| Age | Commit message (Collapse) | Author |
|---|
|
On the zoned mode, once used and freed region is still not reusable after the
freeing. The underlying zone needs to be reset before reusing. Btrfs resets a
zone when it removes a block group, and then new block group is allocated on
the zones to reuse the zones. But, it is sometime too late to catch up with a
write side.
This commit introduces a new space-info reclaim method ZONE_RESET. That will
pick a block group from the unused list and reset its zone to reuse the
zone_unusable space. It is faster than removing the block group and re-creating
a new block group on the same zones.
For the first implementation, the ZONE_RESET is only applied to a block group
whose region is fully zone_unusable. Reclaiming partial zone_unusable block
group could be implemented later.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, the sequence goes like this (among others):
1. flush all stations (including the AP ones) -> this will tell the
drivers to remove the stations
2. notify the driver the vif is not associated.
Which means that in between 1 and 2, the state is that the vif is
associated, but there is no AP station, which makes no sense, and may be
problematic for some drivers (for example iwlwifi)
Change the sequence to:
1. flush the TDLS stations
2. move the AP station to IEEE80211_STA_NONE
3. notify the driver about the vif being unassociated
4. flush the AP station
In order to not break other drivers, add a vif flag to indicate whether
the driver wants to new sequence or not. If the flag is not set, then
things will be done in the old sequence.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241224192322.996ad1be6cb3.I7815d33415aa1d65c0120b54be7a15a45388f807@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When mremap()ing a memory region previously registered with userfaultfd as
write-protected but without UFFD_FEATURE_EVENT_REMAP, an inconsistency in
flag clearing leads to a mismatch between the vma flags (which have
uffd-wp cleared) and the pte/pmd flags (which do not have uffd-wp
cleared). This mismatch causes a subsequent mprotect(PROT_WRITE) to
trigger a warning in page_table_check_pte_flags() due to setting the pte
to writable while uffd-wp is still set.
Fix this by always explicitly clearing the uffd-wp pte/pmd flags on any
such mremap() so that the values are consistent with the existing clearing
of VM_UFFD_WP. Be careful to clear the logical flag regardless of its
physical form; a PTE bit, a swap PTE bit, or a PTE marker. Cover PTE,
huge PMD and hugetlb paths.
Link: https://lkml.kernel.org/r/20250107144755.1871363-2-ryan.roberts@arm.com
Co-developed-by: Mikołaj Lenczewski <miko.lenczewski@arm.com>
Signed-off-by: Mikołaj Lenczewski <miko.lenczewski@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Closes: https://lore.kernel.org/linux-mm/810b44a8-d2ae-4107-b665-5a42eae2d948@arm.com/
Fixes: 63b2d4174c4a ("userfaultfd: wp: add the writeprotect API to userfaultfd ioctl")
Cc: David Hildenbrand <david@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Peter Xu <peterx@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
A livepatch module can contain a special relocation section
.klp.rela.<objname>.<secname> to apply its relocations at the appropriate
time and to additionally access local and unexported symbols. When
<objname> points to another module, such relocations are processed
separately from the regular module relocation process. For instance, only
when the target <objname> actually becomes loaded.
With CONFIG_STRICT_MODULE_RWX, when the livepatch core decides to apply
these relocations, their processing results in the following bug:
[ 25.827238] BUG: unable to handle page fault for address: 00000000000012ba
[ 25.827819] #PF: supervisor read access in kernel mode
[ 25.828153] #PF: error_code(0x0000) - not-present page
[ 25.828588] PGD 0 P4D 0
[ 25.829063] Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 25.829742] CPU: 2 UID: 0 PID: 452 Comm: insmod Tainted: G O K 6.13.0-rc4-00078-g059dd502b263 #7820
[ 25.830417] Tainted: [O]=OOT_MODULE, [K]=LIVEPATCH
[ 25.830768] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
[ 25.831651] RIP: 0010:memcmp+0x24/0x60
[ 25.832190] Code: [...]
