| Age | Commit message (Collapse) | Author |
|---|
|
Similar to xfrm6_tunnel/transport_gso_segment(), _gso_segment()
is added to do gso_segment for esp6 beet mode. Before calling
inet6_offloads[proto]->callbacks.gso_segment, it needs to do:
- Get the upper proto from ph header to get its gso_segment
when xo->proto is IPPROTO_BEETPH.
- Add SKB_GSO_TCPV6 to gso_type if x->sel.family != AF_INET6
and the proto == IPPROTO_TCP, so that the current tcp ipv6
packet can be segmented.
- Calculate a right value for skb->transport_header and move
skb->data to the transport header position.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Similar to xfrm4_tunnel/transport_gso_segment(), _gso_segment()
is added to do gso_segment for esp4 beet mode. Before calling
inet_offloads[proto]->callbacks.gso_segment, it needs to do:
- Get the upper proto from ph header to get its gso_segment
when xo->proto is IPPROTO_BEETPH.
- Add SKB_GSO_TCPV4 to gso_type if x->sel.family == AF_INET6
and the proto == IPPROTO_TCP, so that the current tcp ipv4
packet can be segmented.
- Calculate a right value for skb->transport_header and move
skb->data to the transport header position.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
devlink_nl_cmd_eswitch_set_doit() doesn't hold devlink->lock mutex while
invoking driver callback. This is likely due to eswitch mode setting
involves adding/remove devlink ports, health reporters or
other devlink objects for a devlink device.
So it is driver responsiblity to ensure thread safe eswitch state
transition happening via either sriov legacy enablement or via devlink
eswitch set callback.
Therefore, get() callback should also be invoked without holding
devlink->lock mutex.
Vendor driver can use same internal lock which it uses during eswitch
mode set() callback.
This makes get() and set() implimentation symmetric in devlink core and
in vendor drivers.
Hence, remove holding devlink->lock mutex during eswitch get() callback.
Failing to do so results into below deadlock scenario when mlx5_core
driver is improved to handle eswitch mode set critical section invoked
by devlink and sriov sysfs interface in subsequent patch.
devlink_nl_cmd_eswitch_set_doit()
mlx5_eswitch_mode_set()
mutex_lock(esw->mode_lock) <- Lock A
[...]
register_devlink_port()
mutex_lock(&devlink->lock); <- lock B
mutex_lock(&devlink->lock); <- lock B
devlink_nl_cmd_eswitch_get_doit()
mlx5_eswitch_mode_get()
mutex_lock(esw->mode_lock) <- Lock A
In subsequent patch, mlx5_core driver uses its internal lock during
get() and set() eswitch callbacks.
Other drivers have been inspected which returns either constant during
get operations or reads the value from already allocated structure.
Hence it is safe to remove the lock in get( ) callback and let vendor
driver handle it.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pull networking fixes from David Miller:
1) Fix deadlock in bpf_send_signal() from Yonghong Song.
2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.
3) Add missing locking in iwlwifi mvm code, from Avraham Stern.
4) Fix MSG_WAITALL handling in rxrpc, from David Howells.
5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
Wang.
6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.
7) cls_route removes the wrong filter during change operations, from
Cong Wang.
8) Reject unrecognized request flags in ethtool netlink code, from
Michal Kubecek.
9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
Doug Berger.
10) Don't leak ct zone template in act_ct during replace, from Paul
Blakey.
11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
Blakey.
12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
Lakkireddy.
13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
Dumazet.
14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
also from Eric Dumazet.
15) Restrict macsec to ethernet devices, from Willem de Bruijn.
16) Fix reference leak in some ethtool *_SET handlers, from Michal
Kubecek.
