| Age | Commit message (Collapse) | Author |
|---|
|
The netpoll_rx_disable() will always return 0, it is no use and looks wordy,
so remove the unnecessary code and get rid of it in _dev_open and _dev_close.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.
The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.
SKB Usage:
When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:
* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
skb->inner_protocol is added by this patch.
* Set skb->protocol to the new MPLS ethertype of the packet.
* Set skb->network_header to correspond to the
end of the L3 header, including the MPLS label stack.
I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code. The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.
Features:
I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols. Jesse, I understand that
you have some ideas here. I am more than happy to change my implementation.
This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.
A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload. Currently no devices support this
and MPLS GSO always falls back to software.
Alternate Implementation:
One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().
I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.
MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.
Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The FTP conntrack code currently only accepts the following format for
the 227 response for PASV:
227 Entering Passive Mode (148,100,81,40,31,161).
It doesn't accept the following format from an obscure server:
227 Data transfer will passively listen to 67,218,99,134,50,144
From RFC 1123:
The format of the 227 reply to a PASV command is not
well standardized. In particular, an FTP client cannot
assume that the parentheses shown on page 40 of RFC-959
will be present (and in fact, Figure 3 on page 43 omits
them). Therefore, a User-FTP program that interprets
the PASV reply must scan the reply for the first digit
of the host and port numbers.
This patch adds support for the RFC 1123 clarification by:
- Allowing a search filter to specify NUL as the terminator so that
try_number will return successfully if the array of numbers has been
filled when an unexpected character is encountered.
- Using space as the separator for the 227 reply and then scanning for
the first digit of the number sequence. The number sequence is parsed
out using the existing try_rfc959 but with a NUL terminator.
References: https://bugzilla.novell.com/show_bug.cgi?id=466279
References: http://bugzilla.netfilter.org/show_bug.cgi?id=574
Reported-by: Mark Post <mpost@novell.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netfilter-devel@vger.kernel.org
Cc: netfilter@vger.kernel.org
Cc: coreteam@netfilter.org
Cc: netdev@vger.kernel.org
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Expire cached connection for new TCP/SCTP connection if real
server is down. Otherwise, IPVS uses the dead server for the
reused connection, instead of a new working one.
Signed-off-by: Grzegorz Lyczba <grzegorz.lyczba@gmail.com>
Acked-by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.
Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The portid is set to NETLINK_CB(skb).portid at create time.
The run-time check will always be false.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix SETCLIENTID fallback if GSS is not available
SUNRPC: Prevent an rpc_task wakeup race
NFSv4.1 Fix a pNFS session draining deadlock
SUNRPC: Convert auth_gss pipe detection to work in namespaces
SUNRPC: Faster detection if gssd is actually running
SUNRPC: Fix a bug in gss_create_upcall
|
|
Daniel Petre reported crashes in icmp_dst_unreach() with following call
graph:
#3 [ffff88003fc03938] __stack_chk_fail at ffffffff81037f77
#4 [ffff88003fc03948] icmp_send at ffffffff814d5fec
#5 [ffff88003fc03ae8] ipv4_link_failure at ffffffff814a1795
#6 [ffff88003fc03af8] ipgre_tunnel_xmit at ffffffff814e7965
#7 [ffff88003fc03b78] dev_hard_start_xmit at ffffffff8146e032
#8 [ffff88003fc03bc8] sch_direct_xmit at ffffffff81487d66
#9 [ffff88003fc03c08] __qdisc_run at ffffffff81487efd
#10 [ffff88003fc03c48] dev_queue_xmit at ffffffff8146e5a7
#11 [ffff88003fc03c88] ip_finish_output at ffffffff814ab596
Daniel found a similar problem mentioned in
http://lkml.indiana.edu/hypermail/linux/kernel/1007.0/00961.html
And indeed this is the root cause : skb->cb[] contains data fooling IP
stack.
We must clear IPCB in ip_tunnel_xmit() sooner in case dst_link_failure()
is called. Or else skb->cb[] might contain garbage from GSO segmentation
layer.
A similar fix was tested on linux-3.9, but gre code was refactored in
linux-3.10. I'll send patches for stable kernels as well.
Many thanks to Daniel for providing reports, patches and testing !
Reported-by: Daniel Petre <daniel.petre@rcs-rds.ro>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
case TCP_FIN_WAIT1 can also be simplified by reversing tests
and adding breaks;
Add braces after case and move automatic definitions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
case TCP_SYN_RECV: can have another indentation level removed
by converting
if (acceptable) {
...;
} else {
return 1;
}
to
if (!acceptable)
return 1;
...;
Reflow code and comments to fit 80 columns.
Another pure cleanup patch.
Signed-off-by: Joe Perches <joe@perches.com>
Improved-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove one level of indentation 'introduced' in commit
c3ae62af8e75 (tcp: should drop incoming frames without ACK flag set)
if (true) {
...
}
@acceptable variable is a boolean.
This patch is a pure cleanup.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now when upper device is changed, event is not propagated via RT Netlink
to userspace. Userspace might never now about the change. Fix this by
adding upper-device-change notifier event.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.
Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.
Caveats:
- Setting options via ancillary data (e.g., using IPV6_PKTINFO
to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
properly.
Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This member of struct netns_ipvs is calculated from nr_free_buffer_pages
so change its type to unsigned long in case of overflow. Also, type of
its related proc var sync_qlen_max and the return type of function
sysctl_sync_qlen_max() should be changed to unsigned long, too.
Besides, the type of ipvs_master_sync_state->sync_queue_len should be
changed to unsigned long accordingly.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The reg_mutex is similar to the ones I just removed in
cfg80211 but even less useful since it protects global
data, and we hold the RTNL in all places (except module
unload) already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since it just does a quick check of the last regulatory
request, the function doesn't have to hold the reg mutex
but can use RCU instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the driver for some reason successfully finishes
scanning while in p2p_stop_device(), cfg80211 will
still set it to aborted. Simplify this code using the
new 'notified' value and only mark it aborted in case
the driver didn't notify cfg80211 at all (in which
case we also leak the request to not crash, this is
a driver bug.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to lock, we can just use an atomic_t.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function is only used and needed by the wext code
for scanning, so move it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Move mandatory rates calculation to cfg80211, shared with non mac80211 drivers.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[extend documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As estab_plinks is not a statistics member, don't show its debug information
along with other mesh stat members
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
|
|
Some chips can tell us if received frame was
encoded with STBC or not. To make this information available
in user space we can use updated radiotap specification:
http://www.radiotap.org/defined-fields/MCS
This patch will set number of STBC encoded spatial streams (Nss).
The HAVE_STBC flag should be provided by driver.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When vlan device is configured on top of the brige, it does
not support any offload capabilities because the bridge
device does not initiliaze vlan_fatures. Set vlan_fatures to
be equivalent to hw_fatures.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 3853b5841c01a ("xps: Improvements in TX queue selection")
introduced ooo_okay flag, but the condition to set it is slightly wrong.
In our traces, we have seen ACK packets being received out of order,
and RST packets sent in response.
We should test if we have any packets still in host queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If nf_log uses ipt_ULOG as logging output, we can deliver non-null
terminated strings to user-space since the maximum length of the
prefix that is passed by nf_log is NF_LOG_PREFIXLEN but pm->prefix
is 32 bytes long (ULOG_PREFIX_LEN).
This is actually happening already from nf_conntrack_tcp if ipt_ULOG
is used, since it is passing strings longer than 32 bytes.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This avoids the situation where walking of a large number of connections
may prevent scheduling for a long time while also avoiding excessive
calls to rcu_read_unlock() and rcu_read_lock().
Note that in the case of !CONFIG_PREEMPT_RCU this will
add a call to cond_resched().
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This target has been superseded by NFLOG. Spot a warning
so we prepare removal in a couple of years.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
|
|
Don't panic if we hit an error while adding the nf_log or pernet
netfilter support, just bail out.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
|
|
Quoting https://bugzilla.netfilter.org/show_bug.cgi?id=812:
[ ip6tables -m addrtype ]
When I tried to use in the nat/PREROUTING it messes up the
routing cache even if the rule didn't matched at all.
[..]
If I remove the --limit-iface-in from the non-working scenario, so just
use the -m addrtype --dst-type LOCAL it works!
This happens when LOCAL type matching is requested with --limit-iface-in,
and the default ipv6 route is via the interface the packet we test
arrived on.
Because xt_addrtype uses ip6_route_output, the ipv6 routing implementation
creates an unwanted cached entry, and the packet won't make it to the
real/expected destination.
Silently ignoring --limit-iface-in makes the routing work but it breaks
rule matching (--dst-type LOCAL with limit-iface-in is supposed to only
match if the dst address is configured on the incoming interface;
without --limit-iface-in it will match if the address is reachable
via lo).
The test should call ipv6_chk_addr() instead. However, this would add
a link-time dependency on ipv6.
There are two possible solutions:
1) Revert the commit that moved ipt_addrtype to xt_addrtype,
and put ipv6 specific code into ip6t_addrtype.
2) add new "nf_ipv6_ops" struct to register pointers to ipv6 functions.
While the former might seem preferable, Pablo pointed out that there
are more xt modules with link-time dependeny issues regarding ipv6,
so lets go for 2).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
'name' has already set all zero when it is defined, so not need let
strncpy() to pad it again.
'name' is a string, better always let is NUL terminated, so use
strlcpy() instead of strncpy().
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
With IP early demux added in linux-3.6, we perform TCP lookup in IP
layer before iptables hooks.
We can avoid doing a second lookup in xt_socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The percpu untracked ct are not currently used for XT_CT_NOTRACK.
xt_ct_tg_check()/xt_ct_target() provides a single ct.
Thats not optimal as the ct->ct_general.use cache line will bounce among
cpus.
Use the intended [1] thing : xt_ct_target() should select the percpu
object.
[1] Refs :
commit 5bfddbd46a95c97 ("netfilter: nf_conntrack: IPS_UNTRACKED bit")
commit b3c5163fe0193a7 ("netfilter: nf_conntrack: per_cpu untracking")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The error exit path needs err explicitly set. Otherwise it
returns success and the only caller, xfrm_output_resume(),
would oops in skb_dst(skb)->ops derefence as skb_dst(skb) is
NULL.
Bug introduced in commit bb65a9cb (xfrm: removes a superfluous
check and add a statistic).
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_addr_type(&addr)&IPV6_ADDR_SCOPE_MASK could be replaced
by ipv6_addr_scope(), which is slightly faster.
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
