summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2020-03-08Bluetooth: Enable erroneous data reporting if WBS is supportedAlain Michaud
This change introduces a wide band speech setting which allows higher level clients to query the local controller support for wide band speech as well as set the setting state when the radio is powered off. Internally, this setting controls if erroneous data reporting is enabled on the controller. Signed-off-by: Alain Michaud <alainm@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-03-08Bluetooth: Make use of skb_pull to parse L2CAP signaling PDUsLuiz Augusto von Dentz
This uses skb_pull when parsing signalling PDUs so skb->data for pointing to the current PDU and skb->len as the remaining bytes to be processed. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-03-07Bluetooth: Fix calculation of SCO handle for packet processingMarcel Holtmann
When processing SCO packets, the handle is wrongly assumed as 16-bit value. The actual size is 12-bits and the other 4-bits are used for packet flags. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2020-03-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Patches to bump position index from sysctl seq_next, from Vasilin Averin. 2) Release flowtable hook from error path, from Florian Westphal. 3) Patches to add missing netlink attribute validation, from Jakub Kicinski. 4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info(). 5) Infinite loop in module autoload if extension is not available, from Florian Westphal. 6) Missing module ownership in inet/nat chain type definition. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-06netfilter: nft_chain_nat: inet family is missing module ownershipPablo Neira Ayuso
Set owner to THIS_MODULE, otherwise the nft_chain_nat module might be removed while there are still inet/nat chains in place. [ 117.942096] BUG: unable to handle page fault for address: ffffffffa0d5e040 [ 117.942101] #PF: supervisor read access in kernel mode [ 117.942103] #PF: error_code(0x0000) - not-present page [ 117.942106] PGD 200c067 P4D 200c067 PUD 200d063 PMD 3dc909067 PTE 0 [ 117.942113] Oops: 0000 [#1] PREEMPT SMP PTI [ 117.942118] CPU: 3 PID: 27 Comm: kworker/3:0 Not tainted 5.6.0-rc3+ #348 [ 117.942133] Workqueue: events nf_tables_trans_destroy_work [nf_tables] [ 117.942145] RIP: 0010:nf_tables_chain_destroy.isra.0+0x94/0x15a [nf_tables] [ 117.942149] Code: f6 45 54 01 0f 84 d1 00 00 00 80 3b 05 74 44 48 8b 75 e8 48 c7 c7 72 be de a0 e8 56 e6 2d e0 48 8b 45 e8 48 c7 c7 7f be de a0 <48> 8b 30 e8 43 e6 2d e0 48 8b 45 e8 48 8b 40 10 48 85 c0 74 5b 8b [ 117.942152] RSP: 0018:ffffc9000015be10 EFLAGS: 00010292 [ 117.942155] RAX: ffffffffa0d5e040 RBX: ffff88840be87fc2 RCX: 0000000000000007 [ 117.942158] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffffffffa0debe7f [ 117.942160] RBP: ffff888403b54b50 R08: 0000000000001482 R09: 0000000000000004 [ 117.942162] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8883eda7e540 [ 117.942164] R13: dead000000000122 R14: dead000000000100 R15: ffff888403b3db80 [ 117.942167] FS: 0000000000000000(0000) GS:ffff88840e4c0000(0000) knlGS:0000000000000000 [ 117.942169] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 117.942172] CR2: ffffffffa0d5e040 CR3: 00000003e4c52002 CR4: 00000000001606e0 [ 117.942174] Call Trace: [ 117.942188] nf_tables_trans_destroy_work.cold+0xd/0x12 [nf_tables] [ 117.942196] process_one_work+0x1d6/0x3b0 [ 117.942200] worker_thread+0x45/0x3c0 [ 117.942203] ? process_one_work+0x3b0/0x3b0 [ 117.942210] kthread+0x112/0x130 [ 117.942214] ? kthread_create_worker_on_cpu+0x40/0x40 [ 117.942221] ret_from_fork+0x35/0x40 nf_tables_chain_destroy() crashes on module_put() because the module is gone. Fixes: d164385ec572 ("netfilter: nat: add inet family nat support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-05mptcp: always include dack if possible.Paolo Abeni
Currently passive MPTCP socket can skip including the DACK option - if the peer sends data before accept() completes. The above happens because the msk 'can_ack' flag is set only after the accept() call. Such missing DACK option may cause - as per RFC spec - unwanted fallback to TCP. This change addresses the issue using the key material available in the current subflow, if any, to create a suitable dack option when msk ack seq is not yet available. v1 -> v2: - adavance the generated ack after the initial MPC packet Fixes: d22f4988ffec ("mptcp: process MP_CAPABLE data option") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05net: nfc: fix bounds checking bugs on "pipe"Dan Carpenter