17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net: ena: Add PCI shutdown handler to allow safe kexec
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
selftests/net: add missing tests to Makefile
r8169: re-enable MSI on RTL8168c
net: phy: mdio-bcm-unimac: Fix clock handling
cxgb4/ptp: pass the sign of offset delta in FW CMD
net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
net: cbs: Fix software cbs to consider packet sending time
net/mlx5e: Do not recover from a non-fatal syndrome
net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
net/mlx5e: Enhance ICOSQ WQE info fields
net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
selftests: netfilter: add nfqueue test case
netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
netfilter: nft_fwd_netdev: validate family and chain type
netfilter: nft_set_rbtree: Detect partial overlaps on insertion
netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
...
|
|
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP recvmsg() calls skb_copy_datagram_iter(), which
calls an indirect function (cb pointing to simple_copy_to_iter())
for every MSS (fragment) present in the skb.
CONFIG_RETPOLINE=y forces a very expensive operation
that we can avoid thanks to indirect call wrappers.
This patch gives a 13% increase of performance on
a single flow, if the bottleneck is the thread reading
the TCP socket.
Fixes: 950fcaecd5cc ("datagram: consolidate datagram copy to iter helpers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this change, the encryption key size is not assumed to be 16 if the
read_encryption_key_size command fails for any reason. This ensures
that if the controller fails the command for any reason that the
encryption key size isn't implicitely set to 16 and instead take a more
concervative posture to assume it is 0.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add SPDX License Identifier to all .gitignore files.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new opmode notification used this attribute with a u8, when
it's documented as a u32 and indeed used in userspace as such,
it just happens to work on little-endian systems since userspace
isn't doing any strict size validation, and the u8 goes into the
lower byte. Fix this.
Cc: stable@vger.kernel.org
Fixes: 466b9936bf93 ("cfg80211: Add support to notify station's opmode change to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200325090531.be124f0a11c7.Iedbf4e197a85471ebd729b186d5365c0343bf7a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) A new selftest for nf_queue, from Florian Westphal. This test
covers two recent fixes: 07f8e4d0fddb ("tcp: also NULL skb->dev
when copy was needed") and b738a185beaa ("tcp: ensure skb->dev is
NULL before leaving TCP stack").
2) The fwd action breaks with ifb. For safety in next extensions,
make sure the fwd action only runs from ingress until it is extended
to be used from a different hook.
3) The pipapo set type now reports EEXIST in case of subrange overlaps.
Update the rbtree set to validate range overlaps, so far this
validation is only done only from userspace. From Stefano Brivio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.
The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).
Fixes: f70bb06563ed ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638ae ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.
changelog:
V2->V3:
- remove unnecessary whitespace cleanup
- add the checks if port_rate is 0 before division
V1->V2:
- combine variable "send_completed" into "last"
- add the comment for estimate of the packet sending
Fixes: 585d763af09c ("net/sched: Introduce Credit Based Shaper (CBS) qdisc")
Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set skb->tc_redirected to 1, otherwise the ifb driver drops the packet.
Set skb->tc_from_ingress to 1 to reinject the packet back to the ingress
path after leaving the ifb egress path.
This patch inconditionally sets on these two skb fields that are
meaningful to the ifb driver. The existing forward action is guaranteed
to run from ingress path.
Fixes: 39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make sure the forward action is only used from ingress.
Fixes: 39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
...and return -ENOTEMPTY to the front-end in this case, instead of
proceeding. Currently, nft takes care of checking for these cases
and not sending them to the kernel, but if we drop the set_overlap()
call in nft we can end up in situations like:
# nft add table t
# nft add set t s '{ type inet_service ; flags interval ; }'
# nft add element t s '{ 1 - 5 }'
# nft add element t s '{ 6 - 10 }'
# nft add element t s '{ 4 - 7 }'
# nft list set t s
table ip t {
set s {
type inet_service
flags interval
elements = { 1-3, 4-5, 6-7 }
}
}
This change has the primary purpose of making the behaviour
consistent with nft_set_pipapo, but is also functional to avoid
inconsistent behaviour if userspace sends overlapping elements for
any reason.
v2: When we meet the same key data in the tree, as start element while
inserting an end element, or as end element while inserting a start
element, actually check that the existing element is active, before
resetting the overlap flag (Pablo Neira Ayuso)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Replace negations of nft_rbtree_interval_end() with a new helper,
nft_rbtree_interval_start(), wherever this helps to visualise the
problem at hand, that is, for all the occurrences except for the
comparison against given flags in __nft_rbtree_get().