[ 25.833378] RSP: 0018:ffffa40b403a3ae8 EFLAGS: 00000246
[ 25.833637] RAX: 0000000000000000 RBX: ffff93bc81d8e700 RCX: ffffffffc0202000
[ 25.834072] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 00000000000012ba
[ 25.834548] RBP: ffffa40b403a3b68 R08: ffffa40b403a3b30 R09: 0000004a00000002
[ 25.835088] R10: ffffffffffffd222 R11: f000000000000000 R12: 0000000000000000
[ 25.835666] R13: ffffffffc02032ba R14: ffffffffc007d1e0 R15: 0000000000000004
[ 25.836139] FS: 00007fecef8c3080(0000) GS:ffff93bc8f900000(0000) knlGS:0000000000000000
[ 25.836519] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 25.836977] CR2: 00000000000012ba CR3: 0000000002f24000 CR4: 00000000000006f0
[ 25.837442] Call Trace:
[ 25.838297] <TASK>
[ 25.841083] __write_relocate_add.constprop.0+0xc7/0x2b0
[ 25.841701] apply_relocate_add+0x75/0xa0
[ 25.841973] klp_write_section_relocs+0x10e/0x140
[ 25.842304] klp_write_object_relocs+0x70/0xa0
[ 25.842682] klp_init_object_loaded+0x21/0xf0
[ 25.842972] klp_enable_patch+0x43d/0x900
[ 25.843572] do_one_initcall+0x4c/0x220
[ 25.844186] do_init_module+0x6a/0x260
[ 25.844423] init_module_from_file+0x9c/0xe0
[ 25.844702] idempotent_init_module+0x172/0x270
[ 25.845008] __x64_sys_finit_module+0x69/0xc0
[ 25.845253] do_syscall_64+0x9e/0x1a0
[ 25.845498] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 25.846056] RIP: 0033:0x7fecef9eb25d
[ 25.846444] Code: [...]
[ 25.847563] RSP: 002b:00007ffd0c5d6de8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 25.848082] RAX: ffffffffffffffda RBX: 000055b03f05e470 RCX: 00007fecef9eb25d
[ 25.848456] RDX: 0000000000000000 RSI: 000055b001e74e52 RDI: 0000000000000003
[ 25.848969] RBP: 00007ffd0c5d6ea0 R08: 0000000000000040 R09: 0000000000004100
[ 25.849411] R10: 00007fecefac7b20 R11: 0000000000000246 R12: 000055b001e74e52
[ 25.849905] R13: 0000000000000000 R14: 000055b03f05e440 R15: 0000000000000000
[ 25.850336] </TASK>
[ 25.850553] Modules linked in: deku(OK+) uinput
[ 25.851408] CR2: 00000000000012ba
[ 25.852085] ---[ end trace 0000000000000000 ]---
The problem is that the .klp.rela.<objname>.<secname> relocations are
processed after the module was already formed and mod->rw_copy was reset.
However, the code in __write_relocate_add() calls
module_writable_address() which translates the target address 'loc' still
to 'loc + (mem->rw_copy - mem->base)', with mem->rw_copy now being 0.
Fix the problem by returning directly 'loc' in module_writable_address()
when the module is already formed. Function __write_relocate_add() knows
to use text_poke() in such a case.
Link: https://lkml.kernel.org/r/20250107153507.14733-1-petr.pavlu@suse.com
Fixes: 0c133b1e78cd ("module: prepare to handle ROX allocations for text")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reported-by: Marek Maslanka <mmaslanka@google.com>
Closes: https://lore.kernel.org/linux-modules/CAGcaFA2hdThQV6mjD_1_U+GNHThv84+MQvMWLgEuX+LVbAyDxg@mail.gmail.com/
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
hugetlb_file_setup() will pass a NULL @dir to hugetlbfs_get_inode(), so we
will access a NULL pointer for @dir. Fix it and set __entry->dr to 0 if
@dir is NULL. Because ->i_ino cannot be 0 (see get_next_ino()), there is
no confusing if user sees a 0 inode number.