This is similar to commit 674d9de02aa7 ("NFC: Fix possible memory corruption when handling SHDLC I-Frame commands") and commit d7ee81ad09f0 ("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which added range checks on "pipe". The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work(). It's in the 0-255 range. We're using it as the array index into the hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members. Fixes: 118278f20aa8 ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05net: sched: Make FIFO Qdisc offloadablePetr Machata
Invoke ndo_setup_tc() as appropriate to signal init / replacement, destroying and dumping of pFIFO / bFIFO Qdisc. A lot of the FIFO logic is used for pFIFO_head_drop as well, but that's a semantically very different Qdisc that isn't really in the same boat as pFIFO / bFIFO. Split some of the functions to keep the Qdisc intact. Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05ethtool: add infrastructure for centralized checking of coalescing parametersJakub Kicinski
Linux supports 22 different interrupt coalescing parameters. No driver implements them all. Some drivers just ignore the ones they don't support, while others have to carry a long list of checks to reject unsupported settings. To simplify the drivers add the ability to specify inside ethtool_ops which parameters are supported and let the core reject attempts to set any other one. This commit makes the mechanism an opt-in, only drivers which set ethtool_opts->coalesce_types to a non-zero value will have the checks enforced. The same mask is used for global and per queue settings. v3: - move the (temporary) check if driver defines types earlier (Michal) - rename used_types -> nonzero_params, and coalesce_types -> supported_coalesce_params (Alex) - use EOPNOTSUPP instead of EINVAL (Andrew, Michal) Leaving the long series of ifs for now, it seems nice to be able to grep for the field and flag names. This will probably have to be revisited once netlink support lands. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05hsr: fix refcnt leak of hsr slave interfaceTaehee Yoo
In the commit e0a4b99773d3 ("hsr: use upper/lower device infrastructure"), dev_get() was removed but dev_put() in the error path wasn't removed. So, if creating hsr interface command is failed, the reference counter leak of lower interface would occur. Test commands: ip link add dummy0 type dummy ip link add ipvlan0 link dummy0 type ipvlan mode l2 ip link add ipvlan1 link dummy0 type ipvlan mode l2 ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1 ip link del ipvlan0 Result: [ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1 Fixes: e0a4b99773d3 ("hsr: use upper/lower device infrastructure") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05netfilter: nf_tables: fix infinite loop when expr is not availableFlorian Westphal
nft will loop forever if the kernel doesn't support an expression: 1. nft_expr_type_get() appends the family specific name to the module list. 2. -EAGAIN is returned to nfnetlink, nfnetlink calls abort path. 3. abort path sets ->done to true and calls request_module for the expression. 4. nfnetlink replays the batch, we end up in nft_expr_type_get() again. 5. nft_expr_type_get attempts to append family-specific name. This one already exists on the list, so we continue 6. nft_expr_type_get adds the generic expression name to the module list. -EAGAIN is returned, nfnetlink calls abort path. 7. abort path encounters the family-specific expression which has 'done' set, so it gets removed. 8. abort path requests the generic expression name, sets done to true. 9. batch is replayed. If the expression could not be loaded, then we will end up back at 1), because the family-specific name got removed and the cycle starts again. Note that userspace can SIGKILL the nft process to stop the cycle, but the desired behaviour is to return an error after the generic expr name fails to load the expression. Fixes: eb014de4fd418 ("netfilter: nf_tables: autoload modules from the abort path") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-05netfilter: nf_tables: dump NFTA_CHAIN_FLAGS attributePablo Neira Ayuso
Missing NFTA_CHAIN_FLAGS netlink attribute when dumping basechain definitions. Fixes: c9626a2cbdb2 ("netfilter: nf_tables: add hardware offload support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04net: mscc: ocelot: eliminate confusion between CPU and NPI portVladimir Oltean