This gets especially useful in the next patch.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
insertion
...and return -ENOTEMPTY to the front-end on collision, -EEXIST if
an identical element already exists. Together with the previous patch,
element collision will now be returned to the user as -EEXIST.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
insertion
Currently, the -EEXIST return code of ->insert() callbacks is ambiguous: it
might indicate that a given element (including intervals) already exists as
such, or that the new element would clash with existing ones.
If identical elements already exist, the front-end is ignoring this without
returning error, in case NLM_F_EXCL is not set. However, if the new element
can't be inserted due an overlap, we should report this to the user.
To this purpose, allow set back-ends to return -ENOTEMPTY on collision with
existing elements, translate that to -EEXIST, and return that to userspace,
no matter if NLM_F_EXCL was set.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After xfrm_add_policy add a policy, its ref is 2, then
xfrm_policy_timer
read_lock
xp->walk.dead is 0
....
mod_timer()
xfrm_policy_kill
policy->walk.dead = 1
....
del_timer(&policy->timer)
xfrm_pol_put //ref is 1
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_pol_hold //ref is 1
read_unlock
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_policy_destroy is called twice, which may leads to
double free.
Call Trace:
RIP: 0010:refcount_warn_saturate+0x161/0x210
...
xfrm_policy_timer+0x522/0x600
call_timer_fn+0x1b3/0x5e0
? __xfrm_decode_session+0x2990/0x2990
? msleep+0xb0/0xb0
? _raw_spin_unlock_irq+0x24/0x40
? __xfrm_decode_session+0x2990/0x2990
? __xfrm_decode_session+0x2990/0x2990
run_timer_softirq+0x5c5/0x10e0
Fix this by use write_lock_bh in xfrm_policy_kill.
Fixes: ea2dea9dacc2 ("xfrm: remove policy lock when accessing policy->walk.dead")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4d3 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032e7 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3afea ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b305 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b83d ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that drivers explicitly register their supported packet trap groups
there is no for devlink to create them on-demand and destroy them when
their reference count reaches zero.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a place,
inet_dump_fib()
fib_table_dump
fn_trie_dump_leaf()
hlist_for_each_entry_rcu()
without rcu_read_lock() will trigger a warning,
WARNING: suspicious RCU usage
-----------------------------
net/ipv4/fib_trie.c:2216 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/1923:
#0: ffffffff8ce76e40 (rtnl_mutex){+.+.}, at: netlink_dump+0xd6/0x840
Call Trace:
dump_stack+0xa1/0xea
lockdep_rcu_suspicious+0x103/0x10d
fn_trie_dump_leaf+0x581/0x590
fib_table_dump+0x15f/0x220
inet_dump_fib+0x4ad/0x5d0
netlink_dump+0x350/0x840
__netlink_dump_start+0x315/0x3e0
rtnetlink_rcv_msg+0x4d1/0x720
netlink_rcv_skb+0xf0/0x220
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x306/0x460
netlink_sendmsg+0x44b/0x770
__sys_sendto+0x259/0x270
__x64_sys_sendto+0x80/0xa0
do_syscall_64+0x69/0xf4
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Fixes: 18a8021a7be3 ("net/ipv4: Plumb support for filtering route dumps")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 53eca1f3479f ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it's still possible for packetdrill to hang in mptcp_sendmsg(), when the
MPTCP socket falls back to regular TCP (e.g. after receiving unsupported
flags/version during the three-way handshake). Adjust MPTCP socket state
earlier, to ensure correct functionality of mptcp_sendmsg() even in case
of TCP fallback.