Link: https://lkml.kernel.org/r/20250106033118.4640-1-songmuchun@bytedance.com
Fixes: 318580ad7f28 ("hugetlbfs: support tracepoint")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reported-by: Cheung Wall <zzqq0103.hey@gmail.com>
Closes: https://lore.kernel.org/linux-mm/02858D60-43C1-4863-A84F-3C76A8AF1F15@linux.dev/T/#
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Cc: cheung wall <zzqq0103.hey@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
drm-next
Updates for v6.14
MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
MDP4:
- several small fixes
DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- fixed modes filtering for platforms w/o 3DMux
- fixed DSPP DSPP_2 / _3 links on several platforms
- corrected DSPP definitions on SDM670
- added CWB hardware blocks support
- added VBIF to DPU snapshots
- dropped struct dpu_rm_requirements
DP:
- reworked DP audio support
DSI:
- added SM6150 (aka QCS615) support
GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver Changes:
- SRIOV VF: Avoid reading inaccessible registers (Jakub, Marcin)
- Introduce RPa frequency information (Rodrigo)
- Remove unnecessary force wakes on SLPC code (Vinay)
- Fix all typos in xe (Nitin)
- Adding steering info support for GuC register lists (Jesus)
- Remove unused xe_pciids.h harder, add missing PCI ID (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Z4E0tlTAA6MZ7PF2@intel.com
|
|
There are multiple open coded implementations for getting the parity of
a byte in the kernel, even using different approaches. Take the pretty
efficient version from SPD5118 driver and make it generally available by
putting it into the bitops header. As long as there is just one parity
calculation helper, the creation of a distinct 'parity.h' header was
discarded. Also, the usage of hweight8() for architectures having a
popcnt instruction is postponed until a use case within hot paths is
desired. The motivation for this patch is the frequent use of odd parity
in the I3C specification and to simplify drivers there.
Changes compared to the original SPD5118 version are the addition of
kernel documentation, switching the return type from bool to int, and
renaming the argument of the function.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Tested-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20250107090204.6593-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
A typo mentioned I3C when it should have been I2C.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20241219220338.10315-1-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"The largest part here is for KVM/PPC, where a NULL pointer dereference
was introduced in the 6.13 merge window and is now fixed.
There's some "holiday-induced lateness", as the s390 submaintainer put
it, but otherwise things looks fine.
s390:
- fix a latent bug when the kernel is compiled in debug mode
- two small UCONTROL fixes and their selftests
arm64:
- always check page state in hyp_ack_unshare()
- align set_id_regs selftest with the fact that ASIDBITS field is RO
- various vPMU fixes for bugs that only affect nested virt
PPC e500:
- Fix a mostly impossible (but just wrong) case where IRQs were never
re-enabled
- Observe host permissions instead of mapping readonly host pages as
guest-writable. This fixes a NULL-pointer dereference in 6.13
- Replace brittle VMA-based attempts at building huge shadow TLB
entries with PTE lookups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: e500: perform hugepage check after looking up the PFN
KVM: e500: map readonly host pages for read
KVM: e500: track host-writability of pages
KVM: e500: use shadow TLB entry as witness for writability
KVM: e500: always restore irqs
KVM: s390: selftests: Add has device attr check to uc_attr_mem_limit selftest
KVM: s390: selftests: Add ucontrol gis routing test
KVM: s390: Reject KVM_SET_GSI_ROUTING on ucontrol VMs
KVM: s390: selftests: Add ucontrol flic attr selftests
KVM: s390: Reject setting flic pfault attributes on ucontrol VMs
KVM: s390: vsie: fix virtual/physical address in unpin_scb()
KVM: arm64: Only apply PMCR_EL0.P to the guest range of counters
KVM: arm64: nv: Reload PMU events upon MDCR_EL2.HPME change
KVM: arm64: Use KVM_REQ_RELOAD_PMU to handle PMCR_EL0.E change
KVM: arm64: Add unified helper for reprogramming counters by mask
KVM: arm64: Always check the state from hyp_ack_unshare()
KVM: arm64: Fix set_id_regs selftest for ASIDBITS becoming unwritable
|
|
So far we notify the sequencer client and port changes upon UMP FB
changes, but those aren't really corresponding to the UMP updates.
e.g. when a FB info gets updated, it's not notified but done only when
some of sequencer port attribute is changed. This is no ideal
behavior.
This patch adds the two new sequencer event types for notifying the
UMP EP and FB changes via the announce port. The new event takes
snd_seq_ev_ump_notify type data, which is compatible with
snd_seq_addr (where the port number is replaced with the block
number).
The events are sent when the EP and FB info gets updated explicitly
via ioctl, or the backend UMP receives the corresponding UMP
messages.