Ocelot has the concept of a CPU port. The CPU port is represented in the forwarding and the queueing system, but it is not a physical device. The CPU port can either be accessed via register-based injection/extraction (which is the case of Ocelot), via Frame-DMA (similar to the first one), or "connected" to a physical Ethernet port (called NPI in the datasheet) which is the case of the Felix DSA switch. In Ocelot the CPU port is at index 11. In Felix the CPU port is at index 6. The CPU bit is treated special in the forwarding, as it is never cleared from the forwarding port mask (once added to it). Other than that, it is treated the same as a normal front port. Both Felix and Ocelot should use the CPU port in the same way. This means that Felix should not use the NPI port directly when forwarding to the CPU, but instead use the CPU port. This patch is fixing this such that Felix will use port 6 as its CPU port, and just use the NPI port to carry the traffic. Therefore, eliminate the "ocelot->cpu" variable which was holding the index of the NPI port for Felix, and the index of the CPU port module for Ocelot, so the variable was actually configuring different things for different drivers and causing at least part of the confusion. Also remove the "ocelot->num_cpu_ports" variable, which is the result of another confusion. The 2 CPU ports mentioned in the datasheet are because there are two frame extraction channels (register based or DMA based). This is of no relevance to the driver at the moment, and invisible to the analyzer module. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04bpf: Add selftests for BPF_MODIFY_RETURNKP Singh
Test for two scenarios: * When the fmod_ret program returns 0, the original function should be called along with fentry and fexit programs. * When the fmod_ret program returns a non-zero value, the original function should not be called, no side effect should be observed and fentry and fexit programs should be called. The result from the kernel function call and whether a side-effect is observed is returned via the retval attr of the BPF_PROG_TEST_RUN (bpf) syscall. Signed-off-by: KP Singh <kpsingh@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200304191853.1529-8-kpsingh@chromium.org
2020-03-04bpf: Add test ops for BPF_PROG_TYPE_TRACINGKP Singh
The current fexit and fentry tests rely on a different program to exercise the functions they attach to. Instead of doing this, implement the test operations for tracing which will also be used for BPF_MODIFY_RETURN in a subsequent patch. Also, clean up the fexit test to use the generated skeleton. Signed-off-by: KP Singh <kpsingh@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200304191853.1529-7-kpsingh@chromium.org
2020-03-04pie: remove pie_vars->accu_prob_overflowsLeslie Monis
The variable pie_vars->accu_prob is used as an accumulator for probability values. Since probabilty values are scaled using the MAX_PROB macro denoting (2^64 - 1), pie_vars->accu_prob is likely to overflow as it is of type u64. The variable pie_vars->accu_prob_overflows counts the number of times the variable pie_vars->accu_prob overflows. The MAX_PROB macro needs to be equal to at least (2^39 - 1) in order to do precise calculations without any underflow. Thus MAX_PROB can be reduced to (2^56 - 1) without affecting the precision in calculations drastically. Doing so will eliminate the need for the variable pie_vars->accu_prob_overflows as the variable pie_vars->accu_prob will never overflow. Removing the variable pie_vars->accu_prob_overflows also reduces the size of the structure pie_vars to exactly 64 bytes. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04pie: remove unnecessary type castingLeslie Monis
In function pie_calculate_probability(), the variables alpha and beta are of type u64. The variables qdelay, qdelay_old and params->target are of type psched_time_t (which is also u64). The explicit type casting done when calculating the value for the variable delta is redundant and not required. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04pie: use term backlog instead of qlenLeslie Monis
Remove ambiguity by using the term backlog instead of qlen when representing the queue length in bytes. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04net/sched: act_ct: Use pskb_network_may_pull()Paul Blakey
To make the filler functions more generic, use network relative skb pulling. Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04net/sched: act_ct: Fix ipv6 lookup of offloaded connectionsPaul Blakey
When checking the protocol number tcf_ct_flow_table_lookup() handles the flow as if it's always ipv4, while it can be ipv6. Instead, refactor the code to fetch the tcp header, if available, in the relevant family (ipv4/ipv6) filler function, and do the check on the returned tcp header. Fixes: 46475bb20f4b ("net/sched: act_ct: Software offload of established flows") Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04esp: remove the skb from the chain when it's enqueued in cryptd_wqXin Long