Fixes: 767d3ded5fb8 ("net: mptcp: don't hang before sending 'MP capable with data'")
Fixes: 1954b86016cf ("mptcp: Check connection state before attempting send")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When application uses TCP_QUEUE_SEQ socket option to
change tp->rcv_next, we must also update tp->copied_seq.
Otherwise, stuff relying on tcp_inq() being precise can
eventually be confused.
For example, tcp_zerocopy_receive() might crash because
it does not expect tcp_recv_skb() to return NULL.
We could add tests in various places to fix the issue,
or simply make sure tcp_inq() wont return a random value,
and leave fast path as it is.
Note that this fixes ioctl(fd, SIOCINQ, &val) at the same
time.
Fixes: ee9952831cfd ("tcp: Initial repair mode")
Fixes: 05255b823a61 ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checksumming
Problem:
TCP checksum in the output path is not being offloaded during GSO
in the following case:
The network driver does not support scatter-gather but supports
checksum offload with NETIF_F_HW_CSUM.
Cause:
skb_segment calls skb_copy_and_csum_bits if the network driver
does not announce NETIF_F_SG. It does not check if the driver
supports NETIF_F_HW_CSUM.
So for devices which might want to offload checksum but do not support SG
there is currently no way to do so if GSO is enabled.
Solution:
In skb_segment check if the network controller does checksum and if so
call skb_copy_bits instead of skb_copy_and_csum_bits.
Testing:
Without the patch, ran iperf TCP traffic with NETIF_F_HW_CSUM enabled
in the network driver. Observed the TCP checksum offload is not happening
since the skbs received by the driver in the output path have
skb->ip_summed set to CHECKSUM_NONE.
With the patch ran iperf TCP traffic and observed that TCP checksum
is being offloaded with skb->ip_summed set to CHECKSUM_PARTIAL.
Also tested with the patch by disabling NETIF_F_HW_CSUM in the driver
to cover the newly introduced if-else code path in skb_segment.
Link: https://lore.kernel.org/netdev/CA+FuTSeYGYr3Umij+Mezk9CUcaxYwqEe5sPSuXF8jPE2yMFJAw@mail.gmail.com
Signed-off-by: Yadu Kishore <kyk.segfault@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds bpf_sk_storage_get() and bpf_sk_storage_delete()
helper to the bpf_tcp_ca's struct_ops. That would allow
bpf-tcp-cc to:
1) share sk private data with other bpf progs.
2) use bpf_sk_storage as a private storage for a bpf-tcp-cc
if the existing icsk_ca_priv is not big enough.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200320152101.2169498-1-kafai@fb.com
|
|
When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Make it so that CEPH_MSG_DATA_PAGES data item can own pages,
fixing a bunch of memory leaks for a page vector allocated in
alloc_msg_with_page_vector(). Currently, only watch-notify
messages trigger this allocation, and normally the page vector
is freed either in handle_watch_notify() or by the caller of
ceph_osdc_notify(). But if the message is freed before that
(e.g. if the session faults while reading in the message or
if the notify is stale), we leak the page vector.
This was supposed to be fixed by switching to a message-owned
pagelist, but that never happened.
Fixes: 1907920324f1 ("libceph: support for sending notifies")
Reported-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Roman Penyaev <rpenyaev@suse.de>
|
|
CEPH_OSDMAP_FULL/NEARFULL aren't set since mimic, so we need to consult
per-pool flags as well. Unfortunately the backwards compatibility here
is lacking:
- the change that deprecated OSDMAP_FULL/NEARFULL went into mimic, but
was guarded by require_osd_release >= RELEASE_LUMINOUS
- it was subsequently backported to luminous in v12.2.2, but that makes
no difference to clients that only check OSDMAP_FULL/NEARFULL because
require_osd_release is not client-facing -- it is for OSDs
Since all kernels are affected, the best we can do here is just start
checking both map flags and pool flags and send that to stable.