The sequencer protocol version is bumped to 1.0.5 along with it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250110155943.31578-9-tiwai@suse.de
|
|
Bump the protocol version to 2.0.5, as we extended the rawmidi ABI for
the new tied_device info and the substream inactive flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250110155943.31578-4-tiwai@suse.de
|
|
The UMP legacy rawmidi may turn on/off the substream dynamically
depending on the UMP Function Block information. So far, there was no
direct way to know whether the substream is disabled (inactive) or
not; at most one can take a look at the substream name string or try
to open and get -ENODEV.
This patch extends the rawmidi info ioctl to show the current inactive
state of the given substream. When the selected substream is
inactive, info flags field contains the new bit flag
SNDRV_RAWMIDI_INFO_STREAM_INACTIVE.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250110155943.31578-3-tiwai@suse.de
|
|
The UMP legacy rawmidi is derived from the UMP rawmidi, but currently
there is no way to know which device is involved in other side.
This patch extends the rawmidi info ioctl to show the tied device
number. As default it stores -1, indicating that no tied device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250110155943.31578-2-tiwai@suse.de
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: three small bugfixes
Fix a latent bug when the kernel is compiled in debug mode.
Two small UCONTROL fixes and their selftests.
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 changes for 6.13, part #3
- Always check page state in hyp_ack_unshare()
- Align set_id_regs selftest with the fact that ASIDBITS field is RO
- Various vPMU fixes for bugs that only affect nested virt
|
|
Add nic_cap_reg and vhca_icm_ctrl registers interfaces for exposing ICM
consumption.
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109204231.1809851-5-tariqt@nvidia.com
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Read and cache SHAMPO specific caps for header data split capabilities.
Will be used in downstream patch.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109204231.1809851-4-tariqt@nvidia.com
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Management Real Time Clock Query (MRTCQ) register is used to query
hardware clock identity.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109204231.1809851-3-tariqt@nvidia.com
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add FEC admin and override related fields in PPLM, and the bit in PCAM
to indicate those fields are supported.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250109204231.1809851-2-tariqt@nvidia.com
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
If the <kunit/platform_device.h> header is included in a test without
certain other headers, it produces compiler warnings like:
In file included from [...]
../include/kunit/platform_device.h:15:57: warning: ‘struct completion’
declared inside parameter list will not be visible outside of this
definition or declaration
15 | struct completion *x);
| ^~~~~~~~~~
Add a 'struct completion' forward declaration to resolve this.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Move kvfree_rcu() functionality to the slab_common.c file.
The reason to have kvfree_rcu() functionality as part of SLAB is that
there is a clear trend and need of closer integration. One of the recent
example is creating a barrier function for SLAB caches.
Another reason is to prevent of having several implementations of RCU
machinery for reclaiming objects after a GP. As future steps, it can be
more integrated(easier) with SLAB internals.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Acked-by: Hyeonggon Yoo <hyeonggon.yoo@sk.com>
Tested-by: Hyeonggon Yoo <hyeonggon.yoo@sk.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Introduce a separate initialization of kvfree_rcu() functionality.
For such purpose a kfree_rcu_batch_init() is renamed to a kvfree_rcu_init()
and it is invoked from the main.c right after rcu_init() is done.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Acked-by: Hyeonggon Yoo <hyeonggon.yoo@sk.com>
Tested-by: Hyeonggon Yoo <hyeonggon.yoo@sk.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Over the Christmas break a couple of devicetree fixes came in for
Rockchips, Qualcomm and NXP/i.MX. These add some missing board
specific properties, address build time warnings,
The USB/TOG supoprt on X1 Elite regressed, so two earlier DT changes
get reverted for now.
