+0x4d5/0x690 net/ipv6/route.c:3291
inet6_ioctl+0xef/0x1e0 net/ipv6/af_inet6.c:521
sock_do_ioctl+0x65/0xb0 net/socket.c:961
sock_ioctl+0x2c2/0x440 net/socket.c:1058
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1530 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
So we fix this by failing the attemp to add cached routes from userspace
with returning EINVAL error.
Fixes: 2b760fcf5cfb ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-27
This patchset is a proposal of how the Traffic Control subsystem can
be used to offload the configuration of the Credit Based Shaper
(defined in the IEEE 802.1Q-2014 Section 8.6.8.2) into supported
network devices.
As part of this work, we've assessed previous public discussions
related to TSN enabling: patches from Henrik Austad (Cisco), the
presentation from Eric Mann at Linux Plumbers 2012, patches from
Gangfeng Huang (National Instruments) and the current state of the
OpenAVNU project (https://github.com/AVnu/OpenAvnu/).
Overview
========
Time-sensitive Networking (TSN) is a set of standards that aim to
address resources availability for providing bandwidth reservation and
bounded latency on Ethernet based LANs. The proposal described here
aims to cover mainly what is needed to enable the following standards:
802.1Qat and 802.1Qav.
The initial target of this work is the Intel i210 NIC, but other
controllers' datasheet were also taken into account, like the Renesas
RZ/A1H RZ/A1M group and the Synopsis DesignWare Ethernet QoS
controller.
Proposal
========
Feature-wise, what is covered here is the configuration interfaces for
HW implementations of the Credit-Based shaper (CBS, 802.1Qav). CBS is
a per-queue shaper. Given that this feature is related to traffic
shaping, and that the traffic control subsystem already provides a
queueing discipline that offloads config into the device driver (i.e.
mqprio), designing a new qdisc for the specific purpose of offloading
the config for the CBS shaper seemed like a good fit.
For steering traffic into the correct queues, we use the socket option
SO_PRIORITY and then a mechanism to map priority to traffic classes /
Tx queues. The qdisc mqprio is currently used in our tests.
As for the CBS config interface, this patchset is proposing a new
qdisc called 'cbs'. Its 'tc' cmd line is:
$ tc qdisc add dev IFACE parent ID cbs locredit N hicredit M sendslope S \
idleslope I
Note that the parameters for this qdisc are the ones defined by the
802.1Q-2014 spec, so no hardware specific functionality is exposed here.
Per-stream shaping, as defined by IEEE 802.1Q-2014 Section 34.6.1, is
not yet covered by this proposal.
v2: Merged patch 6 of the original series into patch 4 based on feedback
from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds of_i2c_setup_smbus_alert which allows the smbalert
driver to be attached to an i2c adapter via the device tree.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Prior to this commit the smbalert_irq was handling in the hard irq
context. This change switch to using a thread irq which avoids the need
for the work thread. Using threaded irq also removes the need for the
edge_triggered flag as the enabling / disabling of the hard irq for level
triggered interrupts will be handled by the irq core.
Without this change have an irq connected to something like an i2c gpio
resulted in a null ptr deferences. Specifically handle_nested_irq calls
the threaded irq handler.
There are currently 3 in tree drivers affected by this change.
i2c-parport driver calls i2c_handle_smbus_alert in a hard irq context.
This driver use edge trigger interrupts which skip the enable / disable
calls. But it still need to handle the smbus transaction on a thread. So
the work thread is kept for this driver.
i2c-parport-light & i2c-thunderx-pcidrv provide the irq number in the
setup which will result in the thread irq being used.
i2c-parport-light is edge trigger so the enable / disable call was
skipped as well.
i2c-thunderx-pcidrv is getting the edge / level trigger setting from of
data and was setting the flag as required. However the irq core should
handle this automatically.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
two extra #include are not necessary in tcp.h
Remove them.
Fixes: 40304b2a1567 ("bpf: BPF support for sock_ops")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 9a393b5d5988 ("tap: tap as an independent module") created a
separate tap module that implements tap functionality and exports
interfaces that will be used by macvtap and ipvtap modules to create
create respective tap devices.
However, that patch introduced a regression wherein the modules macvtap
and ipvtap can be removed (through modprobe -r) while there are
applications using the respective /dev/tapX devices. These applications
cause kernel to hold reference to /dev/tapX through 'struct cdev
macvtap_cdev' and 'struct cdev ipvtap_dev' defined in macvtap and ipvtap
modules respectively. So, when the application is later closed the
kernel panics because we are referencing KVA that is present in the
unloaded modules.
----------8<------- Example ----------8<----------
$ sudo ip li add name mv0 link enp7s0 type macvtap
$ sudo ip li show mv0 |grep mv0| awk -e '{print $1 $2}'
14:mv0@enp7s0:
$ cat /dev/tap14 &
$ lsmod |egrep -i 'tap|vlan'
macvtap 16384 0
macvlan 24576 1 macvtap
tap 24576 3 macvtap
$ sudo modprobe -r macvtap
$ fg
cat /dev/tap14
^C
<...system panics...>
BUG: unable to handle kernel paging request at ffffffffa038c500
IP: cdev_put+0xf/0x30
----------8<-----------------8<----------
The fix is to set cdev.owner to the module that creates the tap device
(either macvtap or ipvtap). With this set, the operations (in
fs/char_dev.c) on char device holds and releases the module through
cdev_get() and cdev_put() and will not allow the module to unload
prematurely.