Xiumei found a panic in esp offload: BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 RIP: 0010:esp_output_done+0x101/0x160 [esp4] Call Trace: ? esp_output+0x180/0x180 [esp4] cryptd_aead_crypt+0x4c/0x90 cryptd_queue_worker+0x6e/0xa0 process_one_work+0x1a7/0x3b0 worker_thread+0x30/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x35/0x40 It was caused by that skb secpath is used in esp_output_done() after it's been released elsewhere. The tx path for esp offload is: __dev_queue_xmit()-> validate_xmit_skb_list()-> validate_xmit_xfrm()-> esp_xmit()-> esp_output_tail()-> aead_request_set_callback(esp_output_done) <--[1] crypto_aead_encrypt() <--[2] In [1], .callback is set, and in [2] it will trigger the worker schedule, later on a kernel thread will call .callback(esp_output_done), as the call trace shows. But in validate_xmit_xfrm(): skb_list_walk_safe(skb, skb2, nskb) { ... err = x->type_offload->xmit(x, skb2, esp_features); [esp_xmit] ... } When the err is -EINPROGRESS, which means this skb2 will be enqueued and later gets encrypted and sent out by .callback later in a kernel thread, skb2 should be removed fromt skb chain. Otherwise, it will get processed again outside validate_xmit_xfrm(), which could release skb secpath, and cause the panic above. This patch is to remove the skb from the chain when it's enqueued in cryptd_wq. While at it, remove the unnecessary 'if (!skb)' check. Fixes: 3dca3f38cfb8 ("xfrm: Separate ESP handling from segmentation for GRO packets.") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2020-03-04Bluetooth: guard against controllers sending zero'd eventsAlain Michaud
Some controllers have been observed to send zero'd events under some conditions. This change guards against this condition as well as adding a trace to facilitate diagnosability of this condition. Signed-off-by: Alain Michaud <alainm@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-03-03net: dsa: Add bypass operations for the flower classifier-action filterVladimir Oltean
Due to the immense variety of classification keys and actions available for tc-flower, as well as due to potentially very different DSA switch capabilities, it doesn't make a lot of sense for the DSA mid layer to even attempt to interpret these. So just pass them on to the underlying switch driver. DSA implements just the standard boilerplate for binding and unbinding flow blocks to ports, since nobody wants to deal with that. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: qrtr: Fix FIXME related to qrtr_ns_init()Bjorn Andersson
The 2 second delay before calling qrtr_ns_init() meant that the remote processors would register as endpoints in qrtr and the say_hello() call would therefor broadcast the outgoing HELLO to them. With the HELLO handshake corrected this delay is no longer needed. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: qrtr: Respond to HELLO messageBjorn Andersson
Lost in the translation from the user space implementation was the detail that HELLO mesages must be exchanged between each node pair. As such the incoming HELLO must be replied to. Similar to the previous implementation no effort is made to prevent two Linux boxes from continuously sending HELLO messages back and forth, this is left to a follow up patch. say_hello() is moved, to facilitate the new call site. Fixes: 0c2204a4ad71 ("net: qrtr: Migrate nameservice to kernel from userspace") Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04netfilter: nft_tunnel: add missing attribute validation for tunnelsJakub Kicinski
Add missing attribute validation for tunnel source and destination ports to the netlink policy. Fixes: af308b94a2a4 ("netfilter: nf_tables: add tunnel support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nft_payload: add missing attribute validation for payload csum flagsJakub Kicinski
Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS to the netlink policy. Fixes: 1814096980bb ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: cthelper: add missing attribute validation for cthelperJakub Kicinski
Add missing attribute validation for cthelper to the netlink policy. Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nf_tables: free flowtable hooks on hook register errorFlorian Westphal