Aside from the devicetree fixes, there is One build fix for the stm32
firewall driver, and a defconfig change to enable SPDIF support for
i.MX"
* tag 'soc-fixes-6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firewall: remove misplaced semicolon from stm32_firewall_get_firewall
arm64: dts: rockchip: add hevc power domain clock to rk3328
arm64: dts: rockchip: Fix the SD card detection on NanoPi R6C/R6S
arm64: dts: qcom: sa8775p: fix the secure device bootup issue
Revert "arm64: dts: qcom: x1e80100: enable OTG on USB-C controllers"
Revert "arm64: dts: qcom: x1e80100-crd: enable otg on usb ports"
arm64: dts: qcom: x1e80100: Fix up BAR space size for PCIe6a
Revert "arm64: dts: qcom: x1e78100-t14s: enable otg on usb-c ports"
ARM: dts: imxrt1050: Fix clocks for mmc
ARM: imx_v6_v7_defconfig: enable SND_SOC_SPDIF
arm64: dts: imx95: correct the address length of netcmix_blk_ctrl
arm64: dts: imx8-ss-audio: add fallback compatible string fsl,imx6ull-esai for esai
arm64: dts: rockchip: rename rfkill label for Radxa ROCK 5B
arm64: dts: rockchip: add reset-names for combphy on rk3568
arm64: dts: qcom: sa8775p: Fix the size of 'addr_space' regions
|
|
The NVMe specifications mandate support for the host identifier
set_features for controllers that also supports reservations. Satisfy
this requirement by implementing handling of the NVME_FEAT_HOST_ID
feature for the nvme_set_features command. This implementation is for
now effective only for PCI target controllers. For other controller
types, the set features command is failed with a NVME_SC_CMD_SEQ_ERROR
status as before.
As noted in the code, 128 bits host identifiers are supported since the
NVMe base specifications version 2.1 indicate in section 5.1.25.1.28.1
that "The controller may support a 64-bit Host Identifier...".
The RHII (Reservations and Host Identifier Interaction) bit of the
controller attribute (ctratt) field of the identify controller data is
also set to indicate that a host ID of "0" is supported but that the
host ID must be a non-zero value to use reservations.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Define the transport type NVMF_TRTYPE_PCI for PCI endpoint targets.
This transport type is defined using the value 0 which is reserved in
the NVMe base specifications v2.1 (Figure 294). Given that struct
nvmet_port are zeroed out on creation, to avoid having this transsport
type becoming the new default, nvmet_referral_make() and
nvmet_ports_make() are modified to initialize a port discovery address
transport type field (disc_addr.trtype) to NVMF_TRTYPE_MAX.
Any port using this transport type is also skipped and not reported in
the discovery log page (nvmet_execute_disc_get_log_page()).
The helper function nvmet_is_pci_ctrl() is also introduced to check if
a target controller uses the PCI transport.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Move the declaration of all helper functions converting NVMe command
opcodes and status codes into strings from drivers/nvme/host/nvme.h
into include/linux/nvme.h, together with the commands definitions.
This allows NVMe target drivers to call these functions without having
to include a host header file.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
There are no module callers of dev_get_by_napi_id(),
and commit d1cacd747768 ("netdev: prevent accessing NAPI instances
from another namespace") proves that getting NAPI by id
needs to be done with care. So hide dev_get_by_napi_id().
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250110004924.3212260-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 86e25f40aa1e ("net: napi: Add napi_config") moved napi->napi_id
assignment to a later point in time (napi_hash_add_with_id). This breaks
__xdp_rxq_info_reg which copies napi_id at an earlier time and now
stores 0 napi_id. It also makes sk_mark_napi_id_once_xdp and
__sk_mark_napi_id_once useless because they now work against 0 napi_id.
Since sk_busy_loop requires valid napi_id to busy-poll on, there is no way
to busy-poll AF_XDP sockets anymore.
Bring back the ability to busy-poll on XSK by resolving socket's napi_id
at bind time. This relies on relatively recent netif_queue_set_napi,
but (assume) at this point most popular drivers should have been converted.
This also removes per-tx/rx cycles which used to check and/or set
the napi_id value.
Confirmed by running a busy-polling AF_XDP socket
(github.com/fomichev/xskrtt) on mlx5 and looking at BusyPollRxPackets
from /proc/net/netstat.
Fixes: 86e25f40aa1e ("net: napi: Add napi_config")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250109003436.2829560-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function to allow configuration of the PCS's clock stop enable
bit, used to configure whether the xMII receive clock can be stopped
during LPI mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tVZDR-0002Jl-Ry@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 9a213d3b80c0, we can pass additional attributes along with
read/write. However, userspace doesn't know that. Add a new feature flag
IORING_FEAT_RW_ATTR, to notify the userspace that the kernel has this
ability.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20241205062109.1788-1-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
DMEM cgroup pull request
This introduces a new cgroup controller to limit the device memory.
Notable users would be DRM, dma-buf heaps, or v4l2.