These checks are best effort, so take osdc->lock and look up pool flags
just once. Remove the FIXME, since filesystem quotas are checked above
and RADOS quotas are reflected in POOL_FLAG_FULL: when the pool reaches
its quota, both POOL_FLAG_FULL and POOL_FLAG_FULL_QUOTA are set.
Cc: stable@vger.kernel.org
Reported-by: Yanhu Cao <gmayyyha@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Acked-by: Sage Weil <sage@redhat.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
net/mptcp/options.c: In function 'mptcp_established_options_dss':
net/mptcp/options.c:338:7: warning:
variable 'can_ack' set but not used [-Wunused-but-set-variable]
commit dc093db5cc05 ("mptcp: drop unneeded checks")
leave behind this unused, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sockmap performs lockless writes to sk->sk_prot on the following paths:
tcp_bpf_{recvmsg|sendmsg} / sock_map_unref
sk_psock_put
sk_psock_drop
sk_psock_restore_proto
WRITE_ONCE(sk->sk_prot, proto)
To prevent load/store tearing [1], and to make tooling aware of intentional
shared access [2], we need to annotate other sites that access sk_prot with
READ_ONCE/WRITE_ONCE macros.
Change done with Coccinelle with following semantic patch:
@@
expression E;
identifier I;
struct sock *sk;
identifier sk_prot =~ "^sk_prot$";
@@
(
E =
-sk->sk_prot
+READ_ONCE(sk->sk_prot)
|
-sk->sk_prot = E
+WRITE_ONCE(sk->sk_prot, E)
|
-sk->sk_prot
+READ_ONCE(sk->sk_prot)
->I
)
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apart from being a "tremendous" win when it comes to generated machine
code (see bloat-o-meter output for x86-64 below) this mainly prepares
ground for annotating access to sk_prot with READ_ONCE, so that we don't
pepper the code with access annotations and needlessly repeat loads.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-46 (-46)
Function old new delta
tls_init 851 805 -46
Total: Before=21063, After=21017, chg -0.22%
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The helper that builds kTLS proto ops doesn't need to and should not modify
the base proto ops. Annotate the parameter as read-only.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull io_uring fixes from Jens Axboe:
"Two different fixes in here:
- Fix for a potential NULL pointer deref for links with async or
drain marked (Pavel)
- Fix for not properly checking RLIMIT_NOFILE for async punted
operations.
This affects openat/openat2, which were added this cycle, and
accept4. I did a full audit of other cases where we might check
current->signal->rlim[] and found only RLIMIT_FSIZE for buffered
writes and fallocate. That one is fixed and queued for 5.7 and
marked stable"
* tag 'io_uring-5.6-20200320' of git://git.kernel.dk/linux-block:
io_uring: make sure accept honor rlimit nofile
io_uring: make sure openat/openat2 honor rlimit nofile
io_uring: NULL-deref for IOSQE_{ASYNC,DRAIN}
|
|
In rare cases retransmit logic will make a full skb copy, which will not
trigger the zeroing added in recent change
b738a185beaa ("tcp: ensure skb->dev is NULL before leaving TCP stack").
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 75c119afe14f ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac94 ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Refetch IP header pointer after pskb_may_pull() in flowtable,
from Haishuang Yan.
2) Fix memleak in flowtable offload in nf_flow_table_free(),
from Paul Blakey.
3) Set control.addr_type mask in flowtable offload, from Edward Cree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes:
* HE ranging (fine timing measurement) API support
* hwsim gets virtio support, for use with wmediumd,
to be able to simulate with multiple machines
* eapol-over-nl80211 improvements to exclude preauth
* IBSS reset support, to recover connections from
userspace
* and various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have a nested tunnel info attribute we can add a separate
one for the tunnel command and require it explicitly from user-space. It
must be one of RTM_SETLINK/DELLINK. Only RTM_SETLINK requires a valid
tunnel id, DELLINK just removes it if it was set before. This allows us
to have all tunnel attributes and control in one place, thus removing
the need for an outside vlan info flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