Fixes: 9a393b5d5988ea4e (tap: tap as an independent module)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Update the <linux/swait.h> documentation to discourage their use"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/swait: Document it clearly that the swait facilities are special and shouldn't be used
|
|
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
|
|
Linux 4.14-rc7
Requested by Ben Skeggs for nouveau to avoid major conflicts,
and things were getting a bit conflicty already, esp around amdgpu
reverts.
|
|
git://people.freedesktop.org/~robclark/linux into drm-next
+ preemption support for a5xx[1][2]
+ display fixes for 8x96 (snapdragon 820) including fixes for 4k scanout
(hwpipe assignment re-work to handle multiple hwpipe assigned to plane
for wide scanout)
+ async cursor plane updates and fixes
+ refactor adreno_bind/hwinit.. still defer fw loading until device open,
but move clk/irq/etc to probe/bind time to fix issues when fw isn't
present in filesys
+ clk/dt bindings cleanups w/ backward compat via msm_clk_get() (dt docs
part ack'ed by Rob Herring)
+ fw loading re-work with helper to handle either /lib/firmware/qcom/$fw
or /lib/firmware/$fw.. background, we've started landing fw for some of
generations in linux-firmware, but there is a preference to put fw files
under 'qcom' subdirectory, which is not what was done on android or for
people who copied fw from android. So now we first look in qcom subdir
and then fallback to the original location.
+ bunch of GPU debugging enhancements, to dump full cmdline of processes
that trigger faults, and to add a new debugfs to capture cmdstream of
just submits that triggered faults.. both quite useful for piglit ;-)
* tag 'drm-msm-next-2017-11-01' of git://people.freedesktop.org/~robclark/linux: (38 commits)
drm/msm: use %z format modifier for printing size_t
drm/msm/mdp5: Don't use async plane update path if plane visibility changes
drm/msm/mdp5: mdp5_crtc: Restore cursor state only if LM cursors are enabled
drm/msm/mdp5: Update mdp5_pipe_assign to spit out both planes
drm/msm/mdp5: Prepare mdp5_pipe_assign for some rework
drm/msm: remove mdp5_cursor_plane_funcs
drm/msm: update cursors asynchronously through atomic
drm/msm/atomic: switch to drm_atomic_helper_check
drm/msm/mdp5: restore cursor state when enabling crtc
drm/msm/mdp5: don't use autosuspend
drm/msm/mdp5: ignore planes that are not visible
drm/msm: dump submits which triggered gpu hang
drm/msm: preserve IOVAs in submit's bo table
drm/msm/rd: allow adding addition msg to top of dump
drm/msm: split rd debugfs file
drm/msm: add special _get_vaddr_active() for cmdstream dumps
drm/msm: show task cmdline in gpu recovery messages
drm/msm: dump a rd GPUADDR header for all buffers in the command
drm/msm: Removed unused struct_mutex_task
drm/msm: Implement preemption for A5XX targets
...
|
|
In order to manage ringbuffer priority to its fullest userspace
should know how many ringbuffers it has to work with. Add a
parameter to return the number of active rings.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add the infrastructure to support the idea of multiple ringbuffers.
Assign each ringbuffer an id and use that as an index for the various
ring specific operations.
The biggest delta is to support legacy fences. Each fence gets its own
sequence number but the legacy functions expect to use a unique integer.
To handle this we return a unique identifier for each submission but
map it to a specific ring/sequence under the covers. Newer users use
a dma_fence pointer anyway so they don't care about the actual sequence
ID or ring.
The actual mechanics for multiple ringbuffers are very target specific
so this code just allows for the possibility but still only defines
one ringbuffer for each target family.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Currently the behavior of a command stream is provided by the user
application during submission and the application is expected to internally
maintain the settings for each 'context' or 'rendering queue' and specify
the correct ones.
This works okay for simple cases but as applications become more
complex we will want to set context specific flags and do various
permission checks to allow certain contexts to enable additional
privileges.
Add kernel-side submit queues to be analogous to 'contexts' or
'rendering queues' on the application side. Each file descriptor
instance will maintain its own list of queues. Queues cannot be
shared between file descriptors.
For backwards compatibility context id '0' is defined as a default
context specifying no priority and no special flags. This is
intended to be the usual configuration for 99% of applications so
that a garden variety application can function correctly without
creating a queue. Only those applications requiring the specific
benefit of different queues need create one.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This adds support for offloading the CBS algorithm to the controller,
if supported. Drivers wanting to support CBS offload must implement
the .ndo_setup_tc callback and handle the TC_SETUP_CBS (introduced
here) type.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Henrik Austad <henrik@austad.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This queueing discipline implements the shaper algorithm defined by
the 802.1Q-2014 Section 8.6.8.2 and detailed in Annex L.
It's primary usage is to apply some bandwidth reservation to user
defined traffic classes, which are mapped to different queues via the
mqprio qdisc.
Only a simple software implementation is added for now.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Henrik Austad <henrik@austad.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a NEC protocol type remote controller distributed with
96boards poplar@tocoding board.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a NEC protocol type remote controller distributed with
hisilicon TV demo boards.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that DSA exposes an enumerated type for the ports, we can use them
directly instead of checking bitmaps, which is more consistent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to know if a port is of type user, dsa_is_normal_port checks
that the given port is not of type DSA nor CPU. This is not enough
because a port can be unused.
Without the previous fix, this caused the unused mv88e6xxx ports to be
configured in normal mode.
The ds->enabled_port_mask reports the user ports, so check this instead.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch require net/dsa/tag_lan9303.c to access struct lan9303.
Therefore move struct lan9303 definitions from drivers/net/dsa/lan9303.h
to new file include/linux/dsa/lan9303.h.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