This pull request is based on the series developped by Maarten
Lankhorst, Friedrich Vock, and I:
https://lore.kernel.org/all/20241204134410.1161769-1-dev@lankhorst.se/
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110-cryptic-warm-mandrill-b71f5d@houat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"afs:
- Fix the maximum cell name length
- Fix merge preference rule failure condition
fuse:
- Fix fuse_get_user_pages() so it doesn't risk misleading the caller
to think pages have been allocated when they actually haven't
- Fix direct-io folio offset and length calculation
netfs:
- Fix async direct-io handling
- Fix read-retry for filesystems that don't provide a
->prepare_read() method
vfs:
- Prevent truncating 64-bit offsets to 32-bits in iomap
- Fix memory barrier interactions when polling
- Remove MNT_ONRB to fix concurrent modification of @mnt->mnt_flags
leading to MNT_ONRB to not be raised and invalid access to a list
member"
* tag 'vfs-6.13-rc7.fixes.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
poll: kill poll_does_not_wait()
sock_poll_wait: kill the no longer necessary barrier after poll_wait()
io_uring_poll: kill the no longer necessary barrier after poll_wait()
poll_wait: kill the obsolete wait_address check
poll_wait: add mb() to fix theoretical race between waitqueue_active() and .poll()
afs: Fix merge preference rule failure condition
netfs: Fix read-retry for fs with no ->prepare_read()
netfs: Fix kernel async DIO
fs: kill MNT_ONRB
iomap: avoid avoid truncating 64-bit offset to 32 bits
afs: Fix the maximum cell name length
fuse: Set *nbytesp=0 in fuse_get_user_pages on allocation failure
fuse: fix direct io folio offset and length calculation
|
|
The snd_hdac_adsp_xxx() wrap snd_hdac_reg_xxx() helpers to simplify
register access for AudioDSP drivers e.g.: the avs-driver. Byte- and
word-variants of said helps do not expand to bare readx/writex()
operations but functions instead and, due to pointer type
incompatibility, cause compilation to fail.
As the macros are utilized by the avs-driver alone, relocate the code
introduced with commit c19bd02e9029 ("ALSA: hda: Add helper macros for
DSP capable devices") into the avs/ directory and update it to operate
on 'adev' i.e.: the avs-driver-context directly to fix the issue.
Fixes: c19bd02e9029 ("ALSA: hda: Add helper macros for DSP capable devices")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20250110113326.3809897-2-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes for !REGULATOR and !OF configurations, adding
missing stubs"
* tag 'regulator-fix-v6.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Move OF_ API declarations/definitions outside CONFIG_REGULATOR
regulator: Guard of_regulator_bulk_get_all() with CONFIG_OF
|
|
In the SPI-NAND layer, we currently make list of operation variants from
the fastest one to the slowest and there is a bit of logic in the core
to go over them and pick the first one that is supported by the
controller, ie. the fastest one among the supported ops.
This kind of logic only works if all operations run at the same
frequency, but as soon as we introduce per operation max frequencies it
is not longer as obvious which operation will be faster, especially
since it also depends on the PCB/controller frequency limitation.
One way to make this choice more clever is to go over all the
variants and for each of them derive an indicator which will help derive
the theoretical best. In this case, we derive a theoretical duration for
the entire operation and we take the smallest one.
Add a helper that parses the spi-mem operation and returns this value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250110-winbond-6-11-rc1-quad-support-v3-20-7ab4bd56cf6e@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a helper that freezes the queue, updates the queue limits and
unfreezes the queue and convert all open coded versions of that to the
new helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
queue_limits_commit_update is the function that needs to operate on a
frozen queue, not queue_limits_start_update. Update the kerneldoc
comments to reflect that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Make /afs/@cell a symlink in the /afs dynamic root to match what other AFS
clients do rather than doing a substitution in the dentry name. This has
the bonus of being tab-expandable also.
Further, provide a /afs/.@cell symlink to point to the dotted cell share.
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20250107183454.608451-4-dhowells@redhat.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Bring in the fixes for __pollwait() and waitqueue_active() interactions.
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
It no longer has users.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250107162743.GA18947@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Now that poll_wait() provides a full barrier we can remove smp_mb() from
sock_poll_wait().
Also, the poll_does_not_wait() check before poll_wait() just adds the
unnecessary confusion, kill it. poll_wait() does the same "p && p->_qproc"
check.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250107162736.GA18944@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
This check is historical and no longer needed, wait_address is never NULL.