If hook registration fails, the hooks allocated via nft_netdev_hook_alloc need to be freed. We can't change the goto label to 'goto 5' -- while it does fix the memleak it does cause a warning splat from the netfilter core (the hooks were not registered). Fixes: 3f0465a9ef02 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables") Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: x_tables: xt_mttg_seq_next should increase position indexVasily Averin
If .next function does not change position index, following .show function will repeat output related to current position index. Without patch: # dd if=/proc/net/ip_tables_matches # original file output conntrack conntrack conntrack recent recent icmp udplite udp tcp 0+1 records in 0+1 records out 65 bytes copied, 5.4074e-05 s, 1.2 MB/s # dd if=/proc/net/ip_tables_matches bs=62 skip=1 dd: /proc/net/ip_tables_matches: cannot skip to specified offset cp <<< end of last line tcp <<< and then unexpected whole last line once again 0+1 records in 0+1 records out 7 bytes copied, 0.000102447 s, 68.3 kB/s Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: xt_recent: recent_seq_next should increase position indexVasily Averin
If .next function does not change position index, following .show function will repeat output related to current position index. Without the patch: # dd if=/proc/net/xt_recent/SSH # original file outpt src=127.0.0.4 ttl: 0 last_seen: 6275444819 oldest_pkt: 1 6275444819 src=127.0.0.2 ttl: 0 last_seen: 6275438906 oldest_pkt: 1 6275438906 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 0+1 records in 0+1 records out 204 bytes copied, 6.1332e-05 s, 3.3 MB/s Read after lseek into middle of last line (offset 140 in example below) generates expected end of last line and then unexpected whole last line once again # dd if=/proc/net/xt_recent/SSH bs=140 skip=1 dd: /proc/net/xt_recent/SSH: cannot skip to specified offset 127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 0+1 records in 0+1 records out 132 bytes copied, 6.2487e-05 s, 2.1 MB/s Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: synproxy: synproxy_cpu_seq_next should increase position indexVasily Averin
If .next function does not change position index, following .show function will repeat output related to current position index. Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nf_conntrack: ct_cpu_seq_next should increase position indexVasily Averin
If .next function does not change position index, following .show function will repeat output related to current position index. Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-03mptcp: Only send DATA_FIN with final mappingMat Martineau
When a DATA_FIN is sent in a MPTCP DSS option that contains a data mapping, the DATA_FIN consumes one byte of space in the mapping. In this case, the DATA_FIN should only be included in the DSS option if its sequence number aligns with the end of the mapped data. Otherwise the subflow can send an incorrect implicit sequence number for the DATA_FIN, and the DATA_ACK for that sequence number would not close the MPTCP-level connection correctly. Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03mptcp: Use per-subflow storage for DATA_FIN sequence numberMat Martineau
Instead of reading the MPTCP-level sequence number when sending DATA_FIN, store the data in the subflow so it can be safely accessed when the subflow TCP headers are written to the packet without the MPTCP-level lock held. This also allows the MPTCP-level socket to close individual subflows without closing the MPTCP connection. Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03mptcp: Check connection state before attempting sendMat Martineau
MPTCP should wait for an active connection or skip sending depending on the connection state, as TCP does. This happens before the possible passthrough to a regular TCP sendmsg because the subflow's socket type (MPTCP or TCP fallback) is not known until the connection is complete. This is also relevent at disconnect time, where data should not be sent in certain MPTCP-level connection states. Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03bpf: Add gso_size to __sk_buffWillem de Bruijn
BPF programs may want to know whether an skb is gso. The canonical answer is skb_is_gso(skb), which tests that gso_size != 0. Expose this field in the same manner as gso_segs. That field itself is not a sufficient signal, as the comment in skb_shared_info makes clear: gso_segs may be zero, e.g., from dodgy sources. Also prepare net/bpf/test_run for upcoming BPF_PROG_TEST_RUN tests of the feature. Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200303200503.226217-2-willemdebruijn.kernel@gmail.com
2020-03-03net: dsa: fix phylink_start()/phylink_stop() callsRussell King