These days we rely on the poll_table->_qproc check. NULL if select/poll
is not going to sleep, or it already has a data to report, or all waiters
have already been registered after the 1st iteration.
However, poll_table *p can be NULL, see p9_fd_poll() for example, so we
can't remove the "p != NULL" check.
Link: https://lore.kernel.org/all/20250106180325.GF7233@redhat.com/
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250107162724.GA18926@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
.poll()
As the comment above waitqueue_active() explains, it can only be used
if both waker and waiter have mb()'s that pair with each other. However
__pollwait() is broken in this respect.
This is not pipe-specific, but let's look at pipe_poll() for example:
poll_wait(...); // -> __pollwait() -> add_wait_queue()
LOAD(pipe->head);
LOAD(pipe->head);
In theory these LOAD()'s can leak into the critical section inside
add_wait_queue() and can happen before list_add(entry, wq_head), in this
case pipe_poll() can race with wakeup_pipe_readers/writers which do
smp_mb();
if (waitqueue_active(wq_head))
wake_up_interruptible(wq_head);
There are more __pollwait()-like functions (grep init_poll_funcptr), and
it seems that at least ep_ptable_queue_proc() has the same problem, so the
patch adds smp_mb() into poll_wait().
Link: https://lore.kernel.org/all/20250102163320.GA17691@redhat.com/
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250107162717.GA18922@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
ipsec-next-2025-01-09
1) Implement the AGGFRAG protocol and basic IP-TFS (RFC9347) functionality.
From Christian Hopps.
2) Support ESN context update to hardware for TX.
From Jianbo Liu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 493454445c95 ("drm/xe: switch to common PCI ID macros") removed
xe_pciids.h via drm-intel-next. In the mean time, commit ae78ec0a52c4
("drm/xe/ptl: Add another PTL PCI ID") added to xe_pciids.h via
drm-xe-next.
The two commits were merged in commit 8f109f287fdc ("Merge drm/drm-next
into drm-xe-next"), but xe_pciids.h wasn't removed, and the PCI ID
wasn't added to pciids.h.
Remove xe_pciids.h, and add the PCI ID to pciids.h.
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: 8f109f287fdc ("Merge drm/drm-next into drm-xe-next")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/r/20241125120921.1bbc1930@canb.auug.org.au
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109105032.2585416-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
cgroup resource allocation has to be handled in TTM, so -EAGAIN from
cgroups can be converted into -ENOSPC, and the limitcg can be properly
evicted in ttm code.
When hitting a resource limit through -EAGAIN, the cgroup for which the
limit is hit is also returned. This allows eviction to delete only from
cgroups which are a subgroup of the current cgroup.
The returned CSS is used to determine if eviction is valuable for a
given resource, and allows TTM to only target specific resources to
lower memory usage.
Co-developed-by: Friedrich Vock <friedrich.vock@gmx.de>
Signed-off-by: Friedrich Vock <friedrich.vock@gmx.de>
Co-developed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20241204134410.1161769-4-dev@lankhorst.se
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
This backmerges Linux 6.13-rc6 this is need for the newer pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Remove all hyperv-tlfs.h files. These are no longer included
anywhere. hyperv/hvhdk.h serves the same role, but with an easier
path for adding new definitions.
Remove the relevant lines in MAINTAINERS.
Signed-off-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Link: https://lore.kernel.org/r/1732577084-2122-6-git-send-email-nunodasneves@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1732577084-2122-6-git-send-email-nunodasneves@linux.microsoft.com>
|
|
Switch to using hvhdk.h everywhere in the kernel. This header
includes all the new Hyper-V headers in include/hyperv, which form a
superset of the definitions found in hyperv-tlfs.h.
This makes it easier to add new Hyper-V interfaces without being
restricted to those in the TLFS doc (reflected in hyperv-tlfs.h).
To be more consistent with the original Hyper-V code, the names of
some definitions are changed slightly. Update those where needed.
Update comments in mshyperv.h files to point to include/hyperv for
adding new definitions.
Signed-off-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Link: https://lore.kernel.org/r/1732577084-2122-5-git-send-email-nunodasneves@linux.microsoft.com
Link: https://lore.kernel.org/r/20250108222138.1623703-3-romank@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