Place phylink_start()/phylink_stop() inside dsa_port_enable() and dsa_port_disable(), which ensures that we call phylink_stop() before tearing down phylink - which is a documented requirement. Failure to do so can cause use-after-free bugs. Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03devlink: Introduce devlink port flavour virtualParav Pandit
Currently mlx5 PCI PF and VF devlink devices register their ports as physical port in non-representors mode. Introduce a new port flavour as virtual so that virtual devices can register 'virtual' flavour to make it more clear to users. An example of one PCI PF and 2 PCI virtual functions, each having one devlink port. $ devlink port show pci/0000:06:00.0/1: type eth netdev ens2f0 flavour physical port 0 pci/0000:06:00.2/1: type eth netdev ens2f2 flavour virtual port 0 pci/0000:06:00.3/1: type eth netdev ens2f3 flavour virtual port 0 Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/sched: act_ct: Software offload of established flowsPaul Blakey
Offload nf conntrack processing by looking up the 5-tuple in the zone's flow table. The nf conntrack module will process the packets until a connection is in established state. Once in established state, the ct state pointer (nf_conn) will be restored on the skb from a successful ft lookup. Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/sched: act_ct: Offload established connections to flow tablePaul Blakey
Add a ft entry when connections enter an established state and delete the connections when they leave the established state. The flow table assumes ownership of the connection. In the following patch act_ct will lookup the ct state from the FT. In future patches, drivers will register for callbacks for ft add/del events and will be able to use the information to offload the connections. Note that connection aging is managed by the FT. Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/sched: act_ct: Create nf flow table per zonePaul Blakey
Use the NF flow tables infrastructure for CT offload. Create a nf flow table per zone. Next patches will add FT entries to this table, and do the software offload. Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03ipv6: Use math to point per net sysctls into the appropriate struct netCambda Zhu
The data pointers of ipv6 sysctl are set one by one which is hard to maintain, especially with kconfig. This patch simplifies it by using math to point the per net sysctls into the appropriate struct net, just like what we did for ipv4. Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/ipv6: remove the old peer route if change it to a new oneHangbin Liu
When we modify the peer route and changed it to a new one, we should remove the old route first. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::3 proto kernel metric 256 pref medium This patch depend on the previous patch "net/ipv6: need update peer route when modify metric" to update new peer route after delete old one. Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/ipv6: need update peer route when modify metricHangbin Liu
When we modify the route metric, the peer address's route need also be updated. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 60 pref medium 2001:db8::2 proto kernel metric 60 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 60 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 61 pref medium Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for vendor subcommandJakub Kicinski
Add missing attribute validation for vendor subcommand attributes to the netlink policy. Fixes: 9e58095f9660 ("NFC: netlink: Implement vendor command support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for deactivate targetJakub Kicinski
Add missing attribute validation for NFC_ATTR_TARGET_INDEX to the netlink policy. Fixes: 4d63adfe12dd ("NFC: Add NFC_CMD_DEACTIVATE_TARGET support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for SE APIJakub Kicinski
Add missing attribute validation for NFC_ATTR_SE_INDEX to the netlink policy. Fixes: 5ce3f32b5264 ("NFC: netlink: SE API implementation") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03tipc: add missing attribute validation for MTU propertyJakub Kicinski
Add missing attribute validation for TIPC_NLA_PROP_MTU to the netlink policy. Fixes: 901271e0403a ("tipc: implement configuration of UDP media MTU") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: taprio: add missing attribute validation for txtime delayJakub Kicinski
Add missing attribute validation for TCA_TAPRIO_ATTR_TXTIME_DELAY to the netlink policy. Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-12 20:52:26 +0000